Network Working Group C. Sikes
Request for Comments: 4319 Zhone Technologies, Inc.
Obsoletes: 3276 B. Ray
Category: Standards Track PESA Switching Systems, Inc.
R. Abbi
Alcatel USA
December 2005
Network Working Group C. Sikes
Request for Comments: 4319 Zhone Technologies, Inc.
Obsoletes: 3276 B. Ray
Category: Standards Track PESA Switching Systems, Inc.
R. Abbi
Alcatel USA
December 2005
Definitions of Managed Objects for High Bit-Rate DSL - 2nd generation (HDSL2) and Single-Pair High-Speed Digital Subscriber Line (SHDSL) Lines
高比特率DSL-第二代（HDSL2）和单对高速数字用户线（SHDSL）线路的受管对象定义
Status of This Memo
关于下段备忘
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
本文件规定了互联网社区的互联网标准跟踪协议，并要求进行讨论和提出改进建议。有关本协议的标准化状态和状态，请参考当前版本的“互联网官方协议标准”（STD 1）。本备忘录的分发不受限制。
Copyright Notice
版权公告
Copyright (C) The Internet Society (2005).
版权所有（C）互联网协会（2005年）。
Abstract
摘要
This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community. In particular, it describes objects used for managing High Bit-Rate Digital Subscriber Line (DSL) - 2nd generation (HDSL2) and Single-Pair High-Speed Digital Subscriber Line (SHDSL) interfaces. This document introduces extensions to several objects and textual conventions defined in HDSL2-SHDSL-Line MIB (RFC 3276). This document obsoletes RFC 3276.
本文档定义了一个管理信息库（MIB）模块，用于Internet社区中的网络管理协议。特别地，它描述了用于管理高速数字用户线（DSL）-第二代（HDSL2）和单对高速数字用户线（SHDSL）接口的对象。本文档介绍对HDSL2 SHDSL Line MIB（RFC 3276）中定义的几个对象和文本约定的扩展。本文件淘汰了RFC 3276。
Table of Contents
目录
1. The Internet-Standard Management Framework ......................2
2. Overview ........................................................2
2.1. Relationship to Other MIBs .................................3
2.1.1. General IF-MIB Integration (RFC 2863) ...............3
2.1.2. Usage of ifTable ....................................3
2.2. IANA Considerations ........................................4
2.3. Conventions Used in the MIB Module .........................5
2.3.1. Naming Conventions ..................................5
2.3.2. Textual Conventions .................................5
2.4. Structure ..................................................7
2.5. Line Topology ..............................................9
2.6. Counters, Interval Buckets, and Thresholds ................10
2.7. Profiles ..................................................11
2.8. Notifications .............................................12
3. Definitions ....................................................14
4. Implementation Analysis ........................................66
5. Security Considerations ........................................66
6. Acknowledgements ...............................................71
7. References .....................................................72
7.1. Normative References ......................................72
7.2. Informative References ....................................73
1. The Internet-Standard Management Framework ......................2
2. Overview ........................................................2
2.1. Relationship to Other MIBs .................................3
2.1.1. General IF-MIB Integration (RFC 2863) ...............3
2.1.2. Usage of ifTable ....................................3
2.2. IANA Considerations ........................................4
2.3. Conventions Used in the MIB Module .........................5
2.3.1. Naming Conventions ..................................5
2.3.2. Textual Conventions .................................5
2.4. Structure ..................................................7
2.5. Line Topology ..............................................9
2.6. Counters, Interval Buckets, and Thresholds ................10
2.7. Profiles ..................................................11
2.8. Notifications .............................................12
3. Definitions ....................................................14
4. Implementation Analysis ........................................66
5. Security Considerations ........................................66
6. Acknowledgements ...............................................71
7. References .....................................................72
7.1. Normative References ......................................72
7.2. Informative References ....................................73
For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to Section 7 of RFC 3410 [RFC3410].
有关描述当前互联网标准管理框架的文件的详细概述，请参阅RFC 3410[RFC3410]第7节。
Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580].
托管对象通过虚拟信息存储（称为管理信息库或MIB）进行访问。MIB对象通常通过简单网络管理协议（SNMP）进行访问。MIB中的对象是使用管理信息结构（SMI）中定义的机制定义的。本备忘录规定了符合SMIv2的MIB模块，如STD 58、RFC 2578[RFC2578]、STD 58、RFC 2579[RFC2579]和STD 58、RFC 2580[RFC2580]所述。
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119].
本文件中的关键词“必须”、“不得”、“要求”、“应”、“不应”、“应”、“不应”、“建议”、“可”和“可选”应按照RFC 2119[RFC2119]中所述进行解释。
This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managing HDSL2/SHDSL lines.
本文档定义了一个管理信息库（MIB）模块，用于互联网社区中的网络管理协议，用于管理HDSL2/SHDSL线路。
The MIB module described in RFC 3276 [RFC3276] describes objects used for managing High Bit-Rate DSL - 2nd generation (HDSL2) [T1E1.4] and Single-Pair High-Speed Digital Subscriber Line (SHDSL) interfaces [G.991.2]. These object descriptions are based upon the specifications for the HDSL2 and SHDSL Embedded Operations Channel (EOC), as defined in the American National Standards Institute (ANSI) T1E1.4/2000-006 [T1E1.4] and International Telecommunication Union (ITU) G.991.2 [G.991.2].
RFC 3276[RFC3276]中描述的MIB模块描述了用于管理第二代高速数字用户线（HDSL2）[T1E1.4]和单对高速数字用户线（SHDSL）接口[G.991.2]的对象。这些对象描述基于美国国家标准协会（ANSI）T1E1.4/2000-006[T1E1.4]和国际电信联盟（ITU）G.991.2[G.991.2]中定义的HDSL2和SHDSL嵌入式操作信道（EOC）规范。
This document obsoletes RFC 3276 [RFC3276], which supports G.shdsl in that the MIB module described herein supports G.shdsl.bis as described in the G.991.2 [G.991.2]. In addition, objects have been added to improve the management of SHDSL lines.
本文件淘汰了RFC 3276[RFC3276]，后者支持G.shdsl，因为本文描述的MIB模块支持G.991.2[G.991.2]中描述的G.shdsl.bis。此外，还添加了对象以改进SHDSL线路的管理。
The MIB module is located in the MIB tree under MIB 2 transmission, as discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section of this document.
MIB模块位于MIB 2传输下的MIB树中，如本文件MIB-2集成（RFC 2863[RFC2863]）一节所述。
This section outlines the relationship of this MIB module with other MIB modules described in RFCs. Specifically, the IF-MIB, as presented in RFC 2863 [RFC2863], is discussed.
本节概述此MIB模块与RFCs中描述的其他MIB模块的关系。具体而言，将讨论RFC 2863[RFC2863]中所述的IF-MIB。
The HDSL2/SHDSL line MIB specifies the detailed attributes of a data interface. As such, it needs to integrate with RFC 2863 [RFC2863]. The IANA has assigned the following ifTypes to HDSL2 and SHDSL:
HDSL2/SHDSL行MIB指定数据接口的详细属性。因此，它需要与RFC 2863[RFC2863]集成。IANA已将以下IFTYPE分配给HDSL2和SHDSL：
IANAifType ::= TEXTUAL-CONVENTION
...
SYNTAX INTEGER {
...
hdsl2 (168), -- High Bit-Rate DSL, 2nd generation
shdsl (169), -- Multirate HDSL2
...
}
IANAifType ::= TEXTUAL-CONVENTION
...
SYNTAX INTEGER {
...
hdsl2 (168), -- High Bit-Rate DSL, 2nd generation
shdsl (169), -- Multirate HDSL2
...
}
Note that the ifFixedLengthGroup from RFC 2863 [RFC2863] MUST be supported and that the ifRcvAddressGroup does not apply to this MIB module.
请注意，必须支持来自RFC 2863[RFC2863]的ifFixedLengthGroup，并且IFRCVADDRESGROUP不适用于此MIB模块。
The MIB branch identified by this ifType contains tables appropriate for this interface type. Most such tables extend the ifEntry table and are indexed by ifIndex. For interfaces in systems implementing
此ifType标识的MIB分支包含适用于此接口类型的表。大多数这样的表扩展了ifEntry表，并由ifIndex索引。用于系统实现中的接口
this MIB module, those table entries indexed by ifIndex MUST be persistent.
在这个MIB模块中，那些由ifIndex索引的表项必须是持久的。
The following attributes are part of the mandatory ifGeneralInformationGroup in RFC 2863 [RFC2863] and are not duplicated in the HDSL2/SHDSL line MIB.
以下属性是RFC 2863[RFC2863]中必需的IFGeneralInformation组的一部分，在HDSL2/SHDSL行MIB中不重复。
===================================================================
===================================================================
ifIndex Interface index.
iIndex接口索引。
ifDescr See interfaces MIB [RFC2863].
ifDescr见接口MIB[RFC2863]。
ifType hdsl2(168) or shdsl(169).
ifType hdsl2（168）或shdsl（169）。
ifSpeed Set as appropriate. (This is fixed at 1552000 for HDSL2 lines)
如果速度设置合适。（HDSL2线路固定为1552000）
ifPhysAddress This object MUST have an octet string with zero length.
ifPhysAddress此对象必须具有长度为零的八位字节字符串。
ifAdminStatus See interfaces MIB [RFC2863].
ifAdminStatus见接口MIB[RFC2863]。
ifOperStatus See interfaces MIB [RFC2863].
ifOperStatus见接口MIB[RFC2863]。
ifLastChange See interfaces MIB [RFC2863].
iFastChange请参见接口MIB[RFC2863]。
ifName See interfaces MIB [RFC2863].
ifName见接口MIB[RFC2863]。
ifAlias See interfaces MIB [RFC2863].
IFALIA见接口MIB[RFC2863]。
ifLinkUpDownTrapEnable Default to enabled(1).
iFlinkUpDowntrap默认值为enabled（1）。
ifHighSpeed Set as appropriate. (For HDSL2 lines, this is fixed at 2)
如果高速设置合适。（对于HDSL2线路，固定为2）
ifConnectorPresent Set as appropriate.
ifConnectorPresent可根据需要进行设置。
===================================================================
Figure 1: Use of ifTable Objects
===================================================================
Figure 1: Use of ifTable Objects
The HDSL2-SHDSL-LINE-MIB module requires the allocation of a single object identifier for its MODULE-IDENTITY. The IANA has allocated this object identifier in the transmission subtree (48), defined in the SNMPv2-SMI MIB module.
HDSL2-SHDSL-LINE-MIB模块需要为其模块标识分配单个对象标识符。IANA已在SNMPv2 SMI MIB模块中定义的传输子树（48）中分配了该对象标识符。
The assignment was in fact done when RFC 3276 was published, and this revision of the RFC does not require any new action from IANA.
事实上，该任务是在RFC 3276发布时完成的，RFC的此次修订不需要IANA采取任何新的行动。
A. xtuC refers to a central site terminal unit;
H2TU-C for HDSL2, or STU-C for SHDSL.
B. xtuR refers to a remote site terminal unit;
H2TU-R for HDSL2, or STU-R for SHDSL.
