Network Working Group A. Ahmad
Request for Comments: 4547 Cisco Systems Inc.
Category: Standards Track G. Nakanishi
Motorola
June 2006
Network Working Group A. Ahmad
Request for Comments: 4547 Cisco Systems Inc.
Category: Standards Track G. Nakanishi
Motorola
June 2006
Event Notification Management Information Base for Data over Cable Service Interface Specifications (DOCSIS)-Compliant Cable Modems and Cable Modem Termination Systems
电缆数据服务接口规范（DOCSIS）兼容电缆调制解调器和电缆调制解调器终端系统的事件通知管理信息库
Status of This Memo
关于下段备忘
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
本文件规定了互联网社区的互联网标准跟踪协议，并要求进行讨论和提出改进建议。有关本协议的标准化状态和状态，请参考当前版本的“互联网官方协议标准”（STD 1）。本备忘录的分发不受限制。
Copyright Notice
版权公告
Copyright (C) The Internet Society (2006).
版权所有（C）互联网协会（2006年）。
Abstract
摘要
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it defines a basic set of managed objects for Simple Network Management Protocol (SNMP) based event notification management of Data Over Cable Service Interface Specification (DOCSIS) compliant Cable Modems and Cable Modem Termination Systems. This MIB is defined as an extension to the DOCSIS Cable Device MIB.
此备忘录定义了管理信息库（MIB）的一部分，用于Internet社区中的网络管理协议。在基于事件管理（SNMP）的网络调制解调器（SIS）规范中，定义了特定电缆终端的基本电缆管理（SIS）和基于事件管理的电缆管理（SIS）规范。此MIB定义为DOCSIS电缆设备MIB的扩展。
This memo specifies a MIB module in a manner that is compliant to the Structure of Management Information Version 2 (SMIv2). The set of objects is consistent with the SNMP framework and existing SNMP standards.
本备忘录以符合管理信息版本2（SMIv2）结构的方式指定MIB模块。对象集与SNMP框架和现有SNMP标准一致。
Table of Contents
目录
1. The Internet-Standard Management Framework ......................2
2. Glossary ........................................................2
2.1. BPI - Baseline Privacy Interface ...........................3
2.2. BPI - Baseline Privacy Plus Interface ......................3
2.3. CATV .......................................................3
2.4. CM - Cable Modem ...........................................3
2.5. CMTS - Cable Modem Termination System ......................3
2.6. DOCSIS .....................................................3
2.7. Downstream .................................................4
2.8. Head-end ...................................................4
2.9. MAC Packet .................................................4
2.10. RF ........................................................4
2.11. SID .......................................................4
2.12. TLV .......................................................4
2.13. Upstream ..................................................4
3. Overview ........................................................4
3.1. Structure of the MIB .......................................5
4. Definitions .....................................................5
5. Contributors ...................................................35
6. Acknowledgements ...............................................36
7. Security Considerations ........................................36
8. IANA Considerations ............................................37
9. References .....................................................37
9.1. Normative References ......................................37
9.2. Informative References ....................................38
1. The Internet-Standard Management Framework ......................2
2. Glossary ........................................................2
2.1. BPI - Baseline Privacy Interface ...........................3
2.2. BPI - Baseline Privacy Plus Interface ......................3
2.3. CATV .......................................................3
2.4. CM - Cable Modem ...........................................3
2.5. CMTS - Cable Modem Termination System ......................3
2.6. DOCSIS .....................................................3
2.7. Downstream .................................................4
2.8. Head-end ...................................................4
2.9. MAC Packet .................................................4
2.10. RF ........................................................4
2.11. SID .......................................................4
2.12. TLV .......................................................4
2.13. Upstream ..................................................4
3. Overview ........................................................4
3.1. Structure of the MIB .......................................5
4. Definitions .....................................................5
5. Contributors ...................................................35
6. Acknowledgements ...............................................36
7. Security Considerations ........................................36
8. IANA Considerations ............................................37
9. References .....................................................37
9.1. Normative References ......................................37
9.2. Informative References ....................................38
For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [16].
有关描述当前互联网标准管理框架的文件的详细概述，请参阅RFC 3410[16]第7节。
Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [2], STD 58, RFC 2579 [3] and STD 58, RFC 2580 [4].
托管对象通过虚拟信息存储（称为管理信息库或MIB）进行访问。MIB对象通常通过简单网络管理协议（SNMP）进行访问。MIB中的对象是使用管理信息结构（SMI）中定义的机制定义的。本备忘录规定了符合SMIv2的MIB模块，如STD 58、RFC 2578[2]、STD 58、RFC 2579[3]和STD 58、RFC 2580[4]所述。
The terms in this document are derived either from normal cable system usage, or from the documents associated with the Data Over Cable Service Interface Specification (DOCSIS) process.
本文件中的术语来源于正常电缆系统使用，或来源于与电缆数据服务接口规范（DOCSIS）流程相关的文件。
A mechanism for providing data privacy over the HFC network in DOCSIS 1.0 systems [8].
DOCSIS 1.0系统中通过HFC网络提供数据隐私的机制[8]。
A mechanism that extends the Baseline Privacy Interface with the addition of CM authentication over the HFC network in DOCSIS 1.1/2.0 systems and beyond [9].
通过在DOCSIS 1.1/2.0系统及更高版本的HFC网络上添加CM认证扩展基线隐私接口的机制[9]。
Originally "Community Antenna Television", now used to refer to any cable or hybrid fiber and cable system used to deliver video signals to a community.
最初是“社区天线电视”，现在用来指用于向社区传送视频信号的任何有线或混合光纤和有线系统。
A CM acts as a "slave" station in a DOCSIS-compliant cable data system.
CM充当DOCSIS兼容电缆数据系统中的“从”站。
A generic term covering a cable bridge or cable router in a head-end. A CMTS acts as the master station in a DOCSIS-compliant cable data system. It is the only station that transmits downstream, and it controls the scheduling of upstream transmissions by its associated CMs.
涵盖前端电缆桥架或电缆路由器的通用术语。CMTS充当DOCSIS兼容电缆数据系统中的主站。它是唯一一个下行传输的站点，并且它通过其相关的CMs控制上行传输的调度。
DOCSIS stands for "Data-over-Cable Service Interface Specifications" and refers to the ITU-T J.112 Annex B standard for cable modem systems [10], [13] commonly known as DOCSIS 1.0. The DOCSIS 1.1 specification is an extension of DOCSIS 1.0, with new features to support quality of service, fragmentation, and requirements for European cable plants [14].
DOCSIS代表“电缆数据服务接口规范”，并参考ITU-T J.112附录B电缆调制解调器系统标准[10]，[13]，通常称为DOCSIS 1.0。DOCSIS 1.1规范是DOCSIS 1.0的扩展，具有支持服务质量、分段和欧洲电缆厂要求的新功能[14]。
DOCSIS 2.0 [15] builds upon DOCSIS 1.1 and provides all of the features and functionality that DOCSIS 1.1 provides. In addition, it provides some significant enhancements in upstream capacity over DOCSIS 1.1, such as 30.72 Mbps maximum upstream channel capacity, Synchronous-Code Division Multiple Access (CDMA) operation, increased robustness to upstream noise and channel impairments, Enhanced Reed-Solomon error correction, and Trellis Coded Modulation.
