Network Working Group M. Morgenstern
Request for Comments: 4706 M. Dodge
Category: Standards Track ECI Telecom Ltd.
S. Baillie
U. Bonollo
NEC Australia
November 2006
Network Working Group M. Morgenstern
Request for Comments: 4706 M. Dodge
Category: Standards Track ECI Telecom Ltd.
S. Baillie
U. Bonollo
NEC Australia
November 2006
Definitions of Managed Objects for Asymmetric Digital Subscriber Line 2 (ADSL2)
非对称数字用户线路2（ADSL2）的托管对象定义
Status of This Memo
关于下段备忘
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
本文件规定了互联网社区的互联网标准跟踪协议，并要求进行讨论和提出改进建议。有关本协议的标准化状态和状态，请参考当前版本的“互联网官方协议标准”（STD 1）。本备忘录的分发不受限制。
Copyright Notice
版权公告
Copyright (C) The Internet Society (2006).
版权所有（C）互联网协会（2006年）。
Abstract
摘要
This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community. In particular, it describes objects used for managing parameters of the "Asymmetric Digital Subscriber Line" family of interface types: ADSL, ADSL2, ADSL2+, and their variants.
本文档定义了一个管理信息库（MIB）模块，用于Internet社区中的网络管理协议。特别是，它描述了用于管理接口类型“非对称数字用户线”系列参数的对象：ADSL、ADSL2、ADSL2+及其变体。
Table of Contents
目录
1. The Internet-Standard Management Framework ......................3
2. Overview ........................................................3
2.1. Relationship to Other MIBs .................................4
2.1.1. General IF-MIB Integration (RFC 2863) ...............4
2.1.2. Usage of ifTable ....................................5
2.2. IANA Considerations ........................................6
2.3. Conventions Used in the MIB Module .........................6
2.3.1. Naming Conventions ..................................6
2.3.2. Textual Conventions .................................7
2.4. Structure .................................................12
2.5. Persistence ...............................................15
2.6. Line Topology .............................................17
2.7. Counters, Interval Buckets, and Thresholds ................18
2.7.1. Counters Managed ...................................18
2.7.2. Minimum Number of Buckets ..........................19
2.7.3. Interval Buckets Initialization ....................19
2.7.4. Interval Buckets Validity ..........................19
2.8. Profiles ..................................................20
2.8.1. Configuration Profiles and Templates ...............21
2.8.2. Alarm Configuration Profiles and Templates .........22
2.8.3. Managing Profiles and Templates ....................22
2.8.4. Managing Multiple Bearer Channels ..................23
2.9. Notifications .............................................24
3. Definitions ....................................................25
4. Implementation Analysis .......................................155
5. Security Considerations .......................................155
6. Acknowledgements ..............................................163
7. References ....................................................163
7.1. Normative References .....................................163
7.2. Informative References ...................................165
1. The Internet-Standard Management Framework ......................3
2. Overview ........................................................3
2.1. Relationship to Other MIBs .................................4
2.1.1. General IF-MIB Integration (RFC 2863) ...............4
2.1.2. Usage of ifTable ....................................5
2.2. IANA Considerations ........................................6
2.3. Conventions Used in the MIB Module .........................6
2.3.1. Naming Conventions ..................................6
2.3.2. Textual Conventions .................................7
2.4. Structure .................................................12
2.5. Persistence ...............................................15
2.6. Line Topology .............................................17
2.7. Counters, Interval Buckets, and Thresholds ................18
2.7.1. Counters Managed ...................................18
2.7.2. Minimum Number of Buckets ..........................19
2.7.3. Interval Buckets Initialization ....................19
2.7.4. Interval Buckets Validity ..........................19
2.8. Profiles ..................................................20
2.8.1. Configuration Profiles and Templates ...............21
2.8.2. Alarm Configuration Profiles and Templates .........22
2.8.3. Managing Profiles and Templates ....................22
2.8.4. Managing Multiple Bearer Channels ..................23
2.9. Notifications .............................................24
3. Definitions ....................................................25
4. Implementation Analysis .......................................155
5. Security Considerations .......................................155
6. Acknowledgements ..............................................163
7. References ....................................................163
7.1. Normative References .....................................163
7.2. Informative References ...................................165
For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to Section 7 of RFC 3410 [RFC3410].
有关描述当前互联网标准管理框架的文件的详细概述，请参阅RFC 3410[RFC3410]第7节。
Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580].
托管对象通过虚拟信息存储（称为管理信息库或MIB）进行访问。MIB对象通常通过简单网络管理协议（SNMP）进行访问。MIB中的对象是使用管理信息结构（SMI）中定义的机制定义的。本备忘录规定了符合SMIv2的MIB模块，如STD 58、RFC 2578[RFC2578]、STD 58、RFC 2579[RFC2579]和STD 58、RFC 2580[RFC2580]所述。
This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managing ADSL, ADSL2, and ADSL2+ lines.
本文档定义了一个管理信息库（MIB）模块，用于互联网社区中的网络管理协议，用于管理ADSL、ADSL2和ADSL2+线路。
The MIB module described in RFC 2662 [RFC2662] describes objects used for managing Asymmetric Bit-Rate DSL (ADSL) interfaces per [T1E1.413], [G.992.1], and [G.992.2]. These object descriptions are based upon the specifications for the ADSL Embedded Operations Channel (EOC) as defined in American National Standards Institute (ANSI) T1E1.413/1995 [T1E1.413] and International Telecommunication Union (ITU-T) G.992.1 [G.992.1] and G.992.2 [G.992.2].
RFC 2662[RFC2662]中描述的MIB模块描述了用于按照[T1E1.413]、[G.992.1]和[G.992.2]管理非对称比特率DSL（ADSL）接口的对象。这些对象描述基于美国国家标准协会（ANSI）T1E1.413/1995[T1E1.413]和国际电信联盟（ITU-T）G.992.1[G.992.1]和G.992.2[G.992.2]中定义的ADSL嵌入式操作信道（EOC）规范。
This document does not obsolete RFC 2662 [RFC2662], but rather provides a more comprehensive management model that includes the ADSL2 and ADSL2+ technologies per G.992.3, G.992.4, and G.992.5 ([G.992.3], [G.992.4], and [G.992.5] respectively). In addition, objects have been added to improve the management of ADSL, ADSL2, and ADSL2+ lines.
本文件并未废弃RFC 2662[RFC2662]，而是提供了一个更全面的管理模型，其中包括符合G.992.3、G.992.4和G.992.5的ADSL2和ADSL2+技术（分别为[G.992.3]、[G.992.4]和[G.992.5]）。此外，还添加了对象以改进ADSL、ADSL2和ADSL2+线路的管理。
Additionally, the management framework for New Generation ADSL lines specified [TR-90] by the Digital Subscriber Line Forum (DSLF) has been taken into consideration. That framework is based on ITU-T G.997.1 standard [G.997.1] as well as on two amendments: ([G.997.1am1] and [G.997.1am2]). This document refers to all three documents as G.997.1. That is, a MIB attribute whose REFERENCE section provides a paragraph number in ITU-T G.997.1 is actually originated from either G.997.1 [G.997.1] or one of its amendment documents.
此外，还考虑了数字用户线路论坛（DSLF）指定的[TR-90]新一代ADSL线路管理框架。该框架基于ITU-T G.997.1标准[G.997.1]以及两个修正案（[G.997.1am1]和[G.997.1am2]）。本文件引用了G.997.1中的所有三个文件。也就是说，其参考部分在ITU-T G.997.1中提供段落编号的MIB属性实际上来源于G.997.1[G.997.1]或其修订文件之一。
Note that the revised ITU-T G.997.1 standard also refers to the next generation of VDSL technology, known as VDSL2, as per ITU-T G.993.2 [G.993.2]. However, managing VDSL2 lines is currently beyond the scope of this document.
请注意，根据ITU-T G.993.2[G.993.2]，修订后的ITU-T G.997.1标准还参考了下一代VDSL技术，称为VDSL2。但是，管理VDSL2线路目前超出了本文档的范围。
The MIB module is located in the MIB tree under MIB 2 transmission, as discussed in the IANA Considerations section of this document.
MIB模块位于MIB 2传输下的MIB树中，如本文档IANA注意事项部分所述。
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119].
本文件中的关键词“必须”、“不得”、“要求”、“应”、“不应”、“应”、“不应”、“建议”、“可”和“可选”应按照RFC 2119[RFC2119]中所述进行解释。
This section outlines the relationship of this MIB module with other MIB modules described in RFCs. Specifically, IF-MIB as presented in RFC 2863 [RFC2863] is discussed.
本节概述此MIB模块与RFCs中描述的其他MIB模块的关系。具体地说，将讨论RFC 2863[RFC2863]中提出的IF-MIB。
The ADSL2 Line MIB specifies the detailed attributes of a data interface. As such, it needs to integrate with RFC 2863 [RFC2863]. The IANA has assigned the following ifTypes, which may be applicable for ADSL lines:
ADSL2行MIB指定数据接口的详细属性。因此，它需要与RFC 2863[RFC2863]集成。IANA分配了以下IFT类型，这些IFT类型可能适用于ADSL线路：
IANAifType ::= TEXTUAL-CONVENTION
...
SYNTAX INTEGER {
...
channel(70), -- Channel
adsl(94), -- Asymmetric Digital Subscriber Loop
...
interleave(124), -- Interleaved Channel
fast(125), -- Fast Channel
...
adsl2plus(238), -- Asymmetric Digital Subscriber Loop Version 2,
Version 2 Plus, and all variants
...
}
IANAifType ::= TEXTUAL-CONVENTION
...
SYNTAX INTEGER {
...
channel(70), -- Channel
adsl(94), -- Asymmetric Digital Subscriber Loop
...
interleave(124), -- Interleaved Channel
fast(125), -- Fast Channel
...
adsl2plus(238), -- Asymmetric Digital Subscriber Loop Version 2,
Version 2 Plus, and all variants
...
}
ADSL lines that are identified with ifType=adsl(94) MUST be managed with the MIB specified by RFC 2662. ADSL, ADSL2, and ADSL2+ lines identified with ifType=adsl2plus(238) MUST be managed with the MIB specified by this document.
用ifType=ADSL（94）标识的ADSL线路必须使用RFC 2662指定的MIB进行管理。必须使用本文档指定的MIB管理ifType=adsl2plus（238）标识的ADSL、ADSL2和ADSL2+线路。
In any case, the SNMP agent may use either ifType=interleave(124) or fast(125) for each channel, e.g., depending on whether or not it is capable of using an interleaver on that channel. It may use the ifType=channel(70) when all channels are capable of using an interleaver (e.g., for ADSL2 XTUs).
在任何情况下，SNMP代理可以对每个信道使用ifType=交织（124）或fast（125），例如，取决于它是否能够在该信道上使用交织器。当所有信道都能够使用交织器（例如，对于ADSL2 XTU）时，它可以使用ifType=信道（70）。
Note that the ifFixedLengthGroup from RFC 2863 [RFC2863] MUST be supported and that the ifRcvAddressGroup does not apply to this MIB module.
请注意，必须支持来自RFC 2863[RFC2863]的ifFixedLengthGroup，并且IFRCVADDRESGROUP不适用于此MIB模块。
The MIB branch identified by ifType contains tables appropriate for the interface types described above. Most such tables extend the ifEntry table and are indexed by ifIndex. For interfaces in systems implementing this MIB module, those table entries indexed by ifIndex MUST be persistent.
ifType标识的MIB分支包含适用于上述接口类型的表。大多数这样的表扩展了ifEntry表，并由ifIndex索引。对于实现此MIB模块的系统中的接口，ifIndex索引的那些表项必须是持久的。
The following attributes are part of the mandatory ifGeneralInformationGroup in the Interfaces MIB [RFC2863] and are not duplicated in the ADSL2 Line MIB.
以下属性是接口MIB[RFC2863]中必需的IFGeneralInformation组的一部分，在ADSL2线路MIB中不重复。
===================================================================
===================================================================
ifIndex Interface index.
iIndex接口索引。
ifDescr See interfaces MIB.
ifDescr请参见接口MIB。
ifType adsl2plus(238) or channel(70) or interleave(124) or fast(125).
ifType adsl2plus（238）或channel（70）或interleave（124）或fast（125）。
ifSpeed Set as appropriate.
如果速度设置合适。
ifPhysAddress This object MUST have an octet string with zero length.
ifPhysAddress此对象必须具有长度为零的八位字节字符串。
ifAdminStatus See interfaces MIB.
ifAdminStatus请参阅接口MIB。
ifOperStatus See interfaces MIB.
ifOperStatus请参见接口MIB。
ifLastChange See interfaces MIB.
iFastChange请参见接口MIB。
ifName See interfaces MIB.
ifName请参阅接口MIB。
ifAlias See interfaces MIB.
IFALIA见接口MIB。
ifLinkUpDownTrapEnable Default to enabled(1).
iFlinkUpDowntrap默认值为enabled（1）。
ifHighSpeed Set as appropriate.
如果高速设置合适。
ifConnectorPresent Set as appropriate.
ifConnectorPresent可根据需要进行设置。
===================================================================
Figure 1: Use of ifTable Objects
===================================================================
Figure 1: Use of ifTable Objects
The IANA has allocated ifType=adsl2plus(238) for Asymmetric Digital Subscriber Loop Version 2. A separate ifType number was necessary to distinguish between ADSL lines that are managed with the RFC 2662 management model and ADSL/ADSL2 and ADSL2+ lines managed with the model defined in this document.
IANA为非对称数字用户环路版本2分配了ifType=adsl2plus（238）。为了区分使用RFC 2662管理模型管理的ADSL线路和使用本文件中定义的模型管理的ADSL/ADSL2和ADSL2+线路，需要单独的ifType编号。
Also, the IANA has assigned transmission number 238 to the ADSL2-LINE-MIB module.
此外，IANA已将传输编号238分配给ADSL2-LINE-MIB模块。
An assignment was in fact done when RFC 2662 was published, but as this MIB does not obsolete RFC 2662, it required a new assignment from IANA.
实际上，在发布RFC 2662时已完成分配，但由于此MIB并未淘汰RFC 2662，因此需要IANA的新分配。
ATU ADSL Transceiver Unit ATU-C ATU at the Central office end (i.e., network operator). ATU-R ATU at the Remote end (i.e., subscriber end of the loop). XTU A terminal unit; either an ATU-C or an ATU-R. CRC Cyclic Redundancy Check DELT Dual Ended Loop Test ES Errored Second FEC Forward Error Correction LOF Loss Of Frame LOS Loss Of Signal LOSS LOS Seconds SES Severely-Errored Second SNR Signal-to-Noise Ratio UAS Unavailable Seconds
ATU ADSL收发器单元ATU-C ATU位于中央局端（即网络运营商）。远程端（即环路的用户端）的ATU-R ATU。XTU终端单元；ATU-C或ATU-R。CRC循环冗余校验DELT双端环路测试ES错误第二FEC前向纠错LOF帧丢失LOS信号丢失LOS秒SES严重错误第二SNR信噪比UAS不可用秒
The following textual conventions are defined to reflect the line topology in the MIB module (further discussed in the following section), the various transmission modes, power states, synchronization states, possible values for various configuration parameters, status parameters, and other parameter types.
定义以下文本约定以反映MIB模块中的线路拓扑（下一节将进一步讨论）、各种传输模式、电源状态、同步状态、各种配置参数的可能值、状态参数和其他参数类型。
o Adsl2Unit:
o ADSL2单元：
Attributes with this syntax uniquely identify each unit in the ADSL/ADSL2/ADSL2+ link. It mirrors the EOC addressing mechanism:
具有此语法的属性唯一标识ADSL/ADSL2/ADSL2+链路中的每个单元。它反映了EOC寻址机制：
atuc(1) - Central office ADSL transceiver unit (ATU-C). atur(2) - Remote ADSL transceiver unit (ATU-R).
atuc（1）-中央局ADSL收发器单元（ATU-C）。atur（2）-远程ADSL收发器单元（ATU-R）。
o Adsl2Direction:
o ADSL2方向：
Attributes with this syntax uniquely identify a transmission direction in an ADSL/ADSL2/ADSL2+ link. Upstream direction is a transmission from the remote end (ATU-R) towards the central office end (ATU-C), while downstream direction is a transmission from the ATU-C towards the ATU-R.
具有此语法的属性唯一标识ADSL/ADSL2/ADSL2+链路中的传输方向。上游方向是从远程端（ATU-R）到中央局端（ATU-C）的传输，而下游方向是从ATU-C到ATU-R的传输。
upstream(1) - Transmission from the ATU-R to the ATU-C. downstream(2) - Transmission from the ATU-C to the ATU-R.
上游（1）-从ATU-R到ATU-C的传输。下游（2）-从ATU-C到ATU-R的传输。
o Adsl2TransmissionModeType:
o ADSL2TransmissionModelType：
Attributes with this syntax reference the list of possible transmission modes for ADSL/ADSL2 or ADSL2+.
具有此语法的属性引用ADSL/ADSL2或ADSL2+的可能传输模式列表。
Specified as a BITS construct, there are currently a few dozen transmission modes in the list.
指定为BITS结构，列表中目前有几十种传输模式。
o Adsl2RaMode:
o Adsl2RaMode：
Attributes with this syntax reference if and how Rate-Adaptive synchronization is being used on the respective ADSL/ADSL2 or ADSL2+ link:
具有此语法参考的属性，如果以及如何在相应的ADSL/ADSL2或ADSL2+链路上使用速率自适应同步：
manual(1) - No Rate-Adaptation. The initialization process attempts to synchronize to a specified rate. raInit(2) - Rate-Adaptation during initialization process only, which attempts to synchronize to a rate between minimum and maximum specified values.
手动（1）-无速率自适应。初始化进程尝试同步到指定的速率。raInit（2）-仅在初始化过程中进行速率自适应，尝试同步到最小和最大指定值之间的速率。
dynamicRa(3) - Dynamic Rate-Adaptation during initialization process as well as during SHOWTIME.
dynamicRa（3）-初始化过程中和SHOWTIME期间的动态速率自适应。
o Adsl2InitResult:
o ADSL2结果：
Attributes with this syntax reference the recent result of a full initialization attempt:
具有此语法的属性引用了完整初始化尝试的最新结果：
noFail(0) - Successful initialization. configError(1) - Configuration failure. configNotFeasible(2) - Configuration details not supported. commFail(3) - Communication failure. noPeerAtu(4) - Peer ADSL Transceiver Unit (ATU) not detected. otherCause(5) - Other initialization failure reason.
noFail（0）-初始化成功。配置错误（1）-配置失败。ConfigNotExecutable（2）-不支持配置详细信息。通信故障（3）-通信故障。noPeerAtu（4）-未检测到对等ADSL收发器单元（ATU）。其他原因（5）-其他初始化失败原因。
o Adsl2OperationModes:
o ADSL2操作模式：
Attributes with this syntax uniquely identify an ADSL mode, which is a category associated with each transmission mode defined for the ADSL/ADSL2 or ADSL2+ link. Part of the line configuration profile depends on the ADSL Mode:
具有此语法的属性唯一标识ADSL模式，ADSL模式是与为ADSL/ADSL2或ADSL2+链路定义的每个传输模式相关联的类别。线路配置配置文件的一部分取决于ADSL模式：
Specified as an enumeration construct, there are currently a few dozen transmission modes in the list.
指定为枚举构造，列表中当前有几十种传输模式。
o Adsl2PowerMngState:
o Adsl2PowerMngState：
Attributes with this syntax uniquely identify each power management state defined for the ADSL/ADSL2 or ADSL2+ link:
具有此语法的属性唯一标识为ADSL/ADSL2或ADSL2+链路定义的每个电源管理状态：
l0(1) - L0 - Full power management state. l1(2) - L1 - Low power management state (for G.992.2). l2(3) - L2 - Low power management state (for G.992.3, G.992.4, and G.992.5). l3(4) - L3 - Idle power management state.
l0（1）-l0-全功率管理状态。l1（2）-l1-低功耗管理状态（适用于G.992.2）。l2（3）-l2-低功耗管理状态（适用于G.992.3、G.992.4和G.992.5）。l3（4）-l3-空闲电源管理状态。
o Adsl2ConfPmsForce:
o Adsl2ConfPmsForce：
Attributes with this syntax are configuration parameters that reference the desired power management state for the ADSL/ADSL2 or ADSL2+ link:
具有此语法的属性是参考ADSL/ADSL2或ADSL2+链路所需电源管理状态的配置参数：
l3toL0(0) - Perform a transition from L3 to L0 (Full power management state). l0toL2(2) - Perform a transition from L0 to L2 (Low power management state).
l3toL0（0）-执行从L3到L0（全电源管理状态）的转换。l0toL2（2）-执行从L0到L2（低功耗管理状态）的转换。
l0orL2toL3(3) - Perform a transition into L3 (Idle power management state).
l0orL2toL3（3）-执行到L3（空闲电源管理状态）的转换。
o Adsl2LConfProfPmMode:
o ADSL2L模式：
Attributes with this syntax are configuration parameters that reference the power modes/states into which the ATU-C or ATU-R may autonomously transit.
具有此语法的属性是参考ATU-C或ATU-R可自动过渡到的电源模式/状态的配置参数。
This is a BITS structure that allows control of the following transit options:
这是一种BITS结构，允许控制以下传输选项：
allowTransitionsToIdle(0) - XTU may autonomously transit to idle (L3) state. allowTransitionsToLowPower(1) - XTU may autonomously transit to low-power (L2) state.
allowTransitionsToIdle（0）-XTU可以自动过渡到idle（L3）状态。allowTransitionsToLowPower（1）-XTU可以自动过渡到低功耗（L2）状态。
o Adsl2LineLdsf:
o ADSL2LINEDSF：
Attributes with this syntax are configuration parameters that control the Loop Diagnostic mode for the ADSL/ADSL2 or ADSL2+ link:
具有此语法的属性是控制ADSL/ADSL2或ADSL2+链路环路诊断模式的配置参数：
inhibit(0) - Inhibit Loop Diagnostic mode. force(1) - Force/Initiate Loop Diagnostic mode.
抑制（0）-抑制回路诊断模式。强制（1）-强制/启动回路诊断模式。
o Adsl2LdsfResult:
o ADSL2LDFRESULT：
Attributes with this syntax are status parameters that report the result of the recent Loop Diagnostic mode issued for the ADSL/ADSL2 or ADSL2+ link:
具有此语法的属性是状态参数，用于报告为ADSL/ADSL2或ADSL2+链路发出的最近环路诊断模式的结果：
none(1) - The default value, in case loop diagnostics mode forced (LDSF) was never requested for the associated line. success(2) - The recent command completed successfully. inProgress(3) - The Loop Diagnostics process is in progress. unsupported(4) - The NE or the line card doesn't support LDSF. cannotRun(5) - The NE cannot initiate the command, due to a nonspecific reason. aborted(6) - The Loop Diagnostics process aborted. failed(7) - The Loop Diagnostics process failed. illegalMode(8) - The NE cannot initiate the command, due to the specific mode of the relevant line.
无（1）-如果从未为相关线路请求强制循环诊断模式（LDSF），则为默认值。成功（2）-最近的命令已成功完成。正在进行（3）-回路诊断过程正在进行中。不支持（4）-网元或线路卡不支持LDSF。cannotRun（5）-由于非特定原因，网元无法启动该命令。中止（6）-回路诊断过程中止。失败（7）-回路诊断过程失败。非法模式（8）-由于相关线路的特定模式，网元无法启动命令。
adminUp(9) - The NE cannot initiate the command because the relevant line is administratively 'Up'. tableFull(10) - The NE cannot initiate the command, due to reaching the maximum number of rows in the results table. noResources(11) - The NE cannot initiate the command, due to lack of internal memory resources.
adminUp（9）-网元无法启动命令，因为相关行在管理上为“Up”。tableFull（10）-由于达到结果表中的最大行数，网元无法启动命令。noResources（11）-由于缺少内部内存资源，网元无法启动该命令。
o Adsl2SymbolProtection:
o ADSL2SYMBOL保护：
Attributes with this syntax are configuration parameters that reference the minimum-length impulse noise protection (INP) in terms of number of symbols:
具有此语法的属性是根据符号数参考最小长度脉冲噪声保护（INP）的配置参数：
noProtection(1) - INP not required. halfSymbol(2) - INP length = 1/2 symbol. singleSymbol(3) - INP length = 1 symbol. twoSymbols(4) - INP length = 2 symbols. threeSymbols(5) - INP length = 3 symbols. fourSymbols(6) - INP length = 4 symbols. fiveSymbols(7) - INP length = 5 symbols. sixSymbols(8) - INP length = 6 symbols. sevenSymbols(9) - INP length = 7 symbols. eightSymbols(10) - INP length = 8 symbols. nineSymbols(11) - INP length = 9 symbols. tenSymbols(12) - INP length = 10 symbols. elevenSymbols(13) - INP length = 11 symbols. twelveSymbols(14) - INP length = 12 symbols. thirteeSymbols(15) - INP length = 13 symbols. fourteenSymbols(16) - INP length = 14 symbols. fifteenSymbols(17) - INP length = 15 symbols. sixteenSymbols(18) - INP length = 16 symbols.
无保护（1）-不需要INP。半符号（2）-INP长度=1/2符号。单符号（3）-INP长度=1符号。两个符号（4）-INP长度=2个符号。三个符号（5）-INP长度=3个符号。四个符号（6）-INP长度=4个符号。五个符号（7）-输入长度=5个符号。六个符号（8）-INP长度=6个符号。七个符号（9）-INP长度=7个符号。八个符号（10）-INP长度=8个符号。九个符号（11）-INP长度=9个符号。张力符号（12）-INP长度=10个符号。elevenSymbols（13）-INP长度=11个符号。十二个符号（14）-INP长度=12个符号。第三十个符号（15）-INP长度=13个符号。十四个符号（16）-INP长度=14个符号。第五个符号（17）-输入长度=15个符号。十六个符号（18）-INP长度=16个符号。
o Adsl2MaxBer:
o Adsl2MaxBer：
Attributes with this syntax are configuration parameters that reference the maximum Bit Error Rate (BER):
具有此语法的属性是引用最大误码率（BER）的配置参数：
eminus3(1) - Maximum BER=E^-3. eminus5(2) - Maximum BER=E^-5. eminus7(3) - Maximum BER=E^-7.
Emius3（1）-最大误码率=E^-3。Emius5（2）-最大误码率=E^-5。埃米努斯7（3）-最大误码率=E^-7。
o Adsl2ScMaskDs:
o ADSL2SCMAKDS：
Attributes with this syntax are configuration parameters that reference the downstream sub-carrier mask. It is a bitmap of up to 512 bits.
具有此语法的属性是引用下游子载波掩码的配置参数。它是高达512位的位图。
o Adsl2ScMaskUs:
o Adsl2ScMaskUs：
Attributes with this syntax are configuration parameters that reference the upstream sub-carrier mask. It is a bitmap of up to 64 bits.
具有此语法的属性是引用上游子载波掩码的配置参数。它是高达64位的位图。
o Adsl2RfiDs:
o ADSL2RFID：
Attributes with this syntax are configuration parameters that reference the downstream notch filters. It is a bitmap of up to 512 bits.
具有此语法的属性是引用下游陷波滤波器的配置参数。它是高达512位的位图。
o Adsl2PsdMaskDs:
o Adsl2PsdMaskDs：
Attributes with this syntax are configuration parameters that reference the downstream power spectrum density (PSD) mask. It is a structure of up to 32 breakpoints, where each breakpoint occupies 3 octets.
具有此语法的属性是引用下游功率谱密度（PSD）掩码的配置参数。它是一个最多32个断点的结构，其中每个断点占用3个八位字节。
o Adsl2PsdMaskUs:
o Adsl2PsdMaskUs：
Attributes with this syntax are configuration parameters that reference the upstream power spectrum density (PSD) mask. It is a structure of up to 4 breakpoints, where each breakpoint occupies 3 octets.
具有此语法的属性是参考上游功率谱密度（PSD）掩码的配置参数。它是一个最多由4个断点组成的结构，其中每个断点占用3个八位字节。
o Adsl2Tssi:
o Adsl2Tssi：
Attributes with this syntax are status parameters that reference the transmit spectrum shaping (TSSi). It is a structure of up to 32 breakpoints, where each breakpoint occupies 3 octets.
具有此语法的属性是引用发射频谱成形（TSSi）的状态参数。它是一个最多32个断点的结构，其中每个断点占用3个八位字节。
o Adsl2LastTransmittedState:
o Adsl2LastTransmittedState：
Attributes with this syntax reference the list of initialization states for ADSL/ADSL2 or ADSL2+ modems. The list of states for CO side modems (ATU-Cs) is different from the list of states for the remote side modems (ATU-Rs).
具有此语法的属性引用ADSL/ADSL2或ADSL2+调制解调器的初始化状态列表。CO侧调制解调器（ATU Cs）的状态列表与远程侧调制解调器（ATU Rs）的状态列表不同。
Specified as an enumeration type, there are currently a few dozen states in the list per each unit side (i.e., ATU-C or ATU-R).
指定为枚举类型，每个机组侧的列表中当前有几十个状态（即ATU-C或ATU-R）。
o Adsl2LineStatus:
o ADSL2线路状态：
Attributes with this syntax are status parameters that reflect the failure status for a given endpoint of ADSL/ADSL2 or ADSL2+ link.
具有此语法的属性是状态参数，反映ADSL/ADSL2或ADSL2+链路的给定端点的故障状态。
This is a BITS structure that can report the following failures:
这是一个BITS结构，可报告以下故障：
noDefect(0) - This bit position positively reports that no defect or failure exists. lossOfFrame(1) - Loss of frame synchronization. lossOfSignal(2) - Loss of signal. lossOfPower(3) - Loss of power. Usually this failure may be reported for ATU-Rs only. initFailure(4) - Recent initialization process failed. Never active on ATU-R.
noDefect（0）-此位位置积极报告不存在缺陷或故障。lossOfFrame（1）-帧同步丢失。信号丢失（2）-信号丢失。功率损失（3）-功率损失。通常，仅针对ATU Rs报告此故障。initFailure（4）-最近的初始化过程失败。ATU-R上从未激活。
o Adsl2ChAtmStatus:
o Adsl2ChAtmStatus：
Attributes with this syntax are status parameters that reflect the failure status for Transmission Convergence (TC) layer of a given ATM interface (data path over an ADSL/ADSL2 or ADSL2+ link).
具有此语法的属性是状态参数，反映给定ATM接口（ADSL/ADSL2或ADSL2+链路上的数据路径）传输汇聚（TC）层的故障状态。
This is a BITS structure that can report the following failures:
这是一个BITS结构，可报告以下故障：
noDefect(0) - This bit position positively reports that no defect or failure exists. noCellDelineation(1) - The link was successfully initialized but cell delineation was never acquired on the associated ATM data path. lossOfCellDelineation(2) - Loss of cell delineation on the associated ATM data path.
noDefect（0）-此位位置积极报告不存在缺陷或故障。NocellRefraction（1）-链路已成功初始化，但从未在关联的ATM数据路径上获取信元描述。LossOfCellDescription（2）-相关ATM数据路径上的信元划分丢失。
o Adsl2ChPtmStatus:
o Adsl2ChPtmStatus：
Attributes with this syntax are status parameters that reflect the failure status for a given PTM interface (packet data path over an ADSL/ADSL2 or ADSL2+ link).
具有此语法的属性是反映给定PTM接口（ADSL/ADSL2或ADSL2+链路上的分组数据路径）故障状态的状态参数。
This is a BITS structure that can report the following failures:
这是一个BITS结构，可报告以下故障：
noDefect(0) - This bit position positively reports that no defect or failure exists. outOfSync(1) - Out of synchronization.
noDefect（0）-此位位置积极报告不存在缺陷或故障。不同步（1）-不同步。
The MIB module is structured into following MIB groups:
MIB模块由以下MIB组构成：
o Line Configuration, Maintenance, and Status Group:
o 线路配置、维护和状态组：
This group supports MIB objects for configuring parameters for the ADSL/ADSL2 or ADSL2+ line and retrieving line status information.
此组支持MIB对象，用于配置ADSL/ADSL2或ADSL2+线路的参数并检索线路状态信息。
It also supports MIB objects for configuring a requested power state or initiating a Dual Ended Loop Test (DELT) process in the ADSL/ADSL2 or ADSL2+ line. It contains the following table:
它还支持MIB对象，用于在ADSL/ADSL2或ADSL2+线路中配置请求的电源状态或启动双端环路测试（DELT）进程。它包含下表：
- adsl2LineTable
- adsl2LineTable
o Channel Status Group:
o 频道状态组：
This group supports MIB objects for retrieving channel layer status information. It contains the following table:
此组支持用于检索通道层状态信息的MIB对象。它包含下表：
- adsl2ChannelStatusTable
- ADSL2信道状态表
o Subcarrier Status Group:
o 子载波状态组：
This group supports MIB objects for retrieving the sub-carrier layer status information, mostly collected by a Dual Ended Loop Test (DELT) process. It contains the following table:
该组支持用于检索子载波层状态信息的MIB对象，这些信息主要由双端环路测试（DELT）过程收集。它包含下表：
- adsl2SCStatusTable
- ADSL2SCStatus表
o Unit Inventory Group:
o 库存组单位：
This group supports MIB objects for retrieving Unit inventory information about units in ADSL/ADSL2 or ADSL2+ lines via the EOC. It contains the following table:
此组支持MIB对象，用于通过EOC检索有关ADSL/ADSL2或ADSL2+线路中单元的单元库存信息。它包含下表：
- adsl2LineInventoryTable
- adsl2LineInventoryTable
o Current Performance Group:
o 当前绩效组：
This group supports MIB objects that provide the current performance information relating to ADSL/ADSL2 and ADSL2+ line, units and channels level. It contains the following tables:
此组支持MIB对象，这些对象提供与ADSL/ADSL2和ADSL2+线路、单元和通道级别相关的当前性能信息。它包含以下表格：
- adsl2PMLineCurrTable - adsl2PMLineCurrInitTable - adsl2PMChCurrTable
- adsl2PMLineCurrTable-adsl2PMLineCurrInitTable-adsl2PMChCurrTable
o 15-Minute Interval Performance Group:
o 15分钟间隔表演组：
This group supports MIB objects that provide historic performance information relating to ADSL/ADSL2 and ADSL2+ line, units and channels level in 15-minute intervals. It contains the following tables:
此组支持MIB对象，这些对象以15分钟的间隔提供有关ADSL/ADSL2和ADSL2+线路、单元和通道级别的历史性能信息。它包含以下表格：
- adsl2PMLineHist15MinTable - adsl2PMLineInitHist15MinTable - adsl2PMChHist15MinTable
- ADSL2PMLINEIST15可维护-ADSL2PMLINEIST15可维护-ADSL2PMCHHIST15可维护
o 1-Day Interval Performance Group:
o 1天间隔性能组：
This group supports MIB objects that provide historic performance information relating to ADSL/ADSL2 and ADSL2+ line, units and channels level in 1-day intervals. It contains the following tables:
此组支持MIB对象，这些对象以1天的间隔提供与ADSL/ADSL2和ADSL2+线路、单元和通道级别相关的历史性能信息。它包含以下表格：
- adsl2PMLineHist1DayTable - adsl2PMLineInitHist1DayTable - adsl2PMChHist1DTable
- ADSL2PMLINEHIST1日期表-ADSL2PMLINEINITHIST1日期表-ADSL2PMCHHIST1日期表
o Configuration Template and Profile Group:
o 配置模板和配置文件组：
This group supports MIB objects for defining configuration profiles for ADSL/ADSL2 and ADSL2+ lines and channels, as well as configuration templates. Each configuration template is comprised of one line configuration profile and one or more channel configuration profiles. This group contains the following tables:
此组支持MIB对象，用于定义ADSL/ADSL2和ADSL2+线路和通道的配置配置文件，以及配置模板。每个配置模板由一个线路配置文件和一个或多个通道配置文件组成。该组包含以下表格：
- adsl2LineConfTemplateTable - adsl2LineConfProfTable - adsl2LineConfProfModeSpecTable - adsl2ChConfProfileTable
- adsl2LineConfTemplateTable-adsl2LineConfProfTable-adsl2LineConfProfModeSpecTable-ADSL2HConFProfileTable
o Alarm Configuration Template and Profile Group:
o 报警配置模板和配置文件组：
This group supports MIB objects for defining alarm profiles for ADSL/ADSL2 and ADSL2+ lines and channels, as well as alarm templates. Each alarm template is comprised of one line alarm profile and one or more channel alarm profiles. This group contains the following tables:
此组支持MIB对象，用于定义ADSL/ADSL2和ADSL2+线路和通道的报警配置文件，以及报警模板。每个报警模板由一个线路报警配置文件和一个或多个通道报警配置文件组成。该组包含以下表格：
- adsl2LineAlarmConfTemplateTable - adsl2LineAlarmConfProfileTable - adsl2ChAlarmConfProfileTable
- adsl2LineAlarmConfTemplateTable-adsl2LineAlarmConfProfileTable-adsl2ChAlarmConfProfileTable
o Notifications Group:
o 通知组：
This group defines the notifications supported for ADSL/ADSL2 and ADSL2+ lines:
此组定义ADSL/ADSL2和ADSL2+线路支持的通知：
- adsl2LinePerfFECSThreshAtuc - adsl2LinePerfFECSThreshAtur - adsl2LinePerfESThreshAtuc
- ADSL2线路性能阈值-ADSL2线路性能阈值-ADSL2线路性能阈值
- adsl2LinePerfESThreshAtur - adsl2LinePerfSESThreshAtuc - adsl2LinePerfSESThreshAtur - adsl2LinePerfLOSSThreshAtuc - adsl2LinePerfLOSSThreshAtur - adsl2LinePerfUASThreshAtuc - adsl2LinePerfUASThreshAtur - adsl2LinePerfCodingViolationsThreshAtuc - adsl2LinePerfCodingViolationsThreshAtur - adsl2LinePerfCorrectedThreshAtuc - adsl2LinePerfCorrectedThreshAtur - adsl2LinePerfFailedFullInitThresh - adsl2LinePerfFailedShortInitThresh - adsl2LineStatusChangeAtuc - adsl2LineStatusChangeAtur
- ADSL2线路性能阈值-ADSL2线路性能阈值-ADSL2线路性能阈值-ADSL2线路性能阈值-ADSL2线路性能阈值-ADSL2线路性能阈值-ADSL2线路性能阈值-ADSL2线路性能阈值-ADSL2线路性能阈值-ADSL2线路性能阈值-ADSL2线路性能违规-ADSL2线路性能已纠正阈值-ADSL2线路性能修正阈值-ADSL2线路性能故障完整初始化阈值-ADSL2线路性能故障简短初始化阈值-ADSL2线路状态更改ATUC-ADSL2线路状态更改
All read-create objects and most read-write objects defined in this MIB module SHOULD be stored persistently. Following is an exhaustive list of these persistent objects:
此MIB模块中定义的所有读创建对象和大多数读写对象都应持久存储。以下是这些持久对象的详尽列表：
adsl2LineCnfgTemplate adsl2LineAlarmCnfgTemplate adsl2LineCmndConfPmsf adsl2LineCmndConfLdsf adsl2LineCmndAutomodeColdStart adsl2LConfTempTemplateName adsl2LConfTempLineProfile adsl2LConfTempChan1ConfProfile adsl2LConfTempChan1RaRatioDs adsl2LConfTempChan1RaRatioUs adsl2LConfTempChan2ConfProfile adsl2LConfTempChan2RaRatioDs adsl2LConfTempChan2RaRatioUs adsl2LConfTempChan3ConfProfile adsl2LConfTempChan3RaRatioDs adsl2LConfTempChan3RaRatioUs adsl2LConfTempChan4ConfProfile adsl2LConfTempChan4RaRatioDs adsl2LConfTempChan4RaRatioUs adsl2LConfTempRowStatus adsl2LConfProfProfileName adsl2LConfProfScMaskDs adsl2LConfProfScMaskUs adsl2LConfProfRfiBandsDs adsl2LConfProfRaModeDs adsl2LConfProfRaModeUs
adsl2LineCnfgTemplate adsl2LineAlarmCnfgTemplate adsl2LineCmndConfPmsf ADSL2LineCmNDConfDSF ADSL2LineCmNDConfModeColdStart ADSL2ConfTemplate模板名称ADSL2ConfTemplineProfile ADSL2ConfTempChan1协议文件ADSL2ConfTempChan1协议文件ADSL2ConfTempChan1协议文件ADSL2ConfTempChan1协议文件ADSL2ConfTempChan2协议文件ADSL2ConfTempChan2协议文件ADSL2ConfTempChan2随机ADSL2ConfTempChan3 CONF配置文件ADSL2ConfTempChan3 RARATIODS ADSL2ConfTempChan3随机ADSL2ConfTempChan4 CONF配置文件ADSL2ConfTempChan4 RATIODS ADSL2ConfTempChan4随机ADSL2ConfTempRowStatus ADSL2ConfProfProfProfile名称ADSL2ConfProfMasKDS ADSL2ConfTempChan ADSL2ConfMaskus ADSL2ConfProfSprofMaskus ADSL2L2adsl2LConfProfRaModeDs adsl2LConfProfRaModeUs
adsl2LConfProfRaUsNrmDs adsl2LConfProfRaUsNrmUs adsl2LConfProfRaUsTimeDs adsl2LConfProfRaUsTimeUs adsl2LConfProfRaDsNrmsDs adsl2LConfProfRaDsNrmsUs adsl2LConfProfRaDsTimeDs adsl2LConfProfRaDsTimeUs adsl2LConfProfTargetSnrmDs adsl2LConfProfTargetSnrmUs adsl2LConfProfMaxSnrmDs adsl2LConfProfMaxSnrmUs adsl2LConfProfMinSnrmDs adsl2LConfProfMinSnrmUs adsl2LConfProfMsgMinUs adsl2LConfProfMsgMinDs adsl2LConfProfAtuTransSysEna adsl2LConfProfPmMode adsl2LConfProfL0Time adsl2LConfProfL2Time adsl2LConfProfL2Atpr adsl2LConfProfL2Atprt adsl2LConfProfRowStatus adsl2LConfProfAdslMode adsl2LConfProfMaxNomPsdDs adsl2LConfProfMaxNomPsdUs adsl2LConfProfMaxNomAtpDs adsl2LConfProfMaxNomAtpUs adsl2LConfProfMaxAggRxPwrUs adsl2LConfProfPsdMaskDs adsl2LConfProfPsdMaskUs adsl2LConfProfPsdMaskSelectUs adsl2LConfProfModeSpecRowStatus adsl2ChConfProfProfileName adsl2ChConfProfMinDataRateDs adsl2ChConfProfMinDataRateUs adsl2ChConfProfMinResDataRateDs adsl2ChConfProfMinResDataRateUs adsl2ChConfProfMaxDataRateDs adsl2ChConfProfMaxDataRateUs adsl2ChConfProfMinDataRateLowPwrDs adsl2ChConfProfMaxDelayDs adsl2ChConfProfMaxDelayUs adsl2ChConfProfMinProtectionDs adsl2ChConfProfMinProtectionUs adsl2ChConfProfMaxBerDs adsl2ChConfProfMaxBerUs adsl2ChConfProfUsDataRateDs
ADSL2ConfProfRausNRMDS ADSL2ConfProfRausNRMDS ADSL2ConfProfRasNRMDS ADSL2ConfProfRasNRMDS ADSL2ConfProfRasNRMDS ADSL2ConfProfRasNRMDS ADSL2ConfProfRasNRMUS ADSL2ConfProfRasNRMUS ADSL2ConfProfRasNRMDS ADSL2ConfProfProfRasNRMDS ADSL2ConfProfProfRasNRMDSADSL2ConfProfMsgMinus ADSL2ConfProfMsgMinds ADSL2ConfProfFatTranssysena ADSL2ConfProfPmMode ADSL2ConfProfL0时间ADSL2ConfProfL2时间ADSL2ConfProfL2时间ADSL2ConfProfL2TPR ADSL2ConfProfRowStatus ADSL2ConfProfMode ADSL2ConfProfMaxNompSDS ADSL2ConfProfMaxNompSDS ADSL2ConfProfMaxNompSDU ADSL2ConfProfMaxNomNompDS ADSL2ConfMaxNompDS ADSL2ConfMaxNompDS ADSL2ConfMaxNompSadsl2ConfProfMaxAggrxpwrus adsl2ConfProfProfPsdMaskds adsl2ConfProfPsdMaskus adsl2ConfProfPsdMaskselectus adsl2ConfProfModesSpecRowStatus adsl2chConfProfileName adsl2chConfRofMindDatarates adsl2chConfRofMindDatarates adsl2chConfMinResDatarates adsl2chConfMinResDatarates adsl2chConfMaxDatarates adsl2chConfMindMaxDataratesadsl2ChConfProfMinDataRateLowPwrDs adsl2ChConfProfMaxDelayDs adsl2chconfprofmindayus adsl2chconfprofminprofmin保护adsl2chconfprofmindatarate adsl2ChConfProfMaxBerUs adsl2chconfprofmindayus adsl2chconfprofminprofmin保护adsl2chconfprofminprofminprofminprofmindatarates adsl2chconfprofmind
adsl2ChConfProfDsDataRateDs
adsl2ChConfProfUsDataRateUs
adsl2ChConfProfDsDataRateUs
adsl2ChConfProfImaEnabled
adsl2ChConfProfRowStatus
adsl2LAlarmConfTempTemplateName
adsl2LAlarmConfTempLineProfile
adsl2LAlarmConfTempChan1ConfProfile
adsl2LAlarmConfTempChan2ConfProfile
adsl2LAlarmConfTempChan3ConfProfile
adsl2LAlarmConfTempChan4ConfProfile
adsl2LAlarmConfTempRowStatus
adsl2LineAlarmConfProfileName
adsl2LineAlarmConfProfileAtucThresh15MinFecs
adsl2LineAlarmConfProfileAtucThresh15MinEs
adsl2LineAlarmConfProfileAtucThresh15MinSes
adsl2LineAlarmConfProfileAtucThresh15MinLoss
adsl2LineAlarmConfProfileAtucThresh15MinUas
adsl2LineAlarmConfProfileAturThresh15MinFecs
adsl2LineAlarmConfProfileAturThresh15MinEs
adsl2LineAlarmConfProfileAturThresh15MinSes
adsl2LineAlarmConfProfileAturThresh15MinLoss
adsl2LineAlarmConfProfileAturThresh15MinUas
adsl2LineAlarmConfProfileThresh15MinFailedFullInt
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt
adsl2LineAlarmConfProfileRowStatus
adsl2ChAlarmConfProfileName
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations
adsl2ChAlarmConfProfileAtucThresh15MinCorrected
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations
adsl2ChAlarmConfProfileAturThresh15MinCorrected
adsl2ChAlarmConfProfileRowStatus
adsl2ChConfProfDsDataRateDs
adsl2ChConfProfUsDataRateUs
adsl2ChConfProfDsDataRateUs
adsl2ChConfProfImaEnabled
adsl2ChConfProfRowStatus
adsl2LAlarmConfTempTemplateName
adsl2LAlarmConfTempLineProfile
adsl2LAlarmConfTempChan1ConfProfile
adsl2LAlarmConfTempChan2ConfProfile
adsl2LAlarmConfTempChan3ConfProfile
adsl2LAlarmConfTempChan4ConfProfile
adsl2LAlarmConfTempRowStatus
adsl2LineAlarmConfProfileName
adsl2LineAlarmConfProfileAtucThresh15MinFecs
adsl2LineAlarmConfProfileAtucThresh15MinEs
adsl2LineAlarmConfProfileAtucThresh15MinSes
adsl2LineAlarmConfProfileAtucThresh15MinLoss
adsl2LineAlarmConfProfileAtucThresh15MinUas
adsl2LineAlarmConfProfileAturThresh15MinFecs
adsl2LineAlarmConfProfileAturThresh15MinEs
adsl2LineAlarmConfProfileAturThresh15MinSes
adsl2LineAlarmConfProfileAturThresh15MinLoss
adsl2LineAlarmConfProfileAturThresh15MinUas
adsl2LineAlarmConfProfileThresh15MinFailedFullInt
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt
adsl2LineAlarmConfProfileRowStatus
adsl2ChAlarmConfProfileName
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations
adsl2ChAlarmConfProfileAtucThresh15MinCorrected
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations
adsl2ChAlarmConfProfileAturThresh15MinCorrected
adsl2ChAlarmConfProfileRowStatus
Note also that the interface indices in this MIB are maintained persistently. View-based Access Control Model (VACM) data relating to these SHOULD be stored persistently as well [RFC3410].
还要注意，此MIB中的接口索引是持久维护的。与这些相关的基于视图的访问控制模型（VACM）数据也应持久存储[RFC3410]。
An ADSL/ADSL2 and ADSL2+ Line consists of two units: ATU-C (the central office termination unit) and ATU-R (the remote termination unit). There are up to 4 channels, each carrying an independent information flow, as shown in the figure below.
ADSL/ADSL2和ADSL2+线路由两个单元组成：ATU-C（中央局终端单元）和ATU-R（远程终端单元）。最多有4个通道，每个通道承载独立的信息流，如下图所示。
<-- Network Side Customer Side -->
<-- Network Side Customer Side -->
|<//////////////// ADSL/ADSL2/ADSL2+ Span /////////////////>|
|<//////////////// ADSL/ADSL2/ADSL2+ Span /////////////////>|
+-------+ +-------+
+ |<---------------------1------------------->| +
+ |<---------------------2------------------->| +
| ATU-C <~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~>| ATU-R |
+ |<---------------------3------------------->| +
+ |<---------------------4------------------->| +
+-------+ +-------+
+-------+ +-------+
+ |<---------------------1------------------->| +
+ |<---------------------2------------------->| +
| ATU-C <~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~>| ATU-R |
+ |<---------------------3------------------->| +
+ |<---------------------4------------------->| +
+-------+ +-------+
Key: <////> ADSL/ADSL2/ADSL2+ Span
<~~~~> ADSL/ADSL2/ADSL2+ twisted-pair
-1- Channel #1 carried over the line
-2- Optional channel #2 carried over the line
-3- Optional channel #3 carried over the line
-4- Optional channel #4 carried over the line
Key: <////> ADSL/ADSL2/ADSL2+ Span
<~~~~> ADSL/ADSL2/ADSL2+ twisted-pair
-1- Channel #1 carried over the line
-2- Optional channel #2 carried over the line
-3- Optional channel #3 carried over the line
-4- Optional channel #4 carried over the line
Figure 2: General topology for an ADSL/ADSL2/ADSL2+ Line
Figure 2: General topology for an ADSL/ADSL2/ADSL2+ Line
There are various types of counters specified in this MIB. Each counter refers either to the whole ADSL/ADSL2/ADSL2+ line, to one of the XTU entities, or to one of the bearer channels.