C. xtu refers to a terminal unit; either an xtuC or xtuR.
D. xru refer to a regenerator unit;
H2RU for HDSL2, or SRU for SHDSL.
E. xU refers to any HDSL2/SHDSL unit; either an xtu or xru.
F. CRC is Cyclic Redundancy Check [G.991.2].
G. ES means Errored Second [G.991.2].
J. LOSW means Loss of Sync Word [G.991.2].
I. LOSWS means LOSW Seconds [G.991.2].
J. SES means Severely Errored Second [G.991.2].
K. SNR means Signal-to-Noise Ratio [G.991.2].
L. UAS means Unavailable Second [G.991.2].
A. xtuC refers to a central site terminal unit;
H2TU-C for HDSL2, or STU-C for SHDSL.
B. xtuR refers to a remote site terminal unit;
H2TU-R for HDSL2, or STU-R for SHDSL.
C. xtu refers to a terminal unit; either an xtuC or xtuR.
D. xru refer to a regenerator unit;
H2RU for HDSL2, or SRU for SHDSL.
E. xU refers to any HDSL2/SHDSL unit; either an xtu or xru.
F. CRC is Cyclic Redundancy Check [G.991.2].
G. ES means Errored Second [G.991.2].
J. LOSW means Loss of Sync Word [G.991.2].
I. LOSWS means LOSW Seconds [G.991.2].
J. SES means Severely Errored Second [G.991.2].
K. SNR means Signal-to-Noise Ratio [G.991.2].
L. UAS means Unavailable Second [G.991.2].
The following textual conventions are defined to reflect the line topology in the MIB module (further discussed in the following section) and to define the behavior of the statistics to be maintained by an agent.
定义以下文本约定是为了反映MIB模块中的线路拓扑（下一节将进一步讨论），并定义由代理维护的统计信息的行为。
o Hdsl2ShdslUnitId:
o Hdsl2ShdslUnitId：
Attributes with this syntax uniquely identify each unit in an HDSL2/SHDSL span. It mirrors the EOC addressing mechanism:
具有此语法的属性唯一标识HDSL2/SHDSL范围中的每个单元。它反映了EOC寻址机制：
xtuC(1) - central office (CO) terminal unit
xtuR(2) - customer premises equipment (CPE)
terminal unit
xru1(3) .. xru8(10) - regenerators, numbered from
central office side
xtuC(1) - central office (CO) terminal unit
xtuR(2) - customer premises equipment (CPE)
terminal unit
xru1(3) .. xru8(10) - regenerators, numbered from
central office side
o Hdsl2ShdslUnitSide:
o Hdsl2ShdslUnitSide：
Attributes with this syntax reference the two sides of a unit:
具有此语法的属性引用单元的两侧：
networkSide(1) - N in figure 2, below
customerSide(2) - C in figure 2, below
networkSide(1) - N in figure 2, below
customerSide(2) - C in figure 2, below
o Hdsl2ShdslWirePair:
o Hdsl2ShdslWirePair：
Attributes with this syntax reference the wire pairs connecting the units:
具有此语法的属性引用连接单元的线对：
wirePair1(1) - First pair for HDSL2/SHDSL. wirePair2(2) - Optional second pair for SHDSL only. wirePair3(3) - Optional third pair for SHDSL.bis only. wirePair4(4) - Optional fourth pair for SHDSL.bis only.
wirePair1（1）-HDSL2/SHDSL的第一对。wirePair2（2）-仅适用于SHDSL的可选第二对。wirePair3（3）-仅适用于SHDSL.bis的可选第三对。wirePair4（4）-仅适用于SHDSL.bis的可选第四对。
o Hdsl2ShdslTransmissionModeType:
o HDSL2SHDSLTransmissionModelType:
Attributes with this syntax specify the regional setting for an SHDSL line. Specified as a BITS construct, the two mode types are:
具有此语法的属性指定SHDSL线路的区域设置。指定为BITS结构，两种模式类型为：
region1 - ITU-T G.991.2 Annex A region2 - ITU-T G.991.2 Annex B
地区1-ITU-T G.991.2附录A地区2-ITU-T G.991.2附录B
o Hdsl2ShdslPerfCurrDayCount:
o Hdsl2ShdslPerfCurrDayCount：
Attributes with this syntax define the behavior of the 1-day (24 hour) gauges found in the MIB module.
具有此语法的属性定义MIB模块中的1天（24小时）量表的行为。
o Hdsl2Shdsl1DayIntervalCount:
o HDSL2SHDSL1日间隔计数：
Attributes with this syntax define the behavior of the 1-day (24 hour) interval counters found in the MIB module.
具有此语法的属性定义在MIB模块中找到的1天（24小时）间隔计数器的行为。
o Hdsl2ShdslPerfTimeElapsed:
o HDSL2SHDSLPerfTimeAppeased:
Attributes with this syntax define the behavior of the elapsed time counters found in the MIB module.
具有此语法的属性定义在MIB模块中找到的已用时间计数器的行为。
o Hdsl2ShdslPerfIntervalThreshold:
o Hdsl2ShdslPerfIntervalThreshold：
Attributes with this syntax define the behavior of the alarm thresholds found in the MIB module.
具有此语法的属性定义在MIB模块中找到的报警阈值的行为。
o Hdsl2ShdslClockReferenceType:
o Hdsl2ShdslClockReferenceType:
Attributes with this syntax define the clock references for the HDSL2/SHDSL span.
具有此语法的属性定义HDSL2/SHDSL范围的时钟参考。
The MIB module is structured into the following MIB groups:
MIB模块由以下MIB组构成：
o Span Configuration Group:
o Span配置组：
This group supports MIB objects for configuring parameters for the HDSL2/SHDSL span. It contains the following table:
此组支持用于配置HDSL2/SHDSL范围参数的MIB对象。它包含下表：
- hdsl2ShdslSpanConfTable
- HDSL2SHDSLSPANConfitable
o Span Status Group:
o Span状态组：
This group supports MIB objects for retrieving span status information. It contains the following table:
此组支持用于检索范围状态信息的MIB对象。它包含下表：
- hdsl2ShdslSpanStatusTable
- HDSL2SHDSLSPANSTAUSTABLE
o Unit Inventory Group:
o 单位库存组：
This group supports MIB objects for retrieving unit inventory information about units in HDSL2/SHDSL lines via the EOC. It contains the following table:
此组支持MIB对象，用于通过EOC检索HDSL2/SHDSL线路中设备的设备库存信息。它包含下表：
- hdsl2ShdslInventoryTable
- hdsl2ShdslInventoryTable
o Segment Endpoint Configuration Group:
o 段终结点配置组：
This group supports MIB objects for configuring parameters for the HDSL2/SHDSL segment endpoints. It contains the following table:
此组支持用于为HDSL2/SHDSL段端点配置参数的MIB对象。它包含下表：
- hdsl2ShdslEndpointConfTable
- hdsl2ShdslEndpointConfTable
o Segment Endpoint Current Status/Performance Group:
o 段端点当前状态/性能组：
This group supports MIB objects that provide the current status/ performance information relating to segment endpoints. It contains the following table:
此组支持提供与段端点相关的当前状态/性能信息的MIB对象。它包含下表：
- hdsl2ShdslEndpointCurrTable
- hdsl2ShdslEndpointCurrTable
o Segment Endpoint 15-Minute Interval Status/Performance Group:
o 分段终点15分钟间隔状态/性能组：
This group supports MIB objects that provide historic status/ performance information relating to segment endpoints in 15-minute intervals. It contains the following table:
此组支持MIB对象，这些对象每隔15分钟提供与段端点相关的历史状态/性能信息。它包含下表：
- hdsl2Shdsl15MinIntervalTable
- HDSL2SHDSL15最小间隔
o Segment Endpoint 1-Day Interval Status/Performance Group:
o 分段终点1天间隔状态/绩效组：
This group supports MIB objects that provide historic status/ performance information relating to segment endpoints in 1-day intervals. It contains the following table:
此组支持MIB对象，这些对象每隔1天提供与段端点相关的历史状态/性能信息。它包含下表：
- hdsl2Shdsl1DayIntervalTable
- HDSL2SHDSL1日期间隔表
o Maintenance Group:
o 维修组：
This group supports MIB objects for performing maintenance operations such as loopbacks for HDSL2/SHDSL lines. It contains the following table(s):
此组支持用于执行维护操作（如HDSL2/SHDSL线路的环回）的MIB对象。它包含下表：
- hdsl2ShdslEndpointMaintTable - hdsl2ShdslUnitMaintTable
- hdsl2ShdslEndpointMaintTable-HDSL2SHDSluntMaintTable
o Span Configuration Profile Group:
o Span配置配置文件组：
This group supports MIB objects for defining configuration profiles for HDSL2/SHDSL spans. It contains the following table:
此组支持MIB对象，用于定义HDSL2/SHDSL范围的配置配置文件。它包含下表：
- hdsl2ShdslSpanConfProfileTable
- hdsl2ShdslSpanConfProfileTable
o Segment Endpoint Alarm Configuration Profile Group:
o 段端点报警配置配置文件组：
This group supports MIB objects for defining alarm configuration profiles for HDSL2/SHDSL segment endpoints. It contains the following table:
此组支持MIB对象，用于定义HDSL2/SHDSL段端点的报警配置文件。它包含下表：
- hdsl2ShdslEndpointAlarmConfProfileTable
- HDSL2SHDSLendPointAlarmConfProfile表
o Notifications Group:
o 通知组：
This group defines the notifications supported for HDSL2/SHDSL lines:
此组定义HDSL2/SHDSL线路支持的通知：
- hdsl2ShdslLoopAttenCrossing - hdsl2ShdslSNRMarginCrossing - hdsl2ShdslPerfESThresh - hdsl2ShdslPerfSESThresh - hdsl2ShdslPerfCRCanomaliesThresh - hdsl2ShdslPerfLOSWSThresh - hdsl2ShdslPerfUASThresh - hdsl2ShdslSpanInvalidNumRepeaters - hdsl2ShdslLoopbackFailure - hdsl2ShdslpowerBackoff - hdsl2ShdsldeviceFault
- HDSL2SHDSLLoopAttentinCrossing-hdsl2ShdslSNRMarginCrossing-hdsl2ShdslPerfESThresh-hdsl2ShdslPerfESThresh-HDSL2SHDSLperfectrCanomaliesthresh-HDSL2SHDSLPerfectrLoopsThresh-HDSL2SHDSLSpanivalidNumRepeaters-hdsl2ShdslLoopbackFailure-hdsl2ShdslpowerBackoff-hdsl2ShdsldeviceFault
- hdsl2ShdsldcContinuityFault - hdsl2ShdslconfigInitFailure - hdsl2ShdslprotocolInitFailure - hdsl2ShdslnoNeighborPresent - hdsl2ShdslLocalPowerLoss
- hdsl2ShdsldcContinuityFault-hdsl2ShdslconfigInitFailure-hdsl2ShdslprotocolInitFailure-hdsl2ShdslnoNeighborPresent-hdsl2ShdslLocalPowerLoss
o SHDSL Wire Pair Group:
o SHDSL线对组：
This group supports MIB objects that provide status of the SHDSL-specific wire pairs.