DOCSIS 2.0[15]以DOCSIS 1.1为基础，提供DOCSIS 1.1提供的所有特性和功能。此外，与DOCSIS 1.1相比，它还显著增强了上行容量，例如30.72 Mbps最大上行信道容量、同步码分多址（CDMA）操作、增强了对上行噪声和信道损伤的鲁棒性、增强了Reed-Solomon纠错和网格编码调制。
The direction from the CMTS to the CM.
从CMT到CM的方向。
The origination point in most cable systems of the subscriber video signals. Generally also the location of the CMTS equipment.
在大多数有线电视系统中，用户视频信号的起始点。通常还包括CMTS设备的位置。
A term referring to DOCSIS Protocol Data Unit (PDU).
指DOCSIS协议数据单元（PDU）的术语。
A term referring to Radio Frequency.
指无线电频率的术语。
A term referring to DOCSIS Service ID. The SID identifies a particular upstream bandwidth allocation and class-of-service management for DOCSIS, and identifies a particular bidirectional security association for BPI.
指DOCSIS服务ID的术语。SID标识DOCSIS的特定上行带宽分配和服务管理类别，并标识BPI的特定双向安全关联。
TLV stands for Type/Length/Value. TLV is an encoding method consisting of three fields. The first field indicates the type of element, the second field indicates the length of the element, and the third field contains the element's value.
TLV代表类型/长度/值。TLV是一种由三个字段组成的编码方法。第一个字段表示元素的类型，第二个字段表示元素的长度，第三个字段包含元素的值。
The direction from the CM to the CMTS.
从CM到CMT的方向。
Offering High Speed Internet Service in the cable industry has become extremely successful. DOCSIS devices are being deployed at a rate of multiple thousands per day. Although operators are enjoying successful deployment, they are also facing the challenge of properly managing deployed devices. Operators are using Simple Network Management Protocol, a set of Management Information Base (MIB) required by DOCSIS, and SNMP Notifications to manage deployed DOCSIS devices. The usage of SNMP Notification for event reporting is becoming more popular as an effective and efficient method for network monitoring.
在有线电视行业提供高速互联网服务已经非常成功。DOCSIS设备正以每天数千台的速度部署。尽管运营商享受着成功部署的乐趣，但他们也面临着正确管理已部署设备的挑战。运营商正在使用简单网络管理协议、DOCSIS所需的一组管理信息库（MIB）和SNMP通知来管理部署的DOCSIS设备。将SNMP通知用于事件报告作为一种有效的网络监控方法正变得越来越流行。
Unfortunately, only a minimal set of SNMP Notifications is currently available. This notification MIB, in conjunction with [11] and [12], provides a minimum set of standard DOCSIS Notifications that DOCSIS devices SHOULD support to enable successful management of DOCSIS devices and networks.
不幸的是，目前只有一组最小的SNMP通知可用。此通知MIB与[11]和[12]一起提供了DOCSIS设备应支持的最低标准DOCSIS通知集，以实现对DOCSIS设备和网络的成功管理。
This document defines a set of objects required for the event notification management of DOCSIS-compliant Cable Modems (CMs) and Cable Modem Termination Systems (CMTSs). The MIB module is derived from the DOCSIS [11] and [12].
本文件定义了DOCSIS兼容电缆调制解调器（CMs）和电缆调制解调器终端系统（CMTSs）事件通知管理所需的一组对象。MIB模块源自DOCSIS[11]和[12]。
Appendix H of [11] defines all DOCSIS 1.1 required events, and Appendix D of [12] does that for DOCSIS 2.0. The notifications specified in this document are used to notify these events via SNMP.
[11]的附录H定义了所有DOCSIS 1.1要求的事件，[12]的附录D对DOCSIS 2.0进行了定义。本文档中指定的通知用于通过SNMP通知这些事件。
In this document, the key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" are to be interpreted as described in RFC 2119 [1].
本文件中的关键词“必须”、“不得”、“必需”、“应”、“不应”、“应”、“不应”、“建议”、“可”和“可选”应按照RFC 2119[1]中的说明进行解释。
This DOCS-IETF-CABLE-DEVICE-NOTIFICATION-MIB was designed to extend the RFC2669 [5] notification module.
此DOCS-IETF-CABLE-DEVICE-NOTIFICATION-MIB旨在扩展RFC2669[5]通知模块。
Two groups of SNMP notification objects are defined in this document. One group defines notifications for cable modem events, and the other group defines notifications for cable modem termination system events.
本文档中定义了两组SNMP通知对象。一个组定义电缆调制解调器事件的通知，另一个组定义电缆调制解调器终端系统事件的通知。
DOCSIS defines numerous events, and each event is assigned to a functional category. This MIB defines a notification object for each functional category. The varbinding list of each notification includes information about the event that occurred on the device.
DOCSIS定义了许多事件，每个事件都分配给一个功能类别。此MIB为每个功能类别定义一个通知对象。每个通知的varbinding列表都包含有关设备上发生的事件的信息。
The MIB module defined here IMPORTs from SNMPv2-SMI [2], SNMPv2-CONF [3], DOCS-CABLE-DEVICE-MIB [5], DOCS-IF-MIB [6], and IF-MIB [7].