此MIB中指定了各种类型的计数器。每个计数器表示整个ADSL/ADSL2/ADSL2+线路、一个XTU实体或一个承载信道。
o On the whole line level
o 全线
For full initializations, failed full initializations, short initializations, and failed short initializations, there are event counters, current 15-minute and 0 to 96 15-minute history bucket(s) of "interval-counters", as well as current and 0 to 30 previous 1-day interval-counter(s). Each current 15-minute "failed" event bucket has an associated threshold notification.
对于完全初始化、失败的完全初始化、短初始化和失败的短初始化，有事件计数器、“间隔计数器”的当前15分钟和0到96个15分钟历史存储桶，以及当前和0到30个以前的1天间隔计数器。每个当前15分钟“失败”事件存储桶都有一个关联的阈值通知。
o On the XTU level
o 关于XTU级别
For the LOS Seconds, ES, SES, FEC seconds, and UAS, there are event counters, current 15-minute and 0 to 96 15-minute history bucket(s) of "interval-counters", as well as current and 0 to 30 previous 1-day interval-counter(s). Each current 15-minute event bucket has an associated threshold notification.
对于服务水平秒、ES、SES、FEC秒和UAS，有事件计数器、“间隔计数器”的当前15分钟和0至96 15分钟历史数据段，以及当前和0至30前1天间隔计数器。每个当前15分钟事件存储桶都有一个关联的阈值通知。
o On the bearer channel level
o 在承载信道级别上
For the coding violations (CRC anomalies) and corrected blocks (i.e., FEC events), there are event counters, current 15-minute and 0 to 96 15-minute history bucket(s) of "interval-counters", as well as current and 0 to 30 previous 1-day interval-counter(s). Each current 15-minute event bucket has an associated threshold notification.
对于编码违规（CRC异常）和校正块（即FEC事件），有事件计数器、“间隔计数器”的当前15分钟和0至96 15分钟历史存储桶，以及当前和0至30个前1天间隔计数器。每个当前15分钟事件存储桶都有一个关联的阈值通知。
Although it is possible to support up to 96 15-minute history buckets of "interval-counters", systems implementing this MIB module SHOULD practically support at least 16 buckets, as specified in ITU-T G.997.1, paragraph 7.2.7.2.
尽管可以支持多达96个15分钟历史存储桶的“间隔计数器”，但按照ITU-T G.997.1第7.2.7.2段的规定，实现该MIB模块的系统实际上应支持至少16个存储桶。
Similarly, it is possible to support up to 30 previous 1-day "interval-counters", but systems implementing this MIB module SHOULD support at least 1 previous-day bucket.
类似地，最多可以支持30个前一天“间隔计数器”，但实现此MIB模块的系统应至少支持1个前一天存储桶。
There is no requirement for an agent to ensure a fixed relationship between the start of a 15-minute interval and any wall clock; however, some implementations may align the 15-minute intervals with quarter hours. Likewise, an implementation may choose to align one day intervals with the start of a day.
不要求代理人确保15分钟间隔的开始和任何挂钟之间的固定关系；但是，一些实施可能会将15分钟的间隔与四分之一小时的间隔对齐。同样，实现可以选择将一天的间隔与一天的开始对齐。
Counters are not reset when an XTU is reinitialized, only when the agent is reset or reinitialized (or under specific request outside the scope of this MIB module).
当重新初始化XTU时，计数器不会重置，仅当代理重置或重新初始化时（或在该MIB模块范围之外的特定请求下）才会重置。
As in RFC 3593 [RFC3593] and RFC 2662 [RFC2662], in case the data for an interval is suspect or known to be invalid, the agent MUST report the interval as invalid. If the current 15-minute event bucket is determined to be invalid, the element management system SHOULD ignore its content, and the agent MUST NOT generate notifications based upon the value of the event bucket.
如RFC 3593[RFC3593]和RFC 2662[RFC2662]中所述，如果怀疑或已知间隔数据无效，则代理必须将间隔报告为无效。如果确定当前15分钟事件桶无效，元素管理系统应忽略其内容，并且代理不得基于事件桶的值生成通知。
A valid 15-minute event bucket SHOULD usually count the events for exactly 15 minutes. Similarly, a valid 1-day event bucket SHOULD usually count the events for exactly 24 hours. However, the following scenarios are exceptional:
一个有效的15分钟事件存储桶通常应该精确计算15分钟内的事件。类似地，一个有效的1天事件存储桶通常应该精确计算24小时内的事件。但是，以下情况是例外情况：
1) For implementations that align the 15-minute intervals with quarter hours, and the 1-day intervals with start of a day, the management system may still start the PM process not aligned with the wall clock. Such a management system may wish to retrieve even partial information for the first event buckets, rather than declaring them all as invalid.
1) 对于将15分钟的时间间隔与四分之一小时、将一天的时间间隔与一天的开始对齐的实施，管理系统仍可能启动PM流程，而不是与挂钟对齐。这样的管理系统可能希望检索第一个事件存储桶的部分信息，而不是将它们全部声明为无效。
2) For an event bucket that suffered relatively short outages, the management system may wish to retrieve the available PM outcomes, rather than declare the whole event bucket as invalid. This is more important for 1-day event buckets.
2) 对于中断时间相对较短的事件存储桶，管理系统可能希望检索可用的PM结果，而不是将整个事件存储桶声明为无效。这对于为期一天的活动更为重要。
3) An event bucket may be shorter or longer than the formal duration if a clock adjustment was performed during the interval.
3) 如果在间隔期间执行时钟调整，则事件桶可能比正式持续时间短或长。
This MIB allows supporting the exceptional scenarios described above by reporting the actual Monitoring Time of a monitoring interval. This parameter is relevant only for Valid intervals, but is useful for these exceptional scenarios:
此MIB允许通过报告监控间隔的实际监控时间来支持上述异常场景。此参数仅与有效间隔相关，但对于以下例外情况有用：
a) The management system MAY still declare a partial PM interval as Valid and report the actual number of seconds the interval lasted.
a) 管理系统仍然可以声明部分PM间隔有效，并报告间隔持续的实际秒数。
b) If the interval was shortened or extended due to clock corrections, the management system SHOULD report the actual number of seconds the interval lasted, besides reporting that the interval is Valid.
b) 如果间隔因时钟校正而缩短或延长，管理系统除了报告间隔有效外，还应报告间隔持续的实际秒数。
As a managed node can handle a large number of XTUs, (e.g., hundreds or perhaps thousands of lines), provisioning every parameter on every XTU may become burdensome. Moreover, most lines are provisioned identically with the same set of parameters. To simplify the provisioning process, this MIB module makes use of profiles and templates.
由于受管节点可以处理大量的XTU（例如，数百行或数千行），在每个XTU上配置每个参数可能会变得很麻烦。此外，大多数行使用相同的参数集进行相同的设置。为了简化资源调配过程，此MIB模块使用配置文件和模板。
A configuration profile is a set of parameters that can be shared by multiple entities. There are configuration profiles to address the line-level provisioning, and another type of profile that addresses the channel-level provisioning parameters.
配置概要文件是一组可由多个实体共享的参数。有用于处理线路级供应的配置配置文件，还有另一种类型的配置文件用于处理通道级供应参数。
A configuration template is actually a profile-of-profiles. That is, a template is comprised of one line configuration profile and one or more channel configuration profiles. A template provides the complete configuration of a line. The same configuration can be shared by multiple lines.
配置模板实际上是配置文件的配置文件。也就是说，模板由一个线路配置文件和一个或多个信道配置文件组成。模板提供线路的完整配置。同一配置可由多条线路共享。
Similarly to the configuration profiles and templates, this MIB module makes use of templates and profiles for specifying the alarm thresholds associated with performance parameters. This allows provisioning multiple lines with the same criteria for generating threshold crossing notifications.
与配置配置文件和模板类似，此MIB模块使用模板和配置文件指定与性能参数关联的报警阈值。这允许设置具有相同条件的多行以生成阈值跨越通知。
The following paragraphs describe templates and profiles used in this MIB module
以下段落描述此MIB模块中使用的模板和配置文件
o Line Configuration Profiles - Line configuration profiles contain parameters for configuring the low layer of ADSL/ADSL2 and ADSL2+ lines. They are defined in the adsl2LineConfProfTable.
o 线路配置配置文件-线路配置文件包含用于配置低层ADSL/ADSL2和ADSL2+线路的参数。它们在adsl2LineConfProfTable中定义。
The line configuration includes issues such as the specific ADSL/ADSL2 or ADSL2+ modes to enable on the respective line, power spectrum parameters, rate adaptation criteria, and SNR margin-related parameters. A subset of the line configuration parameters depends upon the specific ADSL Mode allowed (i.e., Does the profile allow ADSL, ADSL2, and/or ADSL2+) as well as what annex/annexes of the standard are allowed. This is the reason a line profile MUST include one or more mode-specific extensions.
线路配置包括诸如在各自线路上启用的特定ADSL/ADSL2或ADSL2+模式、功率谱参数、速率自适应标准和SNR裕度相关参数等问题。线路配置参数的子集取决于允许的特定ADSL模式（即，配置文件是否允许ADSL、ADSL2和/或ADSL2+）以及允许的标准附件。这就是线路配置文件必须包含一个或多个特定于模式的扩展名的原因。
o Channel Configuration Profiles - Channel configuration profiles contain parameters for configuring bearer channels over the ADSL/ADSL2 and ADSL2+ lines. They are sometimes considered the service layer configuration of the ADSL/ADSL2 and ADSL2+ lines. They are defined in the adsl2ChConfProfTable.
o 信道配置配置文件-信道配置文件包含用于在ADSL/ADSL2和ADSL2+线路上配置承载信道的参数。它们有时被认为是ADSL/ADSL2和ADSL2+线路的服务层配置。它们在ADSL2CHCONFPROFF表中定义。
The channel configuration includes issues such as the desired minimum and maximum rate on each traffic flow direction and impulse noise protection parameters.
信道配置包括诸如每个交通流方向上的期望最小和最大速率以及脉冲噪声保护参数等问题。
o Line Configuration Templates - Line configuration templates allow combining line configuration profiles and channel configuration profiles to a comprehensive configuration of the ADSL/ADSL2 and ADSL2+ line. They are defined in the adsl2LineConfTemplateTable.
o 线路配置模板-线路配置模板允许将线路配置配置文件和信道配置文件组合到ADSL/ADSL2和ADSL2+线路的综合配置中。它们在adsl2LineConfTemplateTable中定义。
The line configuration template includes one index (OID) of a line configuration profile and one to four indexes of channel configuration profiles. The template also addresses the issue of distributing the excess available data rate on each traffic flow direction (i.e., the data rate left after each channel is allocated a data rate to satisfy its minimum requested data rate) among the various channels.
线路配置模板包括线路配置配置文件的一个索引（OID）和通道配置配置文件的一到四个索引。该模板还解决了在各个信道之间分配每个交通流方向上的多余可用数据速率（即，在每个信道分配数据速率以满足其最小请求数据速率之后剩余的数据速率）的问题。
o Line Alarm Configuration Profiles - Line-level Alarm configuration profiles contain the threshold values for Performance Monitoring (PM) parameters, counted either on the whole line level or on an XTU level. Thresholds are required only for failures and anomalies, e.g., there are thresholds for failed initializations and LOS seconds, but not for the aggregate number of full initializations. These profiles are defined in the adsl2LineAlarmConfProfileTable.
o 线路报警配置配置文件-线路级报警配置文件包含性能监控（PM）参数的阈值，在整个线路级或XTU级上计算。仅在故障和异常情况下才需要阈值，例如，存在初始化失败和服务水平秒的阈值，但不存在完全初始化总数的阈值。这些配置文件在ADSL2LineAlarmConfProfile表中定义。
o Channel Alarm Configuration Profiles - Channel-level Alarm configuration profiles contain the threshold values for PM parameters counted on a bearer channel level. Thresholds are defined for two types of anomalies: corrected blocks and coding violations. These profiles are defined in the adsl2ChAlarmConfProfileTable.
o 信道报警配置配置文件-信道级报警配置文件包含在承载信道级上计数的PM参数的阈值。为两种类型的异常定义了阈值：校正块和编码冲突。这些配置文件在ADSL2CHAlarmConfProfile表中定义。
o Line Alarm Configuration Templates - Line Alarm configuration templates allow combining line-level alarm configuration profiles and channel-level alarm configuration profiles to a comprehensive configuration of the PM thresholds for ADSL/ADSL2 and ADSL2+ line. They are defined in the adsl2LineAlarmConfTemplateTable.
o 线路报警配置模板-线路报警配置模板允许将线路级报警配置配置文件和信道级报警配置文件组合到ADSL/ADSL2和ADSL2+线路PM阈值的综合配置中。它们在adsl2LineAlarmConfTemplateTable中定义。
The line alarm configuration template includes one index (OID) of a line-level alarm configuration profile and one to four indexes of channel-level alarm configuration profiles.
线路报警配置模板包括线路级报警配置配置文件的一个索引（OID）和通道级报警配置文件的一到四个索引。
The index value for each profile and template is a locally-unique, administratively assigned name having the textual convention 'SnmpAdminString' (RFC 3411 [RFC3411]).
每个概要文件和模板的索引值都是本地唯一的、管理分配的名称，具有文本约定“SnmpAdminString”（RFC 3411[RFC3411]）。
One or more lines may be configured to share parameters of a single configuration template (e.g., adsl2LConfTempTemplateName = 'silver') by setting its adsl2LineCnfgTemplate objects to the value of this template.
通过将其ADSL2LINECNFGTAMPLATE对象设置为此模板的值，可以将一条或多条线路配置为共享单个配置模板的参数（例如，ADSL2LConfTemplateName='silver'）。
One or more lines may be configured to share parameters of a single Alarm configuration template (e.g., adsl2LAlarmConfTempTemplateName = 'silver') by setting its adsl2LineAlarmCnfgTemplate objects to the value of this template.
通过将其ADSL2LINEARMCNFGTEMPLATE对象设置为该模板的值，可以将一条或多条线路配置为共享单个报警配置模板的参数（例如，ADSL2LARMCONFTEMPLATENAME='silver'）。
Before a template can be deleted or taken out of service, it MUST first be unreferenced from all associated lines. Implementations MAY also reject template modification while it is associated with any line.
在删除模板或使其停止使用之前，必须先从所有关联行取消引用模板。当模板修改与任何行关联时，实现也可能拒绝模板修改。
Before a profile can be deleted or taken out of service, it MUST first be unreferenced from all associated templates. Implementations MAY also reject profile modification while it is referenced by any template.
在删除或停用配置文件之前，必须先从所有关联模板中取消引用该配置文件。在任何模板引用概要文件时，实现也可能拒绝概要文件修改。
Implementations MUST provide a default profile whose name is 'DEFVAL' for each profile and template type. The values of the associated parameters will be vendor-specific unless otherwise indicated in this document. Before a line's templates have been set, these templates will be automatically used by setting adsl2LineCnfgTemplate and adsl2LineAlarmCnfgTemplate to 'DEFVAL' where appropriate. This default profile name, 'DEFVAL', is considered reserved in the context of profiles and templates defined in this MIB module.
实现必须为每个配置文件和模板类型提供一个名为“deffal”的默认配置文件。除非本文件另有说明，否则相关参数的值将根据供应商而定。在设置线路模板之前，通过将ADSL2LINECNFGMETABLE和ADSL2LINEARMCNFGTEMPLATE设置为“DEFVAL”（如适用），将自动使用这些模板。此默认配置文件名“deffal”在该MIB模块中定义的配置文件和模板上下文中被视为保留。
Profiles and templates are created, assigned, and deleted dynamically using the profile name and profile row status in each of the profile tables.
使用每个配置文件表中的配置文件名称和配置文件行状态动态创建、分配和删除配置文件和模板。
If the implementation allows modifying a profile or template while it is associated with a line, then such changes MUST take effect immediately. These changes MAY result in a restart (hard reset or soft restart) of the units on the line.
如果实现允许在与行关联时修改概要文件或模板，则此类更改必须立即生效。这些更改可能会导致机组重新启动（硬复位或软重启）。
The number of bearer channels is configured by setting the template attributes adsl2LConfTempChan1ConfProfile, adsl2LConfTempChan2ConfProfile, adsl2LConfTempChan3ConfProfile, and adsl2LConfTempChan4ConfProfile and then assigning that template to a DSL line using the adsl2LineCnfgTemplate attribute. When the number of bearer channels for a DSL line changes, the SNMP agent will automatically create or destroy rows in channel-related tables associated with that line. For example, when a DSL line is operating with one bearer channel, there will be zero rows in channel-related tables for channels two, three, and four. The SNMP agent MUST create and destroy channel-related rows as follows:
通过设置模板属性adsl2LConfTempChan1ConfProfile、adsl2LConfTempChan2ConfProfile、adsl2LConfTempChan3ConfProfile和adsl2LConfTempChan4ConfProfile，然后使用ADSL2LINECNfTemplate属性将该模板分配给DSL线路，可以配置承载信道的数量。当DSL线路的承载信道数发生变化时，SNMP代理将自动在与该线路相关联的信道相关表中创建或销毁行。例如，当DSL线路使用一个承载信道运行时，信道2、3和4的信道相关表中将有零行。SNMP代理必须创建和销毁与通道相关的行，如下所示：
o When the number of bearer channels for a DSL line changes to a higher number, the SNMP agent will automatically create rows in the adsl2ChannelStatusTable, and adsl2PMChCurrTable tables for that line.
o 当DSL线路的承载信道数更改为更大的数目时，SNMP代理将自动在ADSL2CHANNEL STATUSSTABLE和adsl2PMChCurrTable表中为该线路创建行。
o When the number of bearer channels for a DSL line changes to a lower number, the SNMP agent will automatically destroy rows in the adsl2ChannelStatusTable, adsl2PMChCurrTable, adsl2PMChHist15MinTable, and adsl2PMChHist1DTable tables for that line.
o 当DSL线路的承载信道数更改为较低的数目时，SNMP代理将自动销毁该线路的ADSL2channelStatus表、adsl2PMChCurrTable表、adsl2PMChHist15MinTable表和adsl2PMChHist1DTable表中的行。
The ability to generate the SNMP notifications coldStart/warmStart (per [RFC3418]), which are per agent (e.g., per Digital Subscriber Line Access Multiplexer, or DSLAM, in such a device), and linkUp/linkDown (per [RFC2863]), which are per interface (i.e., ADSL/ADSL2 or ADSL2+ line), is REQUIRED.
需要能够生成每个代理的SNMP通知coldStart/warmStart（per[RFC3418]）（例如，在这样的设备中，每个数字用户线路接入多路复用器或DSLAM）和每个接口（即ADSL/ADSL2或ADSL2+线路）的链路上/链路下（per[RFC2863]）。
A linkDown notification MAY be generated whenever any of ES, SES, CRC Anomaly, LOS, LOF, or UAS event occurs. The corresponding linkUp notification MAY be sent when all link failure conditions are cleared.
无论何时发生ES、SES、CRC异常、LOS、LOF或UAS事件，都可能生成链路关闭通知。当清除所有链路故障条件时，可能会发送相应的连接通知。
The notifications defined in this MIB module are for status change (e.g., initialization failure) and for the threshold crossings associated with the following events: full initialization failures, short initialization failures, ES, SES, FEC Seconds, LOS Seconds, UAS, FEC Seconds, FEC events, and CRC anomalies. Each threshold has its own enable/threshold value. When that value is 0, the notification is disabled.
此MIB模块中定义的通知用于状态更改（例如初始化失败）和与以下事件相关的阈值交叉：完全初始化失败、短初始化失败、ES、SES、FEC秒、LOS秒、UAS、FEC秒、FEC事件和CRC异常。每个阈值都有自己的启用/阈值。当该值为0时，将禁用通知。
The adsl2LineStatusAtur and adsl2LineStatusAtuc are bitmasks representing all outstanding error conditions associated with the ATU-R and ATU-C (respectively). Note that since the ATU-R status is obtained via the EOC, this information may be unavailable in case the ATU-R is unreachable via EOC during a line error condition. Therefore, not all conditions may always be included in its current status. Notifications corresponding to the bit fields in those two status objects are defined.
ADSL2LINESTAUSATUR和ADSL2LINESTAUSATUC是位掩码，分别表示与ATU-R和ATU-C相关的所有未解决错误条件。请注意，由于ATU-R状态是通过EOC获得的，因此如果在线路错误情况下无法通过EOC访问ATU-R，则此信息可能不可用。因此，并非所有条件都可以始终包含在其当前状态中。定义了与这两个状态对象中的位字段相对应的通知。
Note that there are other status parameters that refer to the ATU-R (e.g., downstream line attenuation). Those parameters also depend on the availability of EOC between the ATU-C and the ATU-R.
请注意，还有其他状态参数涉及ATU-R（例如，下游线路衰减）。这些参数还取决于ATU-C和ATU-R之间EOC的可用性。
A threshold notification occurs whenever the corresponding current 15-minute interval error counter becomes equal to or exceeds the threshold value. Only one notification SHOULD be sent per interval per interface. Since the current 15-minute counter is reset to 0 every 15 minutes, if the condition persists, the notification may recur as often as every 15 minutes. For example, to get a notification whenever a "loss of" event occurs (but at most once every 15 minutes), set the corresponding threshold to 1. The agent will generate a notification when the event originally occurs.
每当相应的当前15分钟间隔错误计数器等于或超过阈值时，就会出现阈值通知。每个接口的每个间隔只能发送一个通知。由于当前15分钟计数器每15分钟重置一次为0，因此如果该情况持续存在，则该通知可能每15分钟重复一次。例如，要在“丢失”事件发生时（但最多每15分钟一次）获取通知，请将相应的阈值设置为1。代理将在事件最初发生时生成通知。
Notifications, other than the threshold notifications listed above, SHOULD be rate-limited (throttled) such that there is an implementation-specific gap between the generation of consecutive notifications of the same event. When notifications are rate-
除了上面列出的阈值通知之外，其他通知都应该是速率限制（限制）的，以便在生成同一事件的连续通知之间存在特定于实现的间隔。当通知被删除时，费率为-
limited, they are dropped and not queued for sending at a future time. This is intended to be a general rate-limiting statement for notifications that otherwise have no explicit rate-limiting assertions in this document.
有限，它们会被丢弃，并且不会排队等待将来发送。对于本文档中没有明确速率限制断言的通知，这是一个通用的速率限制声明。
Note that the Network Management System, or NMS, may receive a linkDown notification, as well, if enabled (via ifLinkUpDownTrapEnable [RFC2863]). At the beginning of the next 15 minute interval, the counter is reset. When the first second goes by and the event occurs, the current interval bucket will be 1, which equals the threshold, and the notification will be sent again.
请注意，如果启用，网络管理系统（或NMS）也可能会收到链路关闭通知（通过iFlinkUpDownTrappenable[RFC2863]）。在下一个15分钟间隔开始时，计数器复位。当第一秒过去并且事件发生时，当前间隔bucket将为1（等于阈值），并且将再次发送通知。
ADSL2-LINE-TC-MIB DEFINITIONS ::= BEGIN
ADSL2-LINE-TC-MIB DEFINITIONS ::= BEGIN
IMPORTS MODULE-IDENTITY, transmission FROM SNMPv2-SMI
从SNMPv2 SMI导入模块标识和传输
TEXTUAL-CONVENTION FROM SNMPv2-TC;
来自SNMPv2 TC的文本约定；
adsl2TCMIB MODULE-IDENTITY
LAST-UPDATED "200610040000Z" -- October 4th, 2006
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
adsl2TCMIB MODULE-IDENTITY
LAST-UPDATED "200610040000Z" -- October 4th, 2006
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed Sand Channel Systems Postal: P.O. Box 37324 Raleigh NC 27627-732 Email: sneedmike@hotmail.com Phone: +1 206 600 7022
主席：Mike Sneed Sand Channel Systems邮政：北卡罗来纳州罗利市37324信箱27627-732电子邮件：sneedmike@hotmail.com电话：+1206600722
Co-Chair & Co-editor: Menachem Dodge ECI Telecom Ltd. Postal: 30 Hasivim St. Petach Tikva 49517, Israel. Email: mbdodge@ieee.org Phone: +972 3 926 8421
共同主席和共同编辑：Menahem Dodge ECI Telecom Ltd.邮政编码：30 Hasivim St.Petach Tikva 49517，以色列。电邮：mbdodge@ieee.org电话：+97239268421
Co-editor: Moti Morgenstern ECI Telecom Ltd. Postal: 30 Hasivim St. Petach Tikva 49517, Israel. Email: moti.morgenstern@ecitele.com Phone: +972 3 926 6258
共同编辑：Moti Morgenstern ECI电信有限公司，邮政编码：30 Hasivim St.Petach Tikva 49517，以色列。电子邮件：moti。morgenstern@ecitele.com电话：+9723926658
Co-editor: Scott Baillie NEC Australia Postal: 649-655 Springvale Road, Mulgrave, Victoria 3170, Australia. Email: scott.baillie@nec.com.au Phone: +61 3 9264 3986
合编：Scott Baillie NEC澳大利亚邮政：澳大利亚维多利亚州马尔格雷夫市斯普林维尔路649-655号，邮编3170。电子邮件：斯科特。baillie@nec.com.au电话：+61 3 9264 3986
Co-editor: Umberto Bonollo NEC Australia Postal: 649-655 Springvale Road, Mulgrave, Victoria 3170, Australia. Email: umberto.bonollo@nec.com.au Phone: +61 3 9264 3385 " DESCRIPTION "This MIB Module provides Textual Conventions to be used by the ADSL2-LINE-MIB module for the purpose of managing ADSL, ADSL2, and ADSL2+ lines.
合编：Umberto Bonollo NEC澳大利亚邮政：澳大利亚维多利亚州马尔格雷夫市斯普林维尔路649-655号，邮编：3170。电邮：umberto。bonollo@nec.com.au电话：+61 3 9264 3385“说明”此MIB模块提供ADSL2-LINE-MIB模块用于管理ADSL、ADSL2和ADSL2+线路的文本约定。
Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4706: see the RFC itself for full legal notices."
版权所有（C）互联网协会（2006年）。此MIB模块的此版本是RFC 4706的一部分：有关完整的法律通知，请参阅RFC本身。”
REVISION "200610040000Z" -- October 4th, 2006
DESCRIPTION "Initial version, published as RFC 4706."
::= { transmission 238 2 } -- adsl2MIB 2
REVISION "200610040000Z" -- October 4th, 2006
DESCRIPTION "Initial version, published as RFC 4706."
::= { transmission 238 2 } -- adsl2MIB 2
------------------------------------------------
-- Textual Conventions --
------------------------------------------------
------------------------------------------------
-- Textual Conventions --
------------------------------------------------
Adsl2Unit ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies a transceiver as being either an ATU-C or
an ATU-R. An ADSL line consists of two transceivers, an ATU-C
and an ATU-R. Attributes with this syntax reference the two
sides of a line. Specified as an INTEGER, the two values
Adsl2Unit ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies a transceiver as being either an ATU-C or
an ATU-R. An ADSL line consists of two transceivers, an ATU-C
and an ATU-R. Attributes with this syntax reference the two
sides of a line. Specified as an INTEGER, the two values
are:
是：
atuc(1) -- Central office ADSL terminal unit (ATU-C).
atur(2) -- Remote ADSL terminal unit (ATU-R)."
SYNTAX INTEGER {
atuc(1),
atur(2)
}
atuc(1) -- Central office ADSL terminal unit (ATU-C).
atur(2) -- Remote ADSL terminal unit (ATU-R)."
SYNTAX INTEGER {
atuc(1),
atur(2)
}
Adsl2Direction ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies the direction of a band as being
either upstream or downstream. Specified as an INTEGER,
the two values are:
upstream(1), and
downstream(2)."
SYNTAX INTEGER {
upstream(1),
downstream(2)
}
Adsl2Direction ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies the direction of a band as being
either upstream or downstream. Specified as an INTEGER,
the two values are:
upstream(1), and
downstream(2)."
SYNTAX INTEGER {
upstream(1),
downstream(2)
}
Adsl2TransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A set of ADSL2 line transmission modes, with one bit
per mode. The notes (F) and (L) denote Full-Rate
and Lite/splitterless, respectively:
Bit 00 : Regional Std. (ANSI T1.413) (F)
Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
Bit 02 : G.992.1 POTS non-overlapped (F)
Bit 03 : G.992.1 POTS overlapped (F)
Bit 04 : G.992.1 ISDN non-overlapped (F)
Bit 05 : G.992.1 ISDN overlapped (F)
Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
Bit 07 : G.992.1 TCM-ISDN overlapped (F)
Bit 08 : G.992.2 POTS non-overlapped (L)
Bit 09 : G.992.2 POTS overlapped (L)
Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
Bit 12 : G.992.1 TCM-ISDN symmetric (F) -- not in G.997.1
Bit 13-17: Reserved
Bit 18 : G.992.3 POTS non-overlapped (F)
Bit 19 : G.992.3 POTS overlapped (F)
Bit 20 : G.992.3 ISDN non-overlapped (F)
Bit 21 : G.992.3 ISDN overlapped (F)
Adsl2TransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A set of ADSL2 line transmission modes, with one bit
per mode. The notes (F) and (L) denote Full-Rate
and Lite/splitterless, respectively:
Bit 00 : Regional Std. (ANSI T1.413) (F)
Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
Bit 02 : G.992.1 POTS non-overlapped (F)
Bit 03 : G.992.1 POTS overlapped (F)
Bit 04 : G.992.1 ISDN non-overlapped (F)
Bit 05 : G.992.1 ISDN overlapped (F)
Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
Bit 07 : G.992.1 TCM-ISDN overlapped (F)
Bit 08 : G.992.2 POTS non-overlapped (L)
Bit 09 : G.992.2 POTS overlapped (L)
Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
Bit 12 : G.992.1 TCM-ISDN symmetric (F) -- not in G.997.1
Bit 13-17: Reserved
Bit 18 : G.992.3 POTS non-overlapped (F)
Bit 19 : G.992.3 POTS overlapped (F)
Bit 20 : G.992.3 ISDN non-overlapped (F)
Bit 21 : G.992.3 ISDN overlapped (F)
Bit 22-23: Reserved Bit 24 : G.992.4 POTS non-overlapped (L) Bit 25 : G.992.4 POTS overlapped (L) Bit 26-27: Reserved Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F) Bit 29 : G.992.3 Annex I All-Digital overlapped (F) Bit 30 : G.992.3 Annex J All-Digital non-overlapped (F) Bit 31 : G.992.3 Annex J All-Digital overlapped (F) Bit 32 : G.992.4 Annex I All-Digital non-overlapped (L) Bit 33 : G.992.4 Annex I All-Digital overlapped (L) Bit 34 : G.992.3 Annex L POTS non-overlapped, mode 1, wide U/S (F) Bit 35 : G.992.3 Annex L POTS non-overlapped, mode 2, narrow U/S(F) Bit 36 : G.992.3 Annex L POTS overlapped, mode 3, wide U/S (F) Bit 37 : G.992.3 Annex L POTS overlapped, mode 4, narrow U/S (F) Bit 38 : G.992.3 Annex M POTS non-overlapped (F) Bit 39 : G.992.3 Annex M POTS overlapped (F) Bit 40 : G.992.5 POTS non-overlapped (F) Bit 41 : G.992.5 POTS overlapped (F) Bit 42 : G.992.5 ISDN non-overlapped (F) Bit 43 : G.992.5 ISDN overlapped (F) Bit 44-45: Reserved Bit 46 : G.992.5 Annex I All-Digital non-overlapped (F) Bit 47 : G.992.5 Annex I All-Digital overlapped (F) Bit 48 : G.992.5 Annex J All-Digital non-overlapped (F) Bit 49 : G.992.5 Annex J All-Digital overlapped (F) Bit 50 : G.992.5 Annex M POTS non-overlapped (F) Bit 51 : G.992.5 Annex M POTS overlapped (F) Bit 52-55: Reserved" SYNTAX BITS { ansit1413(0), etsi(1), g9921PotsNonOverlapped(2), g9921PotsOverlapped(3), g9921IsdnNonOverlapped(4), g9921isdnOverlapped(5), g9921tcmIsdnNonOverlapped(6), g9921tcmIsdnOverlapped(7), g9922potsNonOverlapped(8), g9922potsOverlapped(9), g9922tcmIsdnNonOverlapped(10), g9922tcmIsdnOverlapped(11), g9921tcmIsdnSymmetric(12), reserved1(13), reserved2(14),
位22-23：保留位24:G.992.4盆非重叠（L）位25:G.992.4盆重叠（L）位26-27：保留位28:G.992.3附件一全数字非重叠（F）位29:G.992.3附件一全数字重叠（F）位30:G.992.3附件J全数字非重叠（F）位31:G.992.3附件J全数字重叠（F）第32位：G.992.4附件一全数字不重叠（L）第33位：G.992.4附件一全数字重叠（L）第34位：G.992.3附件L盆不重叠，模式1，宽U/S（F）第35位：G.992.3附件L盆不重叠，模式2，窄U/S（F）第36位：G.992.3附件L盆重叠，模式3，宽U/S（F）第37位：G.992.3附件L盆重叠，模式4，窄U/S（F）位38:G.992.3附件M POTS非重叠（F）位39:G.992.3附件M POTS重叠（F）位40:G.992.5 POTS非重叠（F）位41:G.992.5 POTS重叠（F）位42:G.992.5 ISDN非重叠（F）位43:G.992.5 ISDN重叠（F）位44-45：保留位46:G.992.5附件I全数字非重叠（F）第47位：G.992.5附件I全数字重叠（F）第48位：G.992.5附件J全数字非重叠（F）第49位：G.992.5附件J全数字重叠（F）第50位：G.992.5附件M POTS非重叠（F）第51位：G.992.5附件M POTS重叠（F）第52-55位：保留“语法位{ansit1413（0）、etsi（1）、G9921POTSNOVERLAPPED（2），g9921tcmIsdnNonOverlapped（3），g9921tcmIsdnNonOverlapped（4），g9921tcmIsdnNonOverlapped（5），g9921tcmIsdnNonOverlapped（6），g9921tcmIsdnOverlapped（7），g9922tcmIsdnNonOverlapped（8），g9922tcmIsdnNonOverlapped（9），g9922tcmIsdnNonOverlapped（11），G9921Tcmisdn（12），reserved1（13），reserved2（14），
reserved3(15), reserved4(16), reserved5(17), g9923PotsNonOverlapped(18), g9923PotsOverlapped(19), g9923IsdnNonOverlapped(20), g9923isdnOverlapped(21), reserved6(22), reserved7(23), g9924potsNonOverlapped(24), g9924potsOverlapped(25), reserved8(26), reserved9(27), g9923AnnexIAllDigNonOverlapped(28), g9923AnnexIAllDigOverlapped(29), g9923AnnexJAllDigNonOverlapped(30), g9923AnnexJAllDigOverlapped(31), g9924AnnexIAllDigNonOverlapped(32), g9924AnnexIAllDigOverlapped(33), g9923AnnexLMode1NonOverlapped(34), g9923AnnexLMode2NonOverlapped(35), g9923AnnexLMode3Overlapped(36), g9923AnnexLMode4Overlapped(37), g9923AnnexMPotsNonOverlapped(38), g9923AnnexMPotsOverlapped(39), g9925PotsNonOverlapped(40), g9925PotsOverlapped(41), g9925IsdnNonOverlapped(42), g9925isdnOverlapped(43), reserved10(44), reserved11(45), g9925AnnexIAllDigNonOverlapped(46), g9925AnnexIAllDigOverlapped(47), g9925AnnexJAllDigNonOverlapped(48), g9925AnnexJAllDigOverlapped(49), g9925AnnexMPotsNonOverlapped(50), g9925AnnexMPotsOverlapped(51), reserved12(52), reserved13(53), reserved14(54), reserved15(55) }
储备3（15）、储备4（16）、储备5（17）、G9923石油天然气储量（18）、G9923石油天然气储量（19）、G9923石油天然气储量（20）、G9923石油天然气储量（21）、储备6（22）、储备7（23）、G9924石油天然气储量（24）、G9924石油天然气储量（25）、储备8（26）、储备9（27）、G9923石油天然气储量（28）、G9923石油天然气储量（29），G9923附录D（30）、G9923附录D（31）、G9924附录D（32）、G9924附录D（33）、G9923附录模型1不重叠（34）、G9923附录模型2不重叠（35）、G9923附录模型3重叠（36）、G9923附录模型4重叠（37）、G9923附录模型不重叠（38）、G9923附录模型重叠（39），G9925PotsNovellapped（40）、G9925PotsOvellapped（41）、G9925Isdnonoverlapped（42）、g9925isdnOverlapped（43）、reserved10（44）、reserved11（45）、g9925AnnexIAllDigNonOverlapped（46）、G9925Annexialldigonoverlapped（47）、G9925Annexjalldinogonoverlapped（48）、g9925AnnexJAllDigOverlapped（49）、G9925Annexempotsnonoverlapped（50）、G9925AnnexampotsOverlapped（51），保留12（52）、保留13（53）、保留14（54）、保留15（55）}
Adsl2RaMode ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Specifies the rate adaptation behavior for the line.
The three possible behaviors are:
Adsl2RaMode ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Specifies the rate adaptation behavior for the line.
The three possible behaviors are:
manual(1) - No Rate-Adaptation. The initialization
process attempts to synchronize to a
specified rate.
raInit(2) - Rate-Adaptation during initialization process
only, which attempts to synchronize to a rate
between minimum and maximum specified values.
dynamicRa(3) - Dynamic Rate-Adaptation during initialization
process as well as during SHOWTIME."
SYNTAX INTEGER {
manual(1),
raInit(2),
dynamicRa(3)
}
manual(1) - No Rate-Adaptation. The initialization
process attempts to synchronize to a
specified rate.
raInit(2) - Rate-Adaptation during initialization process
only, which attempts to synchronize to a rate
between minimum and maximum specified values.
dynamicRa(3) - Dynamic Rate-Adaptation during initialization
process as well as during SHOWTIME."
SYNTAX INTEGER {
manual(1),
raInit(2),
dynamicRa(3)
}
Adsl2InitResult ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Specifies the result of a full initialization attempt; the
six possible result values are:
noFail(0) - Successful initialization.
configError(1) - Configuration failure.
configNotFeasible(2) - Configuration details not supported.
commFail(3) - Communication failure.
noPeerAtu(4) - Peer ATU not detected.
otherCause(5) - Other initialization failure reason.
Adsl2InitResult ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Specifies the result of a full initialization attempt; the
six possible result values are:
noFail(0) - Successful initialization.
configError(1) - Configuration failure.
configNotFeasible(2) - Configuration details not supported.
commFail(3) - Communication failure.
noPeerAtu(4) - Peer ATU not detected.
otherCause(5) - Other initialization failure reason.
The values used are as defined in ITU-T G.997.1, paragraph 7.5.1.3"
使用的值如ITU-T G.997.1第7.5.1.3.段所定义
SYNTAX INTEGER {
noFail(0),
configError(1),
configNotFeasible(2),
commFail(3),
noPeerAtu(4),
otherCause(5)
}
SYNTAX INTEGER {
noFail(0),
configError(1),
configNotFeasible(2),
commFail(3),
noPeerAtu(4),
otherCause(5)
}
Adsl2OperationModes ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The ADSL2 management model specified includes an ADSL Mode
attribute that identifies an instance of ADSL Mode-Specific
PSD Configuration object in the ADSL Line Profile. The
following classes of ADSL operating mode are defined.
The notes (F) and (L) denote Full-Rate and Lite/splitterless
respectively:
Adsl2OperationModes ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The ADSL2 management model specified includes an ADSL Mode
attribute that identifies an instance of ADSL Mode-Specific
PSD Configuration object in the ADSL Line Profile. The
following classes of ADSL operating mode are defined.
The notes (F) and (L) denote Full-Rate and Lite/splitterless
respectively:
+-------+--------------------------------------------------+
| Value | ADSL operation mode description |
+-------+--------------------------------------------------+
+-------+--------------------------------------------------+
| Value | ADSL operation mode description |
+-------+--------------------------------------------------+
1 - The default/generic PSD configuration. Default configuration will be used when no other matching mode-specific configuration can be found. 2 - ADSL family. The attributes included in the Mode-Specific PSD Configuration are irrelevant for ITU-T G.992.1 and G.992.2 ADSL modes. Hence, it is possible to map those modes to this generic class. 3-7 - Unused. Reserved for future ITU-T specification. 8 - G.992.3 POTS non-overlapped (F) 9 - G.992.3 POTS overlapped (F) 10 - G.992.3 ISDN non-overlapped (F) 11 - G.992.3 ISDN overlapped (F) 12-13 - Unused. Reserved for future ITU-T specification. 14 - G.992.4 POTS non-overlapped (L) 15 - G.992.4 POTS overlapped (L) 16-17 - Unused. Reserved for future ITU-T specification. 18 - G.992.3 Annex I All-Digital non-overlapped (F) 19 - G.992.3 Annex I All-Digital overlapped (F) 20 - G.992.3 Annex J All-Digital non-overlapped (F) 21 - G.992.3 Annex J All-Digital overlapped (F) 22 - G.992.4 Annex I All-Digital non-overlapped (L) 23 - G.992.4 Annex I All-Digital overlapped (L) 24 - G.992.3 Annex L POTS non-overlapped, mode 1, wide U/S (F) 25 - G.992.3 Annex L POTS non-overlapped, mode 2, narrow U/S(F) 26 - G.992.3 Annex L POTS overlapped, mode 3, wide U/S (F) 27 - G.992.3 Annex L POTS overlapped, mode 4, narrow U/S (F) 28 - G.992.3 Annex M POTS non-overlapped (F) 29 - G.992.3 Annex M POTS overlapped (F) 30 - G.992.5 POTS non-overlapped (F) 31 - G.992.5 POTS overlapped (F) 32 - G.992.5 ISDN non-overlapped (F) 33 - G.992.5 ISDN overlapped (F) 34-35 - Unused. Reserved for future ITU-T specification. 36 - G.992.5 Annex I All-Digital non-overlapped (F) 37 - G.992.5 Annex I All-Digital overlapped (F) 38 - G.992.5 Annex J All-Digital non-overlapped (F) 39 - G.992.5 Annex J All-Digital overlapped (F) 40 - G.992.5 Annex M POTS non-overlapped (F) 41 - G.992.5 Annex M POTS overlapped (F)
1-默认/通用PSD配置。当找不到其他匹配的模式特定配置时，将使用默认配置。2-ADSL系列。特定于模式的PSD配置中包含的属性与ITU-T G.992.1和G.992.2 ADSL模式无关。因此，可以将这些模式映射到此泛型类。3-7-未使用。为将来的ITU-T规范保留。8-G.992.3非重叠的盆（F）9-G.992.3重叠的盆（F）10-G.992.3 ISDN非重叠的盆（F）11-G.992.3 ISDN重叠的盆（F）12-13-未使用。为将来的ITU-T规范保留。14-G.992.4罐非重叠（L）15-G.992.4罐重叠（L）16-17-未使用。为将来的ITU-T规范保留。18-G.992.3附件一全数字不重叠（F）19-G.992.3附件一全数字重叠（F）20-G.992.3附件J全数字不重叠（F）21-G.992.3附件J全数字重叠（F）22-G.992.4附件一全数字不重叠（L）23-G.992.4附件一全数字重叠（L）24-G.992.3附件L盆不重叠，模式1，宽U/S（F）25-G.992.3附件L盆不重叠，模式2，窄U/S（F）26-G.992.3附件L盆重叠，模式3，宽U/S（F）27-G.992.3附件L盆重叠，模式4，窄U/S（F）28-G.992.3附件M盆不重叠（F）29-G.992.3附件M盆重叠（F）30-G.992.5盆不重叠（F）31-G.992.5 POTS重叠（F）32-G.992.5 ISDN非重叠（F）33-G.992.5 ISDN重叠（F）34-35-未使用。为将来的ITU-T规范保留。36-G.992.5附件一全数字不重叠（F）37-G.992.5附件一全数字重叠（F）38-G.992.5附件J全数字不重叠（F）39-G.992.5附件J全数字重叠（F）40-G.992.5附件M盆不重叠（F）41-G.992.5附件M盆重叠（F）
"
SYNTAX INTEGER {
defMode (1),
adsl(2),
g9923PotsNonOverlapped(8),
g9923PotsOverlapped(9),
g9923IsdnNonOverlapped(10),
g9923isdnOverlapped(11),
g9924potsNonOverlapped(14),
g9924potsOverlapped(15),
g9923AnnexIAllDigNonOverlapped(18),
g9923AnnexIAllDigOverlapped(19),
g9923AnnexJAllDigNonOverlapped(20),
g9923AnnexJAllDigOverlapped(21),
g9924AnnexIAllDigNonOverlapped(22),
g9924AnnexIAllDigOverlapped(23),
g9923AnnexLMode1NonOverlapped(24),
g9923AnnexLMode2NonOverlapped(25),
g9923AnnexLMode3Overlapped(26),
g9923AnnexLMode4Overlapped(27),
g9923AnnexMPotsNonOverlapped(28),
g9923AnnexMPotsOverlapped(29),
g9925PotsNonOverlapped(30),
g9925PotsOverlapped(31),
g9925IsdnNonOverlapped(32),
g9925isdnOverlapped(33),
g9925AnnexIAllDigNonOverlapped(36),
g9925AnnexIAllDigOverlapped(37),
g9925AnnexJAllDigNonOverlapped(38),
g9925AnnexJAllDigOverlapped(39),
g9925AnnexMPotsNonOverlapped(40),
g9925AnnexMPotsOverlapped(41)
}
"
SYNTAX INTEGER {
defMode (1),
adsl(2),
g9923PotsNonOverlapped(8),
g9923PotsOverlapped(9),
g9923IsdnNonOverlapped(10),
g9923isdnOverlapped(11),
g9924potsNonOverlapped(14),
g9924potsOverlapped(15),
g9923AnnexIAllDigNonOverlapped(18),
g9923AnnexIAllDigOverlapped(19),
g9923AnnexJAllDigNonOverlapped(20),
g9923AnnexJAllDigOverlapped(21),
g9924AnnexIAllDigNonOverlapped(22),
g9924AnnexIAllDigOverlapped(23),
g9923AnnexLMode1NonOverlapped(24),
g9923AnnexLMode2NonOverlapped(25),
g9923AnnexLMode3Overlapped(26),
g9923AnnexLMode4Overlapped(27),
g9923AnnexMPotsNonOverlapped(28),
g9923AnnexMPotsOverlapped(29),
g9925PotsNonOverlapped(30),
g9925PotsOverlapped(31),
g9925IsdnNonOverlapped(32),
g9925isdnOverlapped(33),
g9925AnnexIAllDigNonOverlapped(36),
g9925AnnexIAllDigOverlapped(37),
g9925AnnexJAllDigNonOverlapped(38),
g9925AnnexJAllDigOverlapped(39),
g9925AnnexMPotsNonOverlapped(40),
g9925AnnexMPotsOverlapped(41)
}
Adsl2PowerMngState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax uniquely identify each power
management state defined for the ADSL/ADSL2 or ADSL2+ link.
The possible values are:
l0(1) - L0 - Full power management state.
l1(2) - L1 - Low power management state (for G.992.2).
l2(3) - L2 - Low power management state (for G.992.3,
G.992.4, and G.992.5).
l3(4) - L3 - Idle power management state."
Adsl2PowerMngState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax uniquely identify each power
management state defined for the ADSL/ADSL2 or ADSL2+ link.
The possible values are:
l0(1) - L0 - Full power management state.
l1(2) - L1 - Low power management state (for G.992.2).
l2(3) - L2 - Low power management state (for G.992.3,
G.992.4, and G.992.5).
l3(4) - L3 - Idle power management state."
SYNTAX INTEGER {
语法整数{
l0(1), l1(2), l2(3), l3(4) }
l0（1），l1（2），l2（3），l3（4）}
Adsl2ConfPmsForce ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that reference the desired power management state for the
ADSL/ADSL2 or ADSL2+ link:
l3toL0(0) - Perform a transition from L3 to L0
(Full power management state).
l0toL2(2) - Perform a transition from L0 to L2
(Low power management state).
l0orL2toL3(3) - Perform a transition into L3 (Idle
power management state).
Adsl2ConfPmsForce ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that reference the desired power management state for the
ADSL/ADSL2 or ADSL2+ link:
l3toL0(0) - Perform a transition from L3 to L0
(Full power management state).
l0toL2(2) - Perform a transition from L0 to L2
(Low power management state).
l0orL2toL3(3) - Perform a transition into L3 (Idle
power management state).
The values used are as defined in ITU-T G.997.1, paragraph 7.3.1.1.3"
使用的值如ITU-T G.997.1第7.3.1.1.3.段所定义
SYNTAX INTEGER {
l3toL0(0),
l0toL2(2),
l0orL2toL3(3)
}
SYNTAX INTEGER {
l3toL0(0),
l0toL2(2),
l0orL2toL3(3)
}
Adsl2LConfProfPmMode ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that reference the power modes/states into which the ATU-C or
ATU-R may autonomously transit.
Adsl2LConfProfPmMode ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that reference the power modes/states into which the ATU-C or
ATU-R may autonomously transit.
It is a BITS structure that allows control of the following transit options: allowTransitionsToIdle(0) - XTU may autonomously transit to idle (L3) state. allowTransitionsToLowPower(1) - XTU may autonomously transit to low-power (L2) state."