此组支持提供SHDSL特定线对状态的MIB对象。
- hdsl2ShdslEndpointCurrTipRingReversal - hdsl2ShdslEndpointCurrActivationState
- HDSL2SHDSLendPointCurrtipringReversion-HDSL2SHDSLendPointCurrtActivationState
o Payload Group:
o 有效载荷组：
This group supports MIB objects for retrieving payload rates that exclude any framing overhead.
此组支持MIB对象检索不包括任何帧开销的有效负载率。
- hdsl2ShdslStatusMaxAttainablePayloadRate - hdsl2ShdslStatusActualPayloadRate
- HDSL2SHDSLStatusMaxAcreatablePayloadRate-hdsl2ShdslStatusActualPayloadRate
An HDSL2/SHDSL line consists of a minimum of two units: xtuC (the central termination unit) and an xtuR (the remote termination unit). The line may optionally support up to 8 repeater/regenerator units (xru) as shown in the figure below.
HDSL2/SHDSL线路至少由两个单元组成：xtuC（中央终端单元）和xtuR（远程终端单元）。该生产线可选择支持多达8个中继器/再生器单元（xru），如下图所示。
<-- Network Side Customer Side -->
<-- Network Side Customer Side -->
|</////////////////// HDSL2/SHDSL Span ////////////////////>|
|</////////////////// HDSL2/SHDSL Span ////////////////////>|
<~~~> <~~~> HDSL2/SHDSL Segments <~~~>
<~~~> <~~~> HDSL2/SHDSL Segments <~~~>
+-------+ +-------+ +-------+ +-------+ +-------+
+ C=1=N C=1=N C=..1..=N C=1=N +
| xtuC | | xru1 | | xru2 | | xru8 | | xtuR |
+ C=2=N C=2=N C=..2..=N C=2=N +
+-------+ +-------+ +-------+ +-------+ +-------+
+-------+ +-------+ +-------+ +-------+ +-------+
+ C=1=N C=1=N C=..1..=N C=1=N +
| xtuC | | xru1 | | xru2 | | xru8 | | xtuR |
+ C=2=N C=2=N C=..2..=N C=2=N +
+-------+ +-------+ +-------+ +-------+ +-------+
Key: <////> HDSL2/SHDSL span
<~~~~> HDSL2/SHDSL segment
=1= HDSL2/SHDSL wire-pair-1
=2= SHDSL optional wire-pair-2 (Not applicable to HDSL2)
C Customer side segment endpoint (modem)
N Network side segment endpoint (modem)
Key: <////> HDSL2/SHDSL span
<~~~~> HDSL2/SHDSL segment
=1= HDSL2/SHDSL wire-pair-1
=2= SHDSL optional wire-pair-2 (Not applicable to HDSL2)
C Customer side segment endpoint (modem)
N Network side segment endpoint (modem)
Figure 2: General Topology for an HDSL2/SHDSL Line
图2:HDSL2/SHDSL线路的一般拓扑
For SNR Margin, Loop Attenuation, ES, SES, CRC anomalies, LOSW, and UAS, there are event counters, current 15-minute and 0 to 96 15- minute history bucket(s) of "interval-counters", as well as current and 0 to 30 previous 1-day interval-counter(s). Each current 15- minute event bucket has an associated threshold notification.
对于信噪比裕度、环路衰减、ES、SES、CRC异常、LOSW和UAS，有事件计数器、“间隔计数器”的当前15分钟和0至96 15分钟历史段，以及当前和0至30个前1天间隔计数器。每个当前的15分钟事件存储桶都有一个相关的阈值通知。
Unlike RFC 3593 [RFC3593] and RFC 2662 [RFC2662], there is no representation in the MIB module for invalid buckets. In those cases where the data for an interval is suspect or known to be invalid, the agent MUST NOT report the interval. If the current 15-minute event bucket is determined to be invalid, notifications based upon the value of the event bucket MUST NOT be generated.
与RFC 3593[RFC3593]和RFC 2662[RFC2662]不同，MIB模块中没有无效存储桶的表示。在怀疑或已知某个时间间隔的数据无效的情况下，代理不得报告该时间间隔。如果确定当前15分钟事件存储桶无效，则不得生成基于事件存储桶值的通知。
Not reporting an interval will result in holes in the associated table. For example, the table hdsl2Shdsl15MinIntervalTable is indexed by { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}. If interval 12 is determined to be invalid but intervals 11 and 13 are valid, a Get Next operation on the indices .1.1.1.1.11 would return indices .1.1.1.1.13.
不报告间隔将导致关联表中出现漏洞。例如，表HDSL2SHDSL15MiniIntervalTable由{ifIndex、HDSL2SHDSLINVENDINDEX、hdsl2ShdslEndpointSide、hdsl2ShdslEndpointWirePair、HDSL2SHDSL15MiniIntervalNumber}索引。如果确定区间12无效，但区间11和13有效，则对索引进行Get Next操作。1.1.1.1.11将返回索引。1.1.1.1.13。
There is no requirement for an agent to ensure a fixed relationship between the start of a 15-minute interval and any wall clock; however, some implementations may align the 15-minute intervals with
不要求代理人确保15分钟间隔的开始和任何挂钟之间的固定关系；然而，一些实现可能会将15分钟的间隔与
quarter hours. Likewise, an implementation may choose to align 1-day intervals with the start of a day.
一刻钟。同样，一个实现可以选择将一天的间隔与一天的开始对齐。
Counters are not reset when an xU is reinitialized, only when the agent is reset or reinitialized (or under specific request outside the scope of this MIB module).
当重新初始化xU时，计数器不会重置，仅当代理重置或重新初始化时（或在此MIB模块范围之外的特定请求下）才会重置。
As a managed node can handle a large number of xUs (e.g., hundreds or perhaps thousands of lines), provisioning every parameter on every xU may become burdensome. Moreover, most lines are provisioned identically with the same set of parameters. To simplify the provisioning process, this MIB module makes use of profiles. A profile is a set of parameters that can be shared by multiple lines using the same configuration.
由于受管节点可以处理大量xU（例如，数百或数千行），因此在每个xU上配置每个参数可能会变得很麻烦。此外，大多数行使用相同的参数集进行相同的设置。为了简化资源调配过程，此MIB模块使用配置文件。配置文件是一组参数，可由使用相同配置的多条线路共享。
The following profiles are used in this MIB module:
此MIB模块中使用以下配置文件：
o Span Configuration Profiles - Span configuration profiles contain parameters for configuring HDSL2/SHDSL spans. They are defined in the hdsl2ShdslSpanConfProfileTable. Since span configuration parameters are only applicable for SHDSL, the support for span configuration profiles is optional for HDSL2 interfaces.
o Span配置文件-Span配置文件包含用于配置HDSL2/SHDSL跨距的参数。它们在HDSL2SHDSLSPANConfProfile表中定义。由于span配置参数仅适用于SHDSL，因此对span配置文件的支持对于HDSL2接口是可选的。
Note that the configuration of the span dictates the behavior for each individual segment endpoint in the span. If a different configuration is provisioned for any given segment endpoint within the span, the new configuration for this segment endpoint will override the span configuration for this segment endpoint only.
请注意，跨度的配置决定了跨度中每个单独线段端点的行为。如果为范围内的任何给定段端点提供了不同的配置，则此段端点的新配置将仅覆盖此段端点的范围配置。
o Segment Endpoint Alarm Configuration Profiles - These profiles contain parameters for configuring alarm thresholds for HDSL2/ SHDSL segment endpoints. These profiles are defined in the hdsl2ShdslEndpointAlarmConfProfileTable.
o 段端点报警配置配置文件-这些配置文件包含用于配置HDSL2/SHDSL段端点报警阈值的参数。这些配置文件在HDSL2SHDSLendPointAlarmConfProfile表中定义。
The index value for this profile is a locally-unique administratively-assigned name for the profile having the textual convention 'SnmpAdminString' (RFC 3411 [RFC3411]).
此配置文件的索引值是具有文本约定“SnmpAdminString”（RFC 3411[RFC3411]）的配置文件的本地唯一管理分配名称。
One or more lines may be configured to share parameters of a single profile (e.g., hdsl2ShdslEndpointAlarmConfProfile = 'silver') by setting its hdsl2ShdslEndpointAlarmConfProfile objects to the value of this profile. If a change is made to the profile, all lines that refer to it will be reconfigured to the changed parameters. Before a profile can be deleted or taken out of service, it must be first unreferenced from all associated lines.
通过将其hdsl2ShdslEndpointAlarmConfProfile对象设置为此配置文件的值，可以将一条或多条线路配置为共享单个配置文件的参数（例如，hdsl2ShdslEndpointAlarmConfProfile='silver'）。如果对配置文件进行了更改，则引用该配置文件的所有行都将重新配置为更改后的参数。在删除或停止使用配置文件之前，必须先从所有关联行中取消引用该配置文件。
Implementations MUST provide a default profile whose name is 'DEFVAL' for each profile type. The values of the associated parameters will be vendor specific unless otherwise indicated in this document. Before a line's profiles have been set, these profiles will be automatically used by setting hdsl2ShdslEndpointAlarmConfProfile and hdsl2ShdslSpanConfProfile to 'DEFVAL' where appropriate. This default profile name, 'DEFVAL', is considered reserved in the context of profiles defined in this MIB module.
实现必须为每种配置文件类型提供一个名为“deffal”的默认配置文件。除非本文件另有说明，否则相关参数的值将根据供应商而定。在设置线路配置文件之前，将通过将hdsl2ShdslEndpointAlarmConfProfile和hdsl2ShdslSpanConfProfile设置为“DEFVAL”（如适用），自动使用这些配置文件。此默认配置文件名“deffal”在该MIB模块中定义的配置文件上下文中被认为是保留的。
Profiles are created, assigned, and deleted dynamically using the profile name and profile row status in each of the four profile tables.
使用四个配置文件表中的配置文件名称和配置文件行状态动态创建、分配和删除配置文件。
Profile changes MUST take effect immediately. These changes MAY result in a restart (hard reset or soft restart) of the units on the line.
配置文件更改必须立即生效。这些更改可能会导致机组重新启动（硬复位或软重启）。
The ability to generate the SNMP notifications coldStart/warmStart (per [RFC3418]), which are per agent (e.g., per Digital Subscriber Line Access Multiplexer, or DSLAM, in such a device), and linkUp/ linkDown (per [RFC2863]), which are per interface (i.e., HDSL2/SHDSL line) is required.
需要能够生成每个代理（例如，在这样的设备中，每个数字用户线路接入多路复用器或DSLAM）的SNMP通知coldStart/warmStart（per[RFC3418]）和每个接口（即HDSL2/SHDSL线路）的链路上/链路下（per[RFC2863]）。
A linkDown notification MAY be generated whenever any ES, SES, CRC anomaly, LOSW, or UAS event occurs. The corresponding linkUp notification MAY be sent when all link failure conditions are cleared.