此处定义的MIB模块从SNMPv2 SMI[2]、SNMPv2 CONF[3]、DOCS-CABLE-DEVICE-MIB[5]、DOCS-IF-MIB[6]和IF-MIB[7]导入。
DOCS-IETF-CABLE-DEVICE-NOTIFICATION-MIB DEFINITIONS ::= BEGIN
DOCS-IETF-CABLE-DEVICE-NOTIFICATION-MIB DEFINITIONS ::= BEGIN
IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2 FROM SNMPv2-SMI -- RFC 2578 MODULE-COMPLIANCE,
从SNMPv2 SMI导入模块标识、对象类型、通知类型、mib-2--RFC 2578模块符合性，
OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- RFC 2580
SNMPv2 CONF中的对象组、通知组--RFC2580
docsDevEvLevel, docsDevEvId, docsDevEvText, docsDevSwFilename, docsDevSwServer, docsDevServerDhcp, docsDevServerTime FROM DOCS-CABLE-DEVICE-MIB -- RFC 2669
docsDevEvLevel、docsDevEvId、docsDevEvText、docsDevSwFilename、docsDevSwServer、docsDevServerDhcp、docsDevServerTime FROM DOCS-CABLE-DEVICE-MIB--RFC 2669
docsIfCmCmtsAddress, docsIfCmtsCmStatusMacAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType, docsIfCmtsCmStatusDocsisRegMode, docsIfCmtsCmStatusModulationType FROM DOCS-IF-MIB -- RFC 4546
docsIfCmCmtsAddress、docsIfCmtsCmStatusMacAddress、DOCSIFCMSISSBaseCapability、DOCSIFCMStatusDocsiOperMode、docsIfCmtsCmStatusModulationType、DOCSIFCMTSCMStatusDocsiRegMode、docsIfCmtsCmStatusModulationType来自DOCS-IF-MIB--RFC 4546
ifPhysAddress FROM IF-MIB; -- RFC 2863
来自IF-MIB的ifPhysAddress；——RFC 2863
docsDevNotifMIB MODULE-IDENTITY
docsDevNotifMIB模块标识
LAST-UPDATED "200605240000Z" -- May 24, 2006 ORGANIZATION "IETF IP over Cable Data Network Working Group"
最近更新的“20060524000Z”-2006年5月24日组织“IETF IP over Cable数据网络工作组”
CONTACT-INFO " Azlina Ahmad Postal: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134, U.S.A. Phone: 408 853 7927 E-mail: azlina@cisco.com
联系信息“Azlina Ahmad邮政：思科系统公司，地址：美国加利福尼亚州圣何塞西塔斯曼大道170号，邮编：95134电话：408 853 7927电子邮件：azlina@cisco.com
Greg Nakanishi Postal: Motorola 6450 Sequence Drive San Diego, CA 92121, U.S.A. Phone: 858 404 2366 E-mail: gnakanishi@motorola.com
Greg Nakanishi邮政：美国加利福尼亚州圣地亚哥市摩托罗拉6450 Sequence Drive 92121电话：858 404 2366电子邮件：gnakanishi@motorola.com
IETF IPCDN Working Group General Discussion: ipcdn@ietf.org
IETF IPCDN工作组一般性讨论：ipcdn@ietf.org
Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn
Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn
Co-chairs: Richard Woundy,
richard_woundy@cable.comcast.com
Jean-Francois Mule, jf.mule@cablelabs.com"
Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn
Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn
Co-chairs: Richard Woundy,
richard_woundy@cable.comcast.com
Jean-Francois Mule, jf.mule@cablelabs.com"
DESCRIPTION "The Event Notification MIB is an extension of the CABLE DEVICE MIB. It defines various notification objects for both cable modem and cable modem termination systems. Two groups of SNMP notification objects are defined. One group is for notifying cable modem events, and one group is for notifying cable modem termination system events.
描述“事件通知MIB是电缆设备MIB的扩展。它为电缆调制解调器和电缆调制解调器终端系统定义了各种通知对象。定义了两组SNMP通知对象。一组用于通知电缆调制解调器事件，另一组用于通知电缆调制解调器终端系统事件。
DOCSIS defines numerous events, and each event is assigned to a functional category. This MIB defines a notification object for each functional category. The varbinding list of each notification includes information about the event that occurred on the device.
DOCSIS定义了许多事件，每个事件都分配给一个功能类别。此MIB为每个功能类别定义一个通知对象。每个通知的varbinding列表都包含有关设备上发生的事件的信息。
Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4547; see the RFC itself for full legal notices."
版权所有（C）互联网协会（2006年）。此版本的MIB模块是RFC 4547的一部分；有关完整的法律通知，请参见RFC本身。”
REVISION "200605240000Z" -- May 24, 2006
DESCRIPTION
"Initial version, published as RFC 4547."
::= { mib-2 132 }
REVISION "200605240000Z" -- May 24, 2006
DESCRIPTION
"Initial version, published as RFC 4547."
::= { mib-2 132 }
docsDevNotifControl OBJECT IDENTIFIER ::= { docsDevNotifMIB 1}
docsDevCmNotifs OBJECT IDENTIFIER ::= { docsDevNotifMIB 2 0 }
docsDevCmtsNotifs OBJECT IDENTIFIER ::= { docsDevNotifMIB 3 0 }
docsDevNotifControl OBJECT IDENTIFIER ::= { docsDevNotifMIB 1}
docsDevCmNotifs OBJECT IDENTIFIER ::= { docsDevNotifMIB 2 0 }
docsDevCmtsNotifs OBJECT IDENTIFIER ::= { docsDevNotifMIB 3 0 }
docsDevCmNotifControl OBJECT-TYPE SYNTAX BITS { cmInitTLVUnknownNotif( 0), cmDynServReqFailNotif( 1), cmDynServRspFailNotif( 2), cmDynServAckFailNotif( 3), cmBpiInitNotif( 4), cmBPKMNotif( 5), cmDynamicSANotif( 6), cmDHCPFailNotif( 7), cmSwUpgradeInitNotif( 8), cmSwUpgradeFailNotif( 9), cmSwUpgradeSuccessNotif( 10),
docsDevCmNotifControl对象类型语法位{CMINITTLVUNKNOWNOTIF（0）、cmDynServReqFailNotif（1）、cmDynServRspFailNotif（2）、cmDynServAckFailNotif（3）、CMBPINITNOTIF（4）、CMBPKNOTIF（5）、cmDynamicSANotif（6）、cmDHCPFailNotif（7）、cmSwUpgradeInitNotif（8）、cmSwUpgradeFailNotif（9）、cmSwUpgradeSuccessNotif（10），
cmSwUpgradeCVCNotif( 11), cmTODFailNotif( 12), cmDCCReqFailNotif( 13), cmDCCRspFailNotif( 14), cmDCCAckFailNotif( 15) } MAX-ACCESS read-write
cmSwUpgradeCVCNotif（11）、cmTODFailNotif（12）、CMDCREQUALINOTIF（13）、CMDCRSPFAILLNOTIF（14）、CMDCACKFAILNOTIF（15）}MAX-ACCESS读写
STATUS current DESCRIPTION "The object is used to enable specific CM notifications. For example, if the first bit is set, then docsDevCmInitTLVUnknownNotif is enabled. If it is not set, the notification is disabled. Note that notifications are also under the control of the MIB modules defined in RFC3413.
STATUS current DESCRIPTION“该对象用于启用特定的CM通知。例如，如果设置了第一位，则启用docsDevCmInitTLVUnknownNotif。如果未设置，则禁用通知。请注意，通知还受RFC3413中定义的MIB模块的控制。
If the device is rebooted,the value of this object SHOULD
revert to the default value.
"
DEFVAL { {} }
::= { docsDevNotifControl 1 }
If the device is rebooted,the value of this object SHOULD
revert to the default value.
"
DEFVAL { {} }
::= { docsDevNotifControl 1 }
docsDevCmtsNotifControl OBJECT-TYPE
SYNTAX BITS {
cmtsInitRegReqFailNotif( 0),
cmtsInitRegRspFailNotif( 1),
cmtsInitRegAckFailNotif( 2),
cmtsDynServReqFailNotif( 3),
cmtsDynServRspFailNotif( 4),
cmtsDynServAckFailNotif( 5),
cmtsBpiInitNotif( 6),
cmtsBPKMNotif( 7),
cmtsDynamicSANotif( 8),
cmtsDCCReqFailNotif( 9),
cmtsDCCRspFailNotif( 10),
cmtsDCCAckFailNotif( 11)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object is used to enable specific CMTS notifications.