它是一种BITS结构，允许控制以下传输选项：allowTransitionsToIdle（0）-XTU可以自动传输到idle（L3）状态。allowTransitionsToLowPower（1）-XTU可以自动过渡到低功耗（L2）状态。”
SYNTAX BITS {
allowTransitionsToIdle(0),
allowTransitionsToLowPower(1)
}
SYNTAX BITS {
allowTransitionsToIdle(0),
allowTransitionsToLowPower(1)
}
Adsl2LineLdsf ::= TEXTUAL-CONVENTION
Adsl2LineLdsf ::= TEXTUAL-CONVENTION
STATUS current DESCRIPTION "Attributes with this syntax are configuration parameters that control the Loop Diagnostic mode for the ADSL/ADSL2 or ADSL2+ link. The possible values are: inhibit(0) - Inhibit Loop Diagnostic mode. force(1) - Force/Initiate Loop Diagnostic mode.
此语法的“状态当前描述”属性是控制ADSL/ADSL2或ADSL2+链路环路诊断模式的配置参数。可能的值为：禁止（0）-禁止环路诊断模式。强制（1）-强制/启动环路诊断模式。
The values used are as defined in ITU-T G.997.1, paragraph 7.3.1.1.8"
使用的值如ITU-T G.997.1第7.3.1.1.8.段所定义
SYNTAX INTEGER {
inhibit(0),
force(1)
}
SYNTAX INTEGER {
inhibit(0),
force(1)
}
Adsl2LdsfResult ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Possible failure reasons associated with performing
a Dual Ended Loop Test (DELT) on a DSL line.
Possible values are:
none(1) - The default value in case LDSF was never
requested for the associated line.
success(2) - The recent command completed
successfully.
inProgress(3) - The Loop Diagnostics process is in
progress.
unsupported(4) - The NE or the line card doesn't support
LDSF.
cannotRun(5) - The NE cannot initiate the command, due
to a nonspecific reason.
aborted(6) - The Loop Diagnostics process aborted.
failed(7) - The Loop Diagnostics process failed.
illegalMode(8) - The NE cannot initiate the command, due
to the specific mode of the relevant
line.
adminUp(9) - The NE cannot initiate the command, as
the relevant line is administratively
'Up'.
tableFull(10) - The NE cannot initiate the command, due
to reaching the maximum number of rows
in the results table.
noResources(11) - The NE cannot initiate the command, due
to lack of internal memory resources."
SYNTAX INTEGER {
none(1),
success(2),
Adsl2LdsfResult ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Possible failure reasons associated with performing
a Dual Ended Loop Test (DELT) on a DSL line.
Possible values are:
none(1) - The default value in case LDSF was never
requested for the associated line.
success(2) - The recent command completed
successfully.
inProgress(3) - The Loop Diagnostics process is in
progress.
unsupported(4) - The NE or the line card doesn't support
LDSF.
cannotRun(5) - The NE cannot initiate the command, due
to a nonspecific reason.
aborted(6) - The Loop Diagnostics process aborted.
failed(7) - The Loop Diagnostics process failed.
illegalMode(8) - The NE cannot initiate the command, due
to the specific mode of the relevant
line.
adminUp(9) - The NE cannot initiate the command, as
the relevant line is administratively
'Up'.
tableFull(10) - The NE cannot initiate the command, due
to reaching the maximum number of rows
in the results table.
noResources(11) - The NE cannot initiate the command, due
to lack of internal memory resources."
SYNTAX INTEGER {
none(1),
success(2),
inProgress(3), unsupported(4), cannotRun(5), aborted(6), failed(7), illegalMode(8), adminUp(9), tableFull(10), noResources(11) }
inProgress（3）、unsupported（4）、cannotRun（5）、中止（6）、failed（7）、illegalMode（8）、adminUp（9）、tableFull（10）、noResources（11）}
Adsl2SymbolProtection ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that reference the minimum-length impulse noise protection
(INP) in terms of number of symbols. The possible values are:
noProtection (i.e., INP not required), halfSymbol (i.e., INP
length is 1/2 symbol), and 1-16 symbols in steps of 1 symbol."
Adsl2SymbolProtection ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that reference the minimum-length impulse noise protection
(INP) in terms of number of symbols. The possible values are:
noProtection (i.e., INP not required), halfSymbol (i.e., INP
length is 1/2 symbol), and 1-16 symbols in steps of 1 symbol."
SYNTAX INTEGER {
noProtection(1),
halfSymbol(2),
singleSymbol(3),
twoSymbols(4),
threeSymbols(5),
fourSymbols(6),
fiveSymbols(7),
sixSymbols(8),
sevenSymbols(9),
eightSymbols(10),
nineSymbols(11),
tenSymbols(12),
elevenSymbols(13),
twelveSymbols(14),
thirteeSymbols(15),
fourteenSymbols(16),
fifteenSymbols(17),
sixteenSymbols(18)
}
Adsl2MaxBer ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that reference the maximum Bit Error Rate (BER).
The possible values are:
SYNTAX INTEGER {
noProtection(1),
halfSymbol(2),
singleSymbol(3),
twoSymbols(4),
threeSymbols(5),
fourSymbols(6),
fiveSymbols(7),
sixSymbols(8),
sevenSymbols(9),
eightSymbols(10),
nineSymbols(11),
tenSymbols(12),
elevenSymbols(13),
twelveSymbols(14),
thirteeSymbols(15),
fourteenSymbols(16),
fifteenSymbols(17),
sixteenSymbols(18)
}
Adsl2MaxBer ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are configuration parameters
that reference the maximum Bit Error Rate (BER).
The possible values are:
eminus3(1) - Maximum BER=E^-3
eminus3(1) - Maximum BER=E^-3
eminus5(2) - Maximum BER=E^-5
eminus7(3) - Maximum BER=E^-7"
SYNTAX INTEGER {
eminus3(1),
eminus5(2),
eminus7(3)
}
eminus5(2) - Maximum BER=E^-5
eminus7(3) - Maximum BER=E^-7"
SYNTAX INTEGER {
eminus3(1),
eminus5(2),
eminus7(3)
}
Adsl2ScMaskDs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Each one of the 512 bits in this OCTET
STRING array represents the corresponding bin
in the downstream direction. A value of one
indicates that the bin is not in use."
SYNTAX OCTET STRING (SIZE(0..64))
Adsl2ScMaskDs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Each one of the 512 bits in this OCTET
STRING array represents the corresponding bin
in the downstream direction. A value of one
indicates that the bin is not in use."
SYNTAX OCTET STRING (SIZE(0..64))
Adsl2ScMaskUs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Each one of the 64 bits in this OCTET
STRING array represents the corresponding bin
in the upstream direction. A value of one
indicates that the bin is not in use."
SYNTAX OCTET STRING (SIZE(0..8))
Adsl2ScMaskUs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Each one of the 64 bits in this OCTET
STRING array represents the corresponding bin
in the upstream direction. A value of one
indicates that the bin is not in use."
SYNTAX OCTET STRING (SIZE(0..8))
Adsl2RfiDs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Each one of the 512 bits in this OCTET
STRING array represents the corresponding bin
in the downstream direction. A value of one
indicates that the bin is part of a notch
filter."
SYNTAX OCTET STRING (SIZE(0..64))
Adsl2RfiDs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Each one of the 512 bits in this OCTET
STRING array represents the corresponding bin
in the downstream direction. A value of one
indicates that the bin is part of a notch
filter."
SYNTAX OCTET STRING (SIZE(0..64))
Adsl2PsdMaskDs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is a structure that represents up to
32 PSD Mask breakpoints.
Each breakpoint occupies 3 octets: The first
two octets hold the index of the sub-carrier
associated with the breakpoint. The third octet
holds the PSD reduction at the breakpoint from 0
(0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of
0.5 dBm/Hz."
SYNTAX OCTET STRING (SIZE(0..96))
Adsl2PsdMaskDs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is a structure that represents up to
32 PSD Mask breakpoints.
Each breakpoint occupies 3 octets: The first
two octets hold the index of the sub-carrier
associated with the breakpoint. The third octet
holds the PSD reduction at the breakpoint from 0
(0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of
0.5 dBm/Hz."
SYNTAX OCTET STRING (SIZE(0..96))
Adsl2PsdMaskUs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is a structure that represents up to
4 PSD Mask breakpoints.
Each breakpoint occupies 3 octets: The first
two octets hold the index of the sub-carrier
associated with the breakpoint. The third octet
holds the PSD reduction at the breakpoint from 0
(0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of
0.5 dBm/Hz."
SYNTAX OCTET STRING (SIZE(0..12))
Adsl2PsdMaskUs ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is a structure that represents up to
4 PSD Mask breakpoints.
Each breakpoint occupies 3 octets: The first
two octets hold the index of the sub-carrier
associated with the breakpoint. The third octet
holds the PSD reduction at the breakpoint from 0
(0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of
0.5 dBm/Hz."
SYNTAX OCTET STRING (SIZE(0..12))
Adsl2Tssi ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is a structure that represents up to
32 transmit spectrum shaping (TSSi) breakpoints.
Each breakpoint occupies 3 octets: The first
two octets hold the index of the sub-carrier
associated with the breakpoint. The third octet
holds the shaping parameter at the breakpoint. It
is a value from 0 to 127 (units of -0.5 dB). The
special value 127 indicates that the sub-carrier
is not transmitted."
SYNTAX OCTET STRING (SIZE(0..96))
Adsl2Tssi ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is a structure that represents up to
32 transmit spectrum shaping (TSSi) breakpoints.
Each breakpoint occupies 3 octets: The first
two octets hold the index of the sub-carrier
associated with the breakpoint. The third octet
holds the shaping parameter at the breakpoint. It
is a value from 0 to 127 (units of -0.5 dB). The
special value 127 indicates that the sub-carrier
is not transmitted."
SYNTAX OCTET STRING (SIZE(0..96))
Adsl2LastTransmittedState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This parameter represents the last successfully
transmitted initialization state in the last full
initialization performed on the line. States are
per the specific xDSL technology and are numbered
from 0 (if G.994.1 is used) or 1 (if G.994.1 is
not used) up to Showtime."
SYNTAX INTEGER {
atucG9941(0),
atucQuiet1(1),
atucComb1(2),
atucQuiet2(3),
atucComb2(4),
atucIcomb1(5),
atucLineprob(6),
atucQuiet3(7),
atucComb3(8),
atucIComb2(9),
atucMsgfmt(10),
Adsl2LastTransmittedState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This parameter represents the last successfully
transmitted initialization state in the last full
initialization performed on the line. States are
per the specific xDSL technology and are numbered
from 0 (if G.994.1 is used) or 1 (if G.994.1 is
not used) up to Showtime."
SYNTAX INTEGER {
atucG9941(0),
atucQuiet1(1),
atucComb1(2),
atucQuiet2(3),
atucComb2(4),
atucIcomb1(5),
atucLineprob(6),
atucQuiet3(7),
atucComb3(8),
atucIComb2(9),
atucMsgfmt(10),
atucMsgpcb(11), atucQuiet4(12), atucReverb1(13), atucTref1(14), atucReverb2(15), atucEct(16), atucReverb3(17), atucTref2(18), atucReverb4(19), atucSegue1(20), atucMsg1(21), atucReverb5(22), atucSegue2(23), atucMedley(24), atucExchmarker(25), atucMsg2(26), atucReverb6(27), atucSegue3(28), atucParams(29), atucReverb7(30), atucSegue4(31), atucShowtime(32), -- aturG9941(100), aturQuiet1(101), aturComb1(102), aturQuiet2(103), aturComb2(104), aturIcomb1(105), aturLineprob(106), aturQuiet3(107), aturComb3(108), aturIcomb2(109), aturMsgfmt(110), aturMsgpcb(111), aturReverb1(112), aturQuiet4(113), aturReverb2(114), aturQuiet5(115), aturReverb3(116), aturEct(117), aturReverb4(118), aturSegue1(119), aturReverb5(120), aturSegue2(121), aturMsg1(122), aturMedley(123), aturExchmarker(124),
atucMsgpcb（11）、atucQuiet4（12）、atucReverb1（13）、atucref1（14）、atucReverb2（15）、atucref（16）、atucReverb3（17）、atucref2（18）、atucReverb4（19）、atucSegue1（20）、atucMsg1（21）、atucReverb5（22）、atucSegue2（23）、atucMedley（24）、atucExchmarker（25）、atucMsg2（26）、atucReverb6（27）、atucSegue3（28）、atucParams（29）、atucsegue7（30）、atb31、，atucShowtime（32）、aturG9941（100）、ATURKIET1（101）、aturComb1（102）、ATURKIET2（103）、aturComb2（104）、aturIcomb1（105）、ATURINEPROB（106）、ATURKIET3（107）、aturComb3（108）、aturIcomb2（109）、aturMsgfmt（110）、aturMsgpcb（111）、aturReverb1（112）、ATURKIET4（113）、aturReverb2（114）、ATURKIET5（115）、aturReverb3（116）、aturReverb4（118），阿图尔塞格1（119）、阿图尔塞格5（120）、阿图尔塞格2（121）、阿图尔姆斯格1（122）、阿图尔梅德利（123）、阿图尔塞克马克（124），
aturMsg2(125), aturReverb6(126), aturSegue3(127), aturParams(128), aturReverb7(129), aturSegue4(130), aturShowtime(131) }
aturMsg2（125）、aturReverb6（126）、aturSegue3（127）、aturParams（128）、aturReverb7（129）、aturSegue4（130）、aturShowtime（131）}
Adsl2LineStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are status parameters
that reflect the failure status for a given endpoint of
ADSL/ADSL2 or ADSL2+ link.
Adsl2LineStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are status parameters
that reflect the failure status for a given endpoint of
ADSL/ADSL2 or ADSL2+ link.
This BITS structure can report the following failures:
此BITS结构可报告以下故障：
noDefect(0) - This bit position positively reports
that no defect or failure exists.
lossOfFrame(1) - Loss of frame synchronization.
lossOfSignal(2) - Loss of signal.
lossOfPower(3) - Loss of power. Usually this failure may
be reported for ATU-Rs only.
initFailure(4) - Recent initialization process failed.
Never active on ATU-R."
noDefect(0) - This bit position positively reports
that no defect or failure exists.
lossOfFrame(1) - Loss of frame synchronization.
lossOfSignal(2) - Loss of signal.
lossOfPower(3) - Loss of power. Usually this failure may
be reported for ATU-Rs only.
initFailure(4) - Recent initialization process failed.
Never active on ATU-R."
SYNTAX BITS {
noDefect(0),
lossOfFrame(1),
lossOfSignal(2),
lossOfPower(3),
initFailure(4)
}
SYNTAX BITS {
noDefect(0),
lossOfFrame(1),
lossOfSignal(2),
lossOfPower(3),
initFailure(4)
}
Adsl2ChAtmStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are status parameters that
reflect the failure status for Transmission Convergence (TC)
layer of a given ATM interface (data path over an ADSL/ADSL2
or ADSL2+ link).
Adsl2ChAtmStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are status parameters that
reflect the failure status for Transmission Convergence (TC)
layer of a given ATM interface (data path over an ADSL/ADSL2
or ADSL2+ link).
This BITS structure can report the following failures: noDefect(0) - This bit position positively reports that no defect or failure exists. noCellDelineation(1) - The link was successfully
此BITS结构可以报告以下故障：noDefect（0）-此位位置肯定报告不存在缺陷或故障。nocell描述（1）-链接成功
initialized, but cell delineation was never acquired on the associated ATM data path. lossOfCellDelineation(2) - Loss of cell delineation on the associated ATM data path."
已初始化，但从未在关联的ATM数据路径上获取信元描述。LossOfCellDescription（2）-相关ATM数据路径上的信元描绘丢失。”
SYNTAX BITS {
noDefect(0),
noCellDelineation(1),
lossOfCellDelineation(2)
}
SYNTAX BITS {
noDefect(0),
noCellDelineation(1),
lossOfCellDelineation(2)
}
Adsl2ChPtmStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are status parameters that
reflect the failure status for a given PTM interface (packet
data path over an ADSL/ADSL2 or ADSL2+ link).
Adsl2ChPtmStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Attributes with this syntax are status parameters that
reflect the failure status for a given PTM interface (packet
data path over an ADSL/ADSL2 or ADSL2+ link).
This BITS structure can report the following failures: noDefect(0) - This bit position positively reports that no defect or failure exists. outOfSync(1) - Out of synchronization."
此BITS结构可以报告以下故障：noDefect（0）-此位位置肯定报告不存在缺陷或故障。不同步（1）-不同步。“
SYNTAX BITS {
noDefect(0),
outOfSync(1)
}
SYNTAX BITS {
noDefect(0),
outOfSync(1)
}
END
终止
ADSL2-LINE-MIB DEFINITIONS ::= BEGIN
ADSL2-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS MODULE-IDENTITY, OBJECT-TYPE, transmission, Unsigned32, NOTIFICATION-TYPE, Integer32, Counter32 FROM SNMPv2-SMI
从SNMPv2 SMI导入模块标识、对象类型、传输、未签名32、通知类型、整数32、计数器32
ifIndex FROM IF-MIB
来自IF-MIB的ifIndex
TruthValue, RowStatus FROM SNMPv2-TC
来自SNMPv2 TC的真实值、行状态
SnmpAdminString FROM SNMP-FRAMEWORK-MIB
SNMP-FRAMEWORK-MIB中的snmpadmin安装
HCPerfIntervalThreshold, HCPerfTimeElapsed FROM HC-PerfHist-TC-MIB -- [RFC3705]
HCPerfIntervalThreshold，HCPerfTime从HC PerfHist TC MIB经过--[RFC3705]
Adsl2Unit, Adsl2Direction, Adsl2TransmissionModeType, Adsl2RaMode, Adsl2InitResult, Adsl2OperationModes, Adsl2PowerMngState, Adsl2ConfPmsForce, Adsl2LConfProfPmMode, Adsl2LineLdsf, Adsl2LdsfResult, Adsl2SymbolProtection, Adsl2MaxBer, Adsl2ScMaskDs, Adsl2ScMaskUs, Adsl2RfiDs, Adsl2PsdMaskDs, Adsl2PsdMaskUs, Adsl2Tssi, Adsl2LastTransmittedState, Adsl2LineStatus, Adsl2ChAtmStatus,
ADSL2单元、ADSL2方向、ADSL2传输模式、ADSL2模块、ADSL2模拟结果、ADSL2操作模式、ADSL2电源状态、Adsl2ConfPmsForce、ADSL2ConfProfPMMODE、ADSL2LINEDSF、ADSL2LDFRESULT、Adsl2SymbolProtection、Adsl2MaxBer、Adsl2ScMaskDs、ADSL2SCMASKU、ADSL2FIDS、ADSL2PSDMASKU、ADSL2PSDMASKU、ADSL2LSI、Adsl2LastTransmittedState、，Adsl2LineStatus，Adsl2ChAtmStatus，
Adsl2ChPtmStatus FROM ADSL2-LINE-TC-MIB -- [This document]
来自ADSL2-LINE-TC-MIB的Adsl2ChPtmStatus--[本文件]
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF;
来自SNMPv2 CONF的MODULE-COMPLIANCE、OBJECT-GROUP、NOTIFICATION-GROUP；
adsl2MIB MODULE-IDENTITY
LAST-UPDATED "200610040000Z" -- October 4th, 2006
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
adsl2MIB MODULE-IDENTITY
LAST-UPDATED "200610040000Z" -- October 4th, 2006
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed Sand Channel Systems Postal: P.O. Box 37324 Raleigh NC 27627-732 Email: sneedmike@hotmail.com Phone: +1 206 600 7022
主席：Mike Sneed Sand Channel Systems邮政：北卡罗来纳州罗利市37324信箱27627-732电子邮件：sneedmike@hotmail.com电话：+1206600722
Co-Chair & Co-editor: Menachem Dodge ECI Telecom Ltd. Postal: 30 Hasivim St. Petach Tikva 49517, Israel. Email: mbdodge@ieee.org Phone: +972 3 926 8421
共同主席和共同编辑：Menahem Dodge ECI Telecom Ltd.邮政编码：30 Hasivim St.Petach Tikva 49517，以色列。电邮：mbdodge@ieee.org电话：+97239268421
Co-editor: Moti Morgenstern ECI Telecom Ltd. Postal: 30 Hasivim St. Petach Tikva 49517, Israel. Email: moti.morgenstern@ecitele.com Phone: +972 3 926 6258
共同编辑：Moti Morgenstern ECI电信有限公司，邮政编码：30 Hasivim St.Petach Tikva 49517，以色列。电子邮件：moti。morgenstern@ecitele.com电话：+9723926658
Co-editor: Scott Baillie NEC Australia Postal: 649-655 Springvale Road, Mulgrave, Victoria 3170, Australia. Email: scott.baillie@nec.com.au Phone: +61 3 9264 3986
合编：Scott Baillie NEC澳大利亚邮政：澳大利亚维多利亚州马尔格雷夫市斯普林维尔路649-655号，邮编3170。电子邮件：斯科特。baillie@nec.com.au电话：+61 3 9264 3986
Co-editor: Umberto Bonollo
合编：翁贝托·博诺洛
NEC Australia Postal: 649-655 Springvale Road, Mulgrave, Victoria 3170, Australia. Email: umberto.bonollo@nec.com.au Phone: +61 3 9264 3385 " DESCRIPTION " This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managing ADSL, ADSL2, and ADSL2+ lines. The MIB module described in RFC 2662 [RFC2662] describes objects used for managing Asymmetric Bit-Rate DSL (ADSL) interfaces per [T1E1.413], [G.992.1], and [G.992.2]. These object descriptions are based upon the specifications for the ADSL Embedded Operations Channel (EOC) as defined in American National Standards Institute (ANSI) T1E1.413/1995 [T1E1.413] and International Telecommunication Union (ITU-T) G.992.1 [G.992.1] and G.992.2 [G.992.2].
NEC澳大利亚邮政：澳大利亚维多利亚州马尔格雷夫市斯普林维尔路649-655号，邮编3170。电邮：umberto。bonollo@nec.com.au电话：+61 3 9264 3385“说明”本文档定义了一个管理信息库（MIB）模块，用于互联网社区中的网络管理协议，用于管理ADSL、ADSL2和ADSL2+线路。RFC 2662[RFC2662]中描述的MIB模块描述了用于按照[T1E1.413]、[G.992.1]和[G.992.2]管理非对称比特率DSL（ADSL）接口的对象。这些对象描述基于美国国家标准协会（ANSI）T1E1.413/1995[T1E1.413]和国际电信联盟（ITU-T）G.992.1[G.992.1]和G.992.2[G.992.2]中定义的ADSL嵌入式操作信道（EOC）规范。
This document does not obsolete RFC 2662 [RFC2662], but rather provides a more comprehensive management model that includes the ADSL2 and ADSL2+ technologies per G.992.3, G.992.4, and G.992.5 ([G.992.3], [G.992.4], and [G.992.5], respectively). In addition, objects have been added to improve the management of ADSL, ADSL2, and ADSL2+ lines.
本文件并未废弃RFC 2662[RFC2662]，而是提供了一个更全面的管理模型，其中包括符合G.992.3、G.992.4和G.992.5的ADSL2和ADSL2+技术（分别为[G.992.3]、[G.992.4]和[G.992.5]）。此外，还添加了对象以改进ADSL、ADSL2和ADSL2+线路的管理。
Additionally, the management framework for New Generation ADSL lines specified by the Digital Subscriber Line Forum (DSLF) has been taken into consideration [TR-90]. That framework is based on ITU-T G.997.1 standard [G.997.1] as well as two amendments: [G.997.1am1] and [G.997.1am2].
此外，还考虑了数字用户线路论坛（DSLF）规定的新一代ADSL线路管理框架[TR-90]。该框架基于ITU-T G.997.1标准[G.997.1]以及两个修正案[G.997.1am1]和[G.997.1am2]。
Note that the revised ITU-T G.997.1 standard also refers to the next generation of VDSL technology, known as VDSL2, per ITU-T G.993.2 [G.993.2]. However, managing VDSL2 lines is currently beyond the scope of this document.
请注意，根据ITU-T G.993.2[G.993.2]，修订后的ITU-T G.997.1标准还参考了下一代VDSL技术，称为VDSL2。但是，管理VDSL2线路目前超出了本文档的范围。
The MIB module is located in the MIB tree under MIB 2 transmission, as discussed in the IANA Considerations section of this document.
MIB模块位于MIB 2传输下的MIB树中，如本文档IANA注意事项部分所述。
Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4706: see the RFC itself for full legal notices."
版权所有（C）互联网协会（2006年）。此MIB模块的此版本是RFC 4706的一部分：有关完整的法律通知，请参阅RFC本身。”
REVISION "200610040000Z" -- October 4th, 2006
DESCRIPTION "Initial version, published as RFC 4706."
::= { transmission 238 }
REVISION "200610040000Z" -- October 4th, 2006
DESCRIPTION "Initial version, published as RFC 4706."
::= { transmission 238 }
adsl2 OBJECT IDENTIFIER ::= { adsl2MIB 1 }
------------------------------------------------
adsl2Line OBJECT IDENTIFIER ::= { adsl2 1 }
adsl2Status OBJECT IDENTIFIER ::= { adsl2 2 }
adsl2Inventory OBJECT IDENTIFIER ::= { adsl2 3 }
adsl2PM OBJECT IDENTIFIER ::= { adsl2 4 }
adsl2Profile OBJECT IDENTIFIER ::= { adsl2 5 }
adsl2Scalar OBJECT IDENTIFIER ::= { adsl2 6 }
adsl2Notifications OBJECT IDENTIFIER ::= { adsl2 0 }
adsl2Conformance OBJECT IDENTIFIER ::= { adsl2 7 }
------------------------------------------------
adsl2PMLine OBJECT IDENTIFIER ::= { adsl2PM 1 }
adsl2PMChannel OBJECT IDENTIFIER ::= { adsl2PM 2 }
------------------------------------------------
adsl2ProfileLine OBJECT IDENTIFIER ::= { adsl2Profile 1 }
adsl2ProfileChannel OBJECT IDENTIFIER ::= { adsl2Profile 2 }
adsl2ProfileAlarmConf OBJECT IDENTIFIER ::= { adsl2Profile 3 }
------------------------------------------------
adsl2ScalarSC OBJECT IDENTIFIER ::= { adsl2Scalar 1 }
------------------------------------------------
adsl2 OBJECT IDENTIFIER ::= { adsl2MIB 1 }
------------------------------------------------
adsl2Line OBJECT IDENTIFIER ::= { adsl2 1 }
adsl2Status OBJECT IDENTIFIER ::= { adsl2 2 }
adsl2Inventory OBJECT IDENTIFIER ::= { adsl2 3 }
adsl2PM OBJECT IDENTIFIER ::= { adsl2 4 }
adsl2Profile OBJECT IDENTIFIER ::= { adsl2 5 }
adsl2Scalar OBJECT IDENTIFIER ::= { adsl2 6 }
adsl2Notifications OBJECT IDENTIFIER ::= { adsl2 0 }
adsl2Conformance OBJECT IDENTIFIER ::= { adsl2 7 }
------------------------------------------------
adsl2PMLine OBJECT IDENTIFIER ::= { adsl2PM 1 }
adsl2PMChannel OBJECT IDENTIFIER ::= { adsl2PM 2 }
------------------------------------------------
adsl2ProfileLine OBJECT IDENTIFIER ::= { adsl2Profile 1 }
adsl2ProfileChannel OBJECT IDENTIFIER ::= { adsl2Profile 2 }
adsl2ProfileAlarmConf OBJECT IDENTIFIER ::= { adsl2Profile 3 }
------------------------------------------------
adsl2ScalarSC OBJECT IDENTIFIER ::= { adsl2Scalar 1 }
------------------------------------------------
------------------------------------------------
-- adsl2LineTable --
------------------------------------------------
adsl2LineTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineTable contains configuration,
command, and status parameters of the ADSL2 line.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238).
------------------------------------------------
-- adsl2LineTable --
------------------------------------------------
adsl2LineTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineTable contains configuration,
command, and status parameters of the ADSL2 line.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238).
Several objects in this table MUST be maintained in a
persistent manner."
::= { adsl2Line 1 }
Several objects in this table MUST be maintained in a
persistent manner."
::= { adsl2Line 1 }
adsl2LineEntry OBJECT-TYPE SYNTAX Adsl2LineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION
adsl2LineEntry对象类型语法adsl2LineEntry MAX-ACCESS不可访问状态当前说明
"The table adsl2LineTable contains configuration,
commands, and status parameters of the ADSL2 line"
INDEX { ifIndex }
::= { adsl2LineTable 1 }
"The table adsl2LineTable contains configuration,
commands, and status parameters of the ADSL2 line"
INDEX { ifIndex }
::= { adsl2LineTable 1 }
Adsl2LineEntry ::=
SEQUENCE {
adsl2LineCnfgTemplate SnmpAdminString,
adsl2LineAlarmCnfgTemplate SnmpAdminString,
adsl2LineCmndConfPmsf Adsl2ConfPmsForce,
adsl2LineCmndConfLdsf Adsl2LineLdsf,
adsl2LineCmndConfLdsfFailReason Adsl2LdsfResult,
adsl2LineCmndAutomodeColdStart TruthValue,
adsl2LineStatusAtuTransSys Adsl2TransmissionModeType,
adsl2LineStatusPwrMngState Adsl2PowerMngState,
adsl2LineStatusInitResult Adsl2InitResult,
adsl2LineStatusLastStateDs Adsl2LastTransmittedState,
adsl2LineStatusLastStateUs Adsl2LastTransmittedState,
adsl2LineStatusAtur Adsl2LineStatus,
adsl2LineStatusAtuc Adsl2LineStatus,
adsl2LineStatusLnAttenDs Unsigned32,
adsl2LineStatusLnAttenUs Unsigned32,
adsl2LineStatusSigAttenDs Unsigned32,
adsl2LineStatusSigAttenUs Unsigned32,
adsl2LineStatusSnrMarginDs Integer32,
adsl2LineStatusSnrMarginUs Integer32,
adsl2LineStatusAttainableRateDs Unsigned32,
adsl2LineStatusAttainableRateUs Unsigned32,
adsl2LineStatusActPsdDs Integer32,
adsl2LineStatusActPsdUs Integer32,
adsl2LineStatusActAtpDs Integer32,
adsl2LineStatusActAtpUs Integer32
}
Adsl2LineEntry ::=
SEQUENCE {
adsl2LineCnfgTemplate SnmpAdminString,
adsl2LineAlarmCnfgTemplate SnmpAdminString,
adsl2LineCmndConfPmsf Adsl2ConfPmsForce,
adsl2LineCmndConfLdsf Adsl2LineLdsf,
adsl2LineCmndConfLdsfFailReason Adsl2LdsfResult,
adsl2LineCmndAutomodeColdStart TruthValue,
adsl2LineStatusAtuTransSys Adsl2TransmissionModeType,
adsl2LineStatusPwrMngState Adsl2PowerMngState,
adsl2LineStatusInitResult Adsl2InitResult,
adsl2LineStatusLastStateDs Adsl2LastTransmittedState,
adsl2LineStatusLastStateUs Adsl2LastTransmittedState,
adsl2LineStatusAtur Adsl2LineStatus,
adsl2LineStatusAtuc Adsl2LineStatus,
adsl2LineStatusLnAttenDs Unsigned32,
adsl2LineStatusLnAttenUs Unsigned32,
adsl2LineStatusSigAttenDs Unsigned32,
adsl2LineStatusSigAttenUs Unsigned32,
adsl2LineStatusSnrMarginDs Integer32,
adsl2LineStatusSnrMarginUs Integer32,
adsl2LineStatusAttainableRateDs Unsigned32,
adsl2LineStatusAttainableRateUs Unsigned32,
adsl2LineStatusActPsdDs Integer32,
adsl2LineStatusActPsdUs Integer32,
adsl2LineStatusActAtpDs Integer32,
adsl2LineStatusActAtpUs Integer32
}
adsl2LineCnfgTemplate OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL2 Line Configuration Templates Table, (adsl2LineConfTemplateTable), which applies for this ADSL2 line.
ADSL2LINECNFGTAMPLATE对象类型语法SnmpAdminString（大小（1..32））MAX-ACCESS读写状态当前描述“此对象的值标识ADSL2线路配置模板表（adsl2LineConfTemplateTable）中适用于此ADSL2线路的行。
This object MUST be maintained in a persistent manner."
REFERENCE "DSL Forum TR-90, paragraph 5.1.1"
DEFVAL { "DEFVAL" }
::= { adsl2LineEntry 1 }
This object MUST be maintained in a persistent manner."
REFERENCE "DSL Forum TR-90, paragraph 5.1.1"
DEFVAL { "DEFVAL" }
::= { adsl2LineEntry 1 }
adsl2LineAlarmCnfgTemplate OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL2 Line Alarm Configuration Template Table, (adsl2LineAlarmConfTemplateTable), which applies to this ADSL2 line.
adsl2LineAlarmCnfgTemplate对象类型语法SNMPAdministring（大小（1..32））MAX-ACCESS读写状态当前描述“此对象的值标识ADSL2线路报警配置模板表（adsl2LineAlarmConfTemplateTable）中适用于此ADSL2线路的行。
This object MUST be maintained in a persistent manner."
REFERENCE "DSL Forum TR-90, paragraph 5.1.1"
DEFVAL { "DEFVAL" }
::= { adsl2LineEntry 2 }
This object MUST be maintained in a persistent manner."
REFERENCE "DSL Forum TR-90, paragraph 5.1.1"
DEFVAL { "DEFVAL" }
::= { adsl2LineEntry 2 }
adsl2LineCmndConfPmsf OBJECT-TYPE SYNTAX Adsl2ConfPmsForce MAX-ACCESS read-write STATUS current DESCRIPTION "Power management state forced. Defines the line states to be forced by the near-end ATU on this line. The various possible values are: l3toL0(0), l0toL2(2), or l0orL2toL3(3).
adsl2LineCmndConfPmsf对象类型语法Adsl2ConfPmsForce MAX-ACCESS读写状态当前描述“强制电源管理状态”。定义此线路上近端ATU强制的线路状态。各种可能的值为：l3toL0（0）、l0toL2（2）或l0orL2toL3（3）。
This object MUST be maintained in a persistent manner."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.3"
DEFVAL { l3toL0 }
::= { adsl2LineEntry 3 }
This object MUST be maintained in a persistent manner."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.3"
DEFVAL { l3toL0 }
::= { adsl2LineEntry 3 }
adsl2LineCmndConfLdsf OBJECT-TYPE SYNTAX Adsl2LineLdsf MAX-ACCESS read-write STATUS current DESCRIPTION "Loop diagnostics mode forced (LDSF). Defines whether the line should be forced into the loop diagnostics mode by the near-end ATU on this line or only be responsive to loop diagnostics initiated by the far-end ATU.
adsl2LineCmndConfLdsf对象类型语法ADSL2LINEDSF MAX-ACCESS读写状态当前描述“强制循环诊断模式（LDSF）”。定义该线路上的近端ATU应强制该线路进入循环诊断模式，还是仅响应远端ATU启动的循环诊断。
This object MUST be maintained in a persistent manner. However, in case the operator forces loop diagnostics mode then the access node should reset the object (inhibit) when loop diagnostics mode procedures are completed." REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.8" DEFVAL { inhibit }
必须以持久方式维护此对象。但是，如果操作员强制环路诊断模式，则当环路诊断模式程序完成时，接入节点应重置对象（禁止）。“参考”ITU-T G.997.1，段落7.3.1.1.8“定义{inhibit}”
::= { adsl2LineEntry 4 }
::= { adsl2LineEntry 4 }
adsl2LineCmndConfLdsfFailReason OBJECT-TYPE
SYNTAX Adsl2LdsfResult
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of the recent occasion the Loop diagnostics mode
forced (LDSF) was issued for the associated line. Possible
values are:
none(1) - The default value in case LDSF was never
requested for the associated line.
success(2) - The recent command completed
successfully.
inProgress(3) - The Loop Diagnostics process is in
progress.
unsupported(4) - The NE or the line card doesn't support
LDSF.
cannotRun(5) - The NE cannot initiate the command, due
to a nonspecific reason.
aborted(6) - The Loop Diagnostics process aborted.
failed(7) - The Loop Diagnostics process failed.
illegalMode(8) - The NE cannot initiate the command, due
to the specific mode of the relevant
line.
adminUp(9) - The NE cannot initiate the command, as
the relevant line is administratively
'Up'.
tableFull(10) - The NE cannot initiate the command, due
to reaching the maximum number of rows
in the results table.
noResources(11) - The NE cannot initiate the command, due
to lack of internal memory resources."
DEFVAL { none }
::= { adsl2LineEntry 5 }
adsl2LineCmndConfLdsfFailReason OBJECT-TYPE
SYNTAX Adsl2LdsfResult
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of the recent occasion the Loop diagnostics mode
forced (LDSF) was issued for the associated line. Possible
values are:
none(1) - The default value in case LDSF was never
requested for the associated line.
success(2) - The recent command completed
successfully.
inProgress(3) - The Loop Diagnostics process is in
progress.
unsupported(4) - The NE or the line card doesn't support
LDSF.
cannotRun(5) - The NE cannot initiate the command, due
to a nonspecific reason.
aborted(6) - The Loop Diagnostics process aborted.
failed(7) - The Loop Diagnostics process failed.
illegalMode(8) - The NE cannot initiate the command, due
to the specific mode of the relevant
line.
adminUp(9) - The NE cannot initiate the command, as
the relevant line is administratively
'Up'.
tableFull(10) - The NE cannot initiate the command, due
to reaching the maximum number of rows
in the results table.
noResources(11) - The NE cannot initiate the command, due
to lack of internal memory resources."
DEFVAL { none }
::= { adsl2LineEntry 5 }
adsl2LineCmndAutomodeColdStart OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Automode cold start forced. This parameter is defined in order to improve testing of the performance of ATUs supporting automode when it is enabled in the MIB. Change the value of this parameter to 'true' indicates a change in loop conditions applied to the devices under test. The ATUs shall reset any historical information used for automode and for shortening G.994.1 handshake
ADSL2LINECMDAUTOMODECOLDSTART对象类型语法TruthValue MAX-ACCESS读写状态当前说明“自动模式冷启动强制。定义此参数是为了在MIB中启用自动模式时，改进对支持自动模式的ATU性能的测试。将此参数的值更改为“真”表示应用于被测设备的回路条件发生变化。ATU应重置用于自动模式和缩短G.994.1握手的任何历史信息
and initialization.
和初始化。
Automode is the case where multiple operation-modes are enabled through the adsl2LConfProfAtuTransSysEna object in the line configuration profile being used for the ADSL line, and where the selection of the actual operation-mode depends not only on the common capabilities of both ATUs (as exchanged in G.994.1), but also on achievable data rates under given loop conditions.
自动模式是指通过ADSL线路使用的线路配置配置文件中的adsl2LConfProfAtuTransSysEna对象启用多个操作模式的情况，并且实际操作模式的选择不仅取决于两个ATU的通用功能（如G.994.1中所述），但也取决于给定循环条件下可实现的数据速率。
This object MUST be maintained in a persistent manner."
必须以持久方式维护此对象。”
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.1.10"
DEFVAL { false }
::= { adsl2LineEntry 6 }
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.1.10"
DEFVAL { false }
::= { adsl2LineEntry 6 }
adsl2LineStatusAtuTransSys OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU Transmission System (ATS) in use.
It is coded in a bit-map representation with only a single bit
set to '1' (the selected coding for the ADSL line). This
parameter may be derived from the handshaking procedures
defined in Recommendation G.994.1. A set of ADSL2 line
transmission modes, with one bit per mode."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.1"
::= { adsl2LineEntry 7 }
adsl2LineStatusAtuTransSys OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU Transmission System (ATS) in use.
It is coded in a bit-map representation with only a single bit
set to '1' (the selected coding for the ADSL line). This
parameter may be derived from the handshaking procedures
defined in Recommendation G.994.1. A set of ADSL2 line
transmission modes, with one bit per mode."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.1"
::= { adsl2LineEntry 7 }
adsl2LineStatusPwrMngState OBJECT-TYPE
SYNTAX Adsl2PowerMngState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current power management state. One of four possible
power management states:
L0 - Synchronized and full transmission (i.e., Showtime).
L1 - Low Power with reduced net data rate (G.992.2 only).
L2 - Low Power with reduced net data rate (G.992.3 and
G.992.4 only).
L3 - No power.
The various possible values are: l0(1), l1(2), l2(3), or
l3(4)."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.2"
::= { adsl2LineEntry 8 }
adsl2LineStatusPwrMngState OBJECT-TYPE
SYNTAX Adsl2PowerMngState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current power management state. One of four possible
power management states:
L0 - Synchronized and full transmission (i.e., Showtime).
L1 - Low Power with reduced net data rate (G.992.2 only).
L2 - Low Power with reduced net data rate (G.992.3 and
G.992.4 only).
L3 - No power.
The various possible values are: l0(1), l1(2), l2(3), or
l3(4)."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.2"
::= { adsl2LineEntry 8 }
adsl2LineStatusInitResult OBJECT-TYPE
SYNTAX Adsl2InitResult
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the result of the last full initialization performed
on the line. It is an enumeration type with the following
values: noFail(0), configError(1), configNotFeasible(2),
commFail(3), noPeerAtu(4), or otherCause(5)."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.3"
::= { adsl2LineEntry 9 }
adsl2LineStatusInitResult OBJECT-TYPE
SYNTAX Adsl2InitResult
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the result of the last full initialization performed
on the line. It is an enumeration type with the following
values: noFail(0), configError(1), configNotFeasible(2),
commFail(3), noPeerAtu(4), or otherCause(5)."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.3"
::= { adsl2LineEntry 9 }
adsl2LineStatusLastStateDs OBJECT-TYPE
SYNTAX Adsl2LastTransmittedState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last successful transmitted initialization state in
the downstream direction in the last full initialization
performed on the line."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.4"
::= { adsl2LineEntry 10 }
adsl2LineStatusLastStateDs OBJECT-TYPE
SYNTAX Adsl2LastTransmittedState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last successful transmitted initialization state in
the downstream direction in the last full initialization
performed on the line."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.4"
::= { adsl2LineEntry 10 }
adsl2LineStatusLastStateUs OBJECT-TYPE
SYNTAX Adsl2LastTransmittedState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last successful transmitted initialization state in the
upstream direction in the last full initialization performed
on the line."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.5"
::= { adsl2LineEntry 11 }
adsl2LineStatusLastStateUs OBJECT-TYPE
SYNTAX Adsl2LastTransmittedState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last successful transmitted initialization state in the
upstream direction in the last full initialization performed
on the line."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.5"
::= { adsl2LineEntry 11 }
adsl2LineStatusAtur OBJECT-TYPE
SYNTAX Adsl2LineStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state (existing failures) of the ATU-R.
This is a bit-map of possible conditions."
REFERENCE "ITU-T G.997.1, paragraph 7.1.1.2"
::= { adsl2LineEntry 12 }
adsl2LineStatusAtur OBJECT-TYPE
SYNTAX Adsl2LineStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state (existing failures) of the ATU-R.
This is a bit-map of possible conditions."
REFERENCE "ITU-T G.997.1, paragraph 7.1.1.2"
::= { adsl2LineEntry 12 }
adsl2LineStatusAtuc OBJECT-TYPE SYNTAX Adsl2LineStatus MAX-ACCESS read-only STATUS current
Adsl2LineStatus对象类型语法Adsl2LineStatus MAX-ACCESS只读状态当前
DESCRIPTION
"Indicates current state (existing failures) of the ATU-C.
This is a bit-map of possible conditions."
REFERENCE "ITU-T G.997.1, paragraph 7.1.1.1"
::= { adsl2LineEntry 13 }
DESCRIPTION
"Indicates current state (existing failures) of the ATU-C.
This is a bit-map of possible conditions."
REFERENCE "ITU-T G.997.1, paragraph 7.1.1.1"
::= { adsl2LineEntry 13 }
adsl2LineStatusLnAttenDs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub-
carriers during diagnostics mode and initialization. It
ranges from 0 to 1270 units of 0.1 dB (physical values
are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the line
attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the line
attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.6"
::= { adsl2LineEntry 14 }
adsl2LineStatusLnAttenDs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub-
carriers during diagnostics mode and initialization. It
ranges from 0 to 1270 units of 0.1 dB (physical values
are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the line
attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the line
attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.6"
::= { adsl2LineEntry 14 }
adsl2LineStatusLnAttenUs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub-
carriers during diagnostics mode and initialization.
It ranges from 0 to 1270 units of 0.1 dB (physical values are
0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the line
attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the line
attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.7"
::= { adsl2LineEntry 15 }
adsl2LineStatusLnAttenUs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub-
carriers during diagnostics mode and initialization.
It ranges from 0 to 1270 units of 0.1 dB (physical values are
0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the line
attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the line
attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.7"
::= { adsl2LineEntry 15 }
adsl2LineStatusSigAttenDs OBJECT-TYPE SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION
ADSL2LINESTATUSSIGATTEDS对象类型语法无符号32（0..1270 | 2147483646 | 2147483647）单元“0.1 dB”最大访问只读状态当前说明
"The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub-
carriers during Showtime. It ranges from 0 to 1270 units of
0.1 dB (physical values are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
signal attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
signal attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.8"
::= { adsl2LineEntry 16 }
"The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub-
carriers during Showtime. It ranges from 0 to 1270 units of
0.1 dB (physical values are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
signal attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
signal attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.8"
::= { adsl2LineEntry 16 }
adsl2LineStatusSigAttenUs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub-
carriers during Showtime. It ranges from 0 to 1270 units of
0.1 dB (physical values are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
signal attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
signal attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.9"
::= { adsl2LineEntry 17 }
adsl2LineStatusSigAttenUs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub-
carriers during Showtime. It ranges from 0 to 1270 units of
0.1 dB (physical values are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
signal attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
signal attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.9"
::= { adsl2LineEntry 17 }
adsl2LineStatusSnrMarginDs OBJECT-TYPE
SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Downstream SNR Margin is the maximum increase in dB of the
noise power received at the ATU-R, such that the BER
requirements are met for all downstream bearer channels. It
ranges from -640 to 630 units of 0.1 dB (physical values are
-64 to 63 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
SNR Margin is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
SNR Margin measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.10"
::= { adsl2LineEntry 18 }
adsl2LineStatusSnrMarginDs OBJECT-TYPE
SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Downstream SNR Margin is the maximum increase in dB of the
noise power received at the ATU-R, such that the BER
requirements are met for all downstream bearer channels. It
ranges from -640 to 630 units of 0.1 dB (physical values are
-64 to 63 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
SNR Margin is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
SNR Margin measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.10"
::= { adsl2LineEntry 18 }
adsl2LineStatusSnrMarginUs OBJECT-TYPE SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647)
adsl2LineStatusSnrMarginUs对象类型语法整数32（-640..630 | 2147483646 | 2147483647）
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Upstream SNR Margin is the maximum increase in dB of the noise
power received at the ATU-C, such that the BER requirements
are met for all downstream bearer channels. It ranges from
-640 to 630 units of 0.1 dB (physical values are -64 to
63 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
SNR Margin is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
SNR Margin measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.11"
::= { adsl2LineEntry 19 }
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Upstream SNR Margin is the maximum increase in dB of the noise
power received at the ATU-C, such that the BER requirements
are met for all downstream bearer channels. It ranges from
-640 to 630 units of 0.1 dB (physical values are -64 to
63 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
SNR Margin is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
SNR Margin measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.11"
::= { adsl2LineEntry 19 }
adsl2LineStatusAttainableRateDs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate Downstream.
The maximum downstream net data rate currently attainable by
the ATU-C transmitter and the ATU-R receiver, coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.12"
::= { adsl2LineEntry 20 }
adsl2LineStatusAttainableRateDs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate Downstream.
The maximum downstream net data rate currently attainable by
the ATU-C transmitter and the ATU-R receiver, coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.12"
::= { adsl2LineEntry 20 }
adsl2LineStatusAttainableRateUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate Upstream.
The maximum upstream net data rate currently attainable by the
ATU-R transmitter and the ATU-C receiver, coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.13"
::= { adsl2LineEntry 21 }
adsl2LineStatusAttainableRateUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate Upstream.
The maximum upstream net data rate currently attainable by the
ATU-R transmitter and the ATU-C receiver, coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.13"
::= { adsl2LineEntry 21 }
adsl2LineStatusActPsdDs OBJECT-TYPE SYNTAX Integer32 (-900..0 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION
adsl2LineStatusActPsdDs对象类型语法整数32（-900..0 | 2147483647）单位“0.1 dB”最大访问只读状态当前说明
"Actual Power Spectrum Density (PSD) Downstream. The average
downstream transmit PSD over the sub-carriers used for
downstream. It ranges from -900 to 0 units of 0.1 dB
(physical values are -90 to 0 dBm/Hz).
A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.14"
::= { adsl2LineEntry 22 }
"Actual Power Spectrum Density (PSD) Downstream. The average
downstream transmit PSD over the sub-carriers used for
downstream. It ranges from -900 to 0 units of 0.1 dB
(physical values are -90 to 0 dBm/Hz).
A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.14"
::= { adsl2LineEntry 22 }
adsl2LineStatusActPsdUs OBJECT-TYPE
SYNTAX Integer32 (-900..0 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Power Spectrum Density (PSD) Upstream. The average
upstream transmit PSD over the sub-carriers used for upstream.
It ranges from -900 to 0 units of 0.1 dB (physical values
are -90 to 0 dBm/Hz).
A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.15"
::= { adsl2LineEntry 23 }
adsl2LineStatusActPsdUs OBJECT-TYPE
SYNTAX Integer32 (-900..0 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Power Spectrum Density (PSD) Upstream. The average
upstream transmit PSD over the sub-carriers used for upstream.
It ranges from -900 to 0 units of 0.1 dB (physical values
are -90 to 0 dBm/Hz).
A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.15"
::= { adsl2LineEntry 23 }
adsl2LineStatusActAtpDs OBJECT-TYPE
SYNTAX Integer32 (-310..310 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Aggregate Transmit Power Downstream. The total amount
of transmit power delivered by the ATU-C at the U-C reference
point, at the instant of measurement. It ranges from -310 to
310 units of 0.1 dB (physical values are -31 to 31 dBm).
A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.16"
::= { adsl2LineEntry 24 }
adsl2LineStatusActAtpDs OBJECT-TYPE
SYNTAX Integer32 (-310..310 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Aggregate Transmit Power Downstream. The total amount
of transmit power delivered by the ATU-C at the U-C reference
point, at the instant of measurement. It ranges from -310 to
310 units of 0.1 dB (physical values are -31 to 31 dBm).