每当发生任何ES、SES、CRC异常、LOSW或UAS事件时，都会生成链路关闭通知。当清除所有链路故障条件时，可能会发送相应的连接通知。
The notifications defined in this MIB module are for initialization failure and for the threshold crossings associated with the following events: ES, SES, CRC anomaly, LOSW, and UAS. Each threshold has its own enable/threshold value. When that value is 0, the notification is disabled.
此MIB模块中定义的通知用于初始化失败以及与以下事件相关的阈值交叉：ES、SES、CRC异常、LOSW和UAS。每个阈值都有自己的启用/阈值。当该值为0时，将禁用通知。
The hdsl2ShdslEndpointCurrStatus is a bitmask representing all outstanding error conditions associated with a particular segment endpoint. Note that since the status of remote endpoints is obtained via the EOC, this information may be unavailable for units that are unreachable via EOC during a line error condition. Therefore, not all conditions may always be included in its current status. Notifications corresponding to the bit fields in this object are defined.
hdsl2ShdslEndpointCurrStatus是一个位掩码，表示与特定段端点相关的所有未解决错误条件。请注意，由于远程端点的状态是通过EOC获得的，因此在线路错误情况下，对于无法通过EOC访问的单元，此信息可能不可用。因此，并非所有条件都可以始终包含在其当前状态中。定义了与此对象中的位字段相对应的通知。
Two alarm conditions, SNR Margin Alarm and Loop Attenuation Alarm, are organized in a manner slightly different from that implied in the EOC specifications. In the MIB module, these alarm conditions are
两种报警条件（SNR余量报警和环路衰减报警）的组织方式与EOC规范中暗示的方式略有不同。在MIB模块中，这些报警条件是
tied to the two thresholds, hdsl2ShdslEndpointThreshSNRMargin and hdsl2ShdslEndpointThreshLoopAttenuation, found in the hdsl2ShdslEndpointAlarmConfProfileTable. In the EOC, the alarm conditions associated with these thresholds are per unit. In the MIB module, these alarm conditions are per endpoint. For terminal units, this has no impact. For repeaters, this implies an implementation variance where the agent in the terminal unit is responsible for detecting a threshold crossing. As the reporting of a repeater detected alarm condition to the polling terminal unit occurs in the same EOC message as the reporting of the current SNR Margin and Loop Attenuation values, it is anticipated that this will have very little impact on agent implementation.
与hdsl2ShdslEndpointThreshSNRMargin和HDSL2SHDSLendPointThreshLoopAttachment这两个阈值相关，可在HDSL2SHDSLendPointAlarmConfProfile表中找到。在EOC中，与这些阈值相关的报警条件为每单位。在MIB模块中，这些报警条件是针对每个端点的。对于终端设备，这没有影响。对于中继器，这意味着实现差异，其中终端单元中的代理负责检测阈值交叉。由于向轮询终端单元报告中继器检测到的报警条件与报告当前SNR裕度和环路衰减值在同一EOC消息中发生，因此预计这对代理实现的影响很小。
A threshold notification occurs whenever the corresponding current 15-minute interval error counter becomes equal to, or exceeds, the threshold value. Only one notification SHOULD be sent per interval per interface. Since the current 15-minute counter is reset to 0 every 15 minutes, and if the condition persists, the notification may recur as often as every 15 minutes. For example, to get a notification whenever a "loss of" event occurs (but at most once every 15 minutes), set the corresponding threshold to 1. The agent will generate a notification when the event originally occurs.
每当相应的当前15分钟间隔错误计数器等于或超过阈值时，就会出现阈值通知。每个接口的每个间隔只能发送一个通知。由于当前15分钟计数器每15分钟重置为0，并且如果该情况持续存在，则该通知可能每15分钟重复一次。例如，要在“丢失”事件发生时（但最多每15分钟一次）获取通知，请将相应的阈值设置为1。代理将在事件最初发生时生成通知。
Notifications, other than the threshold notifications listed above, SHOULD be rate limited (throttled) such that there is at least a 1-minute gap between the generation of consecutive notifications of the same event. When notifications are rate limited, they are dropped and not queued for sending at a future time. This is intended to be a general rate-limiting statement for notifications that have no explicit rate-limiting assertions in this document otherwise.
除了上面列出的阈值通知之外，其他通知都应该是速率限制（限制）的，以便在生成同一事件的连续通知之间至少有1分钟的间隔。当通知受速率限制时，它们将被丢弃，而不会排队等待将来发送。对于本文档中没有明确的速率限制断言的通知，这是一个通用的速率限制声明。
Note that the Network Management System, or NMS, may receive a linkDown notification as well, if enabled (via ifLinkUpDownTrapEnable [RFC2863]). At the beginning of the next 15-minute interval, the counter is reset. When the first second goes by and the event occurs, the current interval bucket will be 1, which equals the threshold, and the notification will be sent again.
请注意，如果启用，网络管理系统（或NMS）也可能会收到链路关闭通知（通过iFlinkupDownTrappenable[RFC2863]）。在下一个15分钟间隔开始时，计数器复位。当第一秒过去并且事件发生时，当前间隔bucket将为1（等于阈值），并且将再次发送通知。
An hdsl2ShdslSpanInvalidNumRepeaters notification may be generated following completion of the discovery phase if the number of repeaters discovered on the line differs from the number of repeaters specified in hdsl2ShdslSpanConfNumRepeaters. For those conditions where the number of provisioned repeaters is greater than those encountered during span discovery, all table entries associated with the nonexistent repeaters are to be discarded. For those conditions where the number of provisioned repeaters is less than those
如果在线路上发现的中继器数量不同于hdsl2ShdslSpanConfNumRepeaters中指定的中继器数量，则在发现阶段完成后，可能会生成hdsl2ShdslSpanInvalidNumRepeaters通知。对于配置的中继器数量大于跨度发现期间遇到的中继器数量的情况，将丢弃与不存在的中继器关联的所有表项。对于配置的中继器数量小于以下条件：
encountered during span discovery, additional table entries are to be created using the default span configuration profile.
在span查找过程中遇到，将使用默认的span配置文件创建其他表项。
HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGIN
HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Unsigned32, Gauge32, NOTIFICATION-TYPE, Integer32, transmission FROM SNMPv2-SMI RowStatus, TEXTUAL-CONVENTION FROM SNMPv2-TC ifIndex FROM IF-MIB PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF;
从IF-MIB PerfCurrentCount导入模块标识、对象类型、计数器32、无符号32、仪表32、通知类型、整数32、从SNMPv2 SMI RowStatus的传输、从SNMPv2 TC ifIndex导入文本约定、从IF-MIB PerfCurrentCount导入PerfIntervalCount、从PerfHist TC MIB SNMPAdminInstalling导入SNMP-FRAMEWORK-MIB MODULE-COMPLIANCE、对象组、，来自SNMPv2 CONF的通知组；
hdsl2ShdslMIB MODULE-IDENTITY
LAST-UPDATED "200512070000Z" -- December 7, 2005
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org
WG-URL:
http://www.ietf.org/html.charters/adslmib-charter.html
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed
Sand Channel Systems
Postal: 1210-203 Westview Ln
Raleigh NC 27605 USA
Email: sneedmike@hotmail.com
Phone: +1 206 600 7022
hdsl2ShdslMIB MODULE-IDENTITY
LAST-UPDATED "200512070000Z" -- December 7, 2005
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org
WG-URL:
http://www.ietf.org/html.charters/adslmib-charter.html
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed
Sand Channel Systems
Postal: 1210-203 Westview Ln
Raleigh NC 27605 USA
Email: sneedmike@hotmail.com
Phone: +1 206 600 7022
Co-Chair Bob Ray PESA Switching Systems, Inc.
Bob Ray PESA交换系统公司联合主席。
Postal 330-A Wynn Drive Huntsville, AL 35805 USA Phone +1 256 726 9200 ext. 142
邮政地址：美国阿拉巴马州亨茨维尔韦恩大道330号A邮编：35805电话+1 256 726 9200分机142
Co-editor: Clay Sikes Zhone Technologies, Inc. Postal: 8545 126th Ave. N. Largo, FL 33772 USA Email: csikes@zhone.com Phone: +1 727 530 8257
合编：Clay Sikes Zhone Technologies，Inc.邮政编码：8545美国佛罗里达州拉戈市第126大道，邮编：33772电子邮件：csikes@zhone.com电话：+1 727 530 8257
Co-editor: Bob Ray PESA Switching Systems, Inc. Postal: 330-A Wynn Drive Huntsville, AL 35805 USA Email: rray@pesa.com Phone: +1 256 726 9200 ext. 142
合编：Bob Ray PESA Switching Systems，Inc.邮政编码：330-A美国阿拉巴马州亨茨维尔永利大道A号邮编：35805电子邮件：rray@pesa.com电话：+12567269200分机142
Co-editor: Rajesh Abbi Alcatel USA Postal: 2301 Sugar Bush Road Raleigh, NC 27612-3339 USA
合编：Rajesh Abbi Alcatel美国邮政：美国北卡罗来纳州罗利糖布什路2301号，邮编：27612-3339
Email: Rajesh.Abbi@alcatel.com
Phone: +1 919 850 6194"
Email: Rajesh.Abbi@alcatel.com
Phone: +1 919 850 6194"
DESCRIPTION "This MIB module defines a collection of objects for managing HDSL2/SHDSL lines. An agent may reside at either end of the line; however, the MIB module is designed to require no management communication between the modems beyond that inherent in the low-level EOC line protocol as defined in ANSI T1E1.4/2000-006 (for HDSL2 lines) or in ITU G.991.2 (for SHDSL lines).
DESCRIPTION“此MIB模块定义了一组用于管理HDSL2/SHDSL线路的对象。代理可以驻留在线路的任意一端；但是，MIB模块的设计不需要调制解调器之间的管理通信，除了ANSI T1E1.4/2000-006（用于HDSL2线路）中定义的低级EOC线路协议中固有的通信之外或在ITU G.991.2中（用于SHDSL线路）。
Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC 4319; see the RFC itself for full legal notices."
版权所有（C）互联网协会（2005年）。此MIB模块的此版本是RFC 4319的一部分；有关完整的法律通知，请参见RFC本身。”
REVISION "200512070000Z" -- December 7, 2005 DESCRIPTION "This version, published as RFC 4319. The following changes have been made in this version: 1. Added a 3rd and 4th wire pair. 2. Modified all rates such that their rates are only constrained by an unsigned 32-bit value and not by what today's perceived technology limitations are.
修订版“2005120700Z”-2005年12月7日描述“此版本，作为RFC 4319发布。此版本中进行了以下更改：1.添加了第3和第4对导线。2.修改了所有速率，使其速率仅受无符号32位值的约束，而不受当今感知的技术限制的约束。
3. Clarified that the rates from RFC 3276 include payload and any applicable framing and added objects for payload-only rates. 4. Added an object to indicate whether the tip and ring are reversed on a wire pair. 5. Added an object to display the activation state of a wire pair. 6. Added references as necessary for clarification. 7. Added display hints to textual conventions as necessary. 8. Updated conformance statements as necessary. 9. Some changes were due to IETF requirements and RFC generation tools."