For example, if the first bit is set, then
docsDevCmtsInitRegRspFailNotif is enabled. If it is not set,
the notification is disabled. Note that notifications are
also under the control of the MIB modules defined in
RFC3413.
docsDevCmtsNotifControl OBJECT-TYPE
SYNTAX BITS {
cmtsInitRegReqFailNotif( 0),
cmtsInitRegRspFailNotif( 1),
cmtsInitRegAckFailNotif( 2),
cmtsDynServReqFailNotif( 3),
cmtsDynServRspFailNotif( 4),
cmtsDynServAckFailNotif( 5),
cmtsBpiInitNotif( 6),
cmtsBPKMNotif( 7),
cmtsDynamicSANotif( 8),
cmtsDCCReqFailNotif( 9),
cmtsDCCRspFailNotif( 10),
cmtsDCCAckFailNotif( 11)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The object is used to enable specific CMTS notifications.
For example, if the first bit is set, then
docsDevCmtsInitRegRspFailNotif is enabled. If it is not set,
the notification is disabled. Note that notifications are
also under the control of the MIB modules defined in
RFC3413.
If the device is rebooted,the value of this object SHOULD
revert to the default value.
"
DEFVAL { {} }
::= { docsDevNotifControl 2 }
If the device is rebooted,the value of this object SHOULD
revert to the default value.
"
DEFVAL { {} }
::= { docsDevNotifControl 2 }
docsDevCmInitTLVUnknownNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"Notification to indicate that an unknown TLV was
encountered during the TLV parsing process.
docsDevCmInitTLVUnknownNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"Notification to indicate that an unknown TLV was
encountered during the TLV parsing process.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 1 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 1 }
docsDevCmDynServReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
docsDevCmDynServReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic service request during the dynamic services process.
“在动态服务过程中报告动态服务请求失败的通知。
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected to (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 2 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected to (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 2 }
docsDevCmDynServRspFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress,
docsDevCmDynServRspFailNotif通知类型对象{docsDevEvLevel、docsDevEvId、docsDevEvText、IFPHYSADRESS、，
docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION " A notification to report the failure of a dynamic service response during the dynamic services process.
docsIfCmCmtsAddress、docsIfDocsisBaseCapability、docsIfCmStatusDocsisOperMode、docsIfCmStatusModulationType}状态当前描述“在动态服务过程中报告动态服务响应失败的通知。
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 3}
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 3}
docsDevCmDynServAckFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
docsDevCmDynServAckFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic service acknowledgement during the dynamic services process.
“在动态服务过程中报告动态服务确认失败的通知。
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 4}
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 4}
docsDevCmBpiInitNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a BPI
initialization attempt during the registration process.
docsDevCmBpiInitNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a BPI
initialization attempt during the registration process.
This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the
此通知通过在其varbinding列表中包含以下对象来发送有关事件的附加信息。-docsDevEvLevel：与文件关联的优先级
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 5 }
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 5 }
docsDevCmBPKMNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a Baseline
Privacy Key Management (BPKM) operation.
docsDevCmBPKMNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a Baseline
Privacy Key Management (BPKM) operation.
This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS
此通知通过在其varbinding列表中包含以下对象来发送有关事件的附加信息。-docsDevEvLevel：与事件关联的优先级。-docsDevEvId:发生的事件的唯一标识符。-docsDevEvText：事件的文本描述。-ifPhysAddress：此电缆调制解调器电缆接口的MAC地址。-docsifcmtsaddress：CMT的MAC地址
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 6 }
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 6 }
docsDevCmDynamicSANotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic security
association operation.
docsDevCmDynamicSANotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic security
association operation.
This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting.
此通知通过在其varbinding列表中包含以下对象来发送有关事件的附加信息。-docsDevEvLevel：与事件关联的优先级。-docsDevEvId:发生的事件的唯一标识符。-docsDevEvText：事件的文本描述。-ifPhysAddress：此电缆调制解调器电缆接口的MAC地址。-DOCSIFCMTSAddress：CM连接到的CMT的MAC地址（如果CMT中有电缆卡/接口，则实际上是其连接到的电缆接口的MAC地址）。-docsIfDocsisBaseCapability：设备能够支持的DOCSIS规范（1.0、1.1、2.0）的最高版本。
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 7 }
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 7 }
docsDevCmDHCPFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsDevServerDhcp,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a DHCP operation.
docsDevCmDHCPFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsDevServerDhcp,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a DHCP operation.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsDevServerDhcp: the IP address of the DHCP server.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 8 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsDevServerDhcp: the IP address of the DHCP server.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 8 }
docsDevCmSwUpgradeInitNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsDevSwFilename,
docsDevSwServer,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to indicate that a software upgrade
has been initiated on the device.
docsDevCmSwUpgradeInitNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsDevSwFilename,
docsDevSwServer,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to indicate that a software upgrade
has been initiated on the device.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 9 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 9 }
docsDevCmSwUpgradeFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText,
DOCSDEVCMSWUPGRADEFILNOTIF通知类型对象{docsDevEvLevel、docsDevEvId、docsDevEvText、，
ifPhysAddress, docsIfCmCmtsAddress, docsDevSwFilename, docsDevSwServer, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a software upgrade attempt.
如果physaddress、docsIfCmCmtsAddress、docsDevSwFilename、docsDevSwServer、docsIfDocsisBaseCapability、docsIfCmStatusDocsisOperMode、docsIfCmStatusModulationType}STATUS current DESCRIPTION“报告软件升级尝试失败的通知。
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsDevSwFilename: the software image file name
- docsDevSwServer: the IP address of the server that
the image is retrieved from.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 10 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsDevSwFilename: the software image file name
- docsDevSwServer: the IP address of the server that
the image is retrieved from.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 10 }
docsDevCmSwUpgradeSuccessNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress,
DOCSDEVCMSWUPGRADESCESSNOTIF通知类型对象{docsDevEvLevel、docsDevEvId、docsDevEvText、ifPhysAddress、DOCSIFCMTSADDRESS、，
docsDevSwFilename, docsDevSwServer, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the software upgrade success status.
docsDevSwFilename、docsDevSwServer、docsIfDocsisBaseCapability、docsIfCmStatusDocsisOperMode、docsIfCmStatusModulationType}状态当前描述“报告软件升级成功状态的通知。
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsDevSwFilename: the software image file name
- docsDevSwServer: the IP address of the server that
the image is retrieved from.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 11 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsDevSwFilename: the software image file name
- docsDevSwServer: the IP address of the server that
the image is retrieved from.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 11 }
docsDevCmSwUpgradeCVCFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode,
docsDevCmSwUpgradeCVCFailNotif通知类型对象{docsDevEvLevel、docsDevEvId、docsDevEvText、IFPHYSADRESS、DOCSIFCMTSADDRESS、DOCSIFDOCSISBASEPability、docsIfCmStatusDocsisOperMode、，
docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report that the verification of the code file has failed during a secure software upgrade attempt.
docsIfCmStatusModulationType}STATUS current DESCRIPTION“报告在安全软件升级尝试期间代码文件验证失败的通知。
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 12 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 12 }
docsDevCmTODFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsDevServerTime,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a time of day
docsDevCmTODFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsDevServerTime,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a time of day
operation.