A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.16"
::= { adsl2LineEntry 24 }
adsl2LineStatusActAtpUs OBJECT-TYPE SYNTAX Integer32 (-310..310 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the ATU-R at the U-R reference point, at the instant of measurement. It ranges
adsl2LineStatusActAtpUs对象类型语法整数32（-310..310 | 2147483647）单位“0.1 dB”最大访问只读状态当前描述“上游实际总发射功率”。测量瞬间，ATU-R在U-R参考点提供的发射功率总量。其范围为
from -310 to 310 units of 0.1 dB (physical values are -31
to 31 dBm).
A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.17"
::= { adsl2LineEntry 25 }
from -310 to 310 units of 0.1 dB (physical values are -31
to 31 dBm).
A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.17"
::= { adsl2LineEntry 25 }
------------------------------------------------
-- adsl2ChannelStatusTable --
------------------------------------------------
adsl2ChannelStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2ChannelStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChannelStatusTable contains status
parameters of the ADSL2 channel. This table contains live
data from equipment."
::= { adsl2Status 1 }
------------------------------------------------
-- adsl2ChannelStatusTable --
------------------------------------------------
adsl2ChannelStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2ChannelStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChannelStatusTable contains status
parameters of the ADSL2 channel. This table contains live
data from equipment."
::= { adsl2Status 1 }
adsl2ChannelStatusEntry OBJECT-TYPE
SYNTAX Adsl2ChannelStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChannelStatusTable contains status
parameters of the ADSL2 channel.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a DSL channel, along with a termination unit."
INDEX { ifIndex, adsl2ChStatusUnit }
::= { adsl2ChannelStatusTable 1 }
adsl2ChannelStatusEntry OBJECT-TYPE
SYNTAX Adsl2ChannelStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChannelStatusTable contains status
parameters of the ADSL2 channel.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a DSL channel, along with a termination unit."
INDEX { ifIndex, adsl2ChStatusUnit }
::= { adsl2ChannelStatusTable 1 }
Adsl2ChannelStatusEntry ::=
SEQUENCE {
adsl2ChStatusUnit Adsl2Unit,
adsl2ChStatusChannelNum Unsigned32,
adsl2ChStatusActDataRate Unsigned32,
adsl2ChStatusPrevDataRate Unsigned32,
adsl2ChStatusActDelay Unsigned32,
adsl2ChStatusAtmStatus Adsl2ChAtmStatus,
adsl2ChStatusPtmStatus Adsl2ChPtmStatus
}
Adsl2ChannelStatusEntry ::=
SEQUENCE {
adsl2ChStatusUnit Adsl2Unit,
adsl2ChStatusChannelNum Unsigned32,
adsl2ChStatusActDataRate Unsigned32,
adsl2ChStatusPrevDataRate Unsigned32,
adsl2ChStatusActDelay Unsigned32,
adsl2ChStatusAtmStatus Adsl2ChAtmStatus,
adsl2ChStatusPtmStatus Adsl2ChPtmStatus
}
adsl2ChStatusUnit OBJECT-TYPE SYNTAX Adsl2Unit MAX-ACCESS not-accessible
adsl2ChStatusUnit对象类型语法Adsl2Unit MAX-ACCESS不可访问
STATUS current
DESCRIPTION
"The termination unit atuc(1) or atur(2)."
::= { adsl2ChannelStatusEntry 1 }
STATUS current
DESCRIPTION
"The termination unit atuc(1) or atur(2)."
::= { adsl2ChannelStatusEntry 1 }
adsl2ChStatusChannelNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the bearer channel number associated with this
row (i.e., the channel ifIndex).
This enables determining the channel configuration profile
and the channel thresholds profile applicable for this
bearer channel."
::= { adsl2ChannelStatusEntry 2 }
adsl2ChStatusChannelNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the bearer channel number associated with this
row (i.e., the channel ifIndex).
This enables determining the channel configuration profile
and the channel thresholds profile applicable for this
bearer channel."
::= { adsl2ChannelStatusEntry 2 }
adsl2ChStatusActDataRate OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual net data rate that the bearer channel is operating
at, if in L0 power management state. In L1 or L2 states, it
relates to the previous L0 state. The data rate is coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.2.1"
::= { adsl2ChannelStatusEntry 3 }
adsl2ChStatusActDataRate OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual net data rate that the bearer channel is operating
at, if in L0 power management state. In L1 or L2 states, it
relates to the previous L0 state. The data rate is coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.2.1"
::= { adsl2ChannelStatusEntry 3 }
adsl2ChStatusPrevDataRate OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The previous net data rate that the bearer channel was
operating at just before the latest rate change event. This
could be a full or short initialization, fast retrain, DRA or
power management transitions, excluding transitions between L0
state and L1 or L2 states. The data rate is coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.2.2"
::= { adsl2ChannelStatusEntry 4 }
adsl2ChStatusPrevDataRate OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The previous net data rate that the bearer channel was
operating at just before the latest rate change event. This
could be a full or short initialization, fast retrain, DRA or
power management transitions, excluding transitions between L0
state and L1 or L2 states. The data rate is coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.2.2"
::= { adsl2ChannelStatusEntry 4 }
adsl2ChStatusActDelay OBJECT-TYPE SYNTAX Unsigned32(0..8176) UNITS "milliseconds"
adsl2ChStatusActDelay对象类型语法无符号32（0..8176）单位“毫秒”
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual one-way interleaving delay introduced by the
PMS-TC in the direction of the bearer channel, if in L0
power management state. In L1 or L2 states, it relates to
the previous L0 state. It is coded in ms (rounded to the
nearest ms)."
REFERENCE "ITU-T G.997.1, paragraph 7.5.2.3"
::= { adsl2ChannelStatusEntry 5 }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual one-way interleaving delay introduced by the
PMS-TC in the direction of the bearer channel, if in L0
power management state. In L1 or L2 states, it relates to
the previous L0 state. It is coded in ms (rounded to the
nearest ms)."
REFERENCE "ITU-T G.997.1, paragraph 7.5.2.3"
::= { adsl2ChannelStatusEntry 5 }
adsl2ChStatusAtmStatus OBJECT-TYPE
SYNTAX Adsl2ChAtmStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current state (existing failures) of the ADSL
channel in case its Data Path is ATM. This is a bit-map of
possible conditions. The various bit positions are:
noDefect(0),
noCellDelineation(1), or
lossOfCellDelineation(2).
In the case where the channel is not an ATM Data Path, the
object is set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.1.4"
::= { adsl2ChannelStatusEntry 6 }
adsl2ChStatusAtmStatus OBJECT-TYPE
SYNTAX Adsl2ChAtmStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current state (existing failures) of the ADSL
channel in case its Data Path is ATM. This is a bit-map of
possible conditions. The various bit positions are:
noDefect(0),
noCellDelineation(1), or
lossOfCellDelineation(2).
In the case where the channel is not an ATM Data Path, the
object is set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.1.4"
::= { adsl2ChannelStatusEntry 6 }
adsl2ChStatusPtmStatus OBJECT-TYPE
SYNTAX Adsl2ChPtmStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current state (existing failures) of the ADSL
channel in case its Data Path is PTM. This is a bit-map of
possible conditions. The various bit positions are:
noDefect(0), or
outOfSync(1).
In the case where the channel is not a PTM Data Path, the
object is set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.1.5"
::= { adsl2ChannelStatusEntry 7 }
adsl2ChStatusPtmStatus OBJECT-TYPE
SYNTAX Adsl2ChPtmStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current state (existing failures) of the ADSL
channel in case its Data Path is PTM. This is a bit-map of
possible conditions. The various bit positions are:
noDefect(0), or
outOfSync(1).
In the case where the channel is not a PTM Data Path, the
object is set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.1.5"
::= { adsl2ChannelStatusEntry 7 }
------------------------------------------------
-- Scalars that relate to the adsl2SCStatusTable.
------------------------------------------------
------------------------------------------------
-- Scalars that relate to the adsl2SCStatusTable.
------------------------------------------------
adsl2ScalarSCMaxInterfaces OBJECT-TYPE
adsl2ScalarSCMaxInterfaces对象类型
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value determines the upper size of adsl2SCStatusTable.
The maximum number of entries in adsl2SCStatusTable is equal
to two times the value of this attribute."
::= { adsl2ScalarSC 1 }
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value determines the upper size of adsl2SCStatusTable.
The maximum number of entries in adsl2SCStatusTable is equal
to two times the value of this attribute."
::= { adsl2ScalarSC 1 }
adsl2ScalarSCAvailInterfaces OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value determines the amount of space that is
currently available in adsl2SCStatusTable.
The number of entries available in adsl2SCStatusTable is equal
to two times the value of this attribute."
::= { adsl2ScalarSC 2 }
adsl2ScalarSCAvailInterfaces OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value determines the amount of space that is
currently available in adsl2SCStatusTable.
The number of entries available in adsl2SCStatusTable is equal
to two times the value of this attribute."
::= { adsl2ScalarSC 2 }
------------------------------------------------
-- adsl2SCStatusTable --
------------------------------------------------
------------------------------------------------
-- adsl2SCStatusTable --
------------------------------------------------
adsl2SCStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF Adsl2SCStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The following points apply to this table: 1. The main purpose of this table is to hold the results of a DELT. 2. This table also holds parameters obtained at line initialization time. 3. The rows in this table are volatile; that is, they are lost if the SNMP agent is rebooted. 4. Due to the large OCTET STRING attributes in this table, the worst case memory requirements for this table are very high. The manager may use the row status attribute of this table to delete rows in order to reclaim memory. 5. The manager may create rows in this table. The SNMP agent may create rows in this table. Only the manager may delete rows in this table. 6. The maximum number of rows allowable in this table is indicated by the scalar attribute adsl2ScalarSCMaxInterfaces.
adsl2SCStatusTable对象类型语法序列Adsl2SCStatusEntry MAX-ACCESS不可访问状态当前描述“ADSL2SCStatus表包含ADSL2子载波的状态参数。以下几点适用于本表：1。此表的主要目的是保存DELT的结果。2.此表还包含在线路初始化时获得的参数。3.此表中的行不稳定；也就是说，如果重新启动SNMP代理，它们将丢失。4.由于此表中有较大的八位字节字符串属性，因此此表的最坏情况内存需求非常高。管理器可以使用此表的“行状态”属性删除行以回收内存。5.经理可以在此表中创建行。SNMP代理可以在此表中创建行。只有管理器可以删除此表中的行。6.此表中允许的最大行数由标量属性adsl2ScalarSCMaxInterfaces表示。
The number of rows available in this table is indicated
by the scalar attribute adsl2ScalarSCAvailInterfaces.
7. The SNMP agent is permitted to create rows in this table
when a DELT completes successfully or when line
initialization occurs. It is not mandatory for the SNMP
agent to create rows in this table; hence, it may be
necessary for the manager to create rows in this table
before any results can be stored.
8. If the manager attempts to create a row in this table
and there are no more rows available, the creation
attempt will fail, and the response to the SNMP SET PDU
will contain the error noCreation(11).
9. If the SNMP agent attempts to create a row in this table
and there are no more rows available, the creation
attempt will fail, and the attribute
adsl2LineCmndConfLdsfFailReason will indicate the
reason for the failure. The failure reason will be either
tableFull(10) or noResources(11).
10. An example of use of this table is as follows:
Step 1. : The DELT is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT completes, and valid data is
: available.
Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so
: the SNMP agent attempts to create the row.
Step 4. : Due to a low memory condition, a row in the
: adsl2SCStatusTable table cannot be created at
: this time.
Step 5. : The reason for the failure, tableFull(10), is
: indicated in the adsl2LineCmndConfLdsfFailReason
: attribute.
11. Another example of use of this table is as follows :
Step 1. : The DELT is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT completes and valid data is
: available.
Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so
: the SNMP agent attempts to create the row.
Step 4. : The row creation is successful.
Step 5. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2).
12. Another example of use of this table is as follows:
Step 1. : The manager creates a row in adsl2SCStatusTable
: for a particular ADSL2 line.
Step 2. : The DELT is started on the above-mentioned
The number of rows available in this table is indicated
by the scalar attribute adsl2ScalarSCAvailInterfaces.
7. The SNMP agent is permitted to create rows in this table
when a DELT completes successfully or when line
initialization occurs. It is not mandatory for the SNMP
agent to create rows in this table; hence, it may be
necessary for the manager to create rows in this table
before any results can be stored.
8. If the manager attempts to create a row in this table
and there are no more rows available, the creation
attempt will fail, and the response to the SNMP SET PDU
will contain the error noCreation(11).
9. If the SNMP agent attempts to create a row in this table
and there are no more rows available, the creation
attempt will fail, and the attribute
adsl2LineCmndConfLdsfFailReason will indicate the
reason for the failure. The failure reason will be either
tableFull(10) or noResources(11).
10. An example of use of this table is as follows:
Step 1. : The DELT is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT completes, and valid data is
: available.
Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so
: the SNMP agent attempts to create the row.
Step 4. : Due to a low memory condition, a row in the
: adsl2SCStatusTable table cannot be created at
: this time.
Step 5. : The reason for the failure, tableFull(10), is
: indicated in the adsl2LineCmndConfLdsfFailReason
: attribute.
11. Another example of use of this table is as follows :
Step 1. : The DELT is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT completes and valid data is
: available.
Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so
: the SNMP agent attempts to create the row.
Step 4. : The row creation is successful.
Step 5. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2).
12. Another example of use of this table is as follows:
Step 1. : The manager creates a row in adsl2SCStatusTable
: for a particular ADSL2 line.
Step 2. : The DELT is started on the above-mentioned
: line by setting the adsl2LineCmndConfLdsf from
: inhibit to force.
Step 3. : The DELT completes, and valid data is
: available.
Step 4. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2)."
::= { adsl2Status 2 }
: line by setting the adsl2LineCmndConfLdsf from
: inhibit to force.
Step 3. : The DELT completes, and valid data is
: available.
Step 4. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2)."
::= { adsl2Status 2 }
adsl2SCStatusEntry OBJECT-TYPE
SYNTAX Adsl2SCStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2SCStatusEntry contains status parameters
of the ADSL2 sub-carriers.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238)."
INDEX { ifIndex, adsl2SCStatusDirection }
::= { adsl2SCStatusTable 1 }
adsl2SCStatusEntry OBJECT-TYPE
SYNTAX Adsl2SCStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2SCStatusEntry contains status parameters
of the ADSL2 sub-carriers.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238)."
INDEX { ifIndex, adsl2SCStatusDirection }
::= { adsl2SCStatusTable 1 }
Adsl2SCStatusEntry ::=
SEQUENCE {
adsl2SCStatusDirection Adsl2Direction,
adsl2SCStatusMtime Unsigned32,
adsl2SCStatusSnr OCTET STRING,
adsl2SCStatusBitsAlloc OCTET STRING,
adsl2SCStatusGainAlloc OCTET STRING,
adsl2SCStatusTssi Adsl2Tssi,
adsl2SCStatusLinScale Unsigned32,
adsl2SCStatusLinReal OCTET STRING,
adsl2SCStatusLinImg OCTET STRING,
adsl2SCStatusLogMt Unsigned32,
adsl2SCStatusLog OCTET STRING,
adsl2SCStatusQlnMt Unsigned32,
adsl2SCStatusQln OCTET STRING,
adsl2SCStatusLnAtten Unsigned32,
adsl2SCStatusSigAtten Unsigned32,
adsl2SCStatusSnrMargin Integer32,
adsl2SCStatusAttainableRate Unsigned32,
adsl2SCStatusActAtp Integer32,
adsl2SCStatusRowStatus RowStatus
}
Adsl2SCStatusEntry ::=
SEQUENCE {
adsl2SCStatusDirection Adsl2Direction,
adsl2SCStatusMtime Unsigned32,
adsl2SCStatusSnr OCTET STRING,
adsl2SCStatusBitsAlloc OCTET STRING,
adsl2SCStatusGainAlloc OCTET STRING,
adsl2SCStatusTssi Adsl2Tssi,
adsl2SCStatusLinScale Unsigned32,
adsl2SCStatusLinReal OCTET STRING,
adsl2SCStatusLinImg OCTET STRING,
adsl2SCStatusLogMt Unsigned32,
adsl2SCStatusLog OCTET STRING,
adsl2SCStatusQlnMt Unsigned32,
adsl2SCStatusQln OCTET STRING,
adsl2SCStatusLnAtten Unsigned32,
adsl2SCStatusSigAtten Unsigned32,
adsl2SCStatusSnrMargin Integer32,
adsl2SCStatusAttainableRate Unsigned32,
adsl2SCStatusActAtp Integer32,
adsl2SCStatusRowStatus RowStatus
}
adsl2SCStatusDirection OBJECT-TYPE SYNTAX Adsl2Direction MAX-ACCESS not-accessible STATUS current
adsl2SCStatusDirection对象类型语法Adsl2Direction MAX-ACCESS不可访问状态当前
DESCRIPTION
"The direction of the sub-carrier is either
upstream or downstream."
::= { adsl2SCStatusEntry 1 }
DESCRIPTION
"The direction of the sub-carrier is either
upstream or downstream."
::= { adsl2SCStatusEntry 1 }
adsl2SCStatusMtime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "symbols"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"SNR Measurement Time. The number of symbols used to
measure the SNR values on the respective transmission
direction. It should correspond to the value specified in the
recommendation (e.g., the number of symbols in 1 second
time interval for G.992.3). This parameter corresponds to
1 second in loop diagnostic procedure and should be updated
otherwise."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.20.1 (SNRMTds)
and paragraph 7.5.1.20.3 (SNRMTus)"
::= { adsl2SCStatusEntry 2 }
adsl2SCStatusMtime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "symbols"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"SNR Measurement Time. The number of symbols used to
measure the SNR values on the respective transmission
direction. It should correspond to the value specified in the
recommendation (e.g., the number of symbols in 1 second
time interval for G.992.3). This parameter corresponds to
1 second in loop diagnostic procedure and should be updated
otherwise."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.20.1 (SNRMTds)
and paragraph 7.5.1.20.3 (SNRMTus)"
::= { adsl2SCStatusEntry 2 }
adsl2SCStatusSnr OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..512))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SNR Margin per sub-carrier, expressing the ratio between
the received signal power and received noise power per
subscriber. It is an array of 512 octets, designed for
supporting up to 512 (downstream) sub-carriers.
The number of utilized octets on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Octet i (0 <= i < NSC) is set to a value in the range 0 to
254 to indicate that the respective downstream or upstream sub-
carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB
(i.e., -32 to 95dB).
The special value 255 means that no measurement could be done
for the subcarrier because it is out of the PSD mask passband
or that the noise PSD is out of range to be represented.
Each value in this array is 8 bits wide."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.20.2 (SNRpsds)
and paragraph 7.5.1.20.4 (SNRpsus)"
::= { adsl2SCStatusEntry 3 }
adsl2SCStatusSnr OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..512))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SNR Margin per sub-carrier, expressing the ratio between
the received signal power and received noise power per
subscriber. It is an array of 512 octets, designed for
supporting up to 512 (downstream) sub-carriers.
The number of utilized octets on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Octet i (0 <= i < NSC) is set to a value in the range 0 to
254 to indicate that the respective downstream or upstream sub-
carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB
(i.e., -32 to 95dB).
The special value 255 means that no measurement could be done
for the subcarrier because it is out of the PSD mask passband
or that the noise PSD is out of range to be represented.
Each value in this array is 8 bits wide."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.20.2 (SNRpsds)
and paragraph 7.5.1.20.4 (SNRpsus)"
::= { adsl2SCStatusEntry 3 }
adsl2SCStatusBitsAlloc OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..256))
adsl2SCStatusBitsAlloc对象类型语法八位字节字符串（大小（0..256））
UNITS "bits"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bits allocation per sub-carrier. An array of 256 octets
(512 nibbles), designed for supporting up to 512 (downstream)
sub-carriers.
The number of utilized nibbles on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Nibble i (0 <= i < NSC) is set to a value in the range 0
to 15 to indicate that the respective downstream or upstream
sub-carrier i has the same amount of bits allocation."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.1 (BITSpsds)
and paragraph 7.5.1.21.2 (BITSpsus)"
::= { adsl2SCStatusEntry 4 }
UNITS "bits"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bits allocation per sub-carrier. An array of 256 octets
(512 nibbles), designed for supporting up to 512 (downstream)
sub-carriers.
The number of utilized nibbles on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Nibble i (0 <= i < NSC) is set to a value in the range 0
to 15 to indicate that the respective downstream or upstream
sub-carrier i has the same amount of bits allocation."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.1 (BITSpsds)
and paragraph 7.5.1.21.2 (BITSpsus)"
::= { adsl2SCStatusEntry 4 }
adsl2SCStatusGainAlloc OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The gain allocation per sub-carrier. An array of 512 16-bits
values, designed for supporting up to 512 (downstream) sub-
carriers.
The number of utilized octets on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate
that the respective downstream or upstream sub-carrier i has the
same amount of gain value.
The gain value is represented as a multiple of 1/512 on a
linear scale. Each value in this array is 16 bits wide and is
stored in big endian format."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.3 (GAINSpsds)
and paragraph 7.5.1.21.4 (GAINSpsus)"
::= { adsl2SCStatusEntry 5 }
adsl2SCStatusGainAlloc OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The gain allocation per sub-carrier. An array of 512 16-bits
values, designed for supporting up to 512 (downstream) sub-
carriers.
The number of utilized octets on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate
that the respective downstream or upstream sub-carrier i has the
same amount of gain value.
The gain value is represented as a multiple of 1/512 on a
linear scale. Each value in this array is 16 bits wide and is
stored in big endian format."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.3 (GAINSpsds)
and paragraph 7.5.1.21.4 (GAINSpsus)"
::= { adsl2SCStatusEntry 5 }
adsl2SCStatusTssi OBJECT-TYPE SYNTAX Adsl2Tssi MAX-ACCESS read-only STATUS current DESCRIPTION "The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1. Each breakpoint is a pair of values occupying 3 octets with the following structure: First 2 octets - Index of the subcarrier used in the context of
adsl2SCStatusTssi对象类型语法ADSL2TSI MAX-ACCESS只读状态当前说明“发射频谱成形（TSSi）断点表示为G.994.1期间交换的断点集。每个断点是一对值，占据3个八位字节，具有以下结构：前2个八位字节-在
the breakpoint.
Third octet - The shaping parameter at the breakpoint.
Subcarrier index is an unsigned number in the range 1 to either
NSCds (downstream direction) or NSCus (upstream direction).
The shaping parameter value is in the range 0 to 127 (units of
-0.5dB). The special value 127 indicates that the subcarrier
is not transmitted."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.5 (TSSpsds)
and paragraph 7.5.1.21.6 (TSSpsus)"
::= { adsl2SCStatusEntry 6 }
the breakpoint.
Third octet - The shaping parameter at the breakpoint.
Subcarrier index is an unsigned number in the range 1 to either
NSCds (downstream direction) or NSCus (upstream direction).
The shaping parameter value is in the range 0 to 127 (units of
-0.5dB). The special value 127 indicates that the subcarrier
is not transmitted."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.5 (TSSpsds)
and paragraph 7.5.1.21.6 (TSSpsus)"
::= { adsl2SCStatusEntry 6 }
adsl2SCStatusLinScale OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The scale factor to be applied to the H(f) linear
representation values for the respective transmission direction.
This parameter is only available after a loop diagnostic
procedure."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.1 (HLINSCds)
and paragraph 7.5.1.18.5 (HLINSCus)"
::= { adsl2SCStatusEntry 7 }
adsl2SCStatusLinScale OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The scale factor to be applied to the H(f) linear
representation values for the respective transmission direction.
This parameter is only available after a loop diagnostic
procedure."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.1 (HLINSCds)
and paragraph 7.5.1.18.5 (HLINSCus)"
::= { adsl2SCStatusEntry 7 }
adsl2SCStatusLinReal OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..1024)) MAX-ACCESS read-only STATUS current DESCRIPTION "An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the real component [referred to here as a(i)] of Hlin(f = i*Df) value for a particular sub-carrier index i (0 <= i < NSC). Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is Adsl2SubcarrierLinScale and a(i) and b(i) [provided by the Adsl2SubcarrierLinImg object] are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure.
adsl2SCStatusLinReal对象类型语法八位字节字符串（大小（0..1024））MAX-ACCESS只读状态当前描述“一个数组，最多包含512个复杂的H（f）线性表示值，以线性比例表示各个传输方向。它设计为最多支持512个（下游）子载波。下行方向上使用的值的数量取决于NSCD，上行方向上使用的值的数量取决于NSCU。此值在此处称为NSC。每个数组项表示特定子载波索引i（0<=i<NSC）的Hlin（f=i*Df）值的真实分量[在此处称为a（i）]。Hlin（f）表示为（（标度/2^15）*（（a（i）+j*b（i））/2^15），其中标度为ADSL2SubcarrierInScale，且a（i）和b（i）[由ADSL2SubcarrierInimg对象提供]在范围（-2^15+1）到（+2^15-1）之间。特殊值a（i）=b（i）=-2^15表示无法对子载波进行测量，因为它超出了通带或衰减超出了要表示的范围。此参数仅在环路诊断程序后可用。
Each value in this array is 16 bits wide and is stored in big
endian format."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.2 (HLINpsds)
and paragraph 7.5.1.18.6 (HLINpsds)"
::= { adsl2SCStatusEntry 8 }
Each value in this array is 16 bits wide and is stored in big
endian format."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.2 (HLINpsds)
and paragraph 7.5.1.18.6 (HLINpsds)"
::= { adsl2SCStatusEntry 8 }
adsl2SCStatusLinImg OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of up to 512 complex H(f) linear representation
values in linear scale for the respective transmission
direction. It is designed to support up to 512 (downstream)
sub-carriers.
The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Each array entry represents the imaginary component [referred
to here as b(i)] of Hlin(f = i*Df) value for a particular sub-
carrier index i (0 <= i < NSC).
Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)),
where scale is Adsl2SubcarrierLinScale and a(i) [provided by
the Adsl2SubcarrierLinReal object] and b(i) are in the range
(-2^15+1) to (+2^15-1).
A special value a(i)=b(i)= -2^15 indicates that no measurement
could be done for the subcarrier because it is out of the
passband or that the attenuation is out of range to be
represented. This parameter is only available after a loop
diagnostic procedure.
Each value in this array is 16 bits wide and is stored in big
endian format."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.2 (HLINpsds)
and paragraph 7.5.1.18.6 (HLINpsds)"
::= { adsl2SCStatusEntry 9 }
adsl2SCStatusLinImg OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of up to 512 complex H(f) linear representation
values in linear scale for the respective transmission
direction. It is designed to support up to 512 (downstream)
sub-carriers.
The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Each array entry represents the imaginary component [referred
to here as b(i)] of Hlin(f = i*Df) value for a particular sub-
carrier index i (0 <= i < NSC).
Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)),
where scale is Adsl2SubcarrierLinScale and a(i) [provided by
the Adsl2SubcarrierLinReal object] and b(i) are in the range
(-2^15+1) to (+2^15-1).
A special value a(i)=b(i)= -2^15 indicates that no measurement
could be done for the subcarrier because it is out of the
passband or that the attenuation is out of range to be
represented. This parameter is only available after a loop
diagnostic procedure.
Each value in this array is 16 bits wide and is stored in big
endian format."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.2 (HLINpsds)
and paragraph 7.5.1.18.6 (HLINpsds)"
::= { adsl2SCStatusEntry 9 }
adsl2SCStatusLogMt OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of symbols used to measure the H(f) logarithmic measurement values for the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated in initialization"
adsl2SCStatusLogMt对象类型语法Unsigned32 MAX-ACCESS只读状态当前描述“用于测量各个传输方向的H（f）对数测量值的符号数。此参数应与建议中指定的值相对应（例如，g.992.3在1秒时间间隔内的符号数）。此参数对应1秒环路内诊断程序，应在初始化时更新“
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.3 (HLOGMTds)
and paragraph 7.5.1.18.7 (HLOGMTus)"
::= { adsl2SCStatusEntry 10 }
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.3 (HLOGMTds)
and paragraph 7.5.1.18.7 (HLOGMTus)"
::= { adsl2SCStatusEntry 10 }
adsl2SCStatusLog OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of up to 512 real H(f) logarithmic representation
values in dB for the respective transmission direction. It is
designed to support up to 512 (downstream) sub-carriers.
The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Each array entry represents the real Hlog(f = i*Df) value for a
particular sub-carrier index i, (0 <= i < NSC).
The real Hlog(f) value is represented as (6-m(i)/10), with m(i)
in the range 0 to 1022. A special value m=1023 indicates that
no measurement could be done for the subcarrier because it is
out of the passband or that the attenuation is out of range to
be represented. This parameter is applicable in loop
diagnostic procedure and initialization.
Each value in this array is 16 bits wide and is stored
in big endian format."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.4 (HLOGpsds)
and paragraph 7.5.1.18.8 (HLOGpsus)"
::= { adsl2SCStatusEntry 11 }
adsl2SCStatusLog OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of up to 512 real H(f) logarithmic representation
values in dB for the respective transmission direction. It is
designed to support up to 512 (downstream) sub-carriers.
The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Each array entry represents the real Hlog(f = i*Df) value for a
particular sub-carrier index i, (0 <= i < NSC).
The real Hlog(f) value is represented as (6-m(i)/10), with m(i)
in the range 0 to 1022. A special value m=1023 indicates that
no measurement could be done for the subcarrier because it is
out of the passband or that the attenuation is out of range to
be represented. This parameter is applicable in loop
diagnostic procedure and initialization.
Each value in this array is 16 bits wide and is stored
in big endian format."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.4 (HLOGpsds)
and paragraph 7.5.1.18.8 (HLOGpsus)"
::= { adsl2SCStatusEntry 11 }
adsl2SCStatusQlnMt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of symbols used to measure the Quiet Line Noise
values on the respective transmission direction. This
parameter should correspond to the value specified in the
recommendation (e.g., the number of symbols in 1 second time
interval for G.992.3). This parameter corresponds to 1 second
in loop diagnostic procedure and should be updated in
initialization "
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.19.1 (QLNMTds)
and paragraph 7.5.1.19.3 (QLNMTus)"
::= { adsl2SCStatusEntry 12 }
adsl2SCStatusQlnMt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of symbols used to measure the Quiet Line Noise
values on the respective transmission direction. This
parameter should correspond to the value specified in the
recommendation (e.g., the number of symbols in 1 second time
interval for G.992.3). This parameter corresponds to 1 second
in loop diagnostic procedure and should be updated in
initialization "
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.19.1 (QLNMTds)
and paragraph 7.5.1.19.3 (QLNMTus)"
::= { adsl2SCStatusEntry 12 }
adsl2SCStatusQln OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) UNITS "dBm/Hz"
adsl2SCStatusQln对象类型语法八位字符串（大小（0..512））单位“dBm/Hz”
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of up to 512 real Quiet Line Noise values in dBm/Hz
for the respective transmission direction. It is designed for
up to 512 (downstream) sub-carriers.
The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Each array entry represents the QLN(f = i*Df) value for a
particular sub-carrier index i, (0 <= i < NSC).
The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the
range 0 to 254. A special value n(i)=255 indicates that no
measurement could be done for the subcarrier because it is out
of the passband or that the noise PSD is out of range to be
represented.
This parameter is applicable in loop diagnostic procedure and
initialization. Each value in this array is 8 bits wide."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.19.2 (QLNpsds)
and paragraph 7.5.1.19.4 (QLNpsus)"
::= { adsl2SCStatusEntry 13 }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of up to 512 real Quiet Line Noise values in dBm/Hz
for the respective transmission direction. It is designed for
up to 512 (downstream) sub-carriers.
The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Each array entry represents the QLN(f = i*Df) value for a
particular sub-carrier index i, (0 <= i < NSC).
The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the
range 0 to 254. A special value n(i)=255 indicates that no
measurement could be done for the subcarrier because it is out
of the passband or that the noise PSD is out of range to be
represented.
This parameter is applicable in loop diagnostic procedure and
initialization. Each value in this array is 8 bits wide."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.19.2 (QLNpsds)
and paragraph 7.5.1.19.4 (QLNpsus)"
::= { adsl2SCStatusEntry 13 }
adsl2SCStatusLnAtten OBJECT-TYPE SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "When referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub-carriers during diagnostics mode. When referring to the upstream direction, it is the measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub-carriers during diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.6 (LATNds) and paragraph 7.5.1.7 (LATNus)"
adsl2SCStatusLnAtten对象类型语法无符号32（0..1270 | 2147483646 | 2147483647）单元“0.1 dB”最大访问只读状态当前说明“当参考下游方向时，它是诊断模式期间ATU-C传输的总功率与ATU-R在所有子载波上接收的总功率的测量差值。当参考上游方向时，它是诊断模式期间ATU-R传输的总功率与ATU-C接收的所有子载波总功率之间的测量差值。它的范围从0到1270单位，为0.1 dB（物理值为0到127 dB）。0x7FFFFFFF（2147483647）的特殊值表示线路衰减超出要表示的范围。0x7FFFFFFE（2147483646）的特殊值表示线路衰减测量不可用。此对象反映在关联行上执行的最新增量之后的参数值。DELT过程结束后，参数不再改变，直到删除行或启动新的DELT过程。“参考”ITU-T G.997.1，第7.5.1.6段（LATNds）和第7.5.1.7段（LATNus）”
::= { adsl2SCStatusEntry 14 }
::= { adsl2SCStatusEntry 14 }
adsl2SCStatusSigAtten OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When referring to the downstream direction, it is the measured
difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub-
carriers during Showtime after the diagnostics mode.
When referring to the upstream direction, it is the measured
difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub-
carriers during Showtime after the diagnostics mode.
It ranges from 0 to 1270 units of 0.1 dB (physical values
are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
signal attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
signal attenuation measurement is unavailable.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.8 (SATNds)
and paragraph 7.5.1.9 (SATNus)"
::= { adsl2SCStatusEntry 15 }
adsl2SCStatusSigAtten OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When referring to the downstream direction, it is the measured
difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub-
carriers during Showtime after the diagnostics mode.
When referring to the upstream direction, it is the measured
difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub-
carriers during Showtime after the diagnostics mode.
It ranges from 0 to 1270 units of 0.1 dB (physical values
are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
signal attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
signal attenuation measurement is unavailable.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.8 (SATNds)
and paragraph 7.5.1.9 (SATNus)"
::= { adsl2SCStatusEntry 15 }
adsl2SCStatusSnrMargin OBJECT-TYPE SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the ATU. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB). A special value of 0x7FFFFFFF (2147483647) indicates the SNR Margin is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the SNR Margin measurement is currently unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once
adsl2SCStatusSnrMargin对象类型语法整数32（-640..630 | 2147483646 | 2147483647）单位“0.1 dB”最大访问只读状态当前描述“SNR余量是ATU接收到的噪声功率的最大增量（下游方向ATU-R，上游方向ATU-C），以满足ATU接收的所有承载信道的误码率要求。其范围为0.1 dB的-640到630个单位（物理值为-64到63 dB）。0x7FFFFFFF（2147483647）的特殊值表示SNR裕度超出了要表示的范围。0x7FFFFFFFE（2147483646）的特殊值表示SNR裕度测量当前不可用。此对象反映在关联行上执行的最新增量之后的参数值。一次
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.10 (SNRMds)
and paragraph 7.5.1.11 (SNRMus)"
::= { adsl2SCStatusEntry 16 }
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.10 (SNRMds)
and paragraph 7.5.1.11 (SNRMus)"
::= { adsl2SCStatusEntry 16 }
adsl2SCStatusAttainableRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate. The maximum net data rate
currently attainable by the ATU-C transmitter and ATU-R
receiver (when referring to downstream direction) or by the
ATU-R transmitter and ATU-C receiver (when referring to
upstream direction). Value is coded in bits/second.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.12 (ATTNDRds)
and paragraph 7.5.1.13 (ATTNDRus)"
::= { adsl2SCStatusEntry 17 }
adsl2SCStatusAttainableRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate. The maximum net data rate
currently attainable by the ATU-C transmitter and ATU-R
receiver (when referring to downstream direction) or by the
ATU-R transmitter and ATU-C receiver (when referring to
upstream direction). Value is coded in bits/second.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.12 (ATTNDRds)
and paragraph 7.5.1.13 (ATTNDRus)"
::= { adsl2SCStatusEntry 17 }
adsl2SCStatusActAtp OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Aggregate Transmit Power from the ATU (ATU-R on
downstream direction and ATU-C on upstream direction), at the
instant of measurement. It ranges from -310 to 310 units of
0.1 dB (physical values are -31 to 31 dBm). A value of all
1's indicates the measurement is out of range to be
represented.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.16 (ACTATPds)
and paragraph 7.5.1.17 (ACTATPus)"
::= { adsl2SCStatusEntry 18 }
adsl2SCStatusActAtp OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Aggregate Transmit Power from the ATU (ATU-R on
downstream direction and ATU-C on upstream direction), at the
instant of measurement. It ranges from -310 to 310 units of
0.1 dB (physical values are -31 to 31 dBm). A value of all
1's indicates the measurement is out of range to be
represented.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.16 (ACTATPds)
and paragraph 7.5.1.17 (ACTATPus)"
::= { adsl2SCStatusEntry 18 }
adsl2SCStatusRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create
adsl2SCStatusRowStatus对象类型语法RowStatus MAX-ACCESS读取创建
STATUS current
DESCRIPTION
"Row Status. The manager may create and delete rows
of this table. Please see the description of
adsl2SCStatusTable above for more details."
::= { adsl2SCStatusEntry 19 }
STATUS current
DESCRIPTION
"Row Status. The manager may create and delete rows
of this table. Please see the description of
adsl2SCStatusTable above for more details."
::= { adsl2SCStatusEntry 19 }
------------------------------------------------
-- adsl2LineInventoryTable --
------------------------------------------------
adsl2LineInventoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineInventoryTable contains inventory of the
ADSL2 units."
::= { adsl2Inventory 1 }
------------------------------------------------
-- adsl2LineInventoryTable --
------------------------------------------------
adsl2LineInventoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineInventoryTable contains inventory of the
ADSL2 units."
::= { adsl2Inventory 1 }
adsl2LineInventoryEntry OBJECT-TYPE
SYNTAX Adsl2LineInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineInventoryTable contains inventory of the
ADSL2 units.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238)."
INDEX { ifIndex, adsl2LInvUnit }
::= { adsl2LineInventoryTable 1 }
adsl2LineInventoryEntry OBJECT-TYPE
SYNTAX Adsl2LineInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineInventoryTable contains inventory of the
ADSL2 units.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238)."
INDEX { ifIndex, adsl2LInvUnit }
::= { adsl2LineInventoryTable 1 }
Adsl2LineInventoryEntry ::=
SEQUENCE {
adsl2LInvUnit Adsl2Unit,
adsl2LInvG994VendorId OCTET STRING,
adsl2LInvSystemVendorId OCTET STRING,
adsl2LInvVersionNumber OCTET STRING,
adsl2LInvSerialNumber OCTET STRING,
adsl2LInvSelfTestResult Unsigned32,
adsl2LInvTransmissionCapabilities Adsl2TransmissionModeType
}
Adsl2LineInventoryEntry ::=
SEQUENCE {
adsl2LInvUnit Adsl2Unit,
adsl2LInvG994VendorId OCTET STRING,
adsl2LInvSystemVendorId OCTET STRING,
adsl2LInvVersionNumber OCTET STRING,
adsl2LInvSerialNumber OCTET STRING,
adsl2LInvSelfTestResult Unsigned32,
adsl2LInvTransmissionCapabilities Adsl2TransmissionModeType
}
adsl2LInvUnit OBJECT-TYPE SYNTAX Adsl2Unit MAX-ACCESS not-accessible STATUS current DESCRIPTION "The termination unit atuc(1) or atur(2)."
ADSL2LIVUnit对象类型语法Adsl2Unit MAX-ACCESS不可访问状态当前描述“终端单元atuc（1）或atur（2）”
::= { adsl2LineInventoryEntry 1 }
::= { adsl2LineInventoryEntry 1 }
adsl2LInvG994VendorId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR
message. It consists of 8 binary octets, including a country
code followed by a (regionally allocated) provider code, as
defined in Recommendation T.35."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 2 }
adsl2LInvG994VendorId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR
message. It consists of 8 binary octets, including a country
code followed by a (regionally allocated) provider code, as
defined in Recommendation T.35."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 2 }
adsl2LInvSystemVendorId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU System Vendor ID (identifies the ATU system
integrator) as inserted in the Overhead Messages (both ATUs
for G.992.3 and G.992.4) or in the Embedded Operations
Channel (only ATU-R in G.992.1 and G.992.2). It consists of
8 binary octets, with the same format as used for
Adsl2InvG994VendorId."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 3 }
adsl2LInvSystemVendorId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU System Vendor ID (identifies the ATU system
integrator) as inserted in the Overhead Messages (both ATUs
for G.992.3 and G.992.4) or in the Embedded Operations
Channel (only ATU-R in G.992.1 and G.992.2). It consists of
8 binary octets, with the same format as used for
Adsl2InvG994VendorId."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 3 }
adsl2LInvVersionNumber OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU version number (vendor-specific information) as
inserted in the Overhead Messages (both ATUs for G.992.3 and
G.992.4) or in the Embedded Operations Channel (only ATU-R in
G.992.1 and G.992.2). It consists of up to 16 binary octets."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 4 }
adsl2LInvVersionNumber OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU version number (vendor-specific information) as
inserted in the Overhead Messages (both ATUs for G.992.3 and
G.992.4) or in the Embedded Operations Channel (only ATU-R in
G.992.1 and G.992.2). It consists of up to 16 binary octets."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 4 }
adsl2LInvSerialNumber OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The ATU serial number (vendor-specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in
adsl2LInvSerialNumber对象类型语法八位字节字符串（大小（0..32））MAX-ACCESS只读状态当前描述“插入开销消息（G.992.3和G.992.4的ATU）或嵌入操作通道（仅ATU-R in）中的ATU序列号（供应商特定信息）
G.992.1 and G.992.2). It is vendor-specific information. It
consists of up to 32 ASCII characters."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 5 }
G.992.1 and G.992.2). It is vendor-specific information. It
consists of up to 32 ASCII characters."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 5 }
adsl2LInvSelfTestResult OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU self-test result, coded as a 32-bit value. The
most significant octet of the result is '0' if the self-test
passed, and '1' if the self-test failed. The interpretation
of the other octets is vendor discretionary."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 6 }
adsl2LInvSelfTestResult OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU self-test result, coded as a 32-bit value. The
most significant octet of the result is '0' if the self-test
passed, and '1' if the self-test failed. The interpretation
of the other octets is vendor discretionary."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 6 }
adsl2LInvTransmissionCapabilities OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU transmission system capability list of the different
coding types. It is coded in a bit-map representation with 1
or more bits set. A bit set to '1' means that the ATU
supports the respective coding. The value may be derived
from the handshaking procedures defined in G.994.1. A set
of ADSL2 line transmission modes, with one bit per mode."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 7 }
adsl2LInvTransmissionCapabilities OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU transmission system capability list of the different
coding types. It is coded in a bit-map representation with 1
or more bits set. A bit set to '1' means that the ATU
supports the respective coding. The value may be derived
from the handshaking procedures defined in G.994.1. A set
of ADSL2 line transmission modes, with one bit per mode."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 7 }
------------------------------------------------
-- adsl2LineConfTemplateTable --
------------------------------------------------
adsl2LineConfTemplateTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfTemplateTable contains ADSL2 line
configuration templates.
------------------------------------------------
-- adsl2LineConfTemplateTable --
------------------------------------------------
adsl2LineConfTemplateTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfTemplateTable contains ADSL2 line
configuration templates.
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileLine 1 }
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileLine 1 }
adsl2LineConfTemplateEntry OBJECT-TYPE
adsl2LineConfTemplateEntry对象类型
SYNTAX Adsl2LineConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfTemplateTable contains the ADSL2 line
configuration template.
A default template with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this document."
INDEX { adsl2LConfTempTemplateName }
::= { adsl2LineConfTemplateTable 1 }
SYNTAX Adsl2LineConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfTemplateTable contains the ADSL2 line
configuration template.
A default template with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this document."
INDEX { adsl2LConfTempTemplateName }
::= { adsl2LineConfTemplateTable 1 }
Adsl2LineConfTemplateEntry ::=
SEQUENCE {
adsl2LConfTempTemplateName SnmpAdminString,
adsl2LConfTempLineProfile SnmpAdminString,
adsl2LConfTempChan1ConfProfile SnmpAdminString,
adsl2LConfTempChan1RaRatioDs Unsigned32,
adsl2LConfTempChan1RaRatioUs Unsigned32,
adsl2LConfTempChan2ConfProfile SnmpAdminString,
adsl2LConfTempChan2RaRatioDs Unsigned32,
adsl2LConfTempChan2RaRatioUs Unsigned32,
adsl2LConfTempChan3ConfProfile SnmpAdminString,
adsl2LConfTempChan3RaRatioDs Unsigned32,
adsl2LConfTempChan3RaRatioUs Unsigned32,
adsl2LConfTempChan4ConfProfile SnmpAdminString,
adsl2LConfTempChan4RaRatioDs Unsigned32,
adsl2LConfTempChan4RaRatioUs Unsigned32,
adsl2LConfTempRowStatus RowStatus
}
Adsl2LineConfTemplateEntry ::=
SEQUENCE {
adsl2LConfTempTemplateName SnmpAdminString,
adsl2LConfTempLineProfile SnmpAdminString,
adsl2LConfTempChan1ConfProfile SnmpAdminString,
adsl2LConfTempChan1RaRatioDs Unsigned32,
adsl2LConfTempChan1RaRatioUs Unsigned32,
adsl2LConfTempChan2ConfProfile SnmpAdminString,
adsl2LConfTempChan2RaRatioDs Unsigned32,
adsl2LConfTempChan2RaRatioUs Unsigned32,
adsl2LConfTempChan3ConfProfile SnmpAdminString,
adsl2LConfTempChan3RaRatioDs Unsigned32,
adsl2LConfTempChan3RaRatioUs Unsigned32,
adsl2LConfTempChan4ConfProfile SnmpAdminString,
adsl2LConfTempChan4RaRatioDs Unsigned32,
adsl2LConfTempChan4RaRatioUs Unsigned32,
adsl2LConfTempRowStatus RowStatus
}
adsl2LConfTempTemplateName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
REFERENCE "DSL Forum TR-90, paragraph 5.1.4"
::= { adsl2LineConfTemplateEntry 1 }
adsl2LConfTempTemplateName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
REFERENCE "DSL Forum TR-90, paragraph 5.1.4"
::= { adsl2LineConfTemplateEntry 1 }
adsl2LConfTempLineProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL2 Line Configuration Profile Table, (adsl2LineConfProfTable), which applies for this ADSL2 line."
adsl2LConfTempLineProfile对象类型语法SnmpAdminString（大小（1..32））MAX-ACCESS read create STATUS current DESCRIPTION“此对象的值标识ADSL2线路配置配置文件表（adsl2LineConfProfTable）中适用于此ADSL2线路的行。”
REFERENCE "DSL Forum TR-90, paragraph 5.1.4"
DEFVAL { "DEFVAL" }
::= { adsl2LineConfTemplateEntry 2 }
REFERENCE "DSL Forum TR-90, paragraph 5.1.4"
DEFVAL { "DEFVAL" }
::= { adsl2LineConfTemplateEntry 2 }
adsl2LConfTempChan1ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table,
(adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #1. The channel profile name specified here must
match the name of an existing row in the
adsl2ChConfProfileTable table."
DEFVAL { "DEFVAL" }
::= { adsl2LineConfTemplateEntry 3 }
adsl2LConfTempChan1ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table,
(adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #1. The channel profile name specified here must
match the name of an existing row in the
adsl2ChConfProfileTable table."
DEFVAL { "DEFVAL" }
::= { adsl2LineConfTemplateEntry 3 }
adsl2LConfTempChan1RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #1 when performing rate
adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the 100 -
adsl2LConfTempChan1RaRatioDs is the ratio of excess data
rate to be assigned to all other bearer channels on Downstream
direction. The sum of rate adaptation ratios over all bearers
on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 100 }
::= { adsl2LineConfTemplateEntry 4 }
adsl2LConfTempChan1RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #1 when performing rate
adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the 100 -
adsl2LConfTempChan1RaRatioDs is the ratio of excess data
rate to be assigned to all other bearer channels on Downstream
direction. The sum of rate adaptation ratios over all bearers
on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 100 }
::= { adsl2LineConfTemplateEntry 4 }
adsl2LConfTempChan1RaRatioUs OBJECT-TYPE SYNTAX Unsigned32(0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the
ADSL2ConfTempChan1随机对象类型语法无符号32（0..100）单位“百分比”最大访问读取创建状态当前描述“速率自适应比率。比率（单位%）在上行执行速率自适应时，承载信道#1应考虑到这一点。该比率是指超过最小数据速率的可用数据速率，在所有承载信道上求和。此外
100 - adsl2LConfTempChan1RaRatioUs is the ratio of excess
data rate to be assigned to all other bearer channels on
Upstream direction. The sum of rate adaptation ratios over
all bearers on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 100 }
::= { adsl2LineConfTemplateEntry 5 }
100 - adsl2LConfTempChan1RaRatioUs is the ratio of excess
data rate to be assigned to all other bearer channels on
Upstream direction. The sum of rate adaptation ratios over
all bearers on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 100 }
::= { adsl2LineConfTemplateEntry 5 }
adsl2LConfTempChan2ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #2. If the channel is unused, then the object is set to a zero-length string. This object may be set to a zero-length string only if adsl2LConfTempChan3ConfProfile contains a zero-length string."
adsl2LConfTempChan2ConfProfile对象类型语法SnmpAdminString（大小（0..32））MAX-ACCESS read create STATUS current DESCRIPTION“此对象的值标识ADSL2通道配置配置文件表（ADSL2HConfProfile表）中的行这适用于ADSL2承载信道#2。如果该信道未使用，则该对象设置为零长度字符串。仅当ADSL2ConfTempChan3ConfProfile包含零长度字符串时，该对象才可以设置为零长度字符串。”
DEFVAL { "" }
::= { adsl2LineConfTemplateEntry 6 }
DEFVAL { "" }
::= { adsl2LineConfTemplateEntry 6 }
adsl2LConfTempChan2RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #2 when performing rate
adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the
100 - adsl2LConfTempChan2RaRatioDs is the ratio of excess
data rate to be assigned to all other bearer channels on
Downstream direction. The sum of rate adaptation ratios
over all bearers on the same direction shall be equal to
100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 7 }
adsl2LConfTempChan2RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #2 when performing rate
adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the
100 - adsl2LConfTempChan2RaRatioDs is the ratio of excess
data rate to be assigned to all other bearer channels on
Downstream direction. The sum of rate adaptation ratios
over all bearers on the same direction shall be equal to
100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 7 }
adsl2LConfTempChan2RaRatioUs OBJECT-TYPE SYNTAX Unsigned32(0..100) UNITS "percent"
ADSL2ConfTempChan2随机对象类型语法无符号32（0..100）单位“百分比”
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #2 when performing rate
adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the
100 - adsl2LConfTempChan2RaRatioUs is the ratio of excess
data rate to be assigned to all other bearer channels on
Upstream direction. The sum of rate adaptation ratios over
all bearers on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 8 }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #2 when performing rate
adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the
100 - adsl2LConfTempChan2RaRatioUs is the ratio of excess
data rate to be assigned to all other bearer channels on
Upstream direction. The sum of rate adaptation ratios over
all bearers on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 8 }
adsl2LConfTempChan3ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table
(adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #3. If the channel is unused, then the object is set
to a zero-length string.