3. 澄清RFC 3276中的速率包括有效载荷和任何适用的帧以及仅有效载荷速率的添加对象。4.添加了一个对象，以指示导线对上的尖端和环是否反转。5.添加了一个对象以显示线对的激活状态。6.添加澄清所需的参考资料。7.根据需要向文本约定添加显示提示。8.必要时更新一致性声明。9一些变化是由于IETF要求和RFC生成工具。”
REVISION "200205090000Z" -- May 9, 2002 DESCRIPTION "Initial version, published as RFC 3276."
修订版“20020509000Z”-2002年5月9日描述“初始版本，作为RFC 3276发布。”
::= { transmission 48 }
::= { transmission 48 }
hdsl2ShdslMibObjects OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 1 }
hdsl2ShdslMibObjects OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 1 }
-- Textual Conventions used in this MIB module --
--此MIB模块中使用的文本约定--
Hdsl2ShdslPerfCurrDayCount ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A gauge associated with interface performance measurements in
a current 1-day (24 hour) measurement interval.
Hdsl2ShdslPerfCurrDayCount ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A gauge associated with interface performance measurements in
a current 1-day (24 hour) measurement interval.
The value of this gauge starts at zero at the beginning of an interval and is increased when associated events occur, until the end of the 1-day interval. At that time, the value of the gauge is stored in the previous 1-day history interval, as defined in a companion object of type Hdsl2Shdsl1DayIntevalCount, and the current interval gauge is restarted at zero.
该仪表的值在间隔开始时从零开始，并在相关事件发生时增加，直到1天间隔结束。此时，仪表的值存储在前一个1天的历史间隔中，如Hdsl2Shdsl1DayIntevalCount类型的伴生对象中所定义，当前间隔仪表将在零处重新启动。
In the case where the agent has no valid data available for this interval, the corresponding object instance is not available, and upon a retrieval request, a corresponding error message shall be returned to indicate that this instance does not exist. Please note that zero is a valid value." SYNTAX Gauge32
如果代理在此时间间隔内没有可用的有效数据，则相应的对象实例不可用，并且在检索请求时，应返回相应的错误消息以指示此实例不存在。请注意，零是一个有效值
Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current DESCRIPTION "A counter associated with interface performance measurements during the most previous 1-day (24 hour) measurement interval. The value of this gauge is equal to the value of the current day gauge, as defined in a companion object of type Hdsl2ShdslPerfCurrDayCount, at the end of its most recent interval.
STATUS current DESCRIPTION“与前一天（24小时）测量间隔期间的接口性能测量相关联的计数器。此仪表的值等于当前仪表的值，如Hdsl2ShdslPerfCurrDayCount类型的伴生对象在其最近间隔结束时所定义。
In the case where the agent has no valid data available for this interval, the corresponding object instance is not available, and upon a retrieval request, a corresponding error message shall be returned to indicate that this instance does not exist." SYNTAX Gauge32
如果代理在此时间间隔内没有可用的有效数据，则相应的对象实例不可用，并且在检索请求时，应返回相应的错误消息以指示此实例不存在。”语法表32
Hdsl2ShdslPerfTimeElapsed ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as
an adjustment in the system's time-of-day clock or the addition
of a leap second, the current interval exceeds the maximum
value, the agent will return the maximum value.
Hdsl2ShdslPerfTimeElapsed ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as
an adjustment in the system's time-of-day clock or the addition
of a leap second, the current interval exceeds the maximum
value, the agent will return the maximum value.
For 15-minute intervals, the range is limited to (0..899). For 24-hour intervals, the range is limited to (0..86399)." SYNTAX Unsigned32(0..86399)
对于15分钟的间隔，范围限制为（0..899）。对于24小时间隔，范围限制为（0..86399）。“语法无符号32（0..86399）
Hdsl2ShdslPerfIntervalThreshold ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"This convention defines a range of values that may be set in
a fault threshold alarm control. As the number of seconds in
a 15-minute interval numbers at most 900, objects of this type
may have a range of 0...900, where the value of 0 disables the
alarm."
SYNTAX Unsigned32(0..900)
Hdsl2ShdslPerfIntervalThreshold ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"This convention defines a range of values that may be set in
a fault threshold alarm control. As the number of seconds in
a 15-minute interval numbers at most 900, objects of this type
may have a range of 0...900, where the value of 0 disables the
alarm."
SYNTAX Unsigned32(0..900)
Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the unique identification for all units in an
HDSL2/SHDSL span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
SYNTAX INTEGER
Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the unique identification for all units in an
HDSL2/SHDSL span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
SYNTAX INTEGER
{
xtuC(1),
xtuR(2),
xru1(3),
xru2(4),
xru3(5),
xru4(6),
xru5(7),
xru6(8),
xru7(9),
xru8(10)
}
{
xtuC(1),
xtuR(2),
xru1(3),
xru2(4),
xru3(5),
xru4(6),
xru5(7),
xru6(8),
xru7(9),
xru8(10)
}
Hdsl2ShdslUnitSide ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the referenced side of an HDSL2/SHDSL unit - Network
or Customer side. The side facing the Network is the Network
side, while the side facing the Customer is the Customer side."
SYNTAX INTEGER
{
networkSide(1),
customerSide(2)
}
Hdsl2ShdslUnitSide ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the referenced side of an HDSL2/SHDSL unit - Network
or Customer side. The side facing the Network is the Network
side, while the side facing the Customer is the Customer side."
SYNTAX INTEGER
{
networkSide(1),
customerSide(2)
}
Hdsl2ShdslWirePair ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the referenced pair of wires in an HDSL2/SHDSL segment.
HDSL2 only supports a single pair (wirePair1 or two wire),
SHDSL lines support an optional second pair (wirePair2 or four
wire), and G.shdsl.bis support an optional third pair
(wirePair3 or six wire) and an optional fourth pair
(wirePair4 or eight wire)."
SYNTAX INTEGER
{
wirePair1(1), -- two wire
wirePair2(2), -- four wire
wirePair3(3), -- six wire
wirePair4(4) -- eight wire
}
Hdsl2ShdslWirePair ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the referenced pair of wires in an HDSL2/SHDSL segment.
HDSL2 only supports a single pair (wirePair1 or two wire),
SHDSL lines support an optional second pair (wirePair2 or four
wire), and G.shdsl.bis support an optional third pair
(wirePair3 or six wire) and an optional fourth pair
(wirePair4 or eight wire)."
SYNTAX INTEGER
{
wirePair1(1), -- two wire
wirePair2(2), -- four wire
wirePair3(3), -- six wire
wirePair4(4) -- eight wire
}
Hdsl2ShdslTransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Contains the regional setting of the HDSL2/SHDSL span,
represented as a bit-map of possible settings. The various
bit positions are as follows:
Hdsl2ShdslTransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Contains the regional setting of the HDSL2/SHDSL span,
represented as a bit-map of possible settings. The various
bit positions are as follows:
Bit Meaning Description
1 region 1 Indicates ITU-T G.991.2 Annex A.
2 region 2 Indicates ITU-T G.991.2 Annex B."
SYNTAX BITS
{
region1(0),
region2(1)
}
Bit Meaning Description
1 region 1 Indicates ITU-T G.991.2 Annex A.
2 region 2 Indicates ITU-T G.991.2 Annex B."
SYNTAX BITS
{
region1(0),
region2(1)
}
Hdsl2ShdslClockReferenceType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The various STU-C symbol clock references for the
HDSL2/SHDSL span, represented as an enumeration."
SYNTAX INTEGER
{
localClk(1), -- Mode-1 per G991.2
networkClk(2), -- Mode-2 per G991.2
dataOrNetworkClk(3), -- Mode-3a per G991.2
dataClk(4) -- Mode-3b per G991.2
}
Hdsl2ShdslClockReferenceType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The various STU-C symbol clock references for the
HDSL2/SHDSL span, represented as an enumeration."
SYNTAX INTEGER
{
localClk(1), -- Mode-1 per G991.2
networkClk(2), -- Mode-2 per G991.2
dataOrNetworkClk(3), -- Mode-3a per G991.2
dataClk(4) -- Mode-3b per G991.2
}
-- Span Configuration Group --
--跨配置组--
hdsl2ShdslSpanConfTable OBJECT-TYPE SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry MAX-ACCESS not-accessible STATUS current
HDSL2SHDSLSPANCONTRY MAX-ACCESS的HDSL2SHDSLSPANConConfTable对象类型语法序列当前状态不可访问
DESCRIPTION
"This table supports overall configuration of HDSL2/SHDSL
spans. Entries in this table MUST be maintained in a
persistent manner."
::= { hdsl2ShdslMibObjects 1 }
DESCRIPTION
"This table supports overall configuration of HDSL2/SHDSL
spans. Entries in this table MUST be maintained in a
persistent manner."
::= { hdsl2ShdslMibObjects 1 }
hdsl2ShdslSpanConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslSpanConfTable. Each entry
represents the complete span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL
line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanConfTable 1 }
hdsl2ShdslSpanConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslSpanConfTable. Each entry
represents the complete span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL
line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanConfTable 1 }
Hdsl2ShdslSpanConfEntry ::=
SEQUENCE
{
hdsl2ShdslSpanConfNumRepeaters Unsigned32,
hdsl2ShdslSpanConfProfile SnmpAdminString,
hdsl2ShdslSpanConfAlarmProfile SnmpAdminString
}
Hdsl2ShdslSpanConfEntry ::=
SEQUENCE
{
hdsl2ShdslSpanConfNumRepeaters Unsigned32,
hdsl2ShdslSpanConfProfile SnmpAdminString,
hdsl2ShdslSpanConfAlarmProfile SnmpAdminString
}
hdsl2ShdslSpanConfNumRepeaters OBJECT-TYPE
SYNTAX Unsigned32(0..8)
UNITS "repeaters"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object provisions the number of repeaters/regenerators
in this HDSL2/SHDSL span."
::= { hdsl2ShdslSpanConfEntry 1 }
hdsl2ShdslSpanConfNumRepeaters OBJECT-TYPE
SYNTAX Unsigned32(0..8)
UNITS "repeaters"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object provisions the number of repeaters/regenerators
in this HDSL2/SHDSL span."
::= { hdsl2ShdslSpanConfEntry 1 }
hdsl2ShdslSpanConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is a pointer to a span configuration profile in the hdsl2ShdslSpanConfProfileTable, which applies to this span. The value of this object is the index of the referenced profile in the hdsl2ShdslSpanConfProfileTable. Note that span configuration profiles are only applicable to SHDSL lines.
hdsl2ShdslSpanConfProfile对象类型语法snmpadmin字符串（大小（1..32））MAX-ACCESS读写状态当前说明“此对象是指向适用于此范围的HDSL2SHDSLSpanConfProfile表中的范围配置配置文件的指针。此对象的值是HDSL2SHDSLSPANConfProfile表中引用的配置文件的索引。请注意，span配置文件仅适用于SHDSL线路。
HDSL2 lines MUST reference the default profile, 'DEFVAL'. By default, this object will have the value 'DEFVAL' (the index of the default profile).