活动
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsDevServerTime: the IP address of the time server.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 13 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsDevServerTime: the IP address of the time server.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 13 }
docsDevCmDCCReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
" A notification to report the failure of a dynamic channel
change request during the dynamic channel change process
on the CM.
docsDevCmDCCReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
" A notification to report the failure of a dynamic channel
change request during the dynamic channel change process
on the CM.
This notification sends additional information about the event by including the following objects in its varbinding list.
此通知通过在其varbinding列表中包含以下对象来发送有关事件的附加信息。
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 14 }
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- ifPhysAddress: the MAC address of the cable
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 14 }
docsDevCmDCCRspFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change response during the dynamic channel
change process on the CM.
docsDevCmDCCRspFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change response during the dynamic channel
change process on the CM.
This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable
此通知通过在其varbinding列表中包含以下对象来发送有关事件的附加信息。-docsDevEvLevel：与事件关联的优先级。-docsDevEvId:发生的事件的唯一标识符。-docsDevEvText：事件的文本描述。-ifPhysAddress：电缆的MAC地址
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 15 }
interface of this cable modem.
- docsIfCmCmtsAddress: the MAC address of the CMTS
to which the CM is connected (if there is a cable
card/interface in the CMTS, then it is actually the
MAC address of the cable interface to which it is
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmStatusModulationType: the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 15 }
docsDevCmDCCAckFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change acknowledgement during the dynamic channel
change process on the CM.
docsDevCmDCCAckFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
ifPhysAddress,
docsIfCmCmtsAddress,
docsIfDocsisBaseCapability,
docsIfCmStatusDocsisOperMode,
docsIfCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change acknowledgement during the dynamic channel
change process on the CM.
This notification sends additional information about the event by including the following objects in its
此通知通过在其通知中包含以下对象来发送有关事件的附加信息
varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is
变量绑定列表docsDevEvLevel：与事件关联的优先级。-docsDevEvId:发生的事件的唯一标识符。-docsDevEvText：事件的文本描述。-ifPhysAddress：此电缆调制解调器电缆接口的MAC地址。-DOCSIFCMTSADDRESS：CM连接到的CMT的MAC地址（如果CMT中有电缆卡/接口，则它实际上是其连接到的电缆接口的MAC地址）
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmtsCmStatusModulationType the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 16}
connected).
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
that the CM is operating in.
- docsIfCmtsCmStatusModulationType the upstream modulation
methodology used by the CM.
"
::= { docsDevCmNotifs 16}
docsDevCmtsInitRegReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a registration
request from a CM during the CM initialization
process that was detected on the CMTS.
docsDevCmtsInitRegReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a registration
request from a CM during the CM initialization
process that was detected on the CMTS.
This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting.
此通知通过在其varbinding列表中包含以下对象来发送有关事件的附加信息。-docsDevEvLevel：与事件关联的优先级。-docsDevEvId:发生的事件的唯一标识符。-docsDevEvText：事件的文本描述。-docsIfCmtsCmStatusMacAddress：与此通知关联的CM的MAC地址。-ifPhysAddress:CMT的MAC地址（如果CMT中有电缆卡/接口，则实际上是连接到CM的电缆接口的MAC地址）连接到CM的电缆接口。-DOCSIFCMTSCMSTATUDSOCSISREGMODE：报告CM运行的QOS级别（1.0，1.1）。-docsIfDocsisBaseCapability：设备能够支持的DOCSIS规范（1.0、1.1、2.0）的最高版本。
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 1 }
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 1 }
docsDevCmtsInitRegRspFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a registration
response during the CM initialization
process that was detected by the CMTS.
docsDevCmtsInitRegRspFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a registration
response during the CM initialization
process that was detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 2 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 2 }
docsDevCmtsInitRegAckFailNotif NOTIFICATION-TYPE
docsDevCmtsInitRegAckFailNotif通知类型
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a registration
acknowledgement from the CM during the CM
initialization process that was detected by the CMTS.
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a registration
acknowledgement from the CM during the CM
initialization process that was detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 3 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 3 }
docsDevCmtsDynServReqFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress,
DOCSDEVCMTSDYNSERVERREQFAILNOTIF通知类型对象{docsDevEvLevel、docsDevEvId、docsDevEvText、docsIfCmtsCmStatusMacAddress、ifPhysAddress、，
docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic service request during the dynamic services process that was detected by the CMTS.
docsIfCmtsCmStatusDocsisRegMode、docsIfDocsisBaseCapability、docsIfCmtsCmStatusModulationType}状态当前描述“报告CMTS检测到的动态服务过程中动态服务请求失败的通知。
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 4 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 4 }
docsDevCmtsDynServRspFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
docsDevCmtsDynServRspFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic service response during the dynamic services process that was detected by the CMTS.
“报告CMT检测到的动态服务过程中动态服务响应失败的通知。
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 5 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 5 }
docsDevCmtsDynServAckFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic service
acknowledgement during the dynamic services
process that was detected by the CMTS.
docsDevCmtsDynServAckFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic service
acknowledgement during the dynamic services
process that was detected by the CMTS.
This notification sends additional information about the event by including the following objects in its
此通知通过在其通知中包含以下对象来发送有关事件的附加信息
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 6 }
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 6 }
docsDevCmtsBpiInitNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a BPI
initialization attempt during the CM registration process
that was detected by the CMTS.
docsDevCmtsBpiInitNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a BPI
initialization attempt during the CM registration process
that was detected by the CMTS.
This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred.
此通知通过在其varbinding列表中包含以下对象来发送有关事件的附加信息。-docsDevEvLevel：与事件关联的优先级。-docsDevEvId：发生的事件的唯一标识符。
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 7 }
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 7 }
docsDevCmtsBPKMNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a BPKM operation
that is detected by the CMTS.
docsDevCmtsBPKMNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a BPKM operation
that is detected by the CMTS.
This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface
此通知通过在其varbinding列表中包含以下对象来发送有关事件的附加信息。-docsDevEvLevel：与事件关联的优先级。-docsDevEvId:发生的事件的唯一标识符。-docsDevEvText：事件的文本描述。-docsIfCmtsCmStatusMacAddress：与此通知关联的CM的MAC地址。-ifPhysAddress:CMT电缆接口的MAC地址（如果CMT中有电缆卡/接口，则实际上是连接到CM的电缆接口的MAC地址）
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 8 }
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 8 }
docsDevCmtsDynamicSANotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic security
association operation that is detected by the CMTS.
docsDevCmtsDynamicSANotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic security
association operation that is detected by the CMTS.