This object may be set to a zero-length string only if
adsl2LConfTempChan4ConfProfile contains a zero-length
string.
This object may be set to a non-zero-length string only if
adsl2LConfTempChan2ConfProfile contains a non-zero-length
string."
DEFVAL { "" }
::= { adsl2LineConfTemplateEntry 9 }
adsl2LConfTempChan3ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table
(adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #3. If the channel is unused, then the object is set
to a zero-length string.
This object may be set to a zero-length string only if
adsl2LConfTempChan4ConfProfile contains a zero-length
string.
This object may be set to a non-zero-length string only if
adsl2LConfTempChan2ConfProfile contains a non-zero-length
string."
DEFVAL { "" }
::= { adsl2LineConfTemplateEntry 9 }
adsl2LConfTempChan3RaRatioDs OBJECT-TYPE SYNTAX Unsigned32(0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan3RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream
adsl2conftempchan3raratiods对象类型语法Unsigned32（0..100）单位“百分比”MAX-ACCESS read create STATUS current DESCRIPTION“速率自适应比率。比率（单位：%）在下游执行速率自适应时，承载信道#3应考虑到这一点。该比率是指超过最小数据速率的可用数据速率，在所有承载信道上求和。此外，100-ADSL2ConfTempChan3Raratiods是分配给Dow上所有其他承载信道的多余数据速率的比率流
direction. The sum of rate adaptation ratios over all bearers
on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 10 }
direction. The sum of rate adaptation ratios over all bearers
on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 10 }
adsl2LConfTempChan3RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #3 when performing rate
adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the
100 - adsl2LConfTempChan3RaRatioUs is the ratio of excess
data rate to be assigned to all other bearer channels on
Upstream direction. The sum of rate adaptation ratios over
all bearers on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 11 }
adsl2LConfTempChan3RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #3 when performing rate
adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the
100 - adsl2LConfTempChan3RaRatioUs is the ratio of excess
data rate to be assigned to all other bearer channels on
Upstream direction. The sum of rate adaptation ratios over
all bearers on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 11 }
adsl2LConfTempChan4ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table
(adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #4. If the channel is unused, then the object is set
to a zero-length string.
This object may be set to a non-zero-length string only if
adsl2LConfTempChan3ConfProfile contains a non-zero-length
string."
DEFVAL { "" }
::= { adsl2LineConfTemplateEntry 12 }
adsl2LConfTempChan4ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table
(adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #4. If the channel is unused, then the object is set
to a zero-length string.
This object may be set to a non-zero-length string only if
adsl2LConfTempChan3ConfProfile contains a non-zero-length
string."
DEFVAL { "" }
::= { adsl2LineConfTemplateEntry 12 }
adsl2LConfTempChan4RaRatioDs OBJECT-TYPE SYNTAX Unsigned32(0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "Rate Adaptation Ratio. The ratio (in %) that should be taken
ADSL2ConfTempChan4Raratiods对象类型语法无符号32（0..100）单位“百分比”最大访问读取创建状态当前描述“速率自适应比率。应采用的比率（单位%）
into account for the bearer channel #4 when performing rate
adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the 100 -
adsl2LConfTempChan4RaRatioDs is the ratio of
excess data rate to be assigned to all other bearer channels.
The sum of rate adaptation ratios over all bearers on the same
direction shall sum to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 13 }
into account for the bearer channel #4 when performing rate
adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the 100 -
adsl2LConfTempChan4RaRatioDs is the ratio of
excess data rate to be assigned to all other bearer channels.
The sum of rate adaptation ratios over all bearers on the same
direction shall sum to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 13 }
adsl2LConfTempChan4RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #4 when performing rate
adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over
all bearer channels. Also, the 100 -
adsl2LConfTempChan4RaRatioUs is the
ratio of excess data rate to be assigned to all other bearer
channels. The sum of rate adaptation ratios over all bearers
on the same direction shall sum to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 14 }
adsl2LConfTempChan4RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32(0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #4 when performing rate
adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over
all bearer channels. Also, the 100 -
adsl2LConfTempChan4RaRatioUs is the
ratio of excess data rate to be assigned to all other bearer
channels. The sum of rate adaptation ratios over all bearers
on the same direction shall sum to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 14 }
adsl2LConfTempRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table.
adsl2LConfTempRowStatus对象类型语法RowStatus MAX-ACCESS read create STATUS current DESCRIPTION“此对象用于创建新行或修改或删除此表中的现有行。
A template is activated by setting this object to 'active'. When 'active' is set, the system will validate the template.
通过将此对象设置为“活动”来激活模板。设置“活动”时，系统将验证模板。
Before a template can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
lines."
::= { adsl2LineConfTemplateEntry 15 }
Before a template can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
lines."
::= { adsl2LineConfTemplateEntry 15 }
------------------------------------------
-- adsl2LineConfProfTable --
------------------------------------------
adsl2LineConfProfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfProfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfProfTable contains ADSL2 line profile
configuration.
------------------------------------------
-- adsl2LineConfProfTable --
------------------------------------------
adsl2LineConfProfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfProfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfProfTable contains ADSL2 line profile
configuration.
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileLine 2 }
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileLine 2 }
adsl2LineConfProfEntry OBJECT-TYPE SYNTAX Adsl2LineConfProfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2LineConfProfTable contains ADSL2 line profile configuration.
adsl2LineConfProfEntry对象类型语法adsl2LineConfProfEntry MAX-ACCESS不可访问状态当前描述“表adsl2LineConfProfTable包含ADSL2线路配置文件配置。
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this document."
INDEX { adsl2LConfProfProfileName }
::= { adsl2LineConfProfTable 1 }
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this document."
INDEX { adsl2LConfProfProfileName }
::= { adsl2LineConfProfTable 1 }
Adsl2LineConfProfEntry ::=
SEQUENCE {
adsl2LConfProfProfileName SnmpAdminString,
adsl2LConfProfScMaskDs Adsl2ScMaskDs,
adsl2LConfProfScMaskUs Adsl2ScMaskUs,
adsl2LConfProfRfiBandsDs Adsl2RfiDs,
adsl2LConfProfRaModeDs Adsl2RaMode,
adsl2LConfProfRaModeUs Adsl2RaMode,
adsl2LConfProfRaUsNrmDs Unsigned32,
adsl2LConfProfRaUsNrmUs Unsigned32,
adsl2LConfProfRaUsTimeDs Unsigned32,
adsl2LConfProfRaUsTimeUs Unsigned32,
adsl2LConfProfRaDsNrmsDs Unsigned32,
adsl2LConfProfRaDsNrmsUs Unsigned32,
adsl2LConfProfRaDsTimeDs Unsigned32,
adsl2LConfProfRaDsTimeUs Unsigned32,
adsl2LConfProfTargetSnrmDs Unsigned32,
adsl2LConfProfTargetSnrmUs Unsigned32,
adsl2LConfProfMaxSnrmDs Unsigned32,
Adsl2LineConfProfEntry ::=
SEQUENCE {
adsl2LConfProfProfileName SnmpAdminString,
adsl2LConfProfScMaskDs Adsl2ScMaskDs,
adsl2LConfProfScMaskUs Adsl2ScMaskUs,
adsl2LConfProfRfiBandsDs Adsl2RfiDs,
adsl2LConfProfRaModeDs Adsl2RaMode,
adsl2LConfProfRaModeUs Adsl2RaMode,
adsl2LConfProfRaUsNrmDs Unsigned32,
adsl2LConfProfRaUsNrmUs Unsigned32,
adsl2LConfProfRaUsTimeDs Unsigned32,
adsl2LConfProfRaUsTimeUs Unsigned32,
adsl2LConfProfRaDsNrmsDs Unsigned32,
adsl2LConfProfRaDsNrmsUs Unsigned32,
adsl2LConfProfRaDsTimeDs Unsigned32,
adsl2LConfProfRaDsTimeUs Unsigned32,
adsl2LConfProfTargetSnrmDs Unsigned32,
adsl2LConfProfTargetSnrmUs Unsigned32,
adsl2LConfProfMaxSnrmDs Unsigned32,
adsl2LConfProfMaxSnrmUs Unsigned32, adsl2LConfProfMinSnrmDs Unsigned32, adsl2LConfProfMinSnrmUs Unsigned32, adsl2LConfProfMsgMinUs Unsigned32, adsl2LConfProfMsgMinDs Unsigned32, adsl2LConfProfAtuTransSysEna Adsl2TransmissionModeType, adsl2LConfProfPmMode Adsl2LConfProfPmMode, adsl2LConfProfL0Time Unsigned32, adsl2LConfProfL2Time Unsigned32, adsl2LConfProfL2Atpr Unsigned32, adsl2LConfProfL2Atprt Unsigned32, adsl2LConfProfRowStatus RowStatus }
ADSL2ConfProfMaxSNRMU Unsigned32、ADSL2ConfProfMinsNRMDS Unsigned32、ADSL2ConfProfMinsNRMUS Unsigned32、ADSL2ConfProfMsgMinus Unsigned32、ADSL2ConfProfMsgMinds Unsigned32、ADSL2ConfProfAtutransysena ADSL2TransmissionModelType、ADSL2ConfProfMode ADSL2ConfProfPMMode、ADSL2ConfProfL0时间Unsigned32、ADSL2ConfProfProfTime Unsigned32、，ADSL2ConfProfL2ATPR Unsigned32，ADSL2ConfProfL2ATPR Unsigned32，ADSL2ConfProfRowStatus RowStatus}
adsl2LConfProfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2LineConfProfEntry 1 }
adsl2LConfProfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2LineConfProfEntry 1 }
adsl2LConfProfScMaskDs OBJECT-TYPE
SYNTAX Adsl2ScMaskDs
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Sub-carriers mask. A bitmap of 512 bits that allows masking
up to 512 downstream sub-carriers, depending on NSCds. If bit
i (0 <= i < NSCds) is set to '1', the respective
downstream sub-carrier i is masked, and if set to '0', the
respective sub-carrier is unmasked. Note that there should
always be unmasked sub-carriers (i.e., the object cannot be
all 1's). Also note that if NSCds < 512, all bits
i (NSCds < i <= 512) should be set to '1'."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.6"
::= { adsl2LineConfProfEntry 2 }
adsl2LConfProfScMaskDs OBJECT-TYPE
SYNTAX Adsl2ScMaskDs
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Sub-carriers mask. A bitmap of 512 bits that allows masking
up to 512 downstream sub-carriers, depending on NSCds. If bit
i (0 <= i < NSCds) is set to '1', the respective
downstream sub-carrier i is masked, and if set to '0', the
respective sub-carrier is unmasked. Note that there should
always be unmasked sub-carriers (i.e., the object cannot be
all 1's). Also note that if NSCds < 512, all bits
i (NSCds < i <= 512) should be set to '1'."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.6"
::= { adsl2LineConfProfEntry 2 }
adsl2LConfProfScMaskUs OBJECT-TYPE SYNTAX Adsl2ScMaskUs MAX-ACCESS read-create STATUS current DESCRIPTION "Sub-carriers mask. A bitmap of 64 bits that allows masking up to 64 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCus) is set to '1', the respective upstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there
adsl2LConfProfScMaskUs对象类型语法Adsl2ScMaskUs MAX-ACCESS read create STATUS current DESCRIPTION“子载波掩码。一种64位位图，允许屏蔽多达64个下游子载波，具体取决于NSCD。如果位i（0<=i<NSCus）设置为“1”，相应的上游子载波i被屏蔽，如果设置为“0”，则相应的子载波被解除屏蔽。注意
should always be unmasked sub-carriers (i.e., the object
cannot be all 1's). Also note that if NSCus <
64, all bits i (NSCus < i <= 64) should be set to '1'."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.7"
::= { adsl2LineConfProfEntry 3 }
should always be unmasked sub-carriers (i.e., the object
cannot be all 1's). Also note that if NSCus <
64, all bits i (NSCus < i <= 64) should be set to '1'."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.7"
::= { adsl2LineConfProfEntry 3 }
adsl2LConfProfRfiBandsDs OBJECT-TYPE
SYNTAX Adsl2RfiDs
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The subset of downstream PSD mask breakpoints that shall be
used to notch an RFI band.
The specific interpolation around these points is defined in
G.992.5. It is a bitmap of 512 bits that allows referring to
up to 512 downstream sub-carriers, depending on NSCds. If bit
i (0 <= i < NSCds) is set to '1', the respective downstream
sub-carrier i is part of a notch filter, and if set to '0',
the respective sub-carrier is not part of a notch filter.
This information complements the specification provided by
adsl2LConfProfPsdMaskDs.
Note that if NSCds < 512, all bits i (NSCds<i<512)
should be set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.9"
::= { adsl2LineConfProfEntry 4 }
adsl2LConfProfRfiBandsDs OBJECT-TYPE
SYNTAX Adsl2RfiDs
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The subset of downstream PSD mask breakpoints that shall be
used to notch an RFI band.
The specific interpolation around these points is defined in
G.992.5. It is a bitmap of 512 bits that allows referring to
up to 512 downstream sub-carriers, depending on NSCds. If bit
i (0 <= i < NSCds) is set to '1', the respective downstream
sub-carrier i is part of a notch filter, and if set to '0',
the respective sub-carrier is not part of a notch filter.
This information complements the specification provided by
adsl2LConfProfPsdMaskDs.
Note that if NSCds < 512, all bits i (NSCds<i<512)
should be set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.9"
::= { adsl2LineConfProfEntry 4 }
adsl2LConfProfRaModeDs OBJECT-TYPE
SYNTAX Adsl2RaMode
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The mode of operation of a rate-adaptive ATU-C in the transmit
direction. The parameter can take three values:
manual(1),
raInit(2), or
dynamicRa(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.1"
DEFVAL { manual }
::= { adsl2LineConfProfEntry 5 }
adsl2LConfProfRaModeDs OBJECT-TYPE
SYNTAX Adsl2RaMode
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The mode of operation of a rate-adaptive ATU-C in the transmit
direction. The parameter can take three values:
manual(1),
raInit(2), or
dynamicRa(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.1"
DEFVAL { manual }
::= { adsl2LineConfProfEntry 5 }
adsl2LConfProfRaModeUs OBJECT-TYPE SYNTAX Adsl2RaMode MAX-ACCESS read-create STATUS current DESCRIPTION "The mode of operation of a rate-adaptive ATU-R in the transmit direction. The parameter can take three values: manual(1),
adsl2LConfProfRaModeUs对象类型语法Adsl2RaMode MAX-ACCESS read create STATUS current DESCRIPTION“传输方向上速率自适应ATU-R的操作模式。该参数可采用三个值：手动（1），
raInit(2), or
dynamicRa(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.2"
DEFVAL { manual }
::= { adsl2LineConfProfEntry 6 }
raInit(2), or
dynamicRa(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.2"
DEFVAL { manual }
::= { adsl2LineConfProfEntry 6 }
adsl2LConfProfRaUsNrmDs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Downstream Up-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream
noise margin is above this value and stays above it for
more than the time specified by the adsl2LConfProfRaUsTimeDs,
the ATU-R shall attempt to increase the downstream net data
rate. The Downstream Up-Shift Noise Margin ranges from 0 to
310 units of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.3"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 7 }
adsl2LConfProfRaUsNrmDs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Downstream Up-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream
noise margin is above this value and stays above it for
more than the time specified by the adsl2LConfProfRaUsTimeDs,
the ATU-R shall attempt to increase the downstream net data
rate. The Downstream Up-Shift Noise Margin ranges from 0 to
310 units of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.3"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 7 }
adsl2LConfProfRaUsNrmUs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Upstream Up-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream
noise margin is above this value and stays above it for more
than the time specified by the adsl2LConfProfRaUsTimeUs, the
ATU-C shall attempt to increase the upstream net data rate.
The Upstream Up-Shift Noise Margin ranges from 0 to 310 units
of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.4"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 8 }
adsl2LConfProfRaUsNrmUs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Upstream Up-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream
noise margin is above this value and stays above it for more
than the time specified by the adsl2LConfProfRaUsTimeUs, the
ATU-C shall attempt to increase the upstream net data rate.
The Upstream Up-Shift Noise Margin ranges from 0 to 310 units
of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.4"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 8 }
adsl2LConfProfRaUsTimeDs OBJECT-TYPE SYNTAX Unsigned32(0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The Downstream Up-Shift Time Interval, to be used when adsl2LConfProfRaModeDs is set to dynamicRa. The interval of
ADSL2LConfProfRastimeds对象类型语法Unsigned32（0..16383）单位“秒”最大访问读取创建状态当前描述“下游上移时间间隔，当ADSL2LConfProfRaModes设置为dynamicRa时使用。的间隔
time that the downstream noise margin should stay above the
Downstream Up-Shift Noise Margin before the ATU-R shall
attempt to increase the downstream net data rate. The time
interval ranges from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.5"
DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 9 }
time that the downstream noise margin should stay above the
Downstream Up-Shift Noise Margin before the ATU-R shall
attempt to increase the downstream net data rate. The time
interval ranges from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.5"
DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 9 }
adsl2LConfProfRaUsTimeUs OBJECT-TYPE
SYNTAX Unsigned32(0..16383)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Upstream Up-Shift Time Interval, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. The interval of
time the upstream noise margin should stay above the
Upstream Up-Shift Noise Margin before the ATU-C shall
attempt to increase the upstream net data rate. The time
interval ranges from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.6"
DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 10 }
adsl2LConfProfRaUsTimeUs OBJECT-TYPE
SYNTAX Unsigned32(0..16383)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Upstream Up-Shift Time Interval, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. The interval of
time the upstream noise margin should stay above the
Upstream Up-Shift Noise Margin before the ATU-C shall
attempt to increase the upstream net data rate. The time
interval ranges from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.6"
DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 10 }
adsl2LConfProfRaDsNrmsDs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Downstream Down-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream
noise margin is below this value and stays below that for more
than the time specified by the adsl2LConfProfRaDsTimeDs, the
ATU-R shall attempt to decrease the downstream net data rate.
The Downstream Down-Shift Noise Margin ranges from 0 to 310
units of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.7"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 11 }
adsl2LConfProfRaDsNrmsDs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Downstream Down-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream
noise margin is below this value and stays below that for more
than the time specified by the adsl2LConfProfRaDsTimeDs, the
ATU-R shall attempt to decrease the downstream net data rate.
The Downstream Down-Shift Noise Margin ranges from 0 to 310
units of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.7"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 11 }
adsl2LConfProfRaDsNrmsUs OBJECT-TYPE SYNTAX Unsigned32(0..310) UNITS "0.1 dB" MAX-ACCESS read-create STATUS current DESCRIPTION "The Upstream Down-Shift Noise Margin value, to be used when
adsl2LConfProfRaDsNrmsUs对象类型语法无符号32（0..310）单元“0.1 dB”最大访问读取创建状态当前描述“上游下移噪声裕度值，在
adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream
noise margin is below this value and stays below that for more
than the time specified by the adsl2LConfProfRaDsTimeUs, the
ATU-C shall attempt to decrease the upstream net data rate.
The Upstream Down-Shift Noise Margin ranges from 0 to 310
units of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.8"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 12 }
adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream
noise margin is below this value and stays below that for more
than the time specified by the adsl2LConfProfRaDsTimeUs, the
ATU-C shall attempt to decrease the upstream net data rate.
The Upstream Down-Shift Noise Margin ranges from 0 to 310
units of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.8"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 12 }
adsl2LConfProfRaDsTimeDs OBJECT-TYPE
SYNTAX Unsigned32(0..16383)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Downstream Down-Shift Time Interval, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. The interval of
time the downstream noise margin should stay below the
Downstream Down-Shift Noise Margin before the ATU-R shall
attempt to decrease the downstream net data rate. The time
interval ranges from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.9"
DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 13 }
adsl2LConfProfRaDsTimeDs OBJECT-TYPE
SYNTAX Unsigned32(0..16383)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Downstream Down-Shift Time Interval, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. The interval of
time the downstream noise margin should stay below the
Downstream Down-Shift Noise Margin before the ATU-R shall
attempt to decrease the downstream net data rate. The time
interval ranges from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.9"
DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 13 }
adsl2LConfProfRaDsTimeUs OBJECT-TYPE
SYNTAX Unsigned32(0..16383)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Upstream Down-Shift Time Interval, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. The interval of
time the upstream noise margin should stay below the Upstream
Down-Shift Noise Margin before the ATU-C shall attempt to
decrease the upstream net data rate. The time interval ranges
from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.10"
DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 14 }
adsl2LConfProfRaDsTimeUs OBJECT-TYPE
SYNTAX Unsigned32(0..16383)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Upstream Down-Shift Time Interval, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. The interval of
time the upstream noise margin should stay below the Upstream
Down-Shift Noise Margin before the ATU-C shall attempt to
decrease the upstream net data rate. The time interval ranges
from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.10"
DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 14 }
adsl2LConfProfTargetSnrmDs OBJECT-TYPE SYNTAX Unsigned32(0..310) UNITS "0.1 dB" MAX-ACCESS read-create STATUS current DESCRIPTION
adsl2LConfProfTargetSnrmDs对象类型语法无符号32（0..310）单元“0.1 dB”最大读取创建状态当前说明
"The minimum Noise Margin the ATU-R receiver shall achieve,
relative to the BER requirement for each of the downstream
bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB
(physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.1"
DEFVAL { 60 }
::= { adsl2LineConfProfEntry 15 }
"The minimum Noise Margin the ATU-R receiver shall achieve,
relative to the BER requirement for each of the downstream
bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB
(physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.1"
DEFVAL { 60 }
::= { adsl2LineConfProfEntry 15 }
adsl2LConfProfTargetSnrmUs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum Noise Margin the ATU-C receiver shall achieve,
relative to the BER requirement for each of the upstream
bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB
(physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.2"
DEFVAL { 60 }
::= { adsl2LineConfProfEntry 16 }
adsl2LConfProfTargetSnrmUs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum Noise Margin the ATU-C receiver shall achieve,
relative to the BER requirement for each of the upstream
bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB
(physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.2"
DEFVAL { 60 }
::= { adsl2LineConfProfEntry 16 }
adsl2LConfProfMaxSnrmDs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum Noise Margin the ATU-R receiver shall try to
sustain. If the Noise Margin is above this level, the ATU-R
shall request that the ATU-C reduce the ATU-C transmit power
to get a noise margin below this limit (if this functionality
is supported). The maximum noise margin ranges from 0 to 310
units of 0.1 dB (physical values are 0 to 31 dB). A value of
0x7FFFFFFF (2147483647) means that there is no maximum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.3"
DEFVAL { 310 }
::= { adsl2LineConfProfEntry 17 }
adsl2LConfProfMaxSnrmDs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum Noise Margin the ATU-R receiver shall try to
sustain. If the Noise Margin is above this level, the ATU-R
shall request that the ATU-C reduce the ATU-C transmit power
to get a noise margin below this limit (if this functionality
is supported). The maximum noise margin ranges from 0 to 310
units of 0.1 dB (physical values are 0 to 31 dB). A value of
0x7FFFFFFF (2147483647) means that there is no maximum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.3"
DEFVAL { 310 }
::= { adsl2LineConfProfEntry 17 }
adsl2LConfProfMaxSnrmUs OBJECT-TYPE SYNTAX Unsigned32 (0..310 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum Noise Margin the ATU-C receiver shall try to
adsl2LConfProfMaxSnrmUs对象类型语法无符号32（0..310 | 2147483647）单位“0.1 dB”最大访问读取创建状态当前描述ATU-C接收器应尝试的最大噪声容限
sustain. If the Noise Margin is above this level, the ATU-C
shall request that the ATU-R reduce the ATU-R transmit power
to get a noise margin below this limit (if this functionality
is supported). The maximum noise margin ranges from 0 to 310
units of 0.1 dB (physical values are 0 to 31 dB). A value of
0x7FFFFFFF (2147483647) means that there is no maximum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.4"
DEFVAL { 310 }
::= { adsl2LineConfProfEntry 18 }
sustain. If the Noise Margin is above this level, the ATU-C
shall request that the ATU-R reduce the ATU-R transmit power
to get a noise margin below this limit (if this functionality
is supported). The maximum noise margin ranges from 0 to 310
units of 0.1 dB (physical values are 0 to 31 dB). A value of
0x7FFFFFFF (2147483647) means that there is no maximum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.4"
DEFVAL { 310 }
::= { adsl2LineConfProfEntry 18 }
adsl2LConfProfMinSnrmDs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum Noise Margin the ATU-R receiver shall tolerate.
If the noise margin falls below this level, the ATU-R shall
request that the ATU-C increase the ATU-C transmit power.
If an increase to ATU-C transmit power is not possible, a
loss-of-margin (LOM) defect occurs, the ATU-R shall fail and
attempt to reinitialize, and the NMS shall be notified. The
minimum noise margin ranges from 0 to 310 units of
0.1 dB (physical values are 0 to 31 dB). A value of 0 means
that there is no minimum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.5"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 19 }
adsl2LConfProfMinSnrmDs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum Noise Margin the ATU-R receiver shall tolerate.
If the noise margin falls below this level, the ATU-R shall
request that the ATU-C increase the ATU-C transmit power.
If an increase to ATU-C transmit power is not possible, a
loss-of-margin (LOM) defect occurs, the ATU-R shall fail and
attempt to reinitialize, and the NMS shall be notified. The
minimum noise margin ranges from 0 to 310 units of
0.1 dB (physical values are 0 to 31 dB). A value of 0 means
that there is no minimum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.5"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 19 }
adsl2LConfProfMinSnrmUs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum Noise Margin the ATU-C receiver shall tolerate.
If the noise margin falls below this level, the ATU-C shall
request that the ATU-R increase the ATU-R transmit power.
If an increase of ATU-R transmit power is not possible, a
loss-of-margin (LOM) defect occurs, the ATU-C shall fail and
attempt to reinitialize, and the NMS shall be notified. The
minimum noise margin ranges from 0 to 310 units of
0.1 dB (physical values are 0 to 31 dB). A value of 0 means
that there is no minimum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.6"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 20 }
adsl2LConfProfMinSnrmUs OBJECT-TYPE
SYNTAX Unsigned32(0..310)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum Noise Margin the ATU-C receiver shall tolerate.
If the noise margin falls below this level, the ATU-C shall
request that the ATU-R increase the ATU-R transmit power.
If an increase of ATU-R transmit power is not possible, a
loss-of-margin (LOM) defect occurs, the ATU-C shall fail and
attempt to reinitialize, and the NMS shall be notified. The
minimum noise margin ranges from 0 to 310 units of
0.1 dB (physical values are 0 to 31 dB). A value of 0 means
that there is no minimum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.6"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 20 }
adsl2LConfProfMsgMinUs OBJECT-TYPE
SYNTAX Unsigned32(4000..63000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Overhead Rate Upstream. Defines the minimum rate of
the message-based overhead that shall be maintained by the ATU
in upstream direction. Expressed in bits per second and
ranges from 4000 to 63000 bps."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.5.1"
DEFVAL { 4000 }
::= { adsl2LineConfProfEntry 21 }
adsl2LConfProfMsgMinUs OBJECT-TYPE
SYNTAX Unsigned32(4000..63000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Overhead Rate Upstream. Defines the minimum rate of
the message-based overhead that shall be maintained by the ATU
in upstream direction. Expressed in bits per second and
ranges from 4000 to 63000 bps."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.5.1"
DEFVAL { 4000 }
::= { adsl2LineConfProfEntry 21 }
adsl2LConfProfMsgMinDs OBJECT-TYPE
SYNTAX Unsigned32(4000..63000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Overhead Rate Downstream. Defines the minimum rate of
the message-based overhead that shall be maintained by the ATU
in downstream direction. Expressed in bits per second and
ranges from 4000 to 63000 bps."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.5.2"
DEFVAL { 4000 }
::= { adsl2LineConfProfEntry 22 }
adsl2LConfProfMsgMinDs OBJECT-TYPE
SYNTAX Unsigned32(4000..63000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Overhead Rate Downstream. Defines the minimum rate of
the message-based overhead that shall be maintained by the ATU
in downstream direction. Expressed in bits per second and
ranges from 4000 to 63000 bps."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.5.2"
DEFVAL { 4000 }
::= { adsl2LineConfProfEntry 22 }
adsl2LConfProfAtuTransSysEna OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"ATU Transmission System Enabling (ATSE). A list of the
different coding types enabled in this profile. It is coded
in a bit-map representation with 1 or more bits set. A bit
set to '1' means that the ATUs may apply the respective
coding for the ADSL line. A bit set to '0' means that
the ATUs cannot apply the respective coding for the ADSL
line. All 'reserved' bits should be set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.1"
::= { adsl2LineConfProfEntry 23 }
adsl2LConfProfAtuTransSysEna OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"ATU Transmission System Enabling (ATSE). A list of the
different coding types enabled in this profile. It is coded
in a bit-map representation with 1 or more bits set. A bit
set to '1' means that the ATUs may apply the respective
coding for the ADSL line. A bit set to '0' means that
the ATUs cannot apply the respective coding for the ADSL
line. All 'reserved' bits should be set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.1"
::= { adsl2LineConfProfEntry 23 }
adsl2LConfProfPmMode OBJECT-TYPE SYNTAX Adsl2LConfProfPmMode MAX-ACCESS read-create STATUS current DESCRIPTION
adsl2LConfProfPmMode对象类型语法adsl2LConfProfPmMode MAX-ACCESS读取创建状态当前说明
"Power management state Enabling. Defines the power states the
ATU-C or ATU-R may autonomously transition to on this line.
The various bit positions are: allowTransitionsToIdle(0) and
allowTransitionsToLowPower(1). A bit with a '1' value means
that the ATU is allowed to transit into the respective state,
and a '0' value means that the ATU is not allowed
to transit into the respective state."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.4"
DEFVAL { { allowTransitionsToIdle, allowTransitionsToLowPower } }
::= { adsl2LineConfProfEntry 24 }
"Power management state Enabling. Defines the power states the
ATU-C or ATU-R may autonomously transition to on this line.
The various bit positions are: allowTransitionsToIdle(0) and
allowTransitionsToLowPower(1). A bit with a '1' value means
that the ATU is allowed to transit into the respective state,
and a '0' value means that the ATU is not allowed
to transit into the respective state."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.4"
DEFVAL { { allowTransitionsToIdle, allowTransitionsToLowPower } }
::= { adsl2LineConfProfEntry 24 }
adsl2LConfProfL0Time OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This minimum time (in seconds) between an Exit from the L2
state and the next Entry into the L2 state. It ranges from 0
to 255 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.5"
DEFVAL { 255 }
::= { adsl2LineConfProfEntry 25 }
adsl2LConfProfL0Time OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This minimum time (in seconds) between an Exit from the L2
state and the next Entry into the L2 state. It ranges from 0
to 255 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.5"
DEFVAL { 255 }
::= { adsl2LineConfProfEntry 25 }
adsl2LConfProfL2Time OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This minimum time (in seconds) between an Entry into the
L2 state and the first Power Trim in the L2 state and between
two consecutive Power Trims in the L2 State.
It ranges from 0 to 255 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.6"
DEFVAL { 255 }
::= { adsl2LineConfProfEntry 26 }
adsl2LConfProfL2Time OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This minimum time (in seconds) between an Entry into the
L2 state and the first Power Trim in the L2 state and between
two consecutive Power Trims in the L2 State.
It ranges from 0 to 255 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.6"
DEFVAL { 255 }
::= { adsl2LineConfProfEntry 26 }
adsl2LConfProfL2Atpr OBJECT-TYPE SYNTAX Unsigned32 (0..31) UNITS "dB" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It ranges from 0 dB to 31 dB."
adsl2LConfProfL2Atpr对象类型语法Unsigned32（0..31）单元“dB”MAX-ACCESS read create STATUS current DESCRIPTION“在L0状态转换到L2状态时或通过L2状态中的单个功率微调可执行的最大聚合发射功率降低（以dB为单位）。其范围为0 dB到31 dB。”
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.1.7"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 27 }
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.1.7"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 27 }
adsl2LConfProfL2Atprt OBJECT-TYPE
SYNTAX Unsigned32 (0..31)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The total maximum aggregate transmit power reduction
(in dB) that can be performed in an L2 state. This is the
sum of all reductions of L2 Request (i.e., at transition of
L0 to L2 state) and Power Trims."
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.1.9"
DEFVAL { 31 }
::= { adsl2LineConfProfEntry 28 }
adsl2LConfProfL2Atprt OBJECT-TYPE
SYNTAX Unsigned32 (0..31)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The total maximum aggregate transmit power reduction
(in dB) that can be performed in an L2 state. This is the
sum of all reductions of L2 Request (i.e., at transition of
L0 to L2 state) and Power Trims."
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.1.9"
DEFVAL { 31 }
::= { adsl2LineConfProfEntry 28 }
adsl2LConfProfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table.
adsl2LConfProfRowStatus对象类型语法RowStatus MAX-ACCESS read create STATUS current DESCRIPTION“此对象用于创建新行或修改或删除此表中的现有行。
A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile.
通过将此对象设置为“活动”来激活配置文件。设置“激活”时，系统将验证配置文件。
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2LineConfProfEntry 29 }
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2LineConfProfEntry 29 }
------------------------------------------
-- adsl2LineConfProfModeSpecTable --
------------------------------------------
adsl2LineConfProfModeSpecTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfProfModeSpecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfProfModeSpecTable extends the
ADSL2 line configuration profile by ADSL Mode Specific
parameters.
A row in this table that has an index of
------------------------------------------
-- adsl2LineConfProfModeSpecTable --
------------------------------------------
adsl2LineConfProfModeSpecTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfProfModeSpecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfProfModeSpecTable extends the
ADSL2 line configuration profile by ADSL Mode Specific
parameters.
A row in this table that has an index of
adsl2LConfProfAdslMode == defMode(1) is called a 'mandatory' row. A row in this table that has an index such that adsl2LConfProfAdslMode is not equal to defMode(1) is called an 'optional' row. When a row in the adsl2LineConfProfTable table (the parent row) is created, the SNMP agent will automatically create a 'mandatory' row in this table. When the parent row is deleted, the SNMP agent will automatically delete all associated rows in this table. Any attempt to delete the 'mandatory' row using the adsl2LConfProfModeSpecRowStatus attribute will be rejected by the SNMP agent. The manager MAY create an 'optional' row in this table using the adsl2LConfProfModeSpecRowStatus attribute if the parent row exists. The manager MAY delete an 'optional' row in this table using the adsl2LConfProfModeSpecRowStatus attribute at any time. If the actual transmission mode of a DSL line does not match one of the 'optional' rows in this table, then the line will use the PSD configuration from the 'mandatory' row.
adsl2LConfProfAdslMode==defMode（1）被称为“强制”行。此表中的某一行的索引使adsl2LConfProfAdslMode不等于defMode（1），则该行称为“可选”行。在adsl2LineConfProfTable表（父行）中创建行时，SNMP代理将自动在此表中创建“强制”行。删除父行时，SNMP代理将自动删除此表中的所有关联行。SNMP代理将拒绝使用adsl2LConfProfModeSpecRowStatus属性删除“强制”行的任何尝试。如果父行存在，管理器可以使用adsl2LConfProfModeSpecRowStatus属性在此表中创建“可选”行。管理器可以随时使用adsl2LConfProfModeSpecRowStatus属性删除此表中的“可选”行。如果DSL线路的实际传输模式与本表中的“可选”行之一不匹配，则该线路将使用“强制性”行中的PSD配置。
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileLine 3 }
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileLine 3 }
adsl2LineConfProfModeSpecEntry OBJECT-TYPE
SYNTAX Adsl2LineConfProfModeSpecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfProfModeSpecTable extends the
ADSL2 line configuration profile by ADSL Mode Specific
parameters."
INDEX { adsl2LConfProfProfileName, adsl2LConfProfAdslMode }
::= { adsl2LineConfProfModeSpecTable 1 }
adsl2LineConfProfModeSpecEntry OBJECT-TYPE
SYNTAX Adsl2LineConfProfModeSpecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfProfModeSpecTable extends the
ADSL2 line configuration profile by ADSL Mode Specific
parameters."
INDEX { adsl2LConfProfProfileName, adsl2LConfProfAdslMode }
::= { adsl2LineConfProfModeSpecTable 1 }
Adsl2LineConfProfModeSpecEntry ::=
SEQUENCE {
adsl2LConfProfAdslMode Adsl2OperationModes,
adsl2LConfProfMaxNomPsdDs Integer32,
adsl2LConfProfMaxNomPsdUs Integer32,
adsl2LConfProfMaxNomAtpDs Unsigned32,
adsl2LConfProfMaxNomAtpUs Unsigned32,
adsl2LConfProfMaxAggRxPwrUs Integer32,
adsl2LConfProfPsdMaskDs Adsl2PsdMaskDs,
Adsl2LineConfProfModeSpecEntry ::=
SEQUENCE {
adsl2LConfProfAdslMode Adsl2OperationModes,
adsl2LConfProfMaxNomPsdDs Integer32,
adsl2LConfProfMaxNomPsdUs Integer32,
adsl2LConfProfMaxNomAtpDs Unsigned32,
adsl2LConfProfMaxNomAtpUs Unsigned32,
adsl2LConfProfMaxAggRxPwrUs Integer32,
adsl2LConfProfPsdMaskDs Adsl2PsdMaskDs,
adsl2LConfProfPsdMaskUs Adsl2PsdMaskUs, adsl2LConfProfPsdMaskSelectUs Unsigned32, adsl2LConfProfModeSpecRowStatus RowStatus }
adsl2LConfProfPsdMaskUs Adsl2PsdMaskUs，adsl2LConfProfPsdMaskSelectUs Unsigned32，ADSL2LConfProfModesSpecRowStatus行状态}
adsl2LConfProfAdslMode OBJECT-TYPE
SYNTAX Adsl2OperationModes
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ADSL Mode is a way of categorizing the various ADSL
transmission modes into groups; each group (ADSL Mode) shares
the same PSD configuration.
There should be multiple entries in this table for a given
line profile in case multiple bits are set in
adsl2LConfProfAtuTransSysEna for that profile."
REFERENCE "DSL Forum TR-90, paragraph 5.1.8"
::= { adsl2LineConfProfModeSpecEntry 1 }
adsl2LConfProfAdslMode OBJECT-TYPE
SYNTAX Adsl2OperationModes
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ADSL Mode is a way of categorizing the various ADSL
transmission modes into groups; each group (ADSL Mode) shares
the same PSD configuration.
There should be multiple entries in this table for a given
line profile in case multiple bits are set in
adsl2LConfProfAtuTransSysEna for that profile."
REFERENCE "DSL Forum TR-90, paragraph 5.1.8"
::= { adsl2LineConfProfModeSpecEntry 1 }
adsl2LConfProfMaxNomPsdDs OBJECT-TYPE
SYNTAX Integer32(-600..-300)
UNITS "0.1 dBm/Hz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum nominal transmit PSD in the downstream
direction during initialization and Showtime. It ranges from
-600 to -300 units of 0.1 dBm/Hz (physical values are -60 to
-30 dBm/Hz)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { -300 }
::= { adsl2LineConfProfModeSpecEntry 2 }
adsl2LConfProfMaxNomPsdDs OBJECT-TYPE
SYNTAX Integer32(-600..-300)
UNITS "0.1 dBm/Hz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum nominal transmit PSD in the downstream
direction during initialization and Showtime. It ranges from
-600 to -300 units of 0.1 dBm/Hz (physical values are -60 to
-30 dBm/Hz)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { -300 }
::= { adsl2LineConfProfModeSpecEntry 2 }
adsl2LConfProfMaxNomPsdUs OBJECT-TYPE
SYNTAX Integer32(-600..-300)
UNITS "0.1 dBm/Hz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum nominal transmit PSD in the upstream direction
during initialization and Showtime. It ranges from -600 to
-300 units of 0.1 dBm/Hz (physical values are -60 to
-30 dBm/Hz)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { -300 }
::= { adsl2LineConfProfModeSpecEntry 3 }
adsl2LConfProfMaxNomPsdUs OBJECT-TYPE
SYNTAX Integer32(-600..-300)
UNITS "0.1 dBm/Hz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum nominal transmit PSD in the upstream direction
during initialization and Showtime. It ranges from -600 to
-300 units of 0.1 dBm/Hz (physical values are -60 to
-30 dBm/Hz)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { -300 }
::= { adsl2LineConfProfModeSpecEntry 3 }
adsl2LConfProfMaxNomAtpDs OBJECT-TYPE
adsl2LConfProfMaxNomAtpDs对象类型
SYNTAX Unsigned32 (0..255)
UNITS "0.1 dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum nominal aggregate transmit power in the
downstream direction during initialization and Showtime. It
ranges from 0 to 255 units of 0.1 dBm (physical values are 0
to 25.5 dBm)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { 255 }
::= { adsl2LineConfProfModeSpecEntry 4 }
SYNTAX Unsigned32 (0..255)
UNITS "0.1 dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum nominal aggregate transmit power in the
downstream direction during initialization and Showtime. It
ranges from 0 to 255 units of 0.1 dBm (physical values are 0
to 25.5 dBm)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { 255 }
::= { adsl2LineConfProfModeSpecEntry 4 }
adsl2LConfProfMaxNomAtpUs OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "0.1 dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum nominal aggregate transmit power in the upstream
direction during initialization and Showtime. It ranges from
0 to 255 units of 0.1 dBm (physical values are 0 to 25.5
dBm)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { 255 }
::= { adsl2LineConfProfModeSpecEntry 5 }
adsl2LConfProfMaxNomAtpUs OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "0.1 dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum nominal aggregate transmit power in the upstream
direction during initialization and Showtime. It ranges from
0 to 255 units of 0.1 dBm (physical values are 0 to 25.5
dBm)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { 255 }
::= { adsl2LineConfProfModeSpecEntry 5 }
adsl2LConfProfMaxAggRxPwrUs OBJECT-TYPE
SYNTAX Integer32(-255..255 | 2147483647)
UNITS "0.1 dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum upstream aggregate receive power over the relevant
set of sub-carriers. The ATU-C should verify that the
upstream power cutback is such that this maximum aggregate
receive power value is honored. It ranges from -255 to 255
units of 0.1 dBm (physical values are -25.5 to 25.5 dBm).
A value of 0x7FFFFFFF (2147483647) means that there is no
limit."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { 255 }
::= { adsl2LineConfProfModeSpecEntry 6 }
adsl2LConfProfMaxAggRxPwrUs OBJECT-TYPE
SYNTAX Integer32(-255..255 | 2147483647)
UNITS "0.1 dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum upstream aggregate receive power over the relevant
set of sub-carriers. The ATU-C should verify that the
upstream power cutback is such that this maximum aggregate
receive power value is honored. It ranges from -255 to 255
units of 0.1 dBm (physical values are -25.5 to 25.5 dBm).
A value of 0x7FFFFFFF (2147483647) means that there is no
limit."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { 255 }
::= { adsl2LineConfProfModeSpecEntry 6 }
adsl2LConfProfPsdMaskDs OBJECT-TYPE SYNTAX Adsl2PsdMaskDs MAX-ACCESS read-create STATUS current
adsl2LConfProfPsdMaskDs对象类型语法Adsl2PsdMaskDs MAX-ACCESS read create STATUS current
DESCRIPTION
"The downstream PSD mask applicable at the U-C2 reference
point.
This parameter is used only for G.992.5, and it may impose PSD
restrictions (breakpoints) in addition to the Limit PSD mask
defined in G.992.5.
This is a string of 32 pairs of values in the following
structure:
Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 94-95, which are
associated with a 32nd breakpoint.
Each subcarrier index is an unsigned number in the range 1 to
NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 32, all remaining
octets are set to the value 0. Note that the content of this
object should be correlated with the sub-carriers mask and with
the RFI setup."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
::= { adsl2LineConfProfModeSpecEntry 7 }
DESCRIPTION
"The downstream PSD mask applicable at the U-C2 reference
point.
This parameter is used only for G.992.5, and it may impose PSD
restrictions (breakpoints) in addition to the Limit PSD mask
defined in G.992.5.
This is a string of 32 pairs of values in the following
structure:
Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 94-95, which are
associated with a 32nd breakpoint.
Each subcarrier index is an unsigned number in the range 1 to
NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 32, all remaining
octets are set to the value 0. Note that the content of this
object should be correlated with the sub-carriers mask and with
the RFI setup."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
::= { adsl2LineConfProfModeSpecEntry 7 }
adsl2LConfProfPsdMaskUs OBJECT-TYPE SYNTAX Adsl2PsdMaskUs MAX-ACCESS read-create STATUS current DESCRIPTION "The upstream PSD mask applicable at the U-R2 reference point. This parameter is used only for G.992.5, and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 4 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 9-11, which are associated with a 4th breakpoint. Each subcarrier index is an unsigned number in the range 1 to
adsl2LConfProfPsdMaskUs对象类型语法Adsl2PsdMaskUs MAX-ACCESS read create STATUS current DESCRIPTION“适用于U-R2参考点的上游PSD掩码。此参数仅用于G.992.5，可能会施加PSD限制（断点）除了G.992.5中定义的限制PSD掩码外，这是一个由以下结构中的4对值组成的字符串：八位字节0+1-第一个断点上下文中使用的第一个子载波的索引。八位字节2-八位字节0和1中指示的子载波的PSD缩减。八位字节3-5-相同，用于第二个断点。八位字节6-8-相同，用于第三个断点断点。此体系结构持续到与第四个断点关联的八位字节9-11。每个子载波索引都是1到10之间的无符号数
NSCus. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 4, all remaining
octets are set to the value 0. Note that the content of this
object should be correlated with the sub-carriers mask and with
the RFI setup."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
::= { adsl2LineConfProfModeSpecEntry 8 }
NSCus. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 4, all remaining
octets are set to the value 0. Note that the content of this
object should be correlated with the sub-carriers mask and with
the RFI setup."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
::= { adsl2LineConfProfModeSpecEntry 8 }
adsl2LConfProfPsdMaskSelectUs OBJECT-TYPE
SYNTAX Unsigned32(1..9)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The selected upstream PSD mask. This parameter is used only
for annexes J and M of G.992.3 and G.992.5, and the same
selection is used for all relevant enabled bits in
adsl2LConfProfAtuTransSysEna."
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.2.10"
DEFVAL { 1 }
::= { adsl2LineConfProfModeSpecEntry 9 }
adsl2LConfProfPsdMaskSelectUs OBJECT-TYPE
SYNTAX Unsigned32(1..9)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The selected upstream PSD mask. This parameter is used only
for annexes J and M of G.992.3 and G.992.5, and the same
selection is used for all relevant enabled bits in
adsl2LConfProfAtuTransSysEna."
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.2.10"
DEFVAL { 1 }
::= { adsl2LineConfProfModeSpecEntry 9 }
adsl2LConfProfModeSpecRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION
adsl2LConfProfModeSpecRowStatus对象类型语法RowStatus MAX-ACCESS读取创建状态当前说明
"This object is used to create a new row or to modify or delete an existing row in this table.
“此对象用于创建新行或修改或删除此表中的现有行。
A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile.
通过将此对象设置为“活动”来激活配置文件。设置“激活”时，系统将验证配置文件。
Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must first be unreferenced from all associated templates."
在删除配置文件或使其退出服务（通过将此对象设置为“销毁”或“notInService”）之前，必须先从所有关联模板中取消引用该配置文件。”
::= { adsl2LineConfProfModeSpecEntry 10 }
::= { adsl2LineConfProfModeSpecEntry 10 }
------------------------------------------------
-- adsl2ChConfProfileTable --
------------------------------------------------
adsl2ChConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2ChConfProfileEntry
MAX-ACCESS not-accessible
------------------------------------------------
-- adsl2ChConfProfileTable --
------------------------------------------------
adsl2ChConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2ChConfProfileEntry
MAX-ACCESS not-accessible
STATUS current DESCRIPTION "The table adsl2ChConfProfileTable contains ADSL2 channel profile configuration.
状态当前说明“表adsl2ChConfProfileTable包含ADSL2信道配置文件配置。
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileChannel 1 }
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileChannel 1 }
adsl2ChConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2ChConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChConfProfileTable contains ADSL2 channel
profile configuration.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this document."
INDEX { adsl2ChConfProfProfileName }
::= { adsl2ChConfProfileTable 1 }
adsl2ChConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2ChConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChConfProfileTable contains ADSL2 channel
profile configuration.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this document."