HDSL2行必须引用默认配置文件“DEFVAL”。默认情况下，此对象的值为“deffal”（默认配置文件的索引）。
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslSpanConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 2 }
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslSpanConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 2 }
hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is a pointer to an alarm configuration profile in the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this object is the index of the referenced profile in the hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold configuration in the referenced profile will be
hdsl2ShdslSpanConfAlarmProfile对象类型语法SnmpAdminString（大小（1..32））最大访问读写状态当前说明“此对象是指向HDSL2SHDSLendPointAlarmConfProfile表中报警配置文件的指针。此对象的值是HDSL2SHDSLendPointAlarmConfProfile表中引用的配置文件的索引。参考配置文件中的报警阈值配置将为
used by default for all segment endpoints in this span. Individual endpoints may override this profile by explicitly specifying some other profile in the hdsl2ShdslEndpointConfTable. By default, this object will have the value 'DEFVAL' (the index of the default profile).
默认情况下用于此范围中的所有线段端点。各个端点可以通过在hdsl2ShdslEndpointConfTable中显式指定某些其他配置文件来覆盖此配置文件。默认情况下，此对象的值为“deffal”（默认配置文件的索引）。
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 3 }
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 3 }
-- Span Status Group --
--Span状态组--
hdsl2ShdslSpanStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides overall status information of
HDSL2/SHDSL spans. This table contains live data from
equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 2 }
hdsl2ShdslSpanStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides overall status information of
HDSL2/SHDSL spans. This table contains live data from
equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 2 }
hdsl2ShdslSpanStatusEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslSpanStatusTable. Each entry
represents the complete span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL
line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanStatusTable 1 }
hdsl2ShdslSpanStatusEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslSpanStatusTable. Each entry
represents the complete span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL
line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanStatusTable 1 }
Hdsl2ShdslSpanStatusEntry ::=
SEQUENCE
{
hdsl2ShdslStatusNumAvailRepeaters Unsigned32,
hdsl2ShdslStatusMaxAttainableLineRate Unsigned32,
hdsl2ShdslStatusActualLineRate Unsigned32,
hdsl2ShdslStatusTransmissionModeCurrent
Hdsl2ShdslTransmissionModeType,
hdsl2ShdslStatusMaxAttainablePayloadRate Unsigned32,
hdsl2ShdslStatusActualPayloadRate Unsigned32
}
Hdsl2ShdslSpanStatusEntry ::=
SEQUENCE
{
hdsl2ShdslStatusNumAvailRepeaters Unsigned32,
hdsl2ShdslStatusMaxAttainableLineRate Unsigned32,
hdsl2ShdslStatusActualLineRate Unsigned32,
hdsl2ShdslStatusTransmissionModeCurrent
Hdsl2ShdslTransmissionModeType,
hdsl2ShdslStatusMaxAttainablePayloadRate Unsigned32,
hdsl2ShdslStatusActualPayloadRate Unsigned32
}
hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE
SYNTAX Unsigned32(0..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual number of repeaters/regenerators
discovered in this HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 1 }
hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE
SYNTAX Unsigned32(0..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual number of repeaters/regenerators
discovered in this HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 1 }
hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the maximum attainable line rate in this HDSL2/SHDSL
span. This object provides the maximum rate the line is
capable of achieving. This is based upon measurements made
during line probing. This rate includes payload (user data)
and any applicable framing overhead."
::= { hdsl2ShdslSpanStatusEntry 2 }
hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the maximum attainable line rate in this HDSL2/SHDSL
span. This object provides the maximum rate the line is
capable of achieving. This is based upon measurements made
during line probing. This rate includes payload (user data)
and any applicable framing overhead."
::= { hdsl2ShdslSpanStatusEntry 2 }
hdsl2ShdslStatusActualLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual line rate in this HDSL2/SHDSL span. This
SHOULD equal ifSpeed. This rate includes payload (user data)
and any applicable framing overhead"
::= { hdsl2ShdslSpanStatusEntry 3 }
hdsl2ShdslStatusActualLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual line rate in this HDSL2/SHDSL span. This
SHOULD equal ifSpeed. This rate includes payload (user data)
and any applicable framing overhead"
::= { hdsl2ShdslSpanStatusEntry 3 }
hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the current Power Spectral Density (PSD) regional
setting of the HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 4 }
hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the current Power Spectral Density (PSD) regional
setting of the HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 4 }
hdsl2ShdslStatusMaxAttainablePayloadRate OBJECT-TYPE SYNTAX Unsigned32(0..4294967295) UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION
HDSL2SHDSLStatusMaxAcreatablePayloadRate对象类型语法Unsigned32（0..4294967295）单位“bps”最大访问只读状态当前说明
"Contains the maximum attainable payload (user data)
line rate in this HDSL2/SHDSL span. This object provides
the maximum rate the line is capable of achieving. This
is based upon measurements made during line probing. Any
framing overhead is not included."
::= { hdsl2ShdslSpanStatusEntry 5 }
"Contains the maximum attainable payload (user data)
line rate in this HDSL2/SHDSL span. This object provides
the maximum rate the line is capable of achieving. This
is based upon measurements made during line probing. Any
framing overhead is not included."
::= { hdsl2ShdslSpanStatusEntry 5 }
hdsl2ShdslStatusActualPayloadRate OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual line rate in this HDSL2/SHDSL span. Any
framing overhead is not included."
::= { hdsl2ShdslSpanStatusEntry 6 }
hdsl2ShdslStatusActualPayloadRate OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual line rate in this HDSL2/SHDSL span. Any
framing overhead is not included."
::= { hdsl2ShdslSpanStatusEntry 6 }
-- Unit Inventory Group --
--单位库存组--
hdsl2ShdslInventoryTable OBJECT-TYPE SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table supports retrieval of unit inventory information available via the EOC from units in an HDSL2/SHDSL line.
hdsl2ShdslInventoryTable Hdsl2ShdslInventoryEntry的对象类型语法序列MAX-ACCESS不可访问状态当前描述“此表支持通过EOC从HDSL2/SHDSL线中的装置检索装置库存信息。
Entries in this table are dynamically created during the line discovery process. The life cycle for these entries is as follows:
此表中的条目是在行发现过程中动态创建的。这些条目的生命周期如下所示：
- xtu discovers a device, either a far-end xtu or an xru - an inventory table entry is created for the device - the line goes down for whatever reason - inventory table entries for unreachable devices are destroyed
- xtu发现一个设备，无论是远端xtu还是xru-为该设备创建一个资源清册表条目-无论出于何种原因，该行都会中断-无法访问的设备的资源清册表条目会被销毁
As these entries are created/destroyed dynamically, they
are NOT persistent."
::= { hdsl2ShdslMibObjects 3 }
As these entries are created/destroyed dynamically, they
are NOT persistent."
::= { hdsl2ShdslMibObjects 3 }
hdsl2ShdslInventoryEntry OBJECT-TYPE SYNTAX Hdsl2ShdslInventoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the hdsl2ShdslInventoryTable. Each entry
hdsl2ShdslInventoryEntry对象类型语法hdsl2ShdslInventoryEntry MAX-ACCESS不可访问状态当前描述“hdsl2ShdslInventoryTable中的一个条目。每个条目
represents inventory information for a single unit in an
HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslInventoryTable 1 }
represents inventory information for a single unit in an
HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslInventoryTable 1 }
Hdsl2ShdslInventoryEntry ::=
SEQUENCE
{
hdsl2ShdslInvIndex Hdsl2ShdslUnitId,
hdsl2ShdslInvVendorID OCTET STRING,
hdsl2ShdslInvVendorModelNumber OCTET STRING,
hdsl2ShdslInvVendorSerialNumber OCTET STRING,
hdsl2ShdslInvVendorEOCSoftwareVersion Integer32,
hdsl2ShdslInvStandardVersion Integer32,
hdsl2ShdslInvVendorListNumber OCTET STRING,
hdsl2ShdslInvVendorIssueNumber OCTET STRING,
hdsl2ShdslInvVendorSoftwareVersion OCTET STRING,
hdsl2ShdslInvEquipmentCode OCTET STRING,
hdsl2ShdslInvVendorOther OCTET STRING,
hdsl2ShdslInvTransmissionModeCapability
Hdsl2ShdslTransmissionModeType
}
Hdsl2ShdslInventoryEntry ::=
SEQUENCE
{
hdsl2ShdslInvIndex Hdsl2ShdslUnitId,
hdsl2ShdslInvVendorID OCTET STRING,
hdsl2ShdslInvVendorModelNumber OCTET STRING,
hdsl2ShdslInvVendorSerialNumber OCTET STRING,
hdsl2ShdslInvVendorEOCSoftwareVersion Integer32,
hdsl2ShdslInvStandardVersion Integer32,
hdsl2ShdslInvVendorListNumber OCTET STRING,
hdsl2ShdslInvVendorIssueNumber OCTET STRING,
hdsl2ShdslInvVendorSoftwareVersion OCTET STRING,
hdsl2ShdslInvEquipmentCode OCTET STRING,
hdsl2ShdslInvVendorOther OCTET STRING,
hdsl2ShdslInvTransmissionModeCapability
Hdsl2ShdslTransmissionModeType
}
hdsl2ShdslInvIndex OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table corresponds to a physical element
in an HDSL2/SHDSL span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
::= { hdsl2ShdslInventoryEntry 1 }
hdsl2ShdslInvIndex OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table corresponds to a physical element
in an HDSL2/SHDSL span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
::= { hdsl2ShdslInventoryEntry 1 }
hdsl2ShdslInvVendorID OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor ID as reported in an Inventory Response message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 25-32."
::= { hdsl2ShdslInventoryEntry 2 }
hdsl2ShdslInvVendorID OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor ID as reported in an Inventory Response message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 25-32."
::= { hdsl2ShdslInventoryEntry 2 }
hdsl2ShdslInvVendorModelNumber OBJECT-TYPE SYNTAX OCTET STRING(SIZE(12))
hdsl2ShdslInvVendorModelNumber对象类型语法八位字节字符串（大小（12））
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor model number as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 33-44."
::= { hdsl2ShdslInventoryEntry 3 }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor model number as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 33-44."
::= { hdsl2ShdslInventoryEntry 3 }
hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor serial number as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 45-56."
::= { hdsl2ShdslInventoryEntry 4 }
hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor serial number as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 45-56."
::= { hdsl2ShdslInventoryEntry 4 }
hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor EOC version as reported in a Discovery Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.2, Discovery response - Message ID
129, Octet 12."
::= { hdsl2ShdslInventoryEntry 5 }
hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor EOC version as reported in a Discovery Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.2, Discovery response - Message ID
129, Octet 12."
::= { hdsl2ShdslInventoryEntry 5 }
hdsl2ShdslInvStandardVersion OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Version of the HDSL2/SHDSL standard implemented, as reported
in an Inventory Response message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octet 2."
::= { hdsl2ShdslInventoryEntry 6 }
hdsl2ShdslInvStandardVersion OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Version of the HDSL2/SHDSL standard implemented, as reported
in an Inventory Response message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octet 2."