This notification sends additional information about the event by including the following objects in its varbinding list.
此通知通过在其varbinding列表中包含以下对象来发送有关事件的附加信息。
- docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting.
- docsDevEvLevel：与事件关联的优先级。-docsDevEvId:发生的事件的唯一标识符。-docsDevEvText：事件的文本描述。-docsIfCmtsCmStatusMacAddress：与此通知关联的CM的MAC地址。-ifPhysAddress:CMT的MAC地址（如果CMT中有电缆卡/接口，则实际上是连接到CM的电缆接口的MAC地址）连接到CM的电缆接口。-DOCSIFCMTSCMSTATUDSOCSISREGMODE：报告CM运行的QOS级别（1.0，1.1）。-docsIfDocsisBaseCapability：设备能够支持的DOCSIS规范（1.0、1.1、2.0）的最高版本。
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 9 }
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 9 }
docsDevCmtsDCCReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change request during the dynamic channel
change process and is detected by the CMTS.
docsDevCmtsDCCReqFailNotif NOTIFICATION-TYPE
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change request during the dynamic channel
change process and is detected by the CMTS.
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 10 }
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 10 }
docsDevCmtsDCCRspFailNotif NOTIFICATION-TYPE
DOCSDEVCMTSDCCRPFAILNOTIF通知类型
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change response during the dynamic channel
change process and is detected by the CMTS.
OBJECTS {
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsIfCmtsCmStatusMacAddress,
ifPhysAddress,
docsIfCmtsCmStatusDocsisRegMode,
docsIfDocsisBaseCapability,
docsIfCmtsCmStatusModulationType
}
STATUS current
DESCRIPTION
"A notification to report the failure of a dynamic channel
change response during the dynamic channel
change process and is detected by the CMTS.
This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event.
此通知通过在其varbinding列表中包含以下对象来发送有关事件的附加信息。-docsDevEvLevel：与事件关联的优先级。-docsDevEvId:发生的事件的唯一标识符。-docsDevEvText：事件的文本描述。
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 11 }
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 11 }
docsDevCmtsDCCAckFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress,
docsDevCmtsDCCAckFailNotif通知类型对象{docsDevEvLevel，docsDevEvId，docsDevEvText，docsIfCmtsCmStatusMacAddress，
ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic channel change acknowledgement during the dynamic channel change process and is detected by the CMTS.
IFPHYSADRESS、DOCSIFCMTSCMSTATUDSOCSISREGMODE、DOCSIFDOCSISBASESCAPABILITY、DOCSIFCMTSCMSTATUSSMODULATIONTYPE}状态当前描述“在动态信道更改过程中报告动态信道更改确认失败的通知，由CMTS检测。
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 12}
This notification sends additional information about
the event by including the following objects in its
varbinding list.
- docsDevEvLevel: the priority level associated with the
event.
- docsDevEvId: the unique identifier of the event that
occurred.
- docsDevEvText: a textual description of the event.
- docsIfCmtsCmStatusMacAddress: the MAC address of the CM
with which this notification is associated.
- ifPhysAddress: the MAC address of the CMTS
(if there is a cable card/interface in the CMTS,
then it is actually the MAC address of the cable
interface that connected to the CM) cable interface
connected to the CM.
- docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
that the reporting CM is operating in.
- docsIfDocsisBaseCapability: the highest
version of the DOCSIS specification (1.0, 1.1, 2.0)
that the device is capable of supporting.
- docsIfCmtsCmStatusModulationType: the upstream
modulation methodology used by the CM.
"
::= { docsDevCmtsNotifs 12}
-- --Conformance definitions --
----一致性定义--
docsDevNotifConformance OBJECT IDENTIFIER
::= { docsDevNotifMIB 4 }
docsDevNotifGroups OBJECT IDENTIFIER
::= { docsDevNotifConformance 1 }
docsDevNotifCompliances OBJECT IDENTIFIER
::= { docsDevNotifConformance 2 }
docsDevCmNotifCompliance MODULE-COMPLIANCE
STATUS current
docsDevNotifConformance OBJECT IDENTIFIER
::= { docsDevNotifMIB 4 }
docsDevNotifGroups OBJECT IDENTIFIER
::= { docsDevNotifConformance 1 }
docsDevNotifCompliances OBJECT IDENTIFIER
::= { docsDevNotifConformance 2 }
docsDevCmNotifCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The compliance statement for CM Notifications and Control."
说明“构型管理通知和控制的合规性声明”
MODULE --docsDevNotif
MANDATORY-GROUPS {
docsDevCmNotifControlGroup,
docsDevCmNotificationGroup
}
::= { docsDevNotifCompliances 1 }
MODULE --docsDevNotif
MANDATORY-GROUPS {
docsDevCmNotifControlGroup,
docsDevCmNotificationGroup
}
::= { docsDevNotifCompliances 1 }
docsDevCmNotifControlGroup OBJECT-GROUP
OBJECTS {
docsDevCmNotifControl
}
STATUS current
DESCRIPTION
"This group represents objects that allow control
over CM Notifications."
::= { docsDevNotifGroups 1 }
docsDevCmNotifControlGroup OBJECT-GROUP
OBJECTS {
docsDevCmNotifControl
}
STATUS current
DESCRIPTION
"This group represents objects that allow control
over CM Notifications."
::= { docsDevNotifGroups 1 }
docsDevCmNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
docsDevCmInitTLVUnknownNotif,
docsDevCmDynServReqFailNotif,
docsDevCmDynServRspFailNotif,
docsDevCmDynServAckFailNotif,
docsDevCmBpiInitNotif,
docsDevCmBPKMNotif,
docsDevCmDynamicSANotif,
docsDevCmDHCPFailNotif,
docsDevCmSwUpgradeInitNotif,
docsDevCmSwUpgradeFailNotif,
docsDevCmSwUpgradeSuccessNotif,
docsDevCmSwUpgradeCVCFailNotif,
docsDevCmTODFailNotif,
docsDevCmDCCReqFailNotif,
docsDevCmDCCRspFailNotif,
docsDevCmDCCAckFailNotif
}
STATUS current
DESCRIPTION
"A collection of CM notifications providing device status
and control."
::= { docsDevNotifGroups 2 }
docsDevCmNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
docsDevCmInitTLVUnknownNotif,
docsDevCmDynServReqFailNotif,
docsDevCmDynServRspFailNotif,
docsDevCmDynServAckFailNotif,
docsDevCmBpiInitNotif,
docsDevCmBPKMNotif,
docsDevCmDynamicSANotif,
docsDevCmDHCPFailNotif,
docsDevCmSwUpgradeInitNotif,
docsDevCmSwUpgradeFailNotif,
docsDevCmSwUpgradeSuccessNotif,
docsDevCmSwUpgradeCVCFailNotif,
docsDevCmTODFailNotif,
docsDevCmDCCReqFailNotif,
docsDevCmDCCRspFailNotif,
docsDevCmDCCAckFailNotif
}
STATUS current
DESCRIPTION
"A collection of CM notifications providing device status
and control."