INDEX { adsl2ChConfProfProfileName }
::= { adsl2ChConfProfileTable 1 }
Adsl2ChConfProfileEntry ::=
SEQUENCE {
adsl2ChConfProfProfileName SnmpAdminString,
adsl2ChConfProfMinDataRateDs Unsigned32,
adsl2ChConfProfMinDataRateUs Unsigned32,
adsl2ChConfProfMinResDataRateDs Unsigned32,
adsl2ChConfProfMinResDataRateUs Unsigned32,
adsl2ChConfProfMaxDataRateDs Unsigned32,
adsl2ChConfProfMaxDataRateUs Unsigned32,
adsl2ChConfProfMinDataRateLowPwrDs Unsigned32,
adsl2ChConfProfMaxDelayDs Unsigned32,
adsl2ChConfProfMaxDelayUs Unsigned32,
adsl2ChConfProfMinProtectionDs Adsl2SymbolProtection,
adsl2ChConfProfMinProtectionUs Adsl2SymbolProtection,
adsl2ChConfProfMaxBerDs Adsl2MaxBer,
adsl2ChConfProfMaxBerUs Adsl2MaxBer,
adsl2ChConfProfUsDataRateDs Unsigned32,
adsl2ChConfProfDsDataRateDs Unsigned32,
adsl2ChConfProfUsDataRateUs Unsigned32,
adsl2ChConfProfDsDataRateUs Unsigned32,
adsl2ChConfProfImaEnabled TruthValue,
adsl2ChConfProfRowStatus RowStatus
}
Adsl2ChConfProfileEntry ::=
SEQUENCE {
adsl2ChConfProfProfileName SnmpAdminString,
adsl2ChConfProfMinDataRateDs Unsigned32,
adsl2ChConfProfMinDataRateUs Unsigned32,
adsl2ChConfProfMinResDataRateDs Unsigned32,
adsl2ChConfProfMinResDataRateUs Unsigned32,
adsl2ChConfProfMaxDataRateDs Unsigned32,
adsl2ChConfProfMaxDataRateUs Unsigned32,
adsl2ChConfProfMinDataRateLowPwrDs Unsigned32,
adsl2ChConfProfMaxDelayDs Unsigned32,
adsl2ChConfProfMaxDelayUs Unsigned32,
adsl2ChConfProfMinProtectionDs Adsl2SymbolProtection,
adsl2ChConfProfMinProtectionUs Adsl2SymbolProtection,
adsl2ChConfProfMaxBerDs Adsl2MaxBer,
adsl2ChConfProfMaxBerUs Adsl2MaxBer,
adsl2ChConfProfUsDataRateDs Unsigned32,
adsl2ChConfProfDsDataRateDs Unsigned32,
adsl2ChConfProfUsDataRateUs Unsigned32,
adsl2ChConfProfDsDataRateUs Unsigned32,
adsl2ChConfProfImaEnabled TruthValue,
adsl2ChConfProfRowStatus RowStatus
}
adsl2ChConfProfProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32))
adsl2ChConfProfProfileName对象类型语法snmpadmin字符串（大小（1..32））
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2ChConfProfileEntry 1 }
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2ChConfProfileEntry 1 }
adsl2ChConfProfMinDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Data Rate on Downstream direction. The minimum net
data rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 2 }
adsl2ChConfProfMinDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Data Rate on Downstream direction. The minimum net
data rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 2 }
adsl2ChConfProfMinDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Data Rate on Upstream direction. The minimum net data
rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 3 }
adsl2ChConfProfMinDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Data Rate on Upstream direction. The minimum net data
rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 3 }
adsl2ChConfProfMinResDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Reserved Data Rate on Downstream direction. The
minimum reserved net data rate for the bearer channel, coded
in bits/second. This parameter is used only if the Rate
Adaptation Mode in the direction of the bearer channel (i.e.,
adsl2LConfProfRaModeDs) is set to dynamicRa."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 4 }
adsl2ChConfProfMinResDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Reserved Data Rate on Downstream direction. The
minimum reserved net data rate for the bearer channel, coded
in bits/second. This parameter is used only if the Rate
Adaptation Mode in the direction of the bearer channel (i.e.,
adsl2LConfProfRaModeDs) is set to dynamicRa."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 4 }
adsl2ChConfProfMinResDataRateUs OBJECT-TYPE SYNTAX Unsigned32(0..200000000) UNITS "bits/second" MAX-ACCESS read-create STATUS current DESCRIPTION
adsl2ChConfProfMinResDataRateUs对象类型语法无符号32（0..20000000）单位“位/秒”最大访问读取创建状态当前说明
"Minimum Reserved Data Rate on Upstream direction. The minimum
reserved net data rate for the bearer channel, coded in
bits/second. This parameter is used only if the Rate
Adaptation Mode in the direction of the bearer channel (i.e.,
adsl2LConfProfRaModeUs) is set to dynamicRa."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 5 }
"Minimum Reserved Data Rate on Upstream direction. The minimum
reserved net data rate for the bearer channel, coded in
bits/second. This parameter is used only if the Rate
Adaptation Mode in the direction of the bearer channel (i.e.,
adsl2LConfProfRaModeUs) is set to dynamicRa."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 5 }
adsl2ChConfProfMaxDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Data Rate on Downstream direction. The maximum net
data rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 6 }
adsl2ChConfProfMaxDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Data Rate on Downstream direction. The maximum net
data rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 6 }
adsl2ChConfProfMaxDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Data Rate on Upstream direction. The maximum net data
rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 7 }
adsl2ChConfProfMaxDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Data Rate on Upstream direction. The maximum net data
rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 7 }
adsl2ChConfProfMinDataRateLowPwrDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Data Rate in Low Power state on Downstream direction.
The minimum net data rate for the bearer channel, coded in
bits/second, during the low power state (L1 in G.992.2, L2 in
G.992.3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 8 }
adsl2ChConfProfMinDataRateLowPwrDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Data Rate in Low Power state on Downstream direction.
The minimum net data rate for the bearer channel, coded in
bits/second, during the low power state (L1 in G.992.2, L2 in
G.992.3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 8 }
adsl2ChConfProfMaxDelayDs OBJECT-TYPE SYNTAX Unsigned32(0..63) UNITS "milliseconds" MAX-ACCESS read-create STATUS current
adsl2ChConfProfMaxDelayDs对象类型语法无符号32（0..63）单位“毫秒”最大读取创建状态当前
DESCRIPTION
"Maximum Interleave Delay on Downstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on
Downstream direction. The ATUs shall choose the S (factor)
and D (depth) values such that the actual one-way interleaving
delay (adsl2ChStatusActDelay) is as close as possible to,
but less than or equal to, adsl2ChConfProfMaxDelayDs. The
delay is coded in ms, with the value 0 indicating no delay
bound is being imposed."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.2"
::= { adsl2ChConfProfileEntry 9 }
DESCRIPTION
"Maximum Interleave Delay on Downstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on
Downstream direction. The ATUs shall choose the S (factor)
and D (depth) values such that the actual one-way interleaving
delay (adsl2ChStatusActDelay) is as close as possible to,
but less than or equal to, adsl2ChConfProfMaxDelayDs. The
delay is coded in ms, with the value 0 indicating no delay
bound is being imposed."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.2"
::= { adsl2ChConfProfileEntry 9 }
adsl2ChConfProfMaxDelayUs OBJECT-TYPE
SYNTAX Unsigned32(0..63)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Interleave Delay on Upstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on
Upstream direction. The ATUs shall choose the S (factor) and
D (depth) values such that the actual one-way interleaving
delay (adsl2ChStatusActDelay) is as close as possible to,
but less than or equal to, adsl2ChConfProfMaxDelayUs. The
delay is coded in ms, with the value 0 indicating no delay
bound is being imposed."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.2"
::= { adsl2ChConfProfileEntry 10 }
adsl2ChConfProfMaxDelayUs OBJECT-TYPE
SYNTAX Unsigned32(0..63)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Interleave Delay on Upstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on
Upstream direction. The ATUs shall choose the S (factor) and
D (depth) values such that the actual one-way interleaving
delay (adsl2ChStatusActDelay) is as close as possible to,
but less than or equal to, adsl2ChConfProfMaxDelayUs. The
delay is coded in ms, with the value 0 indicating no delay
bound is being imposed."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.2"
::= { adsl2ChConfProfileEntry 10 }
adsl2ChConfProfMinProtectionDs OBJECT-TYPE
SYNTAX Adsl2SymbolProtection
UNITS "symbols"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Impulse Noise Protection on Downstream direction. The
minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following
values: noProtection (i.e., INP not required), halfSymbol
(i.e., INP length is 1/2 symbol), and 1-16 symbols in steps
of 1 symbol."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.3"
DEFVAL { noProtection }
::= { adsl2ChConfProfileEntry 11 }
adsl2ChConfProfMinProtectionDs OBJECT-TYPE
SYNTAX Adsl2SymbolProtection
UNITS "symbols"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Impulse Noise Protection on Downstream direction. The
minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following
values: noProtection (i.e., INP not required), halfSymbol
(i.e., INP length is 1/2 symbol), and 1-16 symbols in steps
of 1 symbol."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.3"
DEFVAL { noProtection }
::= { adsl2ChConfProfileEntry 11 }
adsl2ChConfProfMinProtectionUs OBJECT-TYPE SYNTAX Adsl2SymbolProtection UNITS "symbols"
adsl2ChConfProfMinProtectionUs对象类型语法ADSL2SYMBOL保护单元“符号”
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Impulse Noise Protection on Upstream direction. The
minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following
values: noProtection (i.e., INP not required), halfSymbol
(i.e., INP length is 1/2 symbol), and 1-16 symbols in steps
of 1 symbol."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.3"
DEFVAL { noProtection }
::= { adsl2ChConfProfileEntry 12 }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Impulse Noise Protection on Upstream direction. The
minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following
values: noProtection (i.e., INP not required), halfSymbol
(i.e., INP length is 1/2 symbol), and 1-16 symbols in steps
of 1 symbol."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.3"
DEFVAL { noProtection }
::= { adsl2ChConfProfileEntry 12 }
adsl2ChConfProfMaxBerDs OBJECT-TYPE
SYNTAX Adsl2MaxBer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Bit Error Ratio on Downstream direction. The maximum
bit error ratio for the bearer channel. The parameter can
take the following values (for 1E-3, 1E-5 or 1E-7):
eminus3(1),
eminus5(2), or
eminus7(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.4"
DEFVAL { eminus5 }
::= { adsl2ChConfProfileEntry 13 }
adsl2ChConfProfMaxBerDs OBJECT-TYPE
SYNTAX Adsl2MaxBer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Bit Error Ratio on Downstream direction. The maximum
bit error ratio for the bearer channel. The parameter can
take the following values (for 1E-3, 1E-5 or 1E-7):
eminus3(1),
eminus5(2), or
eminus7(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.4"
DEFVAL { eminus5 }
::= { adsl2ChConfProfileEntry 13 }
adsl2ChConfProfMaxBerUs OBJECT-TYPE
SYNTAX Adsl2MaxBer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Bit Error Ratio on Upstream direction. The maximum
bit error ratio for the bearer channel. The parameter can
take the following values (for 1E-3, 1E-5 or 1E-7):
eminus3(1),
eminus5(2), or
eminus7(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.4"
DEFVAL { eminus5 }
::= { adsl2ChConfProfileEntry 14 }
adsl2ChConfProfMaxBerUs OBJECT-TYPE
SYNTAX Adsl2MaxBer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Bit Error Ratio on Upstream direction. The maximum
bit error ratio for the bearer channel. The parameter can
take the following values (for 1E-3, 1E-5 or 1E-7):
eminus3(1),
eminus5(2), or
eminus7(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.4"
DEFVAL { eminus5 }
::= { adsl2ChConfProfileEntry 14 }
adsl2ChConfProfUsDataRateDs OBJECT-TYPE SYNTAX Unsigned32(0..200000000) UNITS "bits/second" MAX-ACCESS read-create STATUS current
adsl2ChConfProfUsDataRateDs对象类型语法无符号32（0..20000000）单位“位/秒”最大读取创建状态当前
DESCRIPTION
"Data Rate Threshold Up shift for downstream direction. An
'Up-shift rate change' event is triggered when the actual
downstream data rate exceeds, by more than the threshold, the
data rate at the last entry into Showtime. The parameter is
coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 15 }
DESCRIPTION
"Data Rate Threshold Up shift for downstream direction. An
'Up-shift rate change' event is triggered when the actual
downstream data rate exceeds, by more than the threshold, the
data rate at the last entry into Showtime. The parameter is
coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 15 }
adsl2ChConfProfDsDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Data Rate Threshold Down-shift for downstream direction. A
'Down-shift rate change' event is triggered when the actual
downstream data rate is below the data rate at the last entry
into Showtime, by more than the threshold. The parameter is
coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 16 }
adsl2ChConfProfDsDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Data Rate Threshold Down-shift for downstream direction. A
'Down-shift rate change' event is triggered when the actual
downstream data rate is below the data rate at the last entry
into Showtime, by more than the threshold. The parameter is
coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 16 }
adsl2ChConfProfUsDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Data Rate Threshold Up shift for upstream direction. An
'Up-shift rate change' event is triggered when the actual
upstream data rate exceeds, by more than the threshold, the
data rate at the last entry into Showtime. The parameter is
coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 17 }
adsl2ChConfProfUsDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000)
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Data Rate Threshold Up shift for upstream direction. An
'Up-shift rate change' event is triggered when the actual
upstream data rate exceeds, by more than the threshold, the
data rate at the last entry into Showtime. The parameter is
coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 17 }
adsl2ChConfProfDsDataRateUs OBJECT-TYPE SYNTAX Unsigned32(0..200000000) UNITS "bits/second" MAX-ACCESS read-create STATUS current DESCRIPTION "Data Rate Threshold Down-shift for upstream direction. A 'Down-shift rate change' event is triggered when the actual upstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bits/second."
adsl2ChConfProfDsDataRateUs对象类型语法无符号32（0..20000000）单位“位/秒”最大访问读取创建状态当前说明“上行方向的数据速率阈值下移。当实际上游数据速率低于Showtime最后一次输入时的数据速率超过阈值时，会触发“下移速率更改”事件。参数的编码单位为位/秒。”
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 18 }
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 18 }
adsl2ChConfProfImaEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"IMA Mode Enable. The parameter enables the IMA operation mode
in the ATM Data Path. Relevant only if the channel is an ATM
Data Path. When in 'enable' state, the ATM data path should
comply with the requirements for IMA transmission."
REFERENCE "ITU-T G.997.1, paragraph 7.3.4.1"
DEFVAL { false }
::= { adsl2ChConfProfileEntry 19 }
adsl2ChConfProfImaEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"IMA Mode Enable. The parameter enables the IMA operation mode
in the ATM Data Path. Relevant only if the channel is an ATM
Data Path. When in 'enable' state, the ATM data path should
comply with the requirements for IMA transmission."
REFERENCE "ITU-T G.997.1, paragraph 7.3.4.1"
DEFVAL { false }
::= { adsl2ChConfProfileEntry 19 }
adsl2ChConfProfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table.
adsl2ChConfProfRowStatus对象类型语法RowStatus MAX-ACCESS read create STATUS current DESCRIPTION“此对象用于创建新行或修改或删除此表中的现有行。
A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile.
通过将此对象设置为“活动”来激活配置文件。设置“激活”时，系统将验证配置文件。
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2ChConfProfileEntry 20 }
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2ChConfProfileEntry 20 }
------------------------------------------------
-- adsl2LineAlarmConfTemplateTable --
------------------------------------------------
adsl2LineAlarmConfTemplateTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineAlarmConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineAlarmConfTemplateTable contains
ADSL2 line configuration templates.
------------------------------------------------
-- adsl2LineAlarmConfTemplateTable --
------------------------------------------------
adsl2LineAlarmConfTemplateTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineAlarmConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineAlarmConfTemplateTable contains
ADSL2 line configuration templates.
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileAlarmConf 1 }
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileAlarmConf 1 }
adsl2LineAlarmConfTemplateEntry OBJECT-TYPE
SYNTAX Adsl2LineAlarmConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineAlarmConfTemplateTable contains ADSL2
line PM thresholds templates.
A default template with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this
document."
INDEX { adsl2LAlarmConfTempTemplateName }
::= { adsl2LineAlarmConfTemplateTable 1 }
adsl2LineAlarmConfTemplateEntry OBJECT-TYPE
SYNTAX Adsl2LineAlarmConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineAlarmConfTemplateTable contains ADSL2
line PM thresholds templates.
A default template with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this
document."
INDEX { adsl2LAlarmConfTempTemplateName }
::= { adsl2LineAlarmConfTemplateTable 1 }
Adsl2LineAlarmConfTemplateEntry ::=
SEQUENCE {
adsl2LAlarmConfTempTemplateName SnmpAdminString,
adsl2LAlarmConfTempLineProfile SnmpAdminString,
adsl2LAlarmConfTempChan1ConfProfile SnmpAdminString,
adsl2LAlarmConfTempChan2ConfProfile SnmpAdminString,
adsl2LAlarmConfTempChan3ConfProfile SnmpAdminString,
adsl2LAlarmConfTempChan4ConfProfile SnmpAdminString,
adsl2LAlarmConfTempRowStatus RowStatus
}
Adsl2LineAlarmConfTemplateEntry ::=
SEQUENCE {
adsl2LAlarmConfTempTemplateName SnmpAdminString,
adsl2LAlarmConfTempLineProfile SnmpAdminString,
adsl2LAlarmConfTempChan1ConfProfile SnmpAdminString,
adsl2LAlarmConfTempChan2ConfProfile SnmpAdminString,
adsl2LAlarmConfTempChan3ConfProfile SnmpAdminString,
adsl2LAlarmConfTempChan4ConfProfile SnmpAdminString,
adsl2LAlarmConfTempRowStatus RowStatus
}
adsl2LAlarmConfTempTemplateName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2LineAlarmConfTemplateEntry 1 }
adsl2LAlarmConfTempTemplateName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2LineAlarmConfTemplateEntry 1 }
adsl2LAlarmConfTempLineProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2 Line
Thresholds Configuration Profile Table
(adsl2LineAlarmConfProfileTable) that applies to this ADSL2
line."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "DEFVAL" }
::= { adsl2LineAlarmConfTemplateEntry 2 }
adsl2LAlarmConfTempLineProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2 Line
Thresholds Configuration Profile Table
(adsl2LineAlarmConfProfileTable) that applies to this ADSL2
line."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "DEFVAL" }
::= { adsl2LineAlarmConfTemplateEntry 2 }
adsl2LAlarmConfTempChan1ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32))
ADSL2AlarmConfTempChan1ConfProfile对象类型语法SnmpAdminString（大小（1..32））
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #1. The channel profile name specified here
must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "DEFVAL" }
::= { adsl2LineAlarmConfTemplateEntry 3 }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #1. The channel profile name specified here
must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "DEFVAL" }
::= { adsl2LineAlarmConfTemplateEntry 3 }
adsl2LAlarmConfTempChan2ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #2. The channel profile name specified here
must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table. If the channel is unused,
then the object is set to a zero-length string."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "" }
::= { adsl2LineAlarmConfTemplateEntry 4 }
adsl2LAlarmConfTempChan2ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #2. The channel profile name specified here
must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table. If the channel is unused,
then the object is set to a zero-length string."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "" }
::= { adsl2LineAlarmConfTemplateEntry 4 }
adsl2LAlarmConfTempChan3ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #3. The channel profile name specified here
must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table.
This object may be set to a non-zero-length string only if
adsl2LAlarmConfTempChan2ConfProfile contains a non-zero-
length string."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "" }
::= { adsl2LineAlarmConfTemplateEntry 5 }
adsl2LAlarmConfTempChan3ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #3. The channel profile name specified here
must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table.
This object may be set to a non-zero-length string only if
adsl2LAlarmConfTempChan2ConfProfile contains a non-zero-
length string."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "" }
::= { adsl2LineAlarmConfTemplateEntry 5 }
adsl2LAlarmConfTempChan4ConfProfile OBJECT-TYPE
ADSL2AlarmConfTempChan4ConfProfile对象类型
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #4. The channel profile name specified here
must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table.
This object may be set to a non-zero-length string only if
adsl2LAlarmConfTempChan3ConfProfile contains a non-zero-
length string."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "" }
::= { adsl2LineAlarmConfTemplateEntry 6 }
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #4. The channel profile name specified here
must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table.
This object may be set to a non-zero-length string only if
adsl2LAlarmConfTempChan3ConfProfile contains a non-zero-
length string."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "" }
::= { adsl2LineAlarmConfTemplateEntry 6 }
adsl2LAlarmConfTempRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table.
ADSL2LARMCONFTEMPROWSTATUS对象类型语法RowStatus MAX-ACCESS read create STATUS current DESCRIPTION“此对象用于创建新行或修改或删除此表中的现有行。
A template is activated by setting this object to 'active'. When 'active' is set, the system will validate the template.
通过将此对象设置为“活动”来激活模板。设置“活动”时，系统将验证模板。
Before a template can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
lines."
::= { adsl2LineAlarmConfTemplateEntry 7 }
Before a template can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
lines."
::= { adsl2LineAlarmConfTemplateEntry 7 }
------------------------------------------------
-- adsl2LineAlarmConfProfileTable --
------------------------------------------------
------------------------------------------------
-- adsl2LineAlarmConfProfileTable --
------------------------------------------------
adsl2LineAlarmConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF Adsl2LineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles.
adsl2LineAlarmConfProfileTable对象类型语法Adsl2LineAlarmConfProfileEntry MAX-ACCESS不可访问状态当前描述“表adsl2LineAlarmConfProfileTable包含ADSL2线路PM阈值配置文件。
Entries in this table MUST be maintained in a persistent manner."
必须以持久方式维护此表中的条目。”
::= { adsl2ProfileAlarmConf 2 }
::= { adsl2ProfileAlarmConf 2 }
adsl2LineAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2LineAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineAlarmConfProfileTable contains ADSL2
line PM thresholds profiles.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this
document."
INDEX { adsl2LineAlarmConfProfileName }
::= { adsl2LineAlarmConfProfileTable 1 }
adsl2LineAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2LineAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineAlarmConfProfileTable contains ADSL2
line PM thresholds profiles.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this
document."
INDEX { adsl2LineAlarmConfProfileName }
::= { adsl2LineAlarmConfProfileTable 1 }
Adsl2LineAlarmConfProfileEntry ::=
SEQUENCE {
adsl2LineAlarmConfProfileName SnmpAdminString,
adsl2LineAlarmConfProfileAtucThresh15MinFecs
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinEs
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinSes
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinLoss
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinUas
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinFecs
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinEs
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinSes
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinLoss
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinUas
HCPerfIntervalThreshold,
Adsl2LineAlarmConfProfileEntry ::=
SEQUENCE {
adsl2LineAlarmConfProfileName SnmpAdminString,
adsl2LineAlarmConfProfileAtucThresh15MinFecs
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinEs
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinSes
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinLoss
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinUas
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinFecs
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinEs
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinSes
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinLoss
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinUas
HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileThresh15MinFailedFullInt Unsigned32, adsl2LineAlarmConfProfileThresh15MinFailedShrtInt Unsigned32,
adsl2LineAlarmConfProfileThresh15MinFailedFullInt Unsigned32，adsl2LineAlarmConfProfileThresh15MinFailedShrtInt Unsigned32，
adsl2LineAlarmConfProfileRowStatus RowStatus }
ADSL2LINEARMCONFPROFILEROWSTATUS RowStatus}
adsl2LineAlarmConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32))
adsl2LineAlarmConfProfileName对象类型语法SnmpAdminString（大小（1..32））
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2LineAlarmConfProfileEntry 1 }
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2LineAlarmConfProfileEntry 1 }
adsl2LineAlarmConfProfileAtucThresh15MinFecs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MFecs counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 2 }
adsl2LineAlarmConfProfileAtucThresh15MinFecs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MFecs counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 2 }
adsl2LineAlarmConfProfileAtucThresh15MinEs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MEs counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 3 }
adsl2LineAlarmConfProfileAtucThresh15MinEs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MEs counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 3 }
adsl2LineAlarmConfProfileAtucThresh15MinSes OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MSes counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 4 }
adsl2LineAlarmConfProfileAtucThresh15MinSes OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MSes counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 4 }
adsl2LineAlarmConfProfileAtucThresh15MinLoss OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MLoss counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 5 }
adsl2LineAlarmConfProfileAtucThresh15MinLoss OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MLoss counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 5 }
adsl2LineAlarmConfProfileAtucThresh15MinUas OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MUas counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 6 }
adsl2LineAlarmConfProfileAtucThresh15MinUas OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MUas counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 6 }
adsl2LineAlarmConfProfileAturThresh15MinFecs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MFecs counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 7 }
adsl2LineAlarmConfProfileAturThresh15MinFecs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MFecs counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 7 }
adsl2LineAlarmConfProfileAturThresh15MinEs OBJECT-TYPE SYNTAX HCPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION
ADSL2LINEARMCONFPROFILEATURTHRESHTML5MINES对象类型语法HCPerfIntervalThreshold单位“秒”最大访问读取创建状态当前描述
"A threshold for the adsl2PMLCurr15MEs counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 8 }
"A threshold for the adsl2PMLCurr15MEs counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 8 }
adsl2LineAlarmConfProfileAturThresh15MinSes OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MSes counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 9 }
adsl2LineAlarmConfProfileAturThresh15MinSes OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MSes counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 9 }
adsl2LineAlarmConfProfileAturThresh15MinLoss OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MLoss counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 10 }
adsl2LineAlarmConfProfileAturThresh15MinLoss OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MLoss counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 10 }
adsl2LineAlarmConfProfileAturThresh15MinUas OBJECT-TYPE SYNTAX HCPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "A threshold for the adsl2PMLCurr15MUas counter, when adsl2PMLCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph 7.3.1" DEFVAL { 0 }
ADSL2LineAlarmConfProfileATURTHRESH15minas对象类型语法HCPerfIntervalThreshold UNITS“秒”MAX-ACCESS read create STATUS current DESCRIPTION“当ADSL2PMLCURRUNT为atur（2）时，adsl2PMLCurr15MUas计数器的阈值。值0表示未为相关计数器指定阈值。”参考“ITU-T G.997.1，第7.3.1段”定义{0}
::= { adsl2LineAlarmConfProfileEntry 11 }
::= { adsl2LineAlarmConfProfileEntry 11 }
adsl2LineAlarmConfProfileThresh15MinFailedFullInt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurrInit15MfailedFullInits
counter.
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 12 }
adsl2LineAlarmConfProfileThresh15MinFailedFullInt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurrInit15MfailedFullInits
counter.
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 12 }
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurrInit15MFailedShortInits
counter.
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 13 }
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurrInit15MFailedShortInits
counter.
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 13 }
adsl2LineAlarmConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table.
ADSL2LINEARMCONFPROFILEROWSTATUS对象类型语法RowStatus MAX-ACCESS read create STATUS current DESCRIPTION“此对象用于创建新行或修改或删除此表中的现有行。
A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile.
通过将此对象设置为“活动”来激活配置文件。设置“激活”时，系统将验证配置文件。
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2LineAlarmConfProfileEntry 14 }
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2LineAlarmConfProfileEntry 14 }
------------------------------------------------
-- adsl2ChAlarmConfProfileTable --
------------------------------------------------
-- adsl2ChAlarmConfProfileTable --
------------------------------------------------
------------------------------------------------
adsl2ChAlarmConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF Adsl2ChAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles.
adsl2ChAlarmConfProfileTable Adsl2ChAlarmConfProfileEntry的对象类型语法序列MAX-ACCESS不可访问状态当前描述“表adsl2ChAlarmConfProfileTable包含ADSL2通道PM阈值配置文件。
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileAlarmConf 3 }
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileAlarmConf 3 }
adsl2ChAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2ChAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChAlarmConfProfileTable contains ADSL2
channel PM thresholds profiles.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this document."
INDEX { adsl2ChAlarmConfProfileName }
::= { adsl2ChAlarmConfProfileTable 1 }
adsl2ChAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2ChAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChAlarmConfProfileTable contains ADSL2
channel PM thresholds profiles.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this document."
INDEX { adsl2ChAlarmConfProfileName }
::= { adsl2ChAlarmConfProfileTable 1 }
Adsl2ChAlarmConfProfileEntry ::=
SEQUENCE {
adsl2ChAlarmConfProfileName
SnmpAdminString,
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations
Unsigned32,
adsl2ChAlarmConfProfileAtucThresh15MinCorrected Unsigned32,
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations
Unsigned32,
adsl2ChAlarmConfProfileAturThresh15MinCorrected Unsigned32,
adsl2ChAlarmConfProfileRowStatus RowStatus
}
Adsl2ChAlarmConfProfileEntry ::=
SEQUENCE {
adsl2ChAlarmConfProfileName
SnmpAdminString,
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations
Unsigned32,
adsl2ChAlarmConfProfileAtucThresh15MinCorrected Unsigned32,
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations
Unsigned32,
adsl2ChAlarmConfProfileAturThresh15MinCorrected Unsigned32,
adsl2ChAlarmConfProfileRowStatus RowStatus
}
adsl2ChAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2ChAlarmConfProfileEntry 1 }
adsl2ChAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2ChAlarmConfProfileEntry 1 }
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMChCurr15MCodingViolations
counter, when adsl2PMChCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 2 }
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMChCurr15MCodingViolations
counter, when adsl2PMChCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 2 }
adsl2ChAlarmConfProfileAtucThresh15MinCorrected OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMChCurr15MCorrectedBlocks
counter, when adsl2PMChCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 3 }
adsl2ChAlarmConfProfileAtucThresh15MinCorrected OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMChCurr15MCorrectedBlocks
counter, when adsl2PMChCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 3 }
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMChCurr15MCodingViolations
counter, when adsl2PMChCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 4 }
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMChCurr15MCodingViolations
counter, when adsl2PMChCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 4 }
adsl2ChAlarmConfProfileAturThresh15MinCorrected OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "A threshold for the adsl2PMChCurr15MCorrectedBlocks counter, when adsl2PMChCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter."
ADSL2CHALARMConfProfileATURSTHERTHS15MINCORRECTED对象类型语法Unsigned32 MAX-ACCESS read create STATUS当前描述“当adsl2PMChCurrUnit为atur（2）时，ADSL2PMCHCURR15MCORRECTED BLOCKS计数器的阈值。值0表示未为关联计数器指定阈值。”
REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 5 }
REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 5 }
adsl2ChAlarmConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table.
adsl2ChAlarmConfProfileRowStatus对象类型语法RowStatus MAX-ACCESS read create STATUS current DESCRIPTION“此对象用于创建新行或修改或删除此表中的现有行。
A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile.
通过将此对象设置为“活动”来激活配置文件。设置“激活”时，系统将验证配置文件。
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2ChAlarmConfProfileEntry 6 }
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2ChAlarmConfProfileEntry 6 }
------------------------------------------------
-- PM line current counters --
------------------------------------------------
adsl2PMLineCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 lines."
::= { adsl2PMLine 1 }
------------------------------------------------
-- PM line current counters --
------------------------------------------------
adsl2PMLineCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 lines."
::= { adsl2PMLine 1 }
adsl2PMLineCurrEntry OBJECT-TYPE
SYNTAX Adsl2PMLineCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 lines.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), along with a
termination unit.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
INDEX { ifIndex, adsl2PMLCurrUnit }
::= { adsl2PMLineCurrTable 1 }
adsl2PMLineCurrEntry OBJECT-TYPE
SYNTAX Adsl2PMLineCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 lines.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), along with a
termination unit.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
INDEX { ifIndex, adsl2PMLCurrUnit }
::= { adsl2PMLineCurrTable 1 }
Adsl2PMLineCurrEntry ::=
SEQUENCE {
adsl2PMLCurrUnit Adsl2Unit,
adsl2PMLCurrValidIntervals Unsigned32,
adsl2PMLCurrInvalidIntervals Unsigned32,
adsl2PMLCurr15MTimeElapsed HCPerfTimeElapsed,
adsl2PMLCurr15MFecs Counter32,
adsl2PMLCurr15MEs Counter32,
adsl2PMLCurr15MSes Counter32,
adsl2PMLCurr15MLoss Counter32,
adsl2PMLCurr15MUas Counter32,
adsl2PMLCurr1DayValidIntervals Unsigned32,
adsl2PMLCurr1DayInvalidIntervals Unsigned32,
adsl2PMLCurr1DayTimeElapsed HCPerfTimeElapsed,
adsl2PMLCurr1DayFecs Counter32,
adsl2PMLCurr1DayEs Counter32,
adsl2PMLCurr1DaySes Counter32,
adsl2PMLCurr1DayLoss Counter32,
adsl2PMLCurr1DayUas Counter32
}
Adsl2PMLineCurrEntry ::=
SEQUENCE {
adsl2PMLCurrUnit Adsl2Unit,
adsl2PMLCurrValidIntervals Unsigned32,
adsl2PMLCurrInvalidIntervals Unsigned32,
adsl2PMLCurr15MTimeElapsed HCPerfTimeElapsed,
adsl2PMLCurr15MFecs Counter32,
adsl2PMLCurr15MEs Counter32,
adsl2PMLCurr15MSes Counter32,
adsl2PMLCurr15MLoss Counter32,
adsl2PMLCurr15MUas Counter32,
adsl2PMLCurr1DayValidIntervals Unsigned32,
adsl2PMLCurr1DayInvalidIntervals Unsigned32,
adsl2PMLCurr1DayTimeElapsed HCPerfTimeElapsed,
adsl2PMLCurr1DayFecs Counter32,
adsl2PMLCurr1DayEs Counter32,
adsl2PMLCurr1DaySes Counter32,
adsl2PMLCurr1DayLoss Counter32,
adsl2PMLCurr1DayUas Counter32
}
adsl2PMLCurrUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit atuc(1) or atur(2)."
::= { adsl2PMLineCurrEntry 1 }
adsl2PMLCurrUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit atuc(1) or atur(2)."
::= { adsl2PMLineCurrEntry 1 }
adsl2PMLCurrValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMLineCurrEntry 2 }
adsl2PMLCurrValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMLineCurrEntry 2 }
adsl2PMLCurrInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMLineCurrEntry 3 }
adsl2PMLCurrInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMLineCurrEntry 3 }
adsl2PMLCurr15MTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds"
adsl2pmlcurr15mtimeessed对象类型语法hcperftimeessed单位“秒”
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLineCurrEntry 4 }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLineCurrEntry 4 }
adsl2PMLCurr15MFecs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 5 }
adsl2PMLCurr15MFecs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 5 }
adsl2PMLCurr15MEs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >=1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >=1 OR RDI >=1 OR LPR-FE >=1 .
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 6 }
adsl2PMLCurr15MEs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >=1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >=1 OR RDI >=1 OR LPR-FE >=1 .
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 6 }
adsl2PMLCurr15MSes OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 .
This parameter is inhibited during UAS."
adsl2PMLCurr15MSes OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 .
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 7 }
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 7 }
adsl2PMLCurr15MLoss OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was LOS (or
LOS-FE for ATU-R)."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 8 }
adsl2PMLCurr15MLoss OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was LOS (or
LOS-FE for ATU-R)."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 8 }
adsl2PMLCurr15MUas OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this
interval. Unavailability begins at the onset of 10
contiguous severely-errored seconds, and ends at the
onset of 10 contiguous seconds with no severely-errored
seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 9 }
adsl2PMLCurr15MUas OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this
interval. Unavailability begins at the onset of 10
contiguous severely-errored seconds, and ends at the
onset of 10 contiguous seconds with no severely-errored
seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 9 }
adsl2PMLCurr1DayValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMLineCurrEntry 10 }
adsl2PMLCurr1DayValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMLineCurrEntry 10 }
adsl2PMLCurr1DayInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMLineCurrEntry 11 }
adsl2PMLCurr1DayInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMLineCurrEntry 11 }
adsl2PMLCurr1DayTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only
ADSL2PMLCurr1DayTimeAppeased对象类型语法HCPerfTimeAppeased UNITS“seconds”MAX-ACCESS只读
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLineCurrEntry 12 }
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLineCurrEntry 12 }
adsl2PMLCurr1DayFecs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 13 }
adsl2PMLCurr1DayFecs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 13 }
adsl2PMLCurr1DayEs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 14 }
adsl2PMLCurr1DayEs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 14 }
adsl2PMLCurr1DaySes OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
adsl2PMLCurr1DaySes OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 15 }
::= { adsl2PMLineCurrEntry 15 }
adsl2PMLCurr1DayLoss OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was LOS (or
LOS-FE for ATU-R)."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 16 }
adsl2PMLCurr1DayLoss OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was LOS (or
LOS-FE for ATU-R)."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 16 }
adsl2PMLCurr1DayUas OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely-
errored seconds, and ends at the onset of 10 contiguous
seconds with no severely-errored seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 17 }
adsl2PMLCurr1DayUas OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely-
errored seconds, and ends at the onset of 10 contiguous
seconds with no severely-errored seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 17 }
------------------------------------------------
-- PM line init current counters --
------------------------------------------------
------------------------------------------------
-- PM line init current counters --
------------------------------------------------
adsl2PMLineCurrInitTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineCurrInitEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineCurrInitTable contains current
initialization counters of the ADSL2 line.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLine 2 }
adsl2PMLineCurrInitTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineCurrInitEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineCurrInitTable contains current
initialization counters of the ADSL2 line.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLine 2 }
adsl2PMLineCurrInitEntry OBJECT-TYPE SYNTAX Adsl2PMLineCurrInitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION
adsl2PMLineCurrInitEntry对象类型语法adsl2PMLineCurrInitEntry MAX-ACCESS不可访问状态当前说明
"The table adsl2PMLineCurrInitTable contains current
initialization counters of the ADSL2 line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), and a
termination unit."
INDEX { ifIndex }
::= { adsl2PMLineCurrInitTable 1 }
"The table adsl2PMLineCurrInitTable contains current
initialization counters of the ADSL2 line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), and a
termination unit."
INDEX { ifIndex }
::= { adsl2PMLineCurrInitTable 1 }
Adsl2PMLineCurrInitEntry ::=
SEQUENCE {
adsl2PMLCurrInit15MTimeElapsed Unsigned32,
adsl2PMLCurrInit15MFullInits Unsigned32,
adsl2PMLCurrInit15MFailedFullInits Unsigned32,
adsl2PMLCurrInit15MShortInits Unsigned32,
adsl2PMLCurrInit15MFailedShortInits Unsigned32,
adsl2PMLCurrInit1DayTimeElapsed Unsigned32,
adsl2PMLCurrInit1DayFullInits Unsigned32,
adsl2PMLCurrInit1DayFailedFullInits Unsigned32,
adsl2PMLCurrInit1DayShortInits Unsigned32,
adsl2PMLCurrInit1DayFailedShortInits Unsigned32
}
Adsl2PMLineCurrInitEntry ::=
SEQUENCE {
adsl2PMLCurrInit15MTimeElapsed Unsigned32,
adsl2PMLCurrInit15MFullInits Unsigned32,
adsl2PMLCurrInit15MFailedFullInits Unsigned32,
adsl2PMLCurrInit15MShortInits Unsigned32,
adsl2PMLCurrInit15MFailedShortInits Unsigned32,
adsl2PMLCurrInit1DayTimeElapsed Unsigned32,
adsl2PMLCurrInit1DayFullInits Unsigned32,
adsl2PMLCurrInit1DayFailedFullInits Unsigned32,
adsl2PMLCurrInit1DayShortInits Unsigned32,
adsl2PMLCurrInit1DayFailedShortInits Unsigned32
}
adsl2PMLCurrInit15MTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLineCurrInitEntry 1 }
adsl2PMLCurrInit15MTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLineCurrInitEntry 1 }
adsl2PMLCurrInit15MFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 2 }
adsl2PMLCurrInit15MFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 2 }
adsl2PMLCurrInit15MFailedFullInits OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current
adsl2PMLCurrInit15MFailedFullInits对象类型语法Unsigned32 MAX-ACCESS只读状态当前
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 3 }
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 3 }
adsl2PMLCurrInit15MShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 4 }
adsl2PMLCurrInit15MShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 4 }
adsl2PMLCurrInit15MFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 5 }
adsl2PMLCurrInit15MFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 5 }
adsl2PMLCurrInit1DayTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLineCurrInitEntry 6 }
adsl2PMLCurrInit1DayTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLineCurrInitEntry 6 }
adsl2PMLCurrInit1DayFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 7 }
adsl2PMLCurrInit1DayFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 7 }
adsl2PMLCurrInit1DayFailedFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 8 }
adsl2PMLCurrInit1DayFailedFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 8 }
adsl2PMLCurrInit1DayShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 9 }
adsl2PMLCurrInit1DayShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 9 }
adsl2PMLCurrInit1DayFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 10 }
adsl2PMLCurrInit1DayFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 10 }
-------------------------------------------
-- PM line history 15 Minutes --
-------------------------------------------
adsl2PMLineHist15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineHist15MinTable contains PM line history
for 15min intervals of the ADSL2 line."
::= { adsl2PMLine 3 }
-------------------------------------------
-- PM line history 15 Minutes --
-------------------------------------------
adsl2PMLineHist15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineHist15MinTable contains PM line history
for 15min intervals of the ADSL2 line."
::= { adsl2PMLine 3 }
adsl2PMLineHist15MinEntry OBJECT-TYPE SYNTAX Adsl2PMLineHist15MinEntry MAX-ACCESS not-accessible STATUS current
ADSL2PMLINEHIST15Mentry对象类型语法ADSL2PMLINEHIST15Mentry MAX-ACCESS不可访问状态当前
DESCRIPTION
"The table adsl2PMLineHist15MinTable contains PM line history
for 15min intervals of the ADSL2 line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), along with a
termination unit, and an interval number."
INDEX { ifIndex,
adsl2PMLHist15MUnit,
adsl2PMLHist15MInterval }
::= { adsl2PMLineHist15MinTable 1 }
DESCRIPTION
"The table adsl2PMLineHist15MinTable contains PM line history
for 15min intervals of the ADSL2 line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), along with a
termination unit, and an interval number."
INDEX { ifIndex,
adsl2PMLHist15MUnit,
adsl2PMLHist15MInterval }
::= { adsl2PMLineHist15MinTable 1 }
Adsl2PMLineHist15MinEntry ::=
SEQUENCE {
adsl2PMLHist15MUnit Adsl2Unit,
adsl2PMLHist15MInterval Unsigned32,
adsl2PMLHist15MMonitoredTime Unsigned32,
adsl2PMLHist15MFecs Counter32,
adsl2PMLHist15MEs Counter32,
adsl2PMLHist15MSes Counter32,
adsl2PMLHist15MLoss Counter32,
adsl2PMLHist15MUas Counter32,
adsl2PMLHist15MValidInterval TruthValue
}
Adsl2PMLineHist15MinEntry ::=
SEQUENCE {
adsl2PMLHist15MUnit Adsl2Unit,
adsl2PMLHist15MInterval Unsigned32,
adsl2PMLHist15MMonitoredTime Unsigned32,
adsl2PMLHist15MFecs Counter32,
adsl2PMLHist15MEs Counter32,
adsl2PMLHist15MSes Counter32,
adsl2PMLHist15MLoss Counter32,
adsl2PMLHist15MUas Counter32,
adsl2PMLHist15MValidInterval TruthValue
}
adsl2PMLHist15MUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit atuc(1) or atur(2)."
::= { adsl2PMLineHist15MinEntry 1 }
adsl2PMLHist15MUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit atuc(1) or atur(2)."
::= { adsl2PMLineHist15MinEntry 1 }
adsl2PMLHist15MInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineHist15MinEntry 2 }
adsl2PMLHist15MInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineHist15MinEntry 2 }
adsl2PMLHist15MMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineHist15MinEntry 3 }
adsl2PMLHist15MMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineHist15MinEntry 3 }
adsl2PMLHist15MFecs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 4 }
adsl2PMLHist15MFecs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 4 }
adsl2PMLHist15MEs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 5 }
adsl2PMLHist15MEs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 5 }
adsl2PMLHist15MSes OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 6 }
adsl2PMLHist15MSes OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 6 }
adsl2PMLHist15MLoss OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION
ADSL2PMLIST15MLOSS对象类型语法计数器32个单位“秒”最大访问只读状态当前说明
"Count of seconds during this interval where there was LOS (or
LOS-FE for ATU-R)."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 7 }
"Count of seconds during this interval where there was LOS (or
LOS-FE for ATU-R)."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 7 }
adsl2PMLHist15MUas OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely-
errored seconds, and ends at the onset of 10 contiguous
seconds with no severely-errored seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 8 }
adsl2PMLHist15MUas OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely-
errored seconds, and ends at the onset of 10 contiguous
seconds with no severely-errored seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 8 }
adsl2PMLHist15MValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMLineHist15MinEntry 9 }
adsl2PMLHist15MValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMLineHist15MinEntry 9 }
---------------------------------------
-- PM line history 1 Day --
---------------------------------------
adsl2PMLineHist1DayTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineHist1DayTable contains PM line history
for 24-hour intervals of the ADSL2 line."
::= { adsl2PMLine 4 }
---------------------------------------
-- PM line history 1 Day --
---------------------------------------
adsl2PMLineHist1DayTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineHist1DayTable contains PM line history
for 24-hour intervals of the ADSL2 line."
::= { adsl2PMLine 4 }
adsl2PMLineHist1DayEntry OBJECT-TYPE SYNTAX Adsl2PMLineHist1DayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2PMLineHist1DayTable contains PM line history for 24-hour intervals of the ADSL2 line.
adsl2PMLineHist1DayEntry对象类型语法adsl2PMLineHist1DayEntry MAX-ACCESS不可访问状态当前描述“表adsl2PMLineHist1DayTable包含ADSL2线路24小时间隔的PM线路历史记录。
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), along with a
termination unit, and an interval number."
INDEX { ifIndex,
adsl2PMLHist1DUnit,
adsl2PMLHist1DInterval }
::= { adsl2PMLineHist1DayTable 1 }
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), along with a
termination unit, and an interval number."
INDEX { ifIndex,
adsl2PMLHist1DUnit,
adsl2PMLHist1DInterval }
::= { adsl2PMLineHist1DayTable 1 }
Adsl2PMLineHist1DayEntry ::=
SEQUENCE {
adsl2PMLHist1DUnit Adsl2Unit,
adsl2PMLHist1DInterval Unsigned32,
adsl2PMLHist1DMonitoredTime Unsigned32,
adsl2PMLHist1DFecs Counter32,
adsl2PMLHist1DEs Counter32,
adsl2PMLHist1DSes Counter32,
adsl2PMLHist1DLoss Counter32,
adsl2PMLHist1DUas Counter32,
adsl2PMLHist1DValidInterval TruthValue
}
Adsl2PMLineHist1DayEntry ::=
SEQUENCE {
adsl2PMLHist1DUnit Adsl2Unit,
adsl2PMLHist1DInterval Unsigned32,
adsl2PMLHist1DMonitoredTime Unsigned32,
adsl2PMLHist1DFecs Counter32,
adsl2PMLHist1DEs Counter32,
adsl2PMLHist1DSes Counter32,
adsl2PMLHist1DLoss Counter32,
adsl2PMLHist1DUas Counter32,
adsl2PMLHist1DValidInterval TruthValue
}
adsl2PMLHist1DUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMLineHist1DayEntry 1 }
adsl2PMLHist1DUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMLineHist1DayEntry 1 }
adsl2PMLHist1DInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineHist1DayEntry 2 }
adsl2PMLHist1DInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineHist1DayEntry 2 }
adsl2PMLHist1DMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineHist1DayEntry 3 }
adsl2PMLHist1DMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineHist1DayEntry 3 }
adsl2PMLHist1DFecs OBJECT-TYPE SYNTAX Counter32
ADSL2PMLIST1DFECS对象类型语法计数器32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 4 }
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 4 }
adsl2PMLHist1DEs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 5 }
adsl2PMLHist1DEs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 5 }
adsl2PMLHist1DSes OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >> 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 6 }
adsl2PMLHist1DSes OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >> 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 6 }
adsl2PMLHist1DLoss OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds during this interval where there was LOS (or LOS-FE for ATU-R)."
ADSL2PMLIST1DLOSS对象类型语法计数器32个单位“秒”最大访问只读状态当前描述“在有服务水平（或ATU-R的服务水平FE）的时间间隔内的秒数。”
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 7 }
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 7 }
adsl2PMLHist1DUas OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely-
errored seconds, and ends at the onset of 10 contiguous
seconds with no severely-errored seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 8 }
adsl2PMLHist1DUas OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely-
errored seconds, and ends at the onset of 10 contiguous
seconds with no severely-errored seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 8 }
adsl2PMLHist1DValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMLineHist1DayEntry 9 }
adsl2PMLHist1DValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMLineHist1DayEntry 9 }
-------------------------------------------
-- PM line init history 15 Minutes --
-------------------------------------------
-------------------------------------------
-- PM line init history 15 Minutes --
-------------------------------------------
adsl2PMLineInitHist15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineInitHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineInitHist15MinTable contains PM line
initialization history for 15-minute intervals of the ADSL2
line."
::= { adsl2PMLine 5 }
adsl2PMLineInitHist15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineInitHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineInitHist15MinTable contains PM line
initialization history for 15-minute intervals of the ADSL2
line."
::= { adsl2PMLine 5 }
adsl2PMLineInitHist15MinEntry OBJECT-TYPE SYNTAX Adsl2PMLineInitHist15MinEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2PMLineInitHist15MinTable contains PM line
ADSL2PMLINEINTHIST15大陆对象类型语法ADSL2PMLINEINTHIST15大陆MAX-ACCESS不可访问状态当前说明“表ADSL2PMLINEINTHIST15维护包含PM行
initialization history for 15 minutes intervals of the ADSL2
line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), and an interval
number."
INDEX { ifIndex,
adsl2PMLHistInit15MInterval }
::= { adsl2PMLineInitHist15MinTable 1 }
initialization history for 15 minutes intervals of the ADSL2
line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), and an interval
number."