::= { hdsl2ShdslInventoryEntry 6 }
hdsl2ShdslInvVendorListNumber OBJECT-TYPE SYNTAX OCTET STRING(SIZE(3))
hdsl2ShdslInvVendorListNumber对象类型语法八位字符串（大小（3））
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor list number as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 3-5."
::= { hdsl2ShdslInventoryEntry 7 }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor list number as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 3-5."
::= { hdsl2ShdslInventoryEntry 7 }
hdsl2ShdslInvVendorIssueNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor issue number as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 6-7."
::= { hdsl2ShdslInventoryEntry 8 }
hdsl2ShdslInvVendorIssueNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor issue number as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 6-7."
::= { hdsl2ShdslInventoryEntry 8 }
hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(6))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor software version as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 8-13."
::= { hdsl2ShdslInventoryEntry 9 }
hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(6))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor software version as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 8-13."
::= { hdsl2ShdslInventoryEntry 9 }
hdsl2ShdslInvEquipmentCode OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(10))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Equipment code conforming to ANSI T1.213, Coded Identification
of Equipment Entities."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 14-23."
::= { hdsl2ShdslInventoryEntry 10 }
hdsl2ShdslInvEquipmentCode OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(10))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Equipment code conforming to ANSI T1.213, Coded Identification
of Equipment Entities."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 14-23."
::= { hdsl2ShdslInventoryEntry 10 }
hdsl2ShdslInvVendorOther OBJECT-TYPE SYNTAX OCTET STRING(SIZE(12))
HDSL2SHDSLINVENDOR其他对象类型语法八位字节字符串（大小（12））
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Other vendor information as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 57-68."
::= { hdsl2ShdslInventoryEntry 11 }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Other vendor information as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 57-68."
::= { hdsl2ShdslInventoryEntry 11 }
hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the transmission mode capability of the SHDSL unit."
::= { hdsl2ShdslInventoryEntry 12 }
hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the transmission mode capability of the SHDSL unit."
::= { hdsl2ShdslInventoryEntry 12 }
-- Segment Endpoint Configuration Group --
--段端点配置组--
hdsl2ShdslEndpointConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports configuration parameters for segment
endpoints in an HDSL2/SHDSL line. As this table is indexed
by ifIndex, it MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 4 }
hdsl2ShdslEndpointConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports configuration parameters for segment
endpoints in an HDSL2/SHDSL line. As this table is indexed
by ifIndex, it MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 4 }
hdsl2ShdslEndpointConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointConfTable. Each entry
represents a single segment endpoint in an HDSL2/SHDSL line.
It is indexed by the ifIndex of the HDSL2/SHDSL line, the
UnitId of the associated unit, the side of the unit, and the
wire pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair}
::= { hdsl2ShdslEndpointConfTable 1 }
hdsl2ShdslEndpointConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointConfTable. Each entry
represents a single segment endpoint in an HDSL2/SHDSL line.
It is indexed by the ifIndex of the HDSL2/SHDSL line, the
UnitId of the associated unit, the side of the unit, and the
wire pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair}
::= { hdsl2ShdslEndpointConfTable 1 }
Hdsl2ShdslEndpointConfEntry ::=
SEQUENCE
{
Hdsl2ShdslEndpointConfEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide, hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair, hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString }
hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide，hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair，hdsl2ShdslEndpointAlarmConfProfile SNMPAdministring}
hdsl2ShdslEndpointSide OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitSide
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The side of the unit associated with this segment endpoint --
Network/Customer side -- as per the Hdsl2ShdslUnitSide textual
convention."
::= { hdsl2ShdslEndpointConfEntry 1 }
hdsl2ShdslEndpointSide OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitSide
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The side of the unit associated with this segment endpoint --
Network/Customer side -- as per the Hdsl2ShdslUnitSide textual
convention."
::= { hdsl2ShdslEndpointConfEntry 1 }
hdsl2ShdslEndpointWirePair OBJECT-TYPE
SYNTAX Hdsl2ShdslWirePair
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The wire pair of the modem associated with this segment
endpoint as per the Hdsl2ShdslWirePair textual convention."
::= { hdsl2ShdslEndpointConfEntry 2 }
hdsl2ShdslEndpointWirePair OBJECT-TYPE
SYNTAX Hdsl2ShdslWirePair
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The wire pair of the modem associated with this segment
endpoint as per the Hdsl2ShdslWirePair textual convention."
::= { hdsl2ShdslEndpointConfEntry 2 }
hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures the alarm threshold values to be used for this segment endpoint. The values are obtained from the alarm configuration profile referenced by this object. The value of this object is the index of the referenced profile in the hdsl2ShdslEndpointAlarmConfProfileTable, or NULL (a zero-length SnmpAdminString). If the value is a zero-length SnmpAdminString, the endpoint uses the default Alarm Configuration Profile for the associated span as per the hdsl2ShdslSpanConfAlarmProfile object in the hdsl2ShdslSpanConfTable. The default value of this object is a zero-length SnmpAdminString.
hdsl2ShdslEndpointAlarmConfProfile对象类型语法SnmpAdminString（大小（0..32））最大访问读写状态当前说明“此对象配置用于此段端点的报警阈值。这些值来自此对象引用的报警配置配置文件。此对象的值是HDSL2SHDSLendPointAlarmConfProfile表中引用的配置文件的索引，或NULL（零长度SNMPAdministring）。如果该值为零长度SNMPAdministring，则端点将根据hdsl2ShdslSpanConfTable中的hdsl2ShdslSpanConfAlarmProfile对象，使用关联范围的默认报警配置文件。此对象的默认值为零长度snmpadmin字符串。
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslEndpointConfEntry 3 }
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslEndpointConfEntry 3 }
-- Segment Endpoint Current Status/Performance Group --
--段端点当前状态/性能组--
hdsl2ShdslEndpointCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains current status and performance information
for segment endpoints in HDSL2/SHDSL lines. As with other
tables in this MIB module indexed by ifIndex, entries in this
table MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 5 }
hdsl2ShdslEndpointCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains current status and performance information
for segment endpoints in HDSL2/SHDSL lines. As with other
tables in this MIB module indexed by ifIndex, entries in this
table MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 5 }
hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointCurrTable. Each entry
contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of the
HDSL2/SHDSL line, the UnitId of the associated unit, the side
of the unit, and the wire pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair }
::= { hdsl2ShdslEndpointCurrTable 1 }
hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointCurrTable. Each entry
contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of the
HDSL2/SHDSL line, the UnitId of the associated unit, the side
of the unit, and the wire pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair }
::= { hdsl2ShdslEndpointCurrTable 1 }
Hdsl2ShdslEndpointCurrEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointCurrAtn Integer32,
hdsl2ShdslEndpointCurrSnrMgn Integer32,
hdsl2ShdslEndpointCurrStatus BITS,
hdsl2ShdslEndpointES Counter32,
hdsl2ShdslEndpointSES Counter32,
hdsl2ShdslEndpointCRCanomalies Counter32,
hdsl2ShdslEndpointLOSWS Counter32,
hdsl2ShdslEndpointUAS Counter32,
hdsl2ShdslEndpointCurr15MinTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr15MinES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinSES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinCRCanomalies PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinLOSWS PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinUAS PerfCurrentCount,
hdsl2ShdslEndpointCurr1DayTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr1DayES
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DaySES
Hdsl2ShdslEndpointCurrEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointCurrAtn Integer32,
hdsl2ShdslEndpointCurrSnrMgn Integer32,
hdsl2ShdslEndpointCurrStatus BITS,
hdsl2ShdslEndpointES Counter32,
hdsl2ShdslEndpointSES Counter32,
hdsl2ShdslEndpointCRCanomalies Counter32,
hdsl2ShdslEndpointLOSWS Counter32,
hdsl2ShdslEndpointUAS Counter32,
hdsl2ShdslEndpointCurr15MinTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr15MinES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinSES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinCRCanomalies PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinLOSWS PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinUAS PerfCurrentCount,
hdsl2ShdslEndpointCurr1DayTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr1DayES
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DaySES
Hdsl2ShdslPerfCurrDayCount, hdsl2ShdslEndpointCurr1DayCRCanomalies Hdsl2ShdslPerfCurrDayCount, hdsl2ShdslEndpointCurr1DayLOSWS Hdsl2ShdslPerfCurrDayCount, hdsl2ShdslEndpointCurr1DayUAS Hdsl2ShdslPerfCurrDayCount, hdsl2ShdslEndpointCurrTipRingReversal INTEGER, hdsl2ShdslEndpointCurrActivationState INTEGER }
Hdsl2ShdslPerfCurrDayCount、hdsl2ShdslEndpointCurr1DayCRCanomalies Hdsl2ShdslPerfCurrDayCount、HDSL2SHDSLendPointCurr1DayLoss HDSL2SHDSLendPointCurr1DayCount、HDSL2SHDSLendPointCurr1DayCount、HDSL2SHDSLendPointCurrTIPRING反转整数、HDSL2SHDSL2SHDSLendPointCurrActivationState整数}
hdsl2ShdslEndpointCurrAtn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current loop attenuation for this endpoint as reported in
a Network or Customer Side Performance Status message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 1 }
hdsl2ShdslEndpointCurrAtn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current loop attenuation for this endpoint as reported in
a Network or Customer Side Performance Status message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 1 }
hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current SNR margin for this endpoint as reported in a
Status Response/SNR message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 2 }
hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current SNR margin for this endpoint as reported in a
Status Response/SNR message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 2 }
hdsl2ShdslEndpointCurrStatus OBJECT-TYPE
SYNTAX BITS
{
noDefect(0),
powerBackoff(1),
deviceFault(2),
dcContinuityFault(3),
snrMarginAlarm(4),
loopAttenuationAlarm(5),
loswFailureAlarm(6),
configInitFailure(7),
protocolInitFailure(8),
noNeighborPresent(9),
loopbackActive(10)
}
hdsl2ShdslEndpointCurrStatus OBJECT-TYPE
SYNTAX BITS
{
noDefect(0),
powerBackoff(1),
deviceFault(2),
dcContinuityFault(3),
snrMarginAlarm(4),
loopAttenuationAlarm(5),
loswFailureAlarm(6),
configInitFailure(7),
protocolInitFailure(8),
noNeighborPresent(9),
loopbackActive(10)
}
MAX-ACCESS read-only STATUS current DESCRIPTION "Contains the current state of the endpoint. This is a bit-map of possible conditions. The various bit positions are as follows:
MAX-ACCESS只读状态当前描述”包含端点的当前状态。这是可能条件的位图。各种位位置如下所示：
noDefect There are no defects on the line.
无缺陷生产线上没有缺陷。
powerBackoff Indicates enhanced Power Backoff.
powerBackoff表示增强的电源后退。
deviceFault Indicates that a vendor-dependent diagnostic or self-test fault has been detected.
deviceFault表示检测到供应商相关的诊断或自检故障。
dcContinuityFault Indicates vendor-dependent conditions that interfere with span powering such as short and open circuits.
dcContinuityFault表示干扰跨度供电的供应商相关条件，如短路和断路。
snrMarginAlarm Indicates that the SNR margin has dropped below the alarm threshold.
snrMarginAlarm表示SNR裕度已降至报警阈值以下。
loopAttenuationAlarm Indicates that the loop attenuation exceeds the alarm threshold.