::= { docsDevNotifGroups 2 }
docsDevCmtsNotifCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION
DOCSDEVCMTSMNotifCompliance模块-合规状态当前说明
"The compliance statement for DOCSIS CMTS Notification
and Control."
MODULE --docsDevNotif
MANDATORY-GROUPS {
docsDevCmtsNotifControlGroup,
docsDevCmtsNotificationGroup
}
::= { docsDevNotifCompliances 2 }
"The compliance statement for DOCSIS CMTS Notification
and Control."
MODULE --docsDevNotif
MANDATORY-GROUPS {
docsDevCmtsNotifControlGroup,
docsDevCmtsNotificationGroup
}
::= { docsDevNotifCompliances 2 }
docsDevCmtsNotifControlGroup OBJECT-GROUP
OBJECTS {
docsDevCmtsNotifControl
}
STATUS current
DESCRIPTION
"This group represents objects that allow control
over CMTS Notifications."
::= { docsDevNotifGroups 3 }
docsDevCmtsNotifControlGroup OBJECT-GROUP
OBJECTS {
docsDevCmtsNotifControl
}
STATUS current
DESCRIPTION
"This group represents objects that allow control
over CMTS Notifications."
::= { docsDevNotifGroups 3 }
docsDevCmtsNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
docsDevCmtsInitRegReqFailNotif,
docsDevCmtsInitRegRspFailNotif,
docsDevCmtsInitRegAckFailNotif ,
docsDevCmtsDynServReqFailNotif,
docsDevCmtsDynServRspFailNotif,
docsDevCmtsDynServAckFailNotif,
docsDevCmtsBpiInitNotif,
docsDevCmtsBPKMNotif,
docsDevCmtsDynamicSANotif,
docsDevCmtsDCCReqFailNotif,
docsDevCmtsDCCRspFailNotif,
docsDevCmtsDCCAckFailNotif
}
STATUS current
DESCRIPTION
"A collection of CMTS notifications providing device
status and control."
::= { docsDevNotifGroups 4 }
docsDevCmtsNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
docsDevCmtsInitRegReqFailNotif,
docsDevCmtsInitRegRspFailNotif,
docsDevCmtsInitRegAckFailNotif ,
docsDevCmtsDynServReqFailNotif,
docsDevCmtsDynServRspFailNotif,
docsDevCmtsDynServAckFailNotif,
docsDevCmtsBpiInitNotif,
docsDevCmtsBPKMNotif,
docsDevCmtsDynamicSANotif,
docsDevCmtsDCCReqFailNotif,
docsDevCmtsDCCRspFailNotif,
docsDevCmtsDCCAckFailNotif
}
STATUS current
DESCRIPTION
"A collection of CMTS notifications providing device
status and control."
::= { docsDevNotifGroups 4 }
END
终止
Thanks go to the following people, who have made significant contributions to this document: Junming Gao, Jean-Francois Mule, Dave Raftus, Pak Siripunkaw, and Rich Woundy.
感谢以下对本文件做出重大贡献的人：高俊明、让·弗朗索瓦·穆尔、戴夫·拉弗特斯、帕克·西里蓬考和里奇·沃恩迪。
This document was produced by the IPCDN Working Group. Thanks to Harrie Hazewinkel and Bert Wijnen for their thorough review and insightful comments on this document. Special thanks to Rich Woundy, who made several valuable suggestions to improve the notifications.
本文件由IPCDN工作组编制。感谢Harrie Hazewinkel和Bert Wijnen对本文件的全面审查和深刻评论。特别感谢Rich Woundy，他为改进通知提出了一些有价值的建议。
There are two management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create (docsDevCmNotifControl and docsDevCmtsNotifControl). Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations.
此MIB模块中定义了两个管理对象，其MAX-ACCESS子句为读写和/或读创建（docsDevCmNotifControl和docsDevCmtsNotifControl）。在某些网络环境中，此类对象可能被视为敏感或易受攻击。在没有适当保护的非安全环境中支持SET操作可能会对网络操作产生负面影响。
Setting docsDevCmNotifControl or docsDevCmtsNotifControl may cause flooding of notifications, which can disrupt network service. Besides causing "flooding", changing the objects can also mean that notifications will not be emitted when one intends that to happen.
设置docsDevCmNotifControl或docsDevCmtsNotifControl可能会导致通知泛滥，从而中断网络服务。除了引起“泛洪”之外，更改对象还意味着在打算发生时不会发出通知。
This MIB defines a number of notification objects that send detailed information about the event that caused the generation of the notification. Information in the notification message includes: event priority, the event Id, the event message body, the CM DOCSIS capability, the CM DOCSIS QOS level, the CM DOCSIS upstream modulation type, the cable interface MAC address of the cable modem, and the cable card MAC address of the CMTS to which the modem is connected. The monitoring of these notification messages could be used to gather information about the state of the network and devices (CM and CMTS) attached to the network.
此MIB定义了许多通知对象，这些对象发送有关导致生成通知的事件的详细信息。通知消息中的信息包括：事件优先级、事件Id、事件消息正文、CM DOCSIS能力、CM DOCSIS QOS级别、CM DOCSIS上游调制类型、电缆调制解调器的电缆接口MAC地址以及调制解调器连接到的CMT的电缆卡MAC地址。对这些通知消息的监视可用于收集有关网络状态和连接到网络的设备（CM和CMT）的信息。
SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPSec), even then there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module.
SNMPv3之前的SNMP版本未包含足够的安全性。即使网络本身是安全的（例如通过使用IPSec），也无法控制安全网络上的谁可以访问和获取/设置（读取/更改/创建/删除）此MIB模块中的对象。
It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [16], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy).
建议实施者考虑SNMPv3框架提供的安全特性（见[ 16 ]，第8节），包括对SNMPv3加密机制的完全支持（用于身份验证和隐私）。
Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an
此外，不建议部署SNMPv3之前的SNMP版本。相反，建议部署SNMPv3并启用加密安全性。然后，客户/运营商有责任确保允许访问网络的SNMP实体
instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them.
此MIB模块的实例被正确配置为仅允许那些拥有合法权限来获取或设置（更改/创建/删除）对象的主体（用户）访问这些对象。
The MIB module defined in this document uses the following IANA-assigned OBJECT IDENTIFIER values recorded in the SMI Numbers registry:
本文档中定义的MIB模块使用SMI编号注册表中记录的以下IANA分配的对象标识符值：
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
docsDevNotifMIB { mib-2 132 }
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
docsDevNotifMIB { mib-2 132 }
[1] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.
[1] Bradner，S.，“RFC中用于表示需求水平的关键词”，BCP 14，RFC 2119，1997年3月。
[2] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[2] McCloghrie，K.，Perkins，D.，和J.Schoenwaeld，“管理信息的结构版本2（SMIv2）”，STD 58，RFC 2578，1999年4月。
[3] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999.