INDEX { ifIndex,
adsl2PMLHistInit15MInterval }
::= { adsl2PMLineInitHist15MinTable 1 }
Adsl2PMLineInitHist15MinEntry ::=
SEQUENCE {
adsl2PMLHistInit15MInterval Unsigned32,
adsl2PMLHistInit15MMonitoredTime Unsigned32,
adsl2PMLHistInit15MFullInits Unsigned32,
adsl2PMLHistInit15MFailedFullInits Unsigned32,
adsl2PMLHistInit15MShortInits Unsigned32,
adsl2PMLHistInit15MFailedShortInits Unsigned32,
adsl2PMLHistInit15MValidInterval TruthValue
}
Adsl2PMLineInitHist15MinEntry ::=
SEQUENCE {
adsl2PMLHistInit15MInterval Unsigned32,
adsl2PMLHistInit15MMonitoredTime Unsigned32,
adsl2PMLHistInit15MFullInits Unsigned32,
adsl2PMLHistInit15MFailedFullInits Unsigned32,
adsl2PMLHistInit15MShortInits Unsigned32,
adsl2PMLHistInit15MFailedShortInits Unsigned32,
adsl2PMLHistInit15MValidInterval TruthValue
}
adsl2PMLHistInit15MInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineInitHist15MinEntry 1 }
adsl2PMLHistInit15MInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineInitHist15MinEntry 1 }
adsl2PMLHistInit15MMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineInitHist15MinEntry 2 }
adsl2PMLHistInit15MMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineInitHist15MinEntry 2 }
adsl2PMLHistInit15MFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist15MinEntry 3 }
adsl2PMLHistInit15MFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist15MinEntry 3 }
adsl2PMLHistInit15MFailedFullInits OBJECT-TYPE
adsl2PMLHistInit15MFailedFullInits对象类型
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist15MinEntry 4 }
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist15MinEntry 4 }
adsl2PMLHistInit15MShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist15MinEntry 5 }
adsl2PMLHistInit15MShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist15MinEntry 5 }
adsl2PMLHistInit15MFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist15MinEntry 6 }
adsl2PMLHistInit15MFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist15MinEntry 6 }
adsl2PMLHistInit15MValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMLineInitHist15MinEntry 7 }
adsl2PMLHistInit15MValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMLineInitHist15MinEntry 7 }
-------------------------------------------
-- PM line init history 1 Day --
-------------------------------------------
adsl2PMLineInitHist1DayTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineInitHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
-------------------------------------------
-- PM line init history 1 Day --
-------------------------------------------
adsl2PMLineInitHist1DayTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineInitHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineInitHist1DayTable contains PM line
initialization history for 24-hour intervals of the ADSL2
line."
::= { adsl2PMLine 6 }
"The table adsl2PMLineInitHist1DayTable contains PM line
initialization history for 24-hour intervals of the ADSL2
line."
::= { adsl2PMLine 6 }
adsl2PMLineInitHist1DayEntry OBJECT-TYPE
SYNTAX Adsl2PMLineInitHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineInitHist1DayTable contains PM line
initialization history for 24-hour intervals of the ADSL2
line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), and an interval
number."
INDEX { ifIndex,
adsl2PMLHistinit1DInterval }
::= { adsl2PMLineInitHist1DayTable 1 }
adsl2PMLineInitHist1DayEntry OBJECT-TYPE
SYNTAX Adsl2PMLineInitHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineInitHist1DayTable contains PM line
initialization history for 24-hour intervals of the ADSL2
line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), and an interval
number."
INDEX { ifIndex,
adsl2PMLHistinit1DInterval }
::= { adsl2PMLineInitHist1DayTable 1 }
Adsl2PMLineInitHist1DayEntry ::=
SEQUENCE {
adsl2PMLHistinit1DInterval Unsigned32,
adsl2PMLHistinit1DMonitoredTime Unsigned32,
adsl2PMLHistinit1DFullInits Unsigned32,
adsl2PMLHistinit1DFailedFullInits Unsigned32,
adsl2PMLHistinit1DShortInits Unsigned32,
adsl2PMLHistinit1DFailedShortInits Unsigned32,
adsl2PMLHistinit1DValidInterval TruthValue
}
Adsl2PMLineInitHist1DayEntry ::=
SEQUENCE {
adsl2PMLHistinit1DInterval Unsigned32,
adsl2PMLHistinit1DMonitoredTime Unsigned32,
adsl2PMLHistinit1DFullInits Unsigned32,
adsl2PMLHistinit1DFailedFullInits Unsigned32,
adsl2PMLHistinit1DShortInits Unsigned32,
adsl2PMLHistinit1DFailedShortInits Unsigned32,
adsl2PMLHistinit1DValidInterval TruthValue
}
adsl2PMLHistinit1DInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineInitHist1DayEntry 1 }
adsl2PMLHistinit1DInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineInitHist1DayEntry 1 }
adsl2PMLHistinit1DMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineInitHist1DayEntry 2 }
adsl2PMLHistinit1DMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineInitHist1DayEntry 2 }
adsl2PMLHistinit1DFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist1DayEntry 3 }
adsl2PMLHistinit1DFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist1DayEntry 3 }
adsl2PMLHistinit1DFailedFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist1DayEntry 4 }
adsl2PMLHistinit1DFailedFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist1DayEntry 4 }
adsl2PMLHistinit1DShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist1DayEntry 5 }
adsl2PMLHistinit1DShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist1DayEntry 5 }
adsl2PMLHistinit1DFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist1DayEntry 6 }
adsl2PMLHistinit1DFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist1DayEntry 6 }
adsl2PMLHistinit1DValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMLineInitHist1DayEntry 7 }
adsl2PMLHistinit1DValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMLineInitHist1DayEntry 7 }
---------------------------------------------------
-- PM channel current counters --
---------------------------------------------------
adsl2PMChCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMChCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMChannel 1 }
---------------------------------------------------
-- PM channel current counters --
---------------------------------------------------
adsl2PMChCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMChCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMChannel 1 }
adsl2PMChCurrEntry OBJECT-TYPE
SYNTAX Adsl2PMChCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a DSL channel, along with a termination unit."
INDEX { ifIndex, adsl2PMChCurrUnit }
::= { adsl2PMChCurrTable 1 }
adsl2PMChCurrEntry OBJECT-TYPE
SYNTAX Adsl2PMChCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a DSL channel, along with a termination unit."
INDEX { ifIndex, adsl2PMChCurrUnit }
::= { adsl2PMChCurrTable 1 }
Adsl2PMChCurrEntry ::=
SEQUENCE {
adsl2PMChCurrUnit Adsl2Unit,
adsl2PMChCurrValidIntervals Unsigned32,
adsl2PMChCurrInvalidIntervals Unsigned32,
adsl2PMChCurr15MTimeElapsed HCPerfTimeElapsed,
adsl2PMChCurr15MCodingViolations Unsigned32,
adsl2PMChCurr15MCorrectedBlocks Unsigned32,
adsl2PMChCurr1DayValidIntervals Unsigned32,
adsl2PMChCurr1DayInvalidIntervals Unsigned32,
adsl2PMChCurr1DayTimeElapsed HCPerfTimeElapsed,
adsl2PMChCurr1DayCodingViolations Unsigned32,
adsl2PMChCurr1DayCorrectedBlocks Unsigned32
}
Adsl2PMChCurrEntry ::=
SEQUENCE {
adsl2PMChCurrUnit Adsl2Unit,
adsl2PMChCurrValidIntervals Unsigned32,
adsl2PMChCurrInvalidIntervals Unsigned32,
adsl2PMChCurr15MTimeElapsed HCPerfTimeElapsed,
adsl2PMChCurr15MCodingViolations Unsigned32,
adsl2PMChCurr15MCorrectedBlocks Unsigned32,
adsl2PMChCurr1DayValidIntervals Unsigned32,
adsl2PMChCurr1DayInvalidIntervals Unsigned32,
adsl2PMChCurr1DayTimeElapsed HCPerfTimeElapsed,
adsl2PMChCurr1DayCodingViolations Unsigned32,
adsl2PMChCurr1DayCorrectedBlocks Unsigned32
}
adsl2PMChCurrUnit OBJECT-TYPE SYNTAX Adsl2Unit MAX-ACCESS not-accessible STATUS current DESCRIPTION
adsl2PMChCurrUnit对象类型语法Adsl2Unit MAX-ACCESS不可访问状态当前说明
"The termination unit."
::= { adsl2PMChCurrEntry 1 }
"The termination unit."
::= { adsl2PMChCurrEntry 1 }
adsl2PMChCurrValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMChCurrEntry 2 }
adsl2PMChCurrValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMChCurrEntry 2 }
adsl2PMChCurrInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMChCurrEntry 3 }
adsl2PMChCurrInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMChCurrEntry 3 }
adsl2PMChCurr15MTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMChCurrEntry 4 }
adsl2PMChCurr15MTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMChCurrEntry 4 }
adsl2PMChCurr15MCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the
channel during the interval. This parameter is inhibited
during UAS or SES. If the CRC is applied over multiple
channels, then each related CRC-8 (or FEBE) anomaly should
increment each of the counters related to the individual
channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChCurrEntry 5 }
adsl2PMChCurr15MCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the
channel during the interval. This parameter is inhibited
during UAS or SES. If the CRC is applied over multiple
channels, then each related CRC-8 (or FEBE) anomaly should
increment each of the counters related to the individual
channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChCurrEntry 5 }
adsl2PMChCurr15MCorrectedBlocks OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only
adsl2PMChCurr15MCorrectedBlocks对象类型语法Unsigned32 MAX-ACCESS只读
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChCurrEntry 6 }
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChCurrEntry 6 }
adsl2PMChCurr1DayValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMChCurrEntry 7 }
adsl2PMChCurr1DayValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMChCurrEntry 7 }
adsl2PMChCurr1DayInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMChCurrEntry 8 }
adsl2PMChCurr1DayInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMChCurrEntry 8 }
adsl2PMChCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMChCurrEntry 9 }
adsl2PMChCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMChCurrEntry 9 }
adsl2PMChCurr1DayCodingViolations OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should
ADSL2PMCHCURR1DAYCODINGVICTIONS对象类型语法无符号32 MAX-ACCESS只读状态当前描述“在间隔期间发生在通道中的CRC-8（FEBE用于ATU-R）异常计数。此参数在UAS或SES期间被禁用。如果CRC应用于多个通道，则每个相关的CRC-8（或FEBE）异常应
increment each of the counters related to the individual
channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChCurrEntry 10 }
increment each of the counters related to the individual
channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChCurrEntry 10 }
adsl2PMChCurr1DayCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChCurrEntry 11 }
adsl2PMChCurr1DayCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChCurrEntry 11 }
-------------------------------------------
-- PM channel history 15 Minutes --
-------------------------------------------
adsl2PMChHist15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMChHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel."
::= { adsl2PMChannel 2 }
-------------------------------------------
-- PM channel history 15 Minutes --
-------------------------------------------
adsl2PMChHist15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMChHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel."
::= { adsl2PMChannel 2 }
adsl2PMChHist15MinEntry OBJECT-TYPE
SYNTAX Adsl2PMChHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a DSL channel, along with a termination unit, and the
interval number."
INDEX { ifIndex,
adsl2PMChHist15MUnit,
adsl2PMChHist15MInterval }
::= { adsl2PMChHist15MinTable 1 }
adsl2PMChHist15MinEntry OBJECT-TYPE
SYNTAX Adsl2PMChHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a DSL channel, along with a termination unit, and the
interval number."
INDEX { ifIndex,
adsl2PMChHist15MUnit,
adsl2PMChHist15MInterval }
::= { adsl2PMChHist15MinTable 1 }
Adsl2PMChHist15MinEntry ::=
SEQUENCE {
adsl2PMChHist15MUnit Adsl2Unit,
adsl2PMChHist15MInterval Unsigned32,
adsl2PMChHist15MMonitoredTime Unsigned32,
adsl2PMChHist15MCodingViolations Unsigned32,
adsl2PMChHist15MCorrectedBlocks Unsigned32,
adsl2PMChHist15MValidInterval TruthValue
}
Adsl2PMChHist15MinEntry ::=
SEQUENCE {
adsl2PMChHist15MUnit Adsl2Unit,
adsl2PMChHist15MInterval Unsigned32,
adsl2PMChHist15MMonitoredTime Unsigned32,
adsl2PMChHist15MCodingViolations Unsigned32,
adsl2PMChHist15MCorrectedBlocks Unsigned32,
adsl2PMChHist15MValidInterval TruthValue
}
adsl2PMChHist15MUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMChHist15MinEntry 1 }
adsl2PMChHist15MUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMChHist15MinEntry 1 }
adsl2PMChHist15MInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMChHist15MinEntry 2 }
adsl2PMChHist15MInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMChHist15MinEntry 2 }
adsl2PMChHist15MMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMChHist15MinEntry 3 }
adsl2PMChHist15MMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMChHist15MinEntry 3 }
adsl2PMChHist15MCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the
channel during the interval. This parameter is inhibited
during UAS or SES. If the CRC is applied over multiple
channels, then each related CRC-8 (or FEBE) anomaly should
increment each of the counters related to the individual
channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChHist15MinEntry 4 }
adsl2PMChHist15MCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the
channel during the interval. This parameter is inhibited
during UAS or SES. If the CRC is applied over multiple
channels, then each related CRC-8 (or FEBE) anomaly should
increment each of the counters related to the individual
channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChHist15MinEntry 4 }
adsl2PMChHist15MCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChHist15MinEntry 5 }
adsl2PMChHist15MCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChHist15MinEntry 5 }
adsl2PMChHist15MValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMChHist15MinEntry 6 }
adsl2PMChHist15MValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMChHist15MinEntry 6 }
------------------------------------------
-- PM channel history 1 Day --
------------------------------------------
adsl2PMChHist1DTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMChHist1DEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChHist1DayTable contains PM channel history
for 1-day intervals of ADSL2."
::= { adsl2PMChannel 3 }
------------------------------------------
-- PM channel history 1 Day --
------------------------------------------
adsl2PMChHist1DTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMChHist1DEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChHist1DayTable contains PM channel history
for 1-day intervals of ADSL2."
::= { adsl2PMChannel 3 }
adsl2PMChHist1DEntry OBJECT-TYPE SYNTAX Adsl2PMChHist1DEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2PMChHist1DayTable contains PM channel history for 1-day intervals of ADSL2. The index of this table consists of an interface index, where the interface has an ifType value that is applicable for a DSL channel, along with a termination unit, and the interval number."
adsl2PMChHist1DEntry对象类型语法adsl2PMChHist1DEntry MAX-ACCESS不可访问状态当前说明“表adsl2PMChHist1DayTable包含ADSL2 1天间隔的PM信道历史记录。此表的索引由接口索引组成，其中接口具有适用于DSL信道的ifType值、终端单元和间隔号。”
INDEX { ifIndex,
adsl2PMChHist1DUnit,
adsl2PMChHist1DInterval }
::= { adsl2PMChHist1DTable 1 }
INDEX { ifIndex,
adsl2PMChHist1DUnit,
adsl2PMChHist1DInterval }
::= { adsl2PMChHist1DTable 1 }
Adsl2PMChHist1DEntry ::=
SEQUENCE {
adsl2PMChHist1DUnit Adsl2Unit,
adsl2PMChHist1DInterval Unsigned32,
adsl2PMChHist1DMonitoredTime Unsigned32,
adsl2PMChHist1DCodingViolations Unsigned32,
adsl2PMChHist1DCorrectedBlocks Unsigned32,
adsl2PMChHist1DValidInterval TruthValue
}
Adsl2PMChHist1DEntry ::=
SEQUENCE {
adsl2PMChHist1DUnit Adsl2Unit,
adsl2PMChHist1DInterval Unsigned32,
adsl2PMChHist1DMonitoredTime Unsigned32,
adsl2PMChHist1DCodingViolations Unsigned32,
adsl2PMChHist1DCorrectedBlocks Unsigned32,
adsl2PMChHist1DValidInterval TruthValue
}
adsl2PMChHist1DUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMChHist1DEntry 1 }
adsl2PMChHist1DUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMChHist1DEntry 1 }
adsl2PMChHist1DInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMChHist1DEntry 2 }
adsl2PMChHist1DInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMChHist1DEntry 2 }
adsl2PMChHist1DMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMChHist1DEntry 3 }
adsl2PMChHist1DMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMChHist1DEntry 3 }
adsl2PMChHist1DCodingViolations OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple
ADSL2PMCHHIST1DCODINGINVICERS对象类型语法Unsigned32 MAX-ACCESS只读状态当前描述“间隔期间通道中发生的CRC-8（ATU-R的FEBE）异常计数。此参数在UAS或SES期间被禁用。如果CRC应用于多个
channels, then each related CRC-8 (or FEBE) anomaly should
increment each of the counters related to the individual
channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChHist1DEntry 4 }
channels, then each related CRC-8 (or FEBE) anomaly should
increment each of the counters related to the individual
channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChHist1DEntry 4 }
adsl2PMChHist1DCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChHist1DEntry 5 }
adsl2PMChHist1DCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChHist1DEntry 5 }
adsl2PMChHist1DValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMChHist1DEntry 6 }
adsl2PMChHist1DValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMChHist1DEntry 6 }
-------------------------------------------
-- Notifications Group --
-------------------------------------------
-------------------------------------------
-- Notifications Group --
-------------------------------------------
adsl2LinePerfFECSThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MFecs,
adsl2LineAlarmConfProfileAtucThresh15MinFecs
}
STATUS current
DESCRIPTION
"This notification indicates that the FEC seconds threshold
has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 1 }
adsl2LinePerfFECSThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MFecs,
adsl2LineAlarmConfProfileAtucThresh15MinFecs
}
STATUS current
DESCRIPTION
"This notification indicates that the FEC seconds threshold
has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 1 }
adsl2LinePerfFECSThreshAtur NOTIFICATION-TYPE OBJECTS {
ADSL2LINEPERFECTHRESHATUR通知类型对象{
adsl2PMLCurr15MFecs,
adsl2LineAlarmConfProfileAturThresh15MinFecs
}
STATUS current
DESCRIPTION
"This notification indicates that the FEC seconds threshold
has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 2 }
adsl2PMLCurr15MFecs,
adsl2LineAlarmConfProfileAturThresh15MinFecs
}
STATUS current
DESCRIPTION
"This notification indicates that the FEC seconds threshold
has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 2 }
adsl2LinePerfESThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MEs,
adsl2LineAlarmConfProfileAtucThresh15MinEs
}
STATUS current
DESCRIPTION
"This notification indicates that the errored seconds threshold
has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 3 }
adsl2LinePerfESThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MEs,
adsl2LineAlarmConfProfileAtucThresh15MinEs
}
STATUS current
DESCRIPTION
"This notification indicates that the errored seconds threshold
has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 3 }
adsl2LinePerfESThreshAtur NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MEs,
adsl2LineAlarmConfProfileAturThresh15MinEs
}
STATUS current
DESCRIPTION
"This notification indicates that the errored seconds threshold
has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 4 }
adsl2LinePerfESThreshAtur NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MEs,
adsl2LineAlarmConfProfileAturThresh15MinEs
}
STATUS current
DESCRIPTION
"This notification indicates that the errored seconds threshold
has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 4 }
adsl2LinePerfSESThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MSes,
adsl2LineAlarmConfProfileAtucThresh15MinSes
}
STATUS current
DESCRIPTION
"This notification indicates that the severely-errored seconds
threshold has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 5 }
adsl2LinePerfSESThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MSes,
adsl2LineAlarmConfProfileAtucThresh15MinSes
}
STATUS current
DESCRIPTION
"This notification indicates that the severely-errored seconds
threshold has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 5 }
adsl2LinePerfSESThreshAtur NOTIFICATION-TYPE OBJECTS {
ADSL2LINEPERFESSESTHERATUR通知类型对象{
adsl2PMLCurr15MSes,
adsl2LineAlarmConfProfileAturThresh15MinSes
}
STATUS current
DESCRIPTION
"This notification indicates that the severely-errored seconds
threshold has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 6 }
adsl2PMLCurr15MSes,
adsl2LineAlarmConfProfileAturThresh15MinSes
}
STATUS current
DESCRIPTION
"This notification indicates that the severely-errored seconds
threshold has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 6 }
adsl2LinePerfLOSSThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MLoss,
adsl2LineAlarmConfProfileAtucThresh15MinLoss
}
STATUS current
DESCRIPTION
"This notification indicates that the LOS seconds
threshold has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 7 }
adsl2LinePerfLOSSThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MLoss,
adsl2LineAlarmConfProfileAtucThresh15MinLoss
}
STATUS current
DESCRIPTION
"This notification indicates that the LOS seconds
threshold has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 7 }
adsl2LinePerfLOSSThreshAtur NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MLoss,
adsl2LineAlarmConfProfileAturThresh15MinLoss
}
STATUS current
DESCRIPTION
"This notification indicates that the LOS seconds
threshold has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 8 }
adsl2LinePerfLOSSThreshAtur NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MLoss,
adsl2LineAlarmConfProfileAturThresh15MinLoss
}
STATUS current
DESCRIPTION
"This notification indicates that the LOS seconds
threshold has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 8 }
adsl2LinePerfUASThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MUas,
adsl2LineAlarmConfProfileAtucThresh15MinUas
}
STATUS current
DESCRIPTION
"This notification indicates that the unavailable seconds
threshold has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 9 }
adsl2LinePerfUASThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurr15MUas,
adsl2LineAlarmConfProfileAtucThresh15MinUas
}
STATUS current
DESCRIPTION
"This notification indicates that the unavailable seconds
threshold has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 9 }
adsl2LinePerfUASThreshAtur NOTIFICATION-TYPE OBJECTS {
ADSL2LINEPRESHATUR通知类型对象{
adsl2PMLCurr15MUas,
adsl2LineAlarmConfProfileAturThresh15MinUas
}
STATUS current
DESCRIPTION
"This notification indicates that the unavailable seconds
threshold has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 10 }
adsl2PMLCurr15MUas,
adsl2LineAlarmConfProfileAturThresh15MinUas
}
STATUS current
DESCRIPTION
"This notification indicates that the unavailable seconds
threshold has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 10 }
adsl2LinePerfCodingViolationsThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMChCurr15MCodingViolations,
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations
}
STATUS current
DESCRIPTION
"This notification indicates that the coding violations
threshold has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 11 }
adsl2LinePerfCodingViolationsThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMChCurr15MCodingViolations,
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations
}
STATUS current
DESCRIPTION
"This notification indicates that the coding violations
threshold has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 11 }
adsl2LinePerfCodingViolationsThreshAtur NOTIFICATION-TYPE
OBJECTS
{
adsl2PMChCurr15MCodingViolations,
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations
}
STATUS current
DESCRIPTION
"This notification indicates that the coding violations
threshold has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 12 }
adsl2LinePerfCodingViolationsThreshAtur NOTIFICATION-TYPE
OBJECTS
{
adsl2PMChCurr15MCodingViolations,
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations
}
STATUS current
DESCRIPTION
"This notification indicates that the coding violations
threshold has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 12 }
adsl2LinePerfCorrectedThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMChCurr15MCorrectedBlocks,
adsl2ChAlarmConfProfileAtucThresh15MinCorrected
}
STATUS current
DESCRIPTION
"This notification indicates that the corrected blocks
(FEC events) threshold has been reached/exceeded for the
referred ATU-C."
::= { adsl2Notifications 13 }
adsl2LinePerfCorrectedThreshAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2PMChCurr15MCorrectedBlocks,
adsl2ChAlarmConfProfileAtucThresh15MinCorrected
}
STATUS current
DESCRIPTION
"This notification indicates that the corrected blocks
(FEC events) threshold has been reached/exceeded for the
referred ATU-C."
::= { adsl2Notifications 13 }
adsl2LinePerfCorrectedThreshAtur NOTIFICATION-TYPE OBJECTS
ADSL2LinePerformedThreshatur通知类型对象
{
adsl2PMChCurr15MCorrectedBlocks,
adsl2ChAlarmConfProfileAturThresh15MinCorrected
}
STATUS current
DESCRIPTION
"This notification indicates that the corrected blocks
(FEC events) threshold has been reached/exceeded for the
referred ATU-R."
::= { adsl2Notifications 14 }
{
adsl2PMChCurr15MCorrectedBlocks,
adsl2ChAlarmConfProfileAturThresh15MinCorrected
}
STATUS current
DESCRIPTION
"This notification indicates that the corrected blocks
(FEC events) threshold has been reached/exceeded for the
referred ATU-R."
::= { adsl2Notifications 14 }
adsl2LinePerfFailedFullInitThresh NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurrInit15MFailedFullInits,
adsl2LineAlarmConfProfileThresh15MinFailedFullInt
}
STATUS current
DESCRIPTION
"This notification indicates that the failed full
initializations threshold has been reached/exceeded for the
referred ADSL/ADSL2 or ADSL2+ line."
::= { adsl2Notifications 15 }
adsl2LinePerfFailedFullInitThresh NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurrInit15MFailedFullInits,
adsl2LineAlarmConfProfileThresh15MinFailedFullInt
}
STATUS current
DESCRIPTION
"This notification indicates that the failed full
initializations threshold has been reached/exceeded for the
referred ADSL/ADSL2 or ADSL2+ line."
::= { adsl2Notifications 15 }
adsl2LinePerfFailedShortInitThresh NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurrInit15MFailedShortInits,
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt
}
STATUS current
DESCRIPTION
"This notification indicates that the failed short
initializations threshold has been reached/exceeded for the
referred ADSL/ADSL2 or ADSL2+ line."
::= { adsl2Notifications 16 }
adsl2LinePerfFailedShortInitThresh NOTIFICATION-TYPE
OBJECTS
{
adsl2PMLCurrInit15MFailedShortInits,
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt
}
STATUS current
DESCRIPTION
"This notification indicates that the failed short
initializations threshold has been reached/exceeded for the
referred ADSL/ADSL2 or ADSL2+ line."
::= { adsl2Notifications 16 }
adsl2LineStatusChangeAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2LineStatusAtuc
}
STATUS current
DESCRIPTION
"This notification indicates that a status change is
detected for the referred ATU-C."
::= { adsl2Notifications 17 }
adsl2LineStatusChangeAtuc NOTIFICATION-TYPE
OBJECTS
{
adsl2LineStatusAtuc
}
STATUS current
DESCRIPTION
"This notification indicates that a status change is
detected for the referred ATU-C."
::= { adsl2Notifications 17 }
adsl2LineStatusChangeAtur NOTIFICATION-TYPE
OBJECTS
{
adsl2LineStatusAtur
}
STATUS current
DESCRIPTION
"This notification indicates that a status change is
detected for the referred ATU-R."
::= { adsl2Notifications 18 }
adsl2LineStatusChangeAtur NOTIFICATION-TYPE
OBJECTS
{
adsl2LineStatusAtur
}
STATUS current
DESCRIPTION
"This notification indicates that a status change is
detected for the referred ATU-R."
::= { adsl2Notifications 18 }
-- conformance information
--一致性信息
adsl2Groups OBJECT IDENTIFIER ::= { adsl2Conformance 1 }
adsl2Compliances OBJECT IDENTIFIER ::= { adsl2Conformance 2 }
adsl2Groups OBJECT IDENTIFIER ::= { adsl2Conformance 1 }
adsl2Compliances OBJECT IDENTIFIER ::= { adsl2Conformance 2 }
adsl2LineMibCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities that
manage ADSL/ADSL2 or ADSL2+ interfaces."
MODULE -- this module
MANDATORY-GROUPS
{
adsl2LineGroup,
adsl2ChannelStatusGroup,
adsl2SCStatusGroup,
adsl2LineInventoryGroup,
adsl2LineConfTemplateGroup,
adsl2LineConfProfGroup,
adsl2LineConfProfModeSpecGroup,
adsl2ChConfProfileGroup,
adsl2LineAlarmConfTemplateGroup,
adsl2PMLineCurrGroup,
adsl2PMLineCurrInitGroup,
adsl2PMLineHist15MinGroup,
adsl2PMLineHist1DayGroup,
adsl2PMLineInitHist15MinGroup,
adsl2PMLineInitHist1DayGroup,
adsl2PMChCurrGroup,
adsl2PMChHist15MinGroup,
adsl2PMChHist1DGroup
}
adsl2LineMibCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities that
manage ADSL/ADSL2 or ADSL2+ interfaces."
MODULE -- this module
MANDATORY-GROUPS
{
adsl2LineGroup,
adsl2ChannelStatusGroup,
adsl2SCStatusGroup,
adsl2LineInventoryGroup,
adsl2LineConfTemplateGroup,
adsl2LineConfProfGroup,
adsl2LineConfProfModeSpecGroup,
adsl2ChConfProfileGroup,
adsl2LineAlarmConfTemplateGroup,
adsl2PMLineCurrGroup,
adsl2PMLineCurrInitGroup,
adsl2PMLineHist15MinGroup,
adsl2PMLineHist1DayGroup,
adsl2PMLineInitHist15MinGroup,
adsl2PMLineInitHist1DayGroup,
adsl2PMChCurrGroup,
adsl2PMChHist15MinGroup,
adsl2PMChHist1DGroup
}
GROUP adsl2ChannelStatusAtmGroup DESCRIPTION "The group of status objects required when the data path
组adsl2ChannelStatusAtmGroup DESCRIPTION“当数据路径
is ATM."
这是自动取款机。”
GROUP adsl2ChannelStatusPtmGroup DESCRIPTION "The group of status objects required when the data path is PTM."
组adsl2ChannelStatusPtmGroup DESCRIPTION“数据路径为PTM时所需的状态对象组。”
GROUP adsl2LineConfProfRaGroup DESCRIPTION "The group of objects required for controlling the rate-adaptive behavior of the line."
GROUP adsl2LineConfProfRaGroup DESCRIPTION“控制线路速率自适应行为所需的对象组。”
GROUP adsl2LineConfProfMsgMinGroup DESCRIPTION "The group of objects required for controlling the rate reserved for Overhead traffic."
GROUP adsl2LineConfProfMsgMinGroup DESCRIPTION“控制为开销通信保留的速率所需的对象组。”
GROUP adsl2LineAlarmConfProfileGroup DESCRIPTION "The group of objects that define the alarm thresholds on line-level PM counters."
GROUP adsl2LineAlarmConfProfileGroup DESCRIPTION“定义线路级PM计数器上的报警阈值的对象组。”
GROUP adsl2ChAlarmConfProfileGroup DESCRIPTION "The group of objects that define the alarm thresholds on channel-level PM counters."
GROUP adsl2ChAlarmConfProfileGroup DESCRIPTION“定义通道级PM计数器上的报警阈值的对象组。”
GROUP adsl2ChConfProfileAtmGroup DESCRIPTION "The group of configuration objects required when the data path is ATM."
组adsl2ChConfProfileAtmGroup DESCRIPTION“数据路径为ATM时所需的配置对象组。”
GROUP adsl2ChConfProfileMinResGroup DESCRIPTION "The group of configuration objects required for the reserved data rate."
组adsl2ChConfProfileMinResGroup DESCRIPTION“保留数据速率所需的配置对象组。”
GROUP adsl2PMLineCurrInitShortGroup DESCRIPTION "The group of PM counters for the current interval's short initializations."
组adsl2PMLineCurrInitShortGroup DESCRIPTION“当前间隔的短初始化的PM计数器组。”
GROUP adsl2PMLineInitHist15MinShortGroup DESCRIPTION "The group of PM counters for the previous 15-minute interval's short initializations."
组adsl2PMLineInitHist15MinShortGroup DESCRIPTION“前15分钟间隔的短初始化的PM计数器组。”
GROUP adsl2PMLineInitHist1DayShortGroup
GROUP adsl2PMLineInitHist1DayShortGroup
DESCRIPTION "The group of PM counters for the previous 24-hour interval's short initializations."
DESCRIPTION“前24小时间隔的短初始化的PM计数器组。”
GROUP adsl2ScalarSCGroup DESCRIPTION "The group of objects that report the available memory resources for DELT processes."
GROUP adsl2ScalarSCGroup DESCRIPTION“报告DELT进程可用内存资源的对象组。”
GROUP adsl2ThreshNotificationGroup DESCRIPTION "The group of threshold crossing notifications."
组ADSL2ThNotificationGroup DESCRIPTION“阈值交叉通知组”
GROUP adsl2StatusChangeNotificationGroup DESCRIPTION "The group of status change notifications."
组adsl2StatusChangeNotificationGroup描述“状态更改通知组”
::= { adsl2Compliances 1 }
::= { adsl2Compliances 1 }
-- units of conformance
--一致性单位
adsl2LineGroup OBJECT-GROUP OBJECTS { adsl2LineCnfgTemplate, adsl2LineAlarmCnfgTemplate, adsl2LineCmndConfPmsf, adsl2LineCmndConfLdsf, adsl2LineCmndConfLdsfFailReason, adsl2LineCmndAutomodeColdStart, adsl2LineStatusAtuTransSys, adsl2LineStatusPwrMngState, adsl2LineStatusInitResult, adsl2LineStatusLastStateDs, adsl2LineStatusLastStateUs, adsl2LineStatusAtur, adsl2LineStatusAtuc, adsl2LineStatusLnAttenDs, adsl2LineStatusLnAttenUs, adsl2LineStatusSigAttenDs, adsl2LineStatusSigAttenUs, adsl2LineStatusSnrMarginDs, adsl2LineStatusSnrMarginUs, adsl2LineStatusAttainableRateDs, adsl2LineStatusAttainableRateUs, adsl2LineStatusActPsdDs, adsl2LineStatusActPsdUs, adsl2LineStatusActAtpDs,
ADSL2线性组对象-组对象{ADSL2LINECNFGMETABLE、ADSL2LINECNFGMETABLE、ADSL2LINECMDConfPMSF、ADSL2LINECMDConfLDSF、ADSL2LINECMDConfFailReason、ADSL2LINECMDADAutoModeColdStart、ADSL2LINEStatusATUTRANSYS、adsl2LineStatusPwrMngState、adsl2LineStatusInitResult、ADSL2LINEStatusLastStatus、ADSL2LINEStatusLastStatus、adsl2LineStatusAtuc、adsl2LineStatusInAttents、ADSL2LineStatusInAttentus、ADSL2LineStatusInAttents、ADSL2LineStatusInAttentus、ADSL2LineStatusnRmargins、ADSL2LineStatusnRmarginus、ADSL2LineStatusAcreatableRates、ADSL2LineStatusAcreatableRates、ADSL2LineStatusActpSDS、ADSL2LineStatusActpSDU、adsl2LineStatusActAtpDs、，
adsl2LineStatusActAtpUs
}
STATUS current
DESCRIPTION
"The group of configuration, status, and commands objects
on the line level."
::= { adsl2Groups 1 }
adsl2LineStatusActAtpUs
}
STATUS current
DESCRIPTION
"The group of configuration, status, and commands objects
on the line level."
::= { adsl2Groups 1 }
adsl2ChannelStatusGroup OBJECT-GROUP
OBJECTS
{
adsl2ChStatusChannelNum,
adsl2ChStatusActDataRate,
adsl2ChStatusPrevDataRate,
adsl2ChStatusActDelay
}
STATUS current
DESCRIPTION
"The group of status objects on the channel level."
::= { adsl2Groups 2 }
adsl2ChannelStatusGroup OBJECT-GROUP
OBJECTS
{
adsl2ChStatusChannelNum,
adsl2ChStatusActDataRate,
adsl2ChStatusPrevDataRate,
adsl2ChStatusActDelay
}
STATUS current
DESCRIPTION
"The group of status objects on the channel level."
::= { adsl2Groups 2 }
adsl2ChannelStatusAtmGroup OBJECT-GROUP
OBJECTS
{
adsl2ChStatusAtmStatus
}
STATUS current
DESCRIPTION
"The group of status objects on the data path level
when it is ATM."
::= { adsl2Groups 3 }
adsl2ChannelStatusAtmGroup OBJECT-GROUP
OBJECTS
{
adsl2ChStatusAtmStatus
}
STATUS current
DESCRIPTION
"The group of status objects on the data path level
when it is ATM."
::= { adsl2Groups 3 }
adsl2ChannelStatusPtmGroup OBJECT-GROUP
OBJECTS
{
adsl2ChStatusPtmStatus
}
STATUS current
DESCRIPTION
"The group of status objects on the data path level
when it is PTM."
::= { adsl2Groups 4 }
adsl2ChannelStatusPtmGroup OBJECT-GROUP
OBJECTS
{
adsl2ChStatusPtmStatus
}
STATUS current
DESCRIPTION
"The group of status objects on the data path level
when it is PTM."
::= { adsl2Groups 4 }
adsl2SCStatusGroup OBJECT-GROUP OBJECTS { adsl2SCStatusMtime, adsl2SCStatusSnr,
adsl2SCStatusGroup对象组对象{ADSL2SCStatusTime，adsl2SCStatusSnr，
adsl2SCStatusBitsAlloc,
adsl2SCStatusGainAlloc,
adsl2SCStatusTssi,
adsl2SCStatusLinScale,
adsl2SCStatusLinReal,
adsl2SCStatusLinImg,
adsl2SCStatusLogMt,
adsl2SCStatusLog,
adsl2SCStatusQlnMt,
adsl2SCStatusQln,
adsl2SCStatusLnAtten,
adsl2SCStatusSigAtten,
adsl2SCStatusSnrMargin,
adsl2SCStatusAttainableRate,
adsl2SCStatusActAtp,
adsl2SCStatusRowStatus
}
STATUS current
DESCRIPTION
"The group of status objects on the sub-carrier level.
They are updated as a result of a DELT process."
::= { adsl2Groups 5 }
adsl2SCStatusBitsAlloc,
adsl2SCStatusGainAlloc,
adsl2SCStatusTssi,
adsl2SCStatusLinScale,
adsl2SCStatusLinReal,
adsl2SCStatusLinImg,
adsl2SCStatusLogMt,
adsl2SCStatusLog,
adsl2SCStatusQlnMt,
adsl2SCStatusQln,
adsl2SCStatusLnAtten,
adsl2SCStatusSigAtten,
adsl2SCStatusSnrMargin,
adsl2SCStatusAttainableRate,
adsl2SCStatusActAtp,
adsl2SCStatusRowStatus
}
STATUS current
DESCRIPTION
"The group of status objects on the sub-carrier level.
They are updated as a result of a DELT process."
::= { adsl2Groups 5 }
adsl2LineInventoryGroup OBJECT-GROUP
OBJECTS
{
adsl2LInvG994VendorId,
adsl2LInvSystemVendorId,
adsl2LInvVersionNumber,
adsl2LInvSerialNumber,
adsl2LInvSelfTestResult,
adsl2LInvTransmissionCapabilities
}
STATUS current
DESCRIPTION
"The group of inventory objects per XTU."
::= { adsl2Groups 6 }
adsl2LineInventoryGroup OBJECT-GROUP
OBJECTS
{
adsl2LInvG994VendorId,
adsl2LInvSystemVendorId,
adsl2LInvVersionNumber,
adsl2LInvSerialNumber,
adsl2LInvSelfTestResult,
adsl2LInvTransmissionCapabilities
}
STATUS current
DESCRIPTION
"The group of inventory objects per XTU."
::= { adsl2Groups 6 }
adsl2LineConfTemplateGroup OBJECT-GROUP OBJECTS { adsl2LConfTempLineProfile, adsl2LConfTempChan1ConfProfile, adsl2LConfTempChan1RaRatioDs, adsl2LConfTempChan1RaRatioUs, adsl2LConfTempChan2ConfProfile, adsl2LConfTempChan2RaRatioDs, adsl2LConfTempChan2RaRatioUs,
adsl2LineConfTemplateGroup对象组对象{ADSL2ConfTemplineProfile，ADSL2ConfTempChan1ConfProfile，ADSL2ConfTempChan1Aratiods，ADSL2ConfTempChan1Aratiods，ADSL2ConfTempChan2ConfProfile，ADSL2ConfTempChan2Aratiods，
adsl2LConfTempChan3ConfProfile,
adsl2LConfTempChan3RaRatioDs,
adsl2LConfTempChan3RaRatioUs,
adsl2LConfTempChan4ConfProfile,
adsl2LConfTempChan4RaRatioDs,
adsl2LConfTempChan4RaRatioUs,
adsl2LConfTempRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line configuration template."
::= { adsl2Groups 7 }
adsl2LConfTempChan3ConfProfile,
adsl2LConfTempChan3RaRatioDs,
adsl2LConfTempChan3RaRatioUs,
adsl2LConfTempChan4ConfProfile,
adsl2LConfTempChan4RaRatioDs,
adsl2LConfTempChan4RaRatioUs,
adsl2LConfTempRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line configuration template."
::= { adsl2Groups 7 }
adsl2LineConfProfGroup OBJECT-GROUP
OBJECTS
{
adsl2LConfProfScMaskDs,
adsl2LConfProfScMaskUs,
adsl2LConfProfRfiBandsDs,
adsl2LConfProfRaModeDs,
adsl2LConfProfRaModeUs,
adsl2LConfProfTargetSnrmDs,
adsl2LConfProfTargetSnrmUs,
adsl2LConfProfMaxSnrmDs,
adsl2LConfProfMaxSnrmUs,
adsl2LConfProfMinSnrmDs,
adsl2LConfProfMinSnrmUs,
adsl2LConfProfAtuTransSysEna,
adsl2LConfProfPmMode,
adsl2LConfProfL0Time,
adsl2LConfProfL2Time,
adsl2LConfProfL2Atpr,
adsl2LConfProfL2Atprt,
adsl2LConfProfRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line configuration profile."
::= { adsl2Groups 8 }
adsl2LineConfProfGroup OBJECT-GROUP
OBJECTS
{
adsl2LConfProfScMaskDs,
adsl2LConfProfScMaskUs,
adsl2LConfProfRfiBandsDs,
adsl2LConfProfRaModeDs,
adsl2LConfProfRaModeUs,
adsl2LConfProfTargetSnrmDs,
adsl2LConfProfTargetSnrmUs,
adsl2LConfProfMaxSnrmDs,
adsl2LConfProfMaxSnrmUs,
adsl2LConfProfMinSnrmDs,
adsl2LConfProfMinSnrmUs,
adsl2LConfProfAtuTransSysEna,
adsl2LConfProfPmMode,
adsl2LConfProfL0Time,
adsl2LConfProfL2Time,
adsl2LConfProfL2Atpr,
adsl2LConfProfL2Atprt,
adsl2LConfProfRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line configuration profile."
::= { adsl2Groups 8 }
adsl2LineConfProfRaGroup OBJECT-GROUP OBJECTS { adsl2LConfProfRaUsNrmDs, adsl2LConfProfRaUsNrmUs, adsl2LConfProfRaUsTimeDs, adsl2LConfProfRaUsTimeUs, adsl2LConfProfRaDsNrmsDs,
ADSL2LConfProfraGroup对象组对象{adsl2LConfProfRaUsNrmDs，adsl2LConfProfRaUsNrmUs，adsl2LConfProfRaUsTimeDs，adsl2LConfProfRaUsTimeUs，ADSL2LConfProfradsnRmds，
adsl2LConfProfRaDsNrmsUs,
adsl2LConfProfRaDsTimeDs,
adsl2LConfProfRaDsTimeUs
}
STATUS current
DESCRIPTION
"The group of objects required for controlling the rate-
adaptive behavior of the line."
::= { adsl2Groups 9 }
adsl2LConfProfRaDsNrmsUs,
adsl2LConfProfRaDsTimeDs,
adsl2LConfProfRaDsTimeUs
}
STATUS current
DESCRIPTION
"The group of objects required for controlling the rate-
adaptive behavior of the line."
::= { adsl2Groups 9 }
adsl2LineConfProfMsgMinGroup OBJECT-GROUP
OBJECTS
{
adsl2LConfProfMsgMinUs,
adsl2LConfProfMsgMinDs
}
STATUS current
DESCRIPTION
"The group of objects required for controlling the rate
reserved for Overhead traffic."
::= { adsl2Groups 10 }
adsl2LineConfProfMsgMinGroup OBJECT-GROUP
OBJECTS
{
adsl2LConfProfMsgMinUs,
adsl2LConfProfMsgMinDs
}
STATUS current
DESCRIPTION
"The group of objects required for controlling the rate
reserved for Overhead traffic."
::= { adsl2Groups 10 }
adsl2LineConfProfModeSpecGroup OBJECT-GROUP
OBJECTS
{
adsl2LConfProfMaxNomPsdDs,
adsl2LConfProfMaxNomPsdUs,
adsl2LConfProfMaxNomAtpDs,
adsl2LConfProfMaxNomAtpUs,
adsl2LConfProfMaxAggRxPwrUs,
adsl2LConfProfPsdMaskDs,
adsl2LConfProfPsdMaskUs,
adsl2LConfProfPsdMaskSelectUs,
adsl2LConfProfModeSpecRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line configuration profile
that have an instance for each operation mode allowed."
::= { adsl2Groups 11 }
adsl2LineConfProfModeSpecGroup OBJECT-GROUP
OBJECTS
{
adsl2LConfProfMaxNomPsdDs,
adsl2LConfProfMaxNomPsdUs,
adsl2LConfProfMaxNomAtpDs,
adsl2LConfProfMaxNomAtpUs,
adsl2LConfProfMaxAggRxPwrUs,
adsl2LConfProfPsdMaskDs,
adsl2LConfProfPsdMaskUs,
adsl2LConfProfPsdMaskSelectUs,
adsl2LConfProfModeSpecRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line configuration profile
that have an instance for each operation mode allowed."
::= { adsl2Groups 11 }
adsl2ChConfProfileGroup OBJECT-GROUP OBJECTS { adsl2ChConfProfMinDataRateDs, adsl2ChConfProfMinDataRateUs, adsl2ChConfProfMaxDataRateDs, adsl2ChConfProfMaxDataRateUs,
adsl2ChConfProfileGroup对象组对象{adsl2chconfprofmindatarates，adsl2chconfprofmindatarates，adsl2chconfprofmaxdatarates，adsl2chconfprofmaxdatarates，
adsl2ChConfProfMinDataRateLowPwrDs,
adsl2ChConfProfMaxDelayDs,
adsl2ChConfProfMaxDelayUs,
adsl2ChConfProfMinProtectionDs,
adsl2ChConfProfMinProtectionUs,
adsl2ChConfProfMaxBerDs,
adsl2ChConfProfMaxBerUs,
adsl2ChConfProfUsDataRateDs,
adsl2ChConfProfDsDataRateDs,
adsl2ChConfProfUsDataRateUs,
adsl2ChConfProfDsDataRateUs,
adsl2ChConfProfRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a channel configuration profile."
::= { adsl2Groups 12 }
adsl2ChConfProfMinDataRateLowPwrDs,
adsl2ChConfProfMaxDelayDs,
adsl2ChConfProfMaxDelayUs,
adsl2ChConfProfMinProtectionDs,
adsl2ChConfProfMinProtectionUs,
adsl2ChConfProfMaxBerDs,
adsl2ChConfProfMaxBerUs,
adsl2ChConfProfUsDataRateDs,
adsl2ChConfProfDsDataRateDs,
adsl2ChConfProfUsDataRateUs,
adsl2ChConfProfDsDataRateUs,
adsl2ChConfProfRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a channel configuration profile."
::= { adsl2Groups 12 }
adsl2ChConfProfileAtmGroup OBJECT-GROUP
OBJECTS
{
adsl2ChConfProfImaEnabled,
adsl2ChStatusAtmStatus
}
STATUS current
DESCRIPTION
"The group of configuration objects required when the data
path is ATM."
::= { adsl2Groups 13 }
adsl2ChConfProfileAtmGroup OBJECT-GROUP
OBJECTS
{
adsl2ChConfProfImaEnabled,
adsl2ChStatusAtmStatus
}
STATUS current
DESCRIPTION
"The group of configuration objects required when the data
path is ATM."
::= { adsl2Groups 13 }
adsl2ChConfProfileMinResGroup OBJECT-GROUP
OBJECTS
{
adsl2ChConfProfMinResDataRateDs,
adsl2ChConfProfMinResDataRateUs
}
STATUS current
DESCRIPTION
"The group of configuration objects required for the
reserved data rate."
::= { adsl2Groups 14 }
adsl2ChConfProfileMinResGroup OBJECT-GROUP
OBJECTS
{
adsl2ChConfProfMinResDataRateDs,
adsl2ChConfProfMinResDataRateUs
}
STATUS current
DESCRIPTION
"The group of configuration objects required for the
reserved data rate."
::= { adsl2Groups 14 }
adsl2LineAlarmConfTemplateGroup OBJECT-GROUP OBJECTS { adsl2LAlarmConfTempLineProfile, adsl2LAlarmConfTempChan1ConfProfile, adsl2LAlarmConfTempChan2ConfProfile,
adsl2LineAlarmConfTemplateGroup对象组对象{ADSL2AlarmConfTemplineProfile，ADSL2AlarmConfTempChan1ConfProfile，ADSL2AlarmConfTempChan2ConfProfile，
adsl2LAlarmConfTempChan3ConfProfile,
adsl2LAlarmConfTempChan4ConfProfile,
adsl2LAlarmConfTempRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line alarm
template."
::= { adsl2Groups 15 }
adsl2LAlarmConfTempChan3ConfProfile,
adsl2LAlarmConfTempChan4ConfProfile,
adsl2LAlarmConfTempRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line alarm
template."
::= { adsl2Groups 15 }
adsl2LineAlarmConfProfileGroup OBJECT-GROUP
OBJECTS
{
adsl2LineAlarmConfProfileAtucThresh15MinFecs,
adsl2LineAlarmConfProfileAtucThresh15MinEs,
adsl2LineAlarmConfProfileAtucThresh15MinSes,
adsl2LineAlarmConfProfileAtucThresh15MinLoss,
adsl2LineAlarmConfProfileAtucThresh15MinUas,
adsl2LineAlarmConfProfileAturThresh15MinFecs,
adsl2LineAlarmConfProfileAturThresh15MinEs,
adsl2LineAlarmConfProfileAturThresh15MinSes,
adsl2LineAlarmConfProfileAturThresh15MinLoss,
adsl2LineAlarmConfProfileAturThresh15MinUas,
adsl2LineAlarmConfProfileThresh15MinFailedFullInt,
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt,
adsl2LineAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line alarm profile."