[3] McCloghrie，K.，Perkins，D.，和J.Schoenwaeld，“SMIv2的文本约定”，STD 58，RFC 2579，1999年4月。
[4] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999.
[4] McCloghrie，K.，Perkins，D.，和J.Schoenwaeld，“SMIv2的一致性声明”，STD 58，RFC 25801999年4月。
[5] St. Johns, M., "DOCSIS Cable Device MIB Cable Device Management Information Base for DOCSIS compliant Cable Modems and Cable Modem Termination Systems", RFC 2669, August 1999.
[5] St.Johns，M.，“符合DOCSIS标准的电缆调制解调器和电缆调制解调器终端系统的DOCSIS电缆设备MIB电缆设备管理信息库”，RFC 2669，1999年8月。
[6] Raftus, D. and E. Cardona, "Radio Frequency (RF) Interface Management Information Base for Data over Cable Service Interface Specifications (DOCSIS) 2.0 Compliant RF Interfaces", RFC 4546, June 2006.
[6] Raftus，D.和E.Cardona，“电缆数据服务接口规范（DOCSIS）2.0兼容射频接口的射频（RF）接口管理信息库”，RFC 45462006年6月。
[7] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000.
[7] McCloghrie，K.和F.Kastenholz，“接口组MIB”，RFC 28632000年6月。
[8] SCTE Data Standards Subcommittee, "Data-Over-Cable Service Interface Specifications: DOCSIS 1.0 Baseline Privacy Interface Specification SCTE 22-2", 2002, <http://www.scte.org/standards/>.
[8] SCTE数据标准小组委员会，“有线数据服务接口规范：DOCSIS 1.0基线隐私接口规范SCTE 22-2”，2002年<http://www.scte.org/standards/>.
[9] CableLabs, "Baseline Privacy Plus Interface Specification SP-BPI+040407", April 2004, <http://www.cablemodem.com/specifications/>.
[9] CableLabs，“基线隐私加接口规范SP-BPI+040407”，2004年4月<http://www.cablemodem.com/specifications/>.
[10] SCTE Data Standards Subcommittee, "Data-Over-Cable Service Interface Specifications: DOCSIS 1.0 Operations Support System Interface Specification Radio Frequency Interface SCTE 22-3", 2002, <http://www.scte.org/standards/>.
[10] SCTE数据标准小组委员会，“有线数据服务接口规范：DOCSIS 1.0操作支持系统接口规范射频接口SCTE 22-3”，2002年<http://www.scte.org/standards/>.
[11] CableLabs, "Data-Over-Cable Service Interface Specifications: Operations Support System Interface Specification CM-SP-OSSIv1.1-C01-050907", September 2005, <http://www.cablemodem.com/specifications/>.
[11] CableLabs，“有线数据服务接口规范：操作支持系统接口规范CM-SP-OSIV1.1-C01-050907”，2005年9月<http://www.cablemodem.com/specifications/>.
[12] CableLabs, "Data-Over-Cable Service Interface Specifications: Operations Support System Interface Specification CM-SP-OSSIv2.0-I09-050812", August 2005, <http://www.cablemodem.com/specifications/>.
[12] CableLabs，“有线数据服务接口规范：操作支持系统接口规范CM-SP-OSIV2.0-I09-050812”，2005年8月<http://www.cablemodem.com/specifications/>.
[13] SCTE Data Standards Subcommittee, "Data-Over-Cable Service Interface Specifications: DOCSIS 1.0 Radio Frequency Interface Specification SCTE 22-1", 2002, <http://www.scte.org/standards/>.
[13] SCTE数据标准小组委员会，“电缆数据服务接口规范：DOCSIS 1.0射频接口规范SCTE 22-1”，2002年<http://www.scte.org/standards/>.
[14] CableLabs, "Data-Over-Cable Service Interface Specifications: Radio Frequency Interface Specification CM-SP-RFIv1.1-C01- 050907", September 2005, <http://www.cablemodem.com/specifications/>.
[14] CableLabs，“电缆数据服务接口规范：射频接口规范CM-SP-RFIv1.1-C01-050907”，2005年9月<http://www.cablemodem.com/specifications/>.
[15] CableLabs, "Data-Over-Cable Service Interface Specifications: Radio Frequency Interface Specification CM-SP-RFIv2.0-I10- 051209", December 2005, <http://www.cablemodem.com/specifications/>.
[15] CableLabs，“电缆数据服务接口规范：射频接口规范CM-SP-RFIv2.0-I10-051209”，2005年12月<http://www.cablemodem.com/specifications/>.
[16] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, December 2002.
[16] Case，J.，Mundy，R.，Partain，D.，和B.Stewart，“互联网标准管理框架的介绍和适用性声明”，RFC 3410，2002年12月。
Authors' Addresses
作者地址
Azlina Ahmad Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134 US
美国加利福尼亚州圣何塞西塔斯曼大道170号Azlina Ahmad Cisco Systems，Inc.邮编：95134
Phone: 408 853 7927 EMail: azlina@cisco.com
电话：408 853 7927电子邮件：azlina@cisco.com
Greg Nakanishi Motorola 6450 Sequence Dr. San Diego, CA 92126 US
Greg Nakanishi摩托罗拉6450序列美国加利福尼亚州圣地亚哥92126博士
Phone: 858 404-2366 EMail: gnakanishi@motorola.com
电话：858 404-2366电子邮件：gnakanishi@motorola.com
Full Copyright Statement
完整版权声明
Copyright (C) The Internet Society (2006).
版权所有（C）互联网协会（2006年）。
This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights.
本文件受BCP 78中包含的权利、许可和限制的约束，除其中规定外，作者保留其所有权利。
This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
本文件及其包含的信息是按“原样”提供的，贡献者、他/她所代表或赞助的组织（如有）、互联网协会和互联网工程任务组不承担任何明示或暗示的担保，包括但不限于任何保证，即使用本文中的信息不会侵犯任何权利，或对适销性或特定用途适用性的任何默示保证。
Intellectual Property
知识产权
The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79.
IETF对可能声称与本文件所述技术的实施或使用有关的任何知识产权或其他权利的有效性或范围，或此类权利下的任何许可可能或可能不可用的程度，不采取任何立场；它也不表示它已作出任何独立努力来确定任何此类权利。有关RFC文件中权利的程序信息，请参见BCP 78和BCP 79。
Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr.
向IETF秘书处披露的知识产权副本和任何许可证保证，或本规范实施者或用户试图获得使用此类专有权利的一般许可证或许可的结果，可从IETF在线知识产权存储库获取，网址为http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org.
IETF邀请任何相关方提请其注意任何版权、专利或专利申请，或其他可能涵盖实施本标准所需技术的专有权利。请将信息发送至IETF的IETF-ipr@ietf.org.
Acknowledgement
确认
Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA).
RFC编辑器功能的资金由IETF行政支持活动（IASA）提供。