::= { adsl2Groups 16 }
adsl2LineAlarmConfProfileGroup OBJECT-GROUP
OBJECTS
{
adsl2LineAlarmConfProfileAtucThresh15MinFecs,
adsl2LineAlarmConfProfileAtucThresh15MinEs,
adsl2LineAlarmConfProfileAtucThresh15MinSes,
adsl2LineAlarmConfProfileAtucThresh15MinLoss,
adsl2LineAlarmConfProfileAtucThresh15MinUas,
adsl2LineAlarmConfProfileAturThresh15MinFecs,
adsl2LineAlarmConfProfileAturThresh15MinEs,
adsl2LineAlarmConfProfileAturThresh15MinSes,
adsl2LineAlarmConfProfileAturThresh15MinLoss,
adsl2LineAlarmConfProfileAturThresh15MinUas,
adsl2LineAlarmConfProfileThresh15MinFailedFullInt,
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt,
adsl2LineAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line alarm profile."
::= { adsl2Groups 16 }
adsl2ChAlarmConfProfileGroup OBJECT-GROUP
OBJECTS
{
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations,
adsl2ChAlarmConfProfileAtucThresh15MinCorrected,
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations,
adsl2ChAlarmConfProfileAturThresh15MinCorrected,
adsl2ChAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a channel alarm profile."
::= { adsl2Groups 17 }
adsl2ChAlarmConfProfileGroup OBJECT-GROUP
OBJECTS
{
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations,
adsl2ChAlarmConfProfileAtucThresh15MinCorrected,
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations,
adsl2ChAlarmConfProfileAturThresh15MinCorrected,
adsl2ChAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a channel alarm profile."
::= { adsl2Groups 17 }
adsl2PMLineCurrGroup OBJECT-GROUP OBJECTS
adsl2PMLineCurrGroup对象组对象
{
adsl2PMLCurrValidIntervals,
adsl2PMLCurrInvalidIntervals,
adsl2PMLCurr15MTimeElapsed,
adsl2PMLCurr15MFecs,
adsl2PMLCurr15MEs,
adsl2PMLCurr15MSes,
adsl2PMLCurr15MLoss,
adsl2PMLCurr15MUas,
adsl2PMLCurr1DayValidIntervals,
adsl2PMLCurr1DayInvalidIntervals,
adsl2PMLCurr1DayTimeElapsed,
adsl2PMLCurr1DayFecs,
adsl2PMLCurr1DayEs,
adsl2PMLCurr1DaySes,
adsl2PMLCurr1DayLoss,
adsl2PMLCurr1DayUas
}
STATUS current
DESCRIPTION
"The group of objects that report the line-level
counters for current PM intervals."
::= { adsl2Groups 18 }
{
adsl2PMLCurrValidIntervals,
adsl2PMLCurrInvalidIntervals,
adsl2PMLCurr15MTimeElapsed,
adsl2PMLCurr15MFecs,
adsl2PMLCurr15MEs,
adsl2PMLCurr15MSes,
adsl2PMLCurr15MLoss,
adsl2PMLCurr15MUas,
adsl2PMLCurr1DayValidIntervals,
adsl2PMLCurr1DayInvalidIntervals,
adsl2PMLCurr1DayTimeElapsed,
adsl2PMLCurr1DayFecs,
adsl2PMLCurr1DayEs,
adsl2PMLCurr1DaySes,
adsl2PMLCurr1DayLoss,
adsl2PMLCurr1DayUas
}
STATUS current
DESCRIPTION
"The group of objects that report the line-level
counters for current PM intervals."
::= { adsl2Groups 18 }
adsl2PMLineCurrInitGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLCurrInit15MTimeElapsed,
adsl2PMLCurrInit15MFullInits,
adsl2PMLCurrInit15MFailedFullInits,
adsl2PMLCurrInit1DayTimeElapsed,
adsl2PMLCurrInit1DayFullInits,
adsl2PMLCurrInit1DayFailedFullInits
}
STATUS current
DESCRIPTION
"The group of objects that report the full
initialization counters for current PM intervals."
::= { adsl2Groups 19 }
adsl2PMLineCurrInitGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLCurrInit15MTimeElapsed,
adsl2PMLCurrInit15MFullInits,
adsl2PMLCurrInit15MFailedFullInits,
adsl2PMLCurrInit1DayTimeElapsed,
adsl2PMLCurrInit1DayFullInits,
adsl2PMLCurrInit1DayFailedFullInits
}
STATUS current
DESCRIPTION
"The group of objects that report the full
initialization counters for current PM intervals."
::= { adsl2Groups 19 }
adsl2PMLineCurrInitShortGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLCurrInit15MShortInits,
adsl2PMLCurrInit15MFailedShortInits,
adsl2PMLCurrInit1DayShortInits,
adsl2PMLCurrInit1DayFailedShortInits
}
adsl2PMLineCurrInitShortGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLCurrInit15MShortInits,
adsl2PMLCurrInit15MFailedShortInits,
adsl2PMLCurrInit1DayShortInits,
adsl2PMLCurrInit1DayFailedShortInits
}
STATUS current
DESCRIPTION
"The group of objects that report the short
initialization counters for current PM intervals."
::= { adsl2Groups 20 }
STATUS current
DESCRIPTION
"The group of objects that report the short
initialization counters for current PM intervals."
::= { adsl2Groups 20 }
adsl2PMLineHist15MinGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLHist15MMonitoredTime,
adsl2PMLHist15MFecs,
adsl2PMLHist15MEs,
adsl2PMLHist15MSes,
adsl2PMLHist15MLoss,
adsl2PMLHist15MUas,
adsl2PMLHist15MValidInterval
}
STATUS current
DESCRIPTION
"The group of line-level PM counters for the previous
15-minute interval."
::= { adsl2Groups 21 }
adsl2PMLineHist15MinGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLHist15MMonitoredTime,
adsl2PMLHist15MFecs,
adsl2PMLHist15MEs,
adsl2PMLHist15MSes,
adsl2PMLHist15MLoss,
adsl2PMLHist15MUas,
adsl2PMLHist15MValidInterval
}
STATUS current
DESCRIPTION
"The group of line-level PM counters for the previous
15-minute interval."
::= { adsl2Groups 21 }
adsl2PMLineHist1DayGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLHist1DMonitoredTime,
adsl2PMLHist1DFecs,
adsl2PMLHist1DEs,
adsl2PMLHist1DSes,
adsl2PMLHist1DLoss,
adsl2PMLHist1DUas,
adsl2PMLHist1DValidInterval
}
STATUS current
DESCRIPTION
"The group of line-level PM counters for the previous
24-hour interval."
::= { adsl2Groups 22 }
adsl2PMLineHist1DayGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLHist1DMonitoredTime,
adsl2PMLHist1DFecs,
adsl2PMLHist1DEs,
adsl2PMLHist1DSes,
adsl2PMLHist1DLoss,
adsl2PMLHist1DUas,
adsl2PMLHist1DValidInterval
}
STATUS current
DESCRIPTION
"The group of line-level PM counters for the previous
24-hour interval."
::= { adsl2Groups 22 }
adsl2PMLineInitHist15MinGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLHistInit15MMonitoredTime,
adsl2PMLHistInit15MFullInits,
adsl2PMLHistInit15MFailedFullInits,
adsl2PMLHistInit15MValidInterval
}
adsl2PMLineInitHist15MinGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLHistInit15MMonitoredTime,
adsl2PMLHistInit15MFullInits,
adsl2PMLHistInit15MFailedFullInits,
adsl2PMLHistInit15MValidInterval
}
STATUS current
DESCRIPTION
"The group of PM counters for the previous 15-minute
interval's full initializations."
::= { adsl2Groups 23 }
STATUS current
DESCRIPTION
"The group of PM counters for the previous 15-minute
interval's full initializations."
::= { adsl2Groups 23 }
adsl2PMLineInitHist15MinShortGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLHistInit15MShortInits,
adsl2PMLHistInit15MFailedShortInits
}
STATUS current
DESCRIPTION
"The group of PM counters for the previous 15-minute
interval's short initializations."
::= { adsl2Groups 24 }
adsl2PMLineInitHist15MinShortGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLHistInit15MShortInits,
adsl2PMLHistInit15MFailedShortInits
}
STATUS current
DESCRIPTION
"The group of PM counters for the previous 15-minute
interval's short initializations."
::= { adsl2Groups 24 }
adsl2PMLineInitHist1DayGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLHistinit1DMonitoredTime,
adsl2PMLHistinit1DFullInits,
adsl2PMLHistinit1DFailedFullInits,
adsl2PMLHistinit1DValidInterval
}
STATUS current
DESCRIPTION
"The group of PM counters for the previous 24-hour
interval's full initializations."
::= { adsl2Groups 25 }
adsl2PMLineInitHist1DayGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLHistinit1DMonitoredTime,
adsl2PMLHistinit1DFullInits,
adsl2PMLHistinit1DFailedFullInits,
adsl2PMLHistinit1DValidInterval
}
STATUS current
DESCRIPTION
"The group of PM counters for the previous 24-hour
interval's full initializations."
::= { adsl2Groups 25 }
adsl2PMLineInitHist1DayShortGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLHistinit1DShortInits,
adsl2PMLHistinit1DFailedShortInits
}
STATUS current
DESCRIPTION
"The group of PM counters for the previous 24-hour
interval's short initializations."
::= { adsl2Groups 26 }
adsl2PMLineInitHist1DayShortGroup OBJECT-GROUP
OBJECTS
{
adsl2PMLHistinit1DShortInits,
adsl2PMLHistinit1DFailedShortInits
}
STATUS current
DESCRIPTION
"The group of PM counters for the previous 24-hour
interval's short initializations."
::= { adsl2Groups 26 }
adsl2PMChCurrGroup OBJECT-GROUP OBJECTS { adsl2PMChCurrValidIntervals,
adsl2PMChCurrGroup对象组对象{adsl2PMChCurrValidIntervals，
adsl2PMChCurrInvalidIntervals,
adsl2PMChCurr15MTimeElapsed,
adsl2PMChCurr15MCodingViolations,
adsl2PMChCurr15MCorrectedBlocks,
adsl2PMChCurr1DayValidIntervals,
adsl2PMChCurr1DayInvalidIntervals,
adsl2PMChCurr1DayTimeElapsed,
adsl2PMChCurr1DayCodingViolations,
adsl2PMChCurr1DayCorrectedBlocks
}
STATUS current
DESCRIPTION
"The group of objects that report the channel-level
counters for current PM intervals."
::= { adsl2Groups 27 }
adsl2PMChCurrInvalidIntervals,
adsl2PMChCurr15MTimeElapsed,
adsl2PMChCurr15MCodingViolations,
adsl2PMChCurr15MCorrectedBlocks,
adsl2PMChCurr1DayValidIntervals,
adsl2PMChCurr1DayInvalidIntervals,
adsl2PMChCurr1DayTimeElapsed,
adsl2PMChCurr1DayCodingViolations,
adsl2PMChCurr1DayCorrectedBlocks
}
STATUS current
DESCRIPTION
"The group of objects that report the channel-level
counters for current PM intervals."
::= { adsl2Groups 27 }
adsl2PMChHist15MinGroup OBJECT-GROUP
OBJECTS
{
adsl2PMChHist15MMonitoredTime,
adsl2PMChHist15MCodingViolations,
adsl2PMChHist15MCorrectedBlocks,
adsl2PMChHist15MValidInterval
}
STATUS current
DESCRIPTION
"The group of objects that report the channel-level
counters for previous 15-minute PM intervals."
::= { adsl2Groups 28 }
adsl2PMChHist15MinGroup OBJECT-GROUP
OBJECTS
{
adsl2PMChHist15MMonitoredTime,
adsl2PMChHist15MCodingViolations,
adsl2PMChHist15MCorrectedBlocks,
adsl2PMChHist15MValidInterval
}
STATUS current
DESCRIPTION
"The group of objects that report the channel-level
counters for previous 15-minute PM intervals."
::= { adsl2Groups 28 }
adsl2PMChHist1DGroup OBJECT-GROUP
OBJECTS
{
adsl2PMChHist1DMonitoredTime,
adsl2PMChHist1DCodingViolations,
adsl2PMChHist1DCorrectedBlocks,
adsl2PMChHist1DValidInterval
}
STATUS current
DESCRIPTION
"The group of objects that report the channel-level
counters for previous 24-hour PM intervals."
::= { adsl2Groups 29 }
adsl2PMChHist1DGroup OBJECT-GROUP
OBJECTS
{
adsl2PMChHist1DMonitoredTime,
adsl2PMChHist1DCodingViolations,
adsl2PMChHist1DCorrectedBlocks,
adsl2PMChHist1DValidInterval
}
STATUS current
DESCRIPTION
"The group of objects that report the channel-level
counters for previous 24-hour PM intervals."
::= { adsl2Groups 29 }
adsl2ScalarSCGroup OBJECT-GROUP OBJECTS { adsl2ScalarSCMaxInterfaces,
adsl2ScalarSCGroup对象组对象{adsl2ScalarSCMaxInterfaces，
adsl2ScalarSCAvailInterfaces
}
STATUS current
DESCRIPTION
"The group of objects that report the available memory
resources for DELT processes."
::= { adsl2Groups 30 }
adsl2ScalarSCAvailInterfaces
}
STATUS current
DESCRIPTION
"The group of objects that report the available memory
resources for DELT processes."
::= { adsl2Groups 30 }
adsl2ThreshNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS
{
adsl2LinePerfFECSThreshAtuc,
adsl2LinePerfFECSThreshAtur,
adsl2LinePerfESThreshAtuc,
adsl2LinePerfESThreshAtur,
adsl2LinePerfSESThreshAtuc,
adsl2LinePerfSESThreshAtur,
adsl2LinePerfLOSSThreshAtuc,
adsl2LinePerfLOSSThreshAtur,
adsl2LinePerfUASThreshAtuc,
adsl2LinePerfUASThreshAtur,
adsl2LinePerfCodingViolationsThreshAtuc,
adsl2LinePerfCodingViolationsThreshAtur,
adsl2LinePerfCorrectedThreshAtuc,
adsl2LinePerfCorrectedThreshAtur,
adsl2LinePerfFailedFullInitThresh,
adsl2LinePerfFailedShortInitThresh
}
STATUS current
DESCRIPTION
"This group supports notifications of significant conditions
associated with ADSL/ADSL2/ADSL2+ lines."
::= { adsl2Groups 31 }
adsl2ThreshNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS
{
adsl2LinePerfFECSThreshAtuc,
adsl2LinePerfFECSThreshAtur,
adsl2LinePerfESThreshAtuc,
adsl2LinePerfESThreshAtur,
adsl2LinePerfSESThreshAtuc,
adsl2LinePerfSESThreshAtur,
adsl2LinePerfLOSSThreshAtuc,
adsl2LinePerfLOSSThreshAtur,
adsl2LinePerfUASThreshAtuc,
adsl2LinePerfUASThreshAtur,
adsl2LinePerfCodingViolationsThreshAtuc,
adsl2LinePerfCodingViolationsThreshAtur,
adsl2LinePerfCorrectedThreshAtuc,
adsl2LinePerfCorrectedThreshAtur,
adsl2LinePerfFailedFullInitThresh,
adsl2LinePerfFailedShortInitThresh
}
STATUS current
DESCRIPTION
"This group supports notifications of significant conditions
associated with ADSL/ADSL2/ADSL2+ lines."
::= { adsl2Groups 31 }
adsl2StatusChangeNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS
{
adsl2LineStatusChangeAtuc,
adsl2LineStatusChangeAtur
}
STATUS current
DESCRIPTION
"This group supports notifications of threshold crossing
associated with ADSL/ADSL2/ADSL2+ lines."
::= { adsl2Groups 32 }
adsl2StatusChangeNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS
{
adsl2LineStatusChangeAtuc,
adsl2LineStatusChangeAtur
}
STATUS current
DESCRIPTION
"This group supports notifications of threshold crossing
associated with ADSL/ADSL2/ADSL2+ lines."
::= { adsl2Groups 32 }
END
终止
A management application intended to manage ADSL links (e.g., G.992.1) with this MIB module must be modified to adapt itself to certain differences between RFC 2662 [RFC2662] and this MIB module, including the following aspects:
使用此MIB模块管理ADSL链路（例如，g.992.1）的管理应用程序必须进行修改，以适应RFC 2662[RFC2662]和此MIB模块之间的某些差异，包括以下方面：
o Although the configuration templates/profiles allow referring to 1-4 bearer channels, ADSL links are limited to 2 channels at most.
o 尽管配置模板/配置文件允许参考1-4个承载信道，但ADSL链路最多限于2个信道。
o Although the channel configuration profile allows higher data rates, ADSL links are limited to downstream/upstream data rates as assumed in RFC 2662 [RFC2662].
o 尽管信道配置文件允许更高的数据速率，但ADSL链路仅限于RFC 2662[RFC2662]中假设的下游/上游数据速率。
o The Impulse Noise Protection (INP) configuration parameters are given by minimum protection and maximum delay parameters.
o 脉冲噪声保护（INP）配置参数由最小保护和最大延迟参数给出。
o The line configuration profile includes a sub-table that addresses mode-specific parameters. For ADSL links, the management application SHOULD create a row in that table for the 'adsl' mode.
o 线路配置配置文件包括一个子表，用于处理特定于模式的参数。对于ADSL链路，管理应用程序应在该表中为“ADSL”模式创建一行。
o The line configuration profile includes parameters that are irrelevant for ADSL links. Similarly, many status parameters in the MIB are irrelevant for certain ADSL modes. Therefore, it is advised to consult with ITU G.997.1 standard [G.997.1] regarding the scope and relevance of each parameter in this MIB.
o 线路配置配置文件包括与ADSL链路无关的参数。类似地，MIB中的许多状态参数与某些ADSL模式无关。因此，建议咨询ITU G.997.1标准[G.997.1]，了解本MIB中每个参数的范围和相关性。
There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability:
此MIB模块中定义了许多管理对象，其MAX-ACCESS子句为read-write和/或read-create。在某些网络环境中，此类对象可能被视为敏感或易受攻击。在没有适当保护的非安全环境中支持SET操作可能会对网络操作产生负面影响。以下是表和对象及其敏感度/漏洞：
o adsl2LineTable
o adsl2LineTable
The table consists of the following objects that support SET operations:
该表由以下支持集合操作的对象组成：
* adsl2LineCnfgTemplate * adsl2LineAlarmCnfgTemplate * adsl2LineCmndConfPmsf * adsl2LineCmndConfLdsf * adsl2LineCmndAutomodeColdStart
* ADSL2线路CNFGTemplate*ADSL2线路报警CNFGTemplate*ADSL2线路CmndConfPmsf*ADSL2线路CmndConfDsf*ADSL2线路CmndConfDsf*ADSL2线路CmndAutoModeColdStart
Unauthorized changes to adsl2LineCnfgTemplate could have a major adverse operational effect on many lines simultaneously.
对adsl2LineCnfgTemplate的未经授权的更改可能同时对多条线路产生重大不利的运营影响。
Unauthorized changes to adsl2LineAlarmCnfgTemplate could have a contrary effect on notifications.
对adsl2LineAlarmCnfgTemplate未经授权的更改可能会对通知产生相反的影响。
Unauthorized changes to adsl2LineCmndConfPmsf could have an adverse affect on the power consumption of a line and may disrupt an operational service.
未经授权对adsl2LineCmndConfPmsf进行更改可能会对线路的功耗产生不利影响，并可能中断运营服务。
Unauthorized changes to adsl2LineCmndConfLdsf could cause an unscheduled line test to be carried out on the line.
未经授权对adsl2LineCmndConfLdsf进行更改可能会导致在线路上执行非计划线路测试。
Unauthorized changes to adsl2LineCmndAutomodeColdStart could cause an unscheduled cold reset to the line.
未经授权对ADSL2LINECMDAUTOMODECOLDSTART进行更改可能会导致线路意外冷复位。
o adsl2SCStatusTable
o ADSL2SCStatus表
This table contains one object, adsl2SCStatusRowStatus, that supports SET operations. Unauthorized changes could result in line test results being deleted prematurely.
此表包含一个支持SET操作的对象adsl2SCStatusRowStatus。未经授权的更改可能导致过早删除测线结果。
o adsl2LineConfTemplateTable
o adsl2LineConfTemplateTable
The table consists of the following objects that support SET operations:
该表由以下支持集合操作的对象组成：
* adsl2LConfTempLineProfile * adsl2LConfTempChan1ConfProfile * adsl2LConfTempChan1RaRatioDs * adsl2LConfTempChan1RaRatioUs * adsl2LConfTempChan2ConfProfile * adsl2LConfTempChan2RaRatioDs * adsl2LConfTempChan2RaRatioUs * adsl2LConfTempChan3ConfProfile * adsl2LConfTempChan3RaRatioDs * adsl2LConfTempChan3RaRatioUs * adsl2LConfTempChan4ConfProfile * adsl2LConfTempChan4RaRatioDs * adsl2LConfTempChan4RaRatioUs * adsl2LConfTempRowStatus
* ADSL2ConfTemplineProfile*ADSL2ConfTempChan1ConfProfile*ADSL2ConfTempChan1Aratiods*ADSL2ConfTempChan1Aratiods*ADSL2ConfTempChan2ConfProfile*ADSL2ConfTempChan2Aratiods*ADSL2ConfTempChan2Aratiods*ADSL2ConfTempChan3Aratiods*ADSL2ConfTempChan3Aratious*ADSL2ConfTempChan4ConfProfile*ADSL2ConfTempChan4Raratiods*ADSL2ConfTempChan4Raratious*ADSL2ConfTempRowStatus
Unauthorized changes to adsl2LConfTempLineProfile, adsl2LConfTempChan1ConfProfile, adsl2LConfTempChan2ConfProfile, adsl2LConfTempChan3ConfProfile, or adsl2LConfTempChan4ConfProfile could have an adverse operational effect on several lines; could
未经授权更改ADSL2ConfTemplineProfile、ADSL2ConfTempChan1 ConfProfile、ADSL2ConfTempChan2 ConfProfile、ADSL2ConfTempChan3 ConfProfile或ADSL2ConfTempChan4 ConfProfile可能对多条线路产生不利的运营影响；能够
change several lines over to running in unwanted levels of operation; or could result in several services undergoing changes in the number of channels that carry the service.
将几条线路改为在不需要的运行水平下运行；或者可能导致多个服务在承载该服务的频道数量上发生变化。
Unauthorized changes to adsl2LConfTempChan1RaRatioDs, adsl2LConfTempChan2RaRatioDs, adsl2LConfTempChan3RaRatioDs, or adsl2LConfTempChan4RaRatioDs, would alter the relative rate allocations among all channels belonging to a line. This could have an adverse operational effect on several lines.
未经授权更改ADSL2ConfTempChan1Ratiods、ADSL2ConfTempChan2Ratiods、ADSL2ConfTempChan3Ratiods或ADSL2ConfTempChan4Ratiods将改变属于一条线路的所有信道之间的相对速率分配。这可能会对多条线路产生不利的运行影响。
Unauthorized changes to adsl2LConfTempRowStatus could result in templates being created or brought into service prematurely; or could result in templates being inadvertently deleted or taken out of service.
未经授权更改adsl2LConfTempRowStatus可能导致模板被创建或过早投入使用；或者可能导致模板被无意中删除或停止使用。
o adsl2LineConfProfTable
o adsl2LineConfProfTable
The table consists of the following objects that support SET operations:
该表由以下支持集合操作的对象组成：
* adsl2LConfProfScMaskDs * adsl2LConfProfScMaskUs * adsl2LConfProfRfiBandsDs * adsl2LConfProfRaModeDs * adsl2LConfProfRaModeUs * adsl2LConfProfRaUsNrmDs * adsl2LConfProfRaUsNrmUs * adsl2LConfProfRaUsTimeDs * adsl2LConfProfRaUsTimeUs * adsl2LConfProfRaDsNrmsDs * adsl2LConfProfRaDsNrmsUs * adsl2LConfProfRaDsTimeDs * adsl2LConfProfRaDsTimeUs * adsl2LConfProfTargetSnrmDs * adsl2LConfProfTargetSnrmUs * adsl2LConfProfMaxSnrmDs * adsl2LConfProfMaxSnrmUs * adsl2LConfProfMinSnrmDs * adsl2LConfProfMinSnrmUs * adsl2LConfProfMsgMinUs * adsl2LConfProfMsgMinDs * adsl2LConfProfAtuTransSysEna * adsl2LConfProfPmMode * adsl2LConfProfL0Time * adsl2LConfProfL2Time * adsl2LConfProfL2Atpr * adsl2LConfProfL2Atprt * adsl2LConfProfRowStatus
* adsl2confprofscmaskds*adsl2confprofscmaskus*adsl2confprofstribands*adsl2confproframds*adsl2confproframds*adsl2confprofrauds*adsl2confprofrauds*adsl2confprofrauds*adsl2confprofrauds*adsl2confprofrauds*adsl2confprofrauds*adsl2confprofrauds*adsl2confprofrauds*adsl2confprofrauds*adsl2confprofrauds*ADSL2ConfProfTargetSnrmds*ADSL2ConfProfTargetSnrmus*ADSL2ConfProfMaxSnrmds*ADSL2ConfProfMaxSnrmus*ADSL2ConfProfMinsRmds*ADSL2ConfProfMinsRmmus*ADSL2ConfProfProfMinus*ADSL2ConfProfProfMins*ADSL2ConfProfProfTranssysena*ADSL2ConfProfProfMode*ADSL2ConfProfProfL10时间*ADSL2ConfProfL2Time*ADSL2ConfProfL2TPR*ADSL2LConfProfL2ATPT*adsl2LConfProfRowStatus
Unauthorized changes resulting in the setting of any of the above objects to an incorrect value could have an adverse operational effect on several lines.
未经授权的更改导致将上述任何对象设置为不正确的值，可能会对多条线路产生不利的操作影响。
Also, unauthorized changes to adsl2LConfProfRowStatus could result in unwanted line profiles being created or brought into service prematurely; or could result in line profiles being inadvertently deleted or taken out of service.
此外，未经授权更改adsl2LConfProfRowStatus可能会导致创建不需要的线路配置文件或过早投入使用；或可能导致线路配置文件被无意中删除或停止使用。
o adsl2LineConfProfModeSpecTable
o adsl2LineConfProfModeSpecTable
The table consists of the following objects that support SET operations:
该表由以下支持集合操作的对象组成：
* adsl2LConfProfMaxNomPsdDs * adsl2LConfProfMaxNomPsdUs * adsl2LConfProfMaxNomAtpDs * adsl2LConfProfMaxNomAtpUs * adsl2LConfProfMaxAggRxPwrUs * adsl2LConfProfPsdMaskDs * adsl2LConfProfPsdMaskUs * adsl2LConfProfPsdMaskSelectUs * adsl2LConfProfModeSpecRowStatus
* adsl2LConfProfMaxNomPsdDs*adsl2LConfProfMaxNomPsdUs*ADSL2LConfProfMaxNomps*ADSL2LConfProfMaxNomps*adsl2LConfProfMaxAggRxPwrUs*ADSL2LConfProfProfPSDMASKU*adsl2LConfProfPsdMaskSelectUs*ADSL2LConfProfModesSpecRowStatus
Unauthorized changes resulting in the setting of any of the above objects to an incorrect value could have an adverse operational effect on several lines.
未经授权的更改导致将上述任何对象设置为不正确的值，可能会对多条线路产生不利的操作影响。
Also, unauthorized changes to adsl2LConfProfModeSpecRowStatus could result in unwanted PSD configurations being created or brought into service prematurely; or could result in PSD configurations being inadvertently deleted or taken out of service.
此外，未经授权更改adsl2LConfProfModeSpecRowStatus可能会导致创建不需要的PSD配置或过早投入使用；或可能导致屏蔽门配置被无意中删除或停止使用。
o adsl2ChConfProfileTable
o adsl2ChConfProfileTable
The table consists of the following objects that support SET operations:
该表由以下支持集合操作的对象组成：
* adsl2ChConfProfMinDataRateDs * adsl2ChConfProfMinDataRateUs * adsl2ChConfProfMinResDataRateDs * adsl2ChConfProfMinResDataRateUs * adsl2ChConfProfMaxDataRateDs * adsl2ChConfProfMaxDataRateUs * adsl2ChConfProfMinDataRateLowPwrDs * adsl2ChConfProfMaxDelayDs * adsl2ChConfProfMaxDelayUs
* adsl2chconfprofmindatarates*adsl2chconfprofmindatarates*adsl2chconfprofminresdatarates*adsl2chconfprofminresdatarates*adsl2chconfprofmaxdatarates*adsl2chconfprofmaxdatarates*adsl2chconfprofmindataratepowrds*adsl2ChConfProfMaxDelayDs*adsl2ChConfProfMaxDelayUs
* adsl2ChConfProfMinProtectionDs * adsl2ChConfProfMinProtectionUs * adsl2ChConfProfMaxBerDs * adsl2ChConfProfMaxBerUs * adsl2ChConfProfUsDataRateDs * adsl2ChConfProfDsDataRateDs * adsl2ChConfProfUsDataRateUs * adsl2ChConfProfDsDataRateUs * adsl2ChConfProfImaEnabled * adsl2ChConfProfRowStatus
* ADSL2HCONFPROFMINProtectionDS*ADSL2HCONFPROFMINProtectionUS*ADSL2HCONFPROFMAXBERDS*ADSL2HCONFPROFMAXBERUS*ADSL2HCONFPROFMODatarates*ADSL2HCONFPROFDSDatarates*ADSL2HCONFPROFDSDatarates*ADSL2HCONFPROFIMA启用*ADSL2HCONFPROFROWSTATUS
Unauthorized changes resulting in the setting of any of the above objects to an incorrect value could have an adverse operational effect on several lines.
未经授权的更改导致将上述任何对象设置为不正确的值，可能会对多条线路产生不利的操作影响。
Also, unauthorized changes to adsl2ChConfProfRowStatus could result in unwanted channel profiles being created or brought into service prematurely; or could result in channel profiles being inadvertently deleted or taken out of service.
此外，对adsl2ChConfProfRowStatus的未经授权的更改可能会导致不必要的信道配置文件被创建或过早投入使用；或者可能导致频道配置文件被无意中删除或停止服务。
o adsl2LineAlarmConfTemplateTable
o adsl2LineAlarmConfTemplateTable
The table consists of the following objects that support SET operations:
该表由以下支持集合操作的对象组成：
* adsl2LAlarmConfTempLineProfile * adsl2LAlarmConfTempChan1ConfProfile * adsl2LalarmConfTempChan2ConfProfile * adsl2LalarmConfTempChan3ConfProfile * adsl2LalarmConfTempChan4ConfProfile * adsl2LAlarmConfTempRowStatus
* ADSL2AlarmConfTemplineProfile*ADSL2AlarmConfTempChan1ConfProfile*ADSL2AlarmConfTempChan2ConfProfile*ADSL2AlarmConfTempChan3ConfProfile*ADSL2AlarmConfTempChan4ConfProfile*ADSL2AlarmConfTempRowStatus
Unauthorized changes to adsl2LAlarmConfTempLineProfile, adsl2LAlarmConfTempChan1ConfProfile, adsl2LAlarmConfTempChan2ConfProfile, adsl2LAlarmConfTempChan3ConfProfile, or adsl2LAlarmConfTempChan4ConfProfile could have an adverse effect on the management of notifications generated at the scope of several to many lines; or could change several to many lines over to running with unwanted management rates for generated notifications.
对ADSL2AlarmConfTemplineProfile、ADSL2AlarmConfTempChan1ConfProfile、ADSL2AlarmConfTempChan2ConfProfile、ADSL2AlarmConfTempChan3ConfProfile或ADSL2AlarmConfTempChan4ConfProfile的未经授权更改可能会对多行到多行范围内生成的通知的管理产生不利影响；或者可以将多行更改为以不需要的管理速率运行生成的通知。
Unauthorized changes to adsl2LAlarmConfTempRowStatus could result in alarm templates being created or brought into service prematurely; or could result in alarm templates being inadvertently deleted or taken out of service.
未经授权对ADSL2AlarmConfTemprowStatus进行更改可能会导致过早创建或使用报警模板；或可能导致无意中删除或停止使用报警模板。
o adsl2LineAlarmConfProfileTable
o adsl2LineAlarmConfProfileTable
The table consists of the following objects that support SET operations:
该表由以下支持集合操作的对象组成：
* adsl2LineAlarmConfProfileAtucThresh15MinFecs * adsl2LineAlarmConfProfileAtucThresh15MinEs * adsl2LineAlarmConfProfileAtucThresh15MinSes * adsl2LineAlarmConfProfileAtucThresh15MinLoss * adsl2LineAlarmConfProfileAtucThresh15MinUas * adsl2LineAlarmConfProfileAturThresh15MinFecs * adsl2LineAlarmConfProfileAturThresh15MinEs * adsl2LineAlarmConfProfileAturThresh15MinSes * adsl2LineAlarmConfProfileAturThresh15MinLoss * adsl2LineAlarmConfProfileAturThresh15MinUas * adsl2LineAlarmConfProfileThresh15MinFailedFullInt * adsl2LineAlarmConfProfileThresh15MinFailedShrtInt * adsl2LineAlarmConfProfileRowStatus
* ADSL2LineAlarmConfProfile Ucthresh15感染*ADSL2LineAlarmConfProfile Ucthresh15感染*ADSL2LineAlarmConfProfile Ucthresh15感染*ADSL2LineAlarmConfProfile Ucthresh15感染*ADSL2LineAlarmConfProfile Ucthresh15分钟*ADSL2LineAlarmConfProfile阈值15感染*ADSL2LineAlarmConfProfile阈值15感染*ADSL2LineAlarmConfProfile阈值15mInses*ADSL2LineAlarmConfProfile阈值15minLoss*ADSL2LineAlarmConfProfile阈值15min*ADSL2LineAlarmConfProfile阈值15minPailedFullint*ADSL2LineAlarmConfProfile阈值15minPailedShrTint*ADSL2LineAlarmConfProfile RowStatus
Increasing any of the threshold values could result in a notification being suppressed or deferred. Setting a threshold to 0 could result in a notification being suppressed. Suppressing or deferring a notification could prevent the timely delivery of important diagnostic information. Decreasing any of the threshold values could result in a notification being sent from the network falsely reporting a threshold crossing.
增加任何阈值都可能导致通知被抑制或延迟。将阈值设置为0可能会导致通知被抑制。禁止或推迟通知可能会妨碍重要诊断信息的及时传递。降低任何阈值都可能导致从网络发送的通知错误地报告阈值交叉。
Changing a threshold value could also have an impact on the amount of notifications the agent sends. The Notifications Section of this document has a paragraph that provides general guidance on the rate-limiting of notifications. Agent implementations not providing rate-limiting could result in notifications being generated at an uncontrolled rate. Unauthorized changes to a threshold value could result in an undesired notification rate.
更改阈值也可能会影响代理发送的通知量。本文件的通知部分有一个段落，提供了关于通知率限制的一般指导。不提供速率限制的代理实现可能导致以不受控制的速率生成通知。未经授权更改阈值可能会导致意外的通知率。
Unauthorized changes to row status could result in unwanted line alarm profiles being created or brought into service. Also, changes to the row status could result in line alarm profiles being inadvertently deleted or taken out of service.
未经授权更改行状态可能会导致创建或使用不需要的行报警配置文件。此外，行状态的更改可能会导致线路报警配置文件被无意中删除或停止使用。
o adsl2ChAlarmConfProfileTable
o ADSL2CHALARM配置文件表
The table consists of the following objects that support SET operations:
该表由以下支持集合操作的对象组成：
* adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations * adsl2ChAlarmConfProfileAtucThresh15MinCorrected * adsl2ChAlarmConfProfileAturThresh15MinCodingViolations * adsl2ChAlarmConfProfileAturThresh15MinCorrected * adsl2ChAlarmConfProfileRowStatus * adsl2LineAlarmConfProfileAturThresh15MinFecs * adsl2LineAlarmConfProfileAturThresh15MinEs * adsl2LineAlarmConfProfileAturThresh15MinSes * adsl2LineAlarmConfProfileAturThresh15MinLoss * adsl2LineAlarmConfProfileAturThresh15MinUas * adsl2LineAlarmConfProfileThresh15MinFailedFullInt * adsl2LineAlarmConfProfileThresh15MinFailedShrtInt * adsl2LineAlarmConfProfileRowStatus
* ADSL2CHALARMCONFPROFILEATUCTRESH15MINCODING违规*ADSL2CHALARMCONFPROFILEATUCTRESH15MINCODING违规*ADSL2CHALARMCONFPROFILEATURTHESH15MINCODING违规*ADSL2CHALARMCONFPROFILEATURTHESH15MINCODING违规*ADSL2CHALARMCONFPROFILEATURATURTHESH15MINFICS*ADSL2LINEARMCONFPROFILEATURATURTHESH15MINC违规*ADSL2CHALARMCONFPROFILEATURATURATURTHESH15MINC违规*ADSL2 LINEADSL2LineAlarmConfProfile阈值15mInses*ADSL2LineAlarmConfProfile阈值15minLoss*ADSL2LineAlarmConfProfile阈值15min*ADSL2LineAlarmConfProfile阈值15minPailedFullint*ADSL2LineAlarmConfProfile阈值15minPailedShrTint*ADSL2LineAlarmConfProfile RowStatus
Increasing any of the threshold values could result in a notification being suppressed or deferred. Setting a threshold to 0 could result in a notification being suppressed. Suppressing or deferring a notification could prevent the timely delivery of important diagnostic information. Decreasing any of the threshold values could result in a notification being sent from the network falsely reporting a threshold crossing.
增加任何阈值都可能导致通知被抑制或延迟。将阈值设置为0可能会导致通知被抑制。禁止或推迟通知可能会妨碍重要诊断信息的及时传递。降低任何阈值都可能导致从网络发送的通知错误地报告阈值交叉。
Changing a threshold value could also have an impact on the amount of notifications the agent sends. The Notifications Section of this document has a paragraph that provides general guidance on the rate-limiting of notifications. Agent implementations not providing rate-limiting could result in notifications being generated at an uncontrolled rate. Unauthorized changes to a threshold value could result in an undesired notification rate.
更改阈值也可能会影响代理发送的通知量。本文件的通知部分有一个段落，提供了关于通知率限制的一般指导。不提供速率限制的代理实现可能导致以不受控制的速率生成通知。未经授权更改阈值可能会导致意外的通知率。
Unauthorized changes to row status could result in unwanted channel alarm profiles being created or brought into service. Also, changes to the row status could result in channel alarm profiles being inadvertently deleted or taken out of service.
对行状态的未经授权更改可能会导致创建或投入使用不需要的通道报警配置文件。此外，对行状态的更改可能会导致通道报警配置文件被无意中删除或停止使用。
Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability:
在某些网络环境中，此MIB模块中的某些可读对象（即具有MAX-ACCESS而非not ACCESS的对象）可能被视为敏感或易受攻击。因此，在通过SNMP通过网络发送这些对象时，控制甚至获取和/或通知对这些对象的访问，甚至可能加密这些对象的值，这一点非常重要。以下是表和对象及其敏感度/漏洞：
o adsl2LineInventoryTable
o adsl2LineInventoryTable
Access to these objects would allow an intruder to obtain information about which vendor's equipment is in use on the network. Further, such information is considered sensitive in many environments for competitive reasons.
对这些对象的访问将允许入侵者获取有关网络上使用的供应商设备的信息。此外，由于竞争原因，此类信息在许多环境中被视为敏感信息。
* adsl2LInvG994VendorId * adsl2LInvSystemVendorId * adsl2LInvVersionNumber * adsl2LInvSerialNumber * adsl2LInvSelfTestResult * adsl2LInvTransmissionCapabilities
* ADSL2LINVG994供应商ID*adsl2LInvSystemVendorId*adsl2LInvVersionNumber*adsl2LInvSerialNumber*adsl2LInvSelfTestResult*adsl2LInvTransmissionCapabilities
SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPSec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module.
SNMPv3之前的SNMP版本未包含足够的安全性。即使网络本身是安全的（例如通过使用IPSec），即使如此，也无法控制安全网络上的谁可以访问和获取/设置（读取/更改/创建/删除）此MIB模块中的对象。
It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], Section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy).
建议实施者考虑SNMPv3框架所提供的安全特性（参见[RCFC310]，第8节），包括对SNMPv3加密机制的完全支持（用于身份验证和隐私）。
It is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access only to those objects whose principals (users) have legitimate rights to indeed GET or SET (change/create/delete) them.
建议部署SNMPv3并启用加密安全性。然后，客户/运营商有责任确保对访问此MIB模块实例的SNMP实体进行了正确配置，以仅对其主体（用户）拥有合法权限来获取或设置（更改/创建/删除）它们的对象进行访问。
The authors are deeply grateful to the authors of the HDSL2 LINE MIB (RFC 4319), Clay Sikes and Bob Ray, for contributing to accelerating the work on this document. The structure of this document as well as several paragraphs originate in their document.
作者非常感谢HDSL2生产线MIB（RFC 4319）的作者Clay Sikes和Bob Ray，感谢他们为加速本文档的工作所做的贡献。本文件的结构以及几个段落源自其文件。
Special thanks to Bert Wijnen for his meticulous review of this text.
特别感谢Bert Wijnen对本文的仔细审阅。
Other contributions and advice were received from the following:
从以下方面收到了其他捐款和咨询意见：
Bert Wijnen (Lucent) Bob Ray (Pesa) Chen Jian (Huawei) Clay Sikes (Zhone) Mauro Molinari (Marconi) Narendranath Nair (Wipro) Randy Presuhn (Mindspring) Veena Naidu (Wipro)
伯特·维伊南（朗讯）鲍勃·雷（佩萨）陈健（华为）克莱·赛克斯（Zhone）毛罗·莫利纳里（马可尼）纳伦德拉纳特·奈尔（维普罗）兰迪·普雷森（明斯普林）维娜·奈杜（维普罗）
[G.992.1] "Asymmetric digital subscriber line (ADSL) transceivers", ITU-T G.992.1, 1999.
[G.992.1]“非对称数字用户线（ADSL）收发器”，ITU-T G.992.11999。
[G.992.2] "Splitterless asymmetric digital subscriber line (ADSL) transceivers", ITU-T G.992.2, 1999.
[G.992.2]“无分路器非对称数字用户线（ADSL）收发器”，ITU-T G.992.21999。
[G.992.3] "Asymmetric digital subscriber line transceivers 2 (ADSL2)", ITU-T G.992.3, 2002.
[G.992.3]“非对称数字用户线路收发器2（ADSL2）”，ITU-T G.992.3，2002年。
[G.992.4] "Splitterless asymmetric digital subscriber line transceivers 2 (Splitterless ADSL2)", ITU-T G.992.4, 2002.
[G.992.4]“无分路器非对称数字用户线路收发器2（无分路器ADSL2）”，ITU-T G.992.42002。
[G.992.5] "Asymmetric digital subscriber line (ADSL) transceivers - Extended bandwidth ADSL2 (ADSL2+)", ITU-T G.992.5, 2003.
[G.992.5]“非对称数字用户线（ADSL）收发器-扩展带宽ADSL2（ADSL2+）”，ITU-T G.992.52003。
[G.993.2] "Very-high speed Digital Subscriber Line Transceivers 2 (VDSL2 draft)", ITU-T G.993.2, July 2005.
[G.993.2]“甚高速数字用户线收发器2（VDSL2草案）”，ITU-T G.993.2，2005年7月。
[G.997.1] "Physical layer management for digital subscriber line (DSL) transceivers", ITU-T G.997.1, May 2003.
[G.997.1]“数字用户线（DSL）收发器的物理层管理”，ITU-T G.997.11903年5月。
[G.997.1am1] "Physical layer management for digital subscriber line (DSL) transceivers Amendment 1", ITU-T G.997.1 Amendment 1, December 2003.
[G.997.1am1]“数字用户线（DSL）收发器的物理层管理修正案1”，ITU-T G.997.1修正案1，2003年12月。
[G.997.1am2] "Physical layer management for digital subscriber line (DSL) transceivers Amendment 2", ITU-T G.997.1 Amendment 2, January 2005.
[G.997.1am2]“数字用户线（DSL）收发器的物理层管理修正案2”，ITU-T G.997.1修正案2，2005年1月。
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2119]Bradner，S.，“RFC中用于表示需求水平的关键词”，BCP 14，RFC 2119，1997年3月。
[RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2578]McCloghrie，K.，Ed.，Perkins，D.，Ed.，和J.Schoenwaeld，Ed.“管理信息的结构版本2（SMIv2）”，STD 58，RFC 2578，1999年4月。
[RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999.
[RFC2579]McCloghrie，K.，Ed.，Perkins，D.，Ed.，和J.Schoenwaeld，Ed.“SMIv2的文本约定”，STD 58，RFC 2579，1999年4月。
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999.
[RFC2580]McCloghrie，K.，Perkins，D.，和J.Schoenwaeld，“SMIv2的一致性声明”，STD 58，RFC 25801999年4月。
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000.
[RFC2863]McCloghrie，K.和F.Kastenholz，“接口组MIB”，RFC 28632000年6月。
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks", STD 62, RFC 3411, December 2002.
[RFC3411]Harrington，D.，Presohn，R.，和B.Wijnen，“描述简单网络管理协议（SNMP）管理框架的体系结构”，STD 62，RFC 3411，2002年12月。
[RFC3593] Tesink, K., "Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals", RFC 3593, September 2003.
[RFC3593]Tesink，K.“使用基于15分钟间隔的性能历史记录的MIB模块的文本约定”，RFC 3593，2003年9月。
[RFC3705] Ray, B. and R. Abbi, "High Capacity Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals", RFC 3705, February 2004.
[RFC3705]Ray，B.和R.Abbi，“使用基于15分钟间隔的性能历史记录的MIB模块的高容量文本约定”，RFC 3705，2004年2月。
[T1E1.413] J. Bingham & F. Van der Putten, "Network and Customer Installation Interfaces - Asymmetric Digital Subscriber Line (ADSL) Metallic Interface. (T1.413 Issue 2)", ANSI T1E1.413-1998, June 1998.
[T1E1.413]J.Bingham&F.Van der Putten，“网络和客户安装接口-非对称数字用户线（ADSL）金属接口（T1.413第2期）”，ANSI T1E1.413-1998，1998年6月。
[TR-90] Abbi, R., "Protocol Independent Object Model for Managing Next Generation ADSL Technologies", DSL Forum TR-90, December 2004.
[TR-90]Abbi，R.，“管理下一代ADSL技术的协议无关对象模型”，DSL论坛TR-90，2004年12月。
[RFC2662] Bathrick, G. and F. Ly, "Definitions of Managed Objects for the ADSL Lines", RFC 2662, August 1999.
[RFC2662]Bathrick，G.和F.Ly，“ADSL线路管理对象的定义”，RFC 2662，1999年8月。
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, December 2002.
[RFC3410]Case，J.，Mundy，R.，Partain，D.，和B.Stewart，“互联网标准管理框架的介绍和适用性声明”，RFC 34102002年12月。
[RFC3418] Presuhn, R., "Management Information Base (MIB) for the Simple Network Management Protocol (SNMP)", STD 62, RFC 3418, December 2002.
[RFC3418]Presohn，R.，“简单网络管理协议（SNMP）的管理信息库（MIB）”，STD 62，RFC 3418，2002年12月。
Authors' Addresses
作者地址
Moti Morgenstern ECI Telecom Ltd. 30 Hasivim St. Petach Tikva 49517 Israel
Moti Morgenstern ECI电信有限公司30 Hasivim St.Petach Tikva 49517以色列
Phone: +972 3 926 6258
Fax: +972 3 928 7342
EMail: moti.Morgenstern@ecitele.com
Phone: +972 3 926 6258
Fax: +972 3 928 7342
EMail: moti.Morgenstern@ecitele.com
Menachem Dodge ECI Telecom Ltd. 30 Hasivim St. Petach Tikva 49517 Israel
以色列Hasivim St.Petach Tikva 30号Menahem Dodge ECI电信有限公司49517
Phone: +972 3 926 8421
Fax: +972 3 928 7342
EMail: mbdodge@ieee.org
Phone: +972 3 926 8421
Fax: +972 3 928 7342
EMail: mbdodge@ieee.org
Scott Baillie NEC Australia 649-655 Springvale Road Mulgrave, Victoria 3170 Australia
澳大利亚维多利亚州马尔格雷夫斯普林维尔路649-655号斯科特贝利NEC 3170
Phone: +61 3 9264 3986
Fax: +61 3 9264 3892
EMail: scott.baillie@nec.com.au
Phone: +61 3 9264 3986
Fax: +61 3 9264 3892
EMail: scott.baillie@nec.com.au
Umberto Bonollo NEC Australia 649-655 Springvale Road Mulgrave, Victoria 3170 Australia
澳大利亚维多利亚州马尔格雷夫斯普林维尔路649-655号，邮编：3170
Phone: +61 3 9264 3385
Fax: +61 3 9264 3892
EMail: umberto.bonollo@nec.com.au
Phone: +61 3 9264 3385
Fax: +61 3 9264 3892
EMail: umberto.bonollo@nec.com.au
Full Copyright Statement
完整版权声明
Copyright (C) The Internet Society (2006).
版权所有（C）互联网协会（2006年）。
This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights.
本文件受BCP 78中包含的权利、许可和限制的约束，除其中规定外，作者保留其所有权利。
This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
本文件及其包含的信息是按“原样”提供的，贡献者、他/她所代表或赞助的组织（如有）、互联网协会和互联网工程任务组不承担任何明示或暗示的担保，包括但不限于任何保证，即使用本文中的信息不会侵犯任何权利，或对适销性或特定用途适用性的任何默示保证。
Intellectual Property
知识产权
The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79.
IETF对可能声称与本文件所述技术的实施或使用有关的任何知识产权或其他权利的有效性或范围，或此类权利下的任何许可可能或可能不可用的程度，不采取任何立场；它也不表示它已作出任何独立努力来确定任何此类权利。有关RFC文件中权利的程序信息，请参见BCP 78和BCP 79。
Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr.
向IETF秘书处披露的知识产权副本和任何许可证保证，或本规范实施者或用户试图获得使用此类专有权利的一般许可证或许可的结果，可从IETF在线知识产权存储库获取，网址为http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org.
IETF邀请任何相关方提请其注意任何版权、专利或专利申请，或其他可能涵盖实施本标准所需技术的专有权利。请将信息发送至IETF的IETF-ipr@ietf.org.
Acknowledgement
确认
Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA).
RFC编辑器功能的资金由IETF行政支持活动（IASA）提供。