LoopAttendationArm表示环路衰减超过报警阈值。
loswFailureAlarm Indicates a forward LOSW alarm.
loswFailureAlarm表示正向LOSW报警。
configInitFailure Endpoint failure during initialization due to paired endpoint not able to support requested configuration.
由于配对端点无法支持请求的配置，初始化期间configInitFailure端点失败。
protocolInitFailure Endpoint failure during initialization due to incompatible protocol used by the paired endpoint.
protocolInitFailure由于配对终结点使用的协议不兼容，在初始化期间终结点失败。
noNeighborPresent Endpoint failure during initialization due to no activation sequence detected from paired endpoint.
由于未从配对端点检测到激活序列，因此初始化期间非IGHBorPresent端点失败。
loopbackActive A loopback is currently active at this segment endpoint.
loopbackActive环回当前在此段端点处于活动状态。
This is intended to supplement ifOperStatus. Note that there is a 1:1 relationship between the status bits defined in this object and the notification thresholds defined elsewhere in this MIB module." REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
这是对ifOperStatus的补充。请注意，此对象中定义的状态位与此MIB模块中别处定义的通知阈值之间存在1:1的关系。“参考”HDSL2第7.5.3.7节；SHDSL第9.5.5.7节”
::= { hdsl2ShdslEndpointCurrEntry 3 }
::= { hdsl2ShdslEndpointCurrEntry 3 }
hdsl2ShdslEndpointES OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) on this endpoint since the xU
was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 4 }
hdsl2ShdslEndpointES OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) on this endpoint since the xU
was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 4 }
hdsl2ShdslEndpointSES OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) on this endpoint
since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 5 }
hdsl2ShdslEndpointSES OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) on this endpoint
since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 5 }
hdsl2ShdslEndpointCRCanomalies OBJECT-TYPE
SYNTAX Counter32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies on this endpoint since the xU was
last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 6 }
hdsl2ShdslEndpointCRCanomalies OBJECT-TYPE
SYNTAX Counter32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies on this endpoint since the xU was
last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 6 }
hdsl2ShdslEndpointLOSWS OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds on this endpoint
since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 7 }
hdsl2ShdslEndpointLOSWS OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds on this endpoint
since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 7 }
hdsl2ShdslEndpointUAS OBJECT-TYPE SYNTAX Counter32
hdsl2ShdslEndpointUAS对象类型语法计数器32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) on this endpoint since
the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 8 }
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) on this endpoint since
the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 8 }
hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in the current 15-minute interval."
::= { hdsl2ShdslEndpointCurrEntry 9 }
hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in the current 15-minute interval."
::= { hdsl2ShdslEndpointCurrEntry 9 }
hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) in the current 15-minute
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 10 }
hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) in the current 15-minute
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 10 }
hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) in the current
15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 11 }
hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) in the current
15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 11 }
hdsl2ShdslEndpointCurr15MinCRCanomalies OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "detected CRC Anomalies" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of CRC anomalies in the current 15-minute interval." REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
HDSL2SHDSLENDPOINTCURR15MINRCANOMALES对象类型语法PerfCurrentCount单元“检测到CRC异常”最大访问只读状态当前描述“当前15分钟间隔内的CRC异常计数”。参考“HDSL2第7.5.3.7节；SHDSL第9.5.5.7节”
::= { hdsl2ShdslEndpointCurrEntry 12 }
::= { hdsl2ShdslEndpointCurrEntry 12 }
hdsl2ShdslEndpointCurr15MinLOSWS OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds in the current
15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 13 }
hdsl2ShdslEndpointCurr15MinLOSWS OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds in the current
15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 13 }
hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) in the current 15-minute
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 14 }
hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) in the current 15-minute
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 14 }
hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds that have elapsed since the beginning of
the current 1-day interval."
::= { hdsl2ShdslEndpointCurrEntry 15 }
hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds that have elapsed since the beginning of
the current 1-day interval."
::= { hdsl2ShdslEndpointCurrEntry 15 }
hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 16 }
hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 16 }
hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE SYNTAX Hdsl2ShdslPerfCurrDayCount UNITS "seconds"
hdsl2ShdslEndpointCurr1DaySES对象类型语法Hdsl2ShdslPerfCurrDayCount单位“秒”
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 17 }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 17 }
hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the current day as measured
by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 18 }
hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the current day as measured
by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 18 }
hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 19 }
hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 19 }
hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 20 }
hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 20 }
hdsl2ShdslEndpointCurrTipRingReversal OBJECT-TYPE
SYNTAX INTEGER
{
normal(1),
reversed(2)
}
MAX-ACCESS read-only
hdsl2ShdslEndpointCurrTipRingReversal OBJECT-TYPE
SYNTAX INTEGER
{
normal(1),
reversed(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the state of the tip/ring for the
wire pair."
::= { hdsl2ShdslEndpointCurrEntry 21 }
STATUS current
DESCRIPTION
"This object indicates the state of the tip/ring for the
wire pair."
::= { hdsl2ShdslEndpointCurrEntry 21 }
hdsl2ShdslEndpointCurrActivationState OBJECT-TYPE
SYNTAX INTEGER
{
preActivation(1), -- PreTrain
activation(2), -- Training
data(3) -- Trained
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the activation or training state of
the wire pair."
REFERENCE "ITU-T G.991.2, Section 6.2 PMD Activation Sequence"
::= { hdsl2ShdslEndpointCurrEntry 22 }
hdsl2ShdslEndpointCurrActivationState OBJECT-TYPE
SYNTAX INTEGER
{
preActivation(1), -- PreTrain
activation(2), -- Training
data(3) -- Trained
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the activation or training state of
the wire pair."
REFERENCE "ITU-T G.991.2, Section 6.2 PMD Activation Sequence"
::= { hdsl2ShdslEndpointCurrEntry 22 }
-- Segment Endpoint 15-Minute Interval Status/Performance Group --
--分段终点15分钟间隔状态/性能组--
hdsl2Shdsl15MinIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 6 }
hdsl2Shdsl15MinIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 6 }
hdsl2Shdsl15MinIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2Shdsl15MinIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}
::= { hdsl2Shdsl15MinIntervalTable 1 }
hdsl2Shdsl15MinIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2Shdsl15MinIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}
::= { hdsl2Shdsl15MinIntervalTable 1 }
Hdsl2Shdsl15MinIntervalEntry ::=
SEQUENCE
{
hdsl2Shdsl15MinIntervalNumber Unsigned32,
Hdsl2Shdsl15MinIntervalEntry ::=
SEQUENCE
{
hdsl2Shdsl15MinIntervalNumber Unsigned32,
hdsl2Shdsl15MinIntervalES PerfIntervalCount, hdsl2Shdsl15MinIntervalSES PerfIntervalCount, hdsl2Shdsl15MinIntervalCRCanomalies PerfIntervalCount, hdsl2Shdsl15MinIntervalLOSWS PerfIntervalCount, hdsl2Shdsl15MinIntervalUAS PerfIntervalCount }
HDSL2SHDSL15MiniIntervales PerfIntervalCount，HDSL2SHDSL15MiniIntervales PerfIntervalCount，HDSL2SHDSL15MiniIntervalcCanomalies PerfIntervalCount，HDSL2SHDSL15MiniIntervallosWS PerfIntervalCount，HDSL2SHDSL15MiniIntervaluas PerfIntervalCount}
hdsl2Shdsl15MinIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Performance Data Interval number. Interval 1 is the most
recent previous interval; interval 96 is 24 hours ago.
Intervals 2..96 are optional."
::= { hdsl2Shdsl15MinIntervalEntry 1 }
hdsl2Shdsl15MinIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Performance Data Interval number. Interval 1 is the most
recent previous interval; interval 96 is 24 hours ago.
Intervals 2..96 are optional."
::= { hdsl2Shdsl15MinIntervalEntry 1 }
hdsl2Shdsl15MinIntervalES OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 2 }
hdsl2Shdsl15MinIntervalES OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 2 }
hdsl2Shdsl15MinIntervalSES OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 3 }
hdsl2Shdsl15MinIntervalSES OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 3 }
hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 4 }
hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 4 }
hdsl2Shdsl15MinIntervalLOSWS OBJECT-TYPE
HDSL2SHDSL15MiniIntervalLosWS对象类型
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 5 }
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 5 }
hdsl2Shdsl15MinIntervalUAS OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 6 }
hdsl2Shdsl15MinIntervalUAS OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 6 }
-- Segment Endpoint 1-Day Interval Status/Performance Group --
--分段终点1天间隔状态/绩效组--
hdsl2Shdsl1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 7 }
hdsl2Shdsl1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 7 }
hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2Shdsl1DayIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalNumber }
::= { hdsl2Shdsl1DayIntervalTable 1 }
hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2Shdsl1DayIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalNumber }
::= { hdsl2Shdsl1DayIntervalTable 1 }
Hdsl2Shdsl1DayIntervalEntry ::=
SEQUENCE
{
hdsl2Shdsl1DayIntervalNumber Unsigned32,
hdsl2Shdsl1DayIntervalMoniSecs Hdsl2ShdslPerfTimeElapsed,
Hdsl2Shdsl1DayIntervalEntry ::=
SEQUENCE
{
hdsl2Shdsl1DayIntervalNumber Unsigned32,
hdsl2Shdsl1DayIntervalMoniSecs Hdsl2ShdslPerfTimeElapsed,
hdsl2Shdsl1DayIntervalES Hdsl2Shdsl1DayIntervalCount, hdsl2Shdsl1DayIntervalSES Hdsl2Shdsl1DayIntervalCount, hdsl2Shdsl1DayIntervalCRCanomalies Hdsl2Shdsl1DayIntervalCount, hdsl2Shdsl1DayIntervalLOSWS Hdsl2Shdsl1DayIntervalCount, hdsl2Shdsl1DayIntervalUAS Hdsl2Shdsl1DayIntervalCount }
HDSL2SHDSL1日间隔数HDSL2SHDSL1日间隔数，HDSL2SHDSL1日间隔数HDSL2SHDSL1日间隔数，HDSL2SHDSL1日间隔数HDSL2SHDSL1日间隔数，HDSL2SHDSL1日间隔数HDSL2SHDSL1日间隔数，HDSL2SHDSL1日间隔值为HDSL2SHDSL1日间隔数}
hdsl2Shdsl1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"History Data Interval number. Interval 1 is the most
recent previous day; interval 30 is 30 days ago. Intervals
2..30 are optional."
::= { hdsl2Shdsl1DayIntervalEntry 1 }
hdsl2Shdsl1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"History Data Interval number. Interval 1 is the most
recent previous day; interval 30 is 30 days ago. Intervals
2..30 are optional."
::= { hdsl2Shdsl1DayIntervalEntry 1 }
hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time in the 1-day interval over which the
performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not
be collected for any reason."
::= { hdsl2Shdsl1DayIntervalEntry 2 }
hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time in the 1-day interval over which the
performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not
be collected for any reason."
::= { hdsl2Shdsl1DayIntervalEntry 2 }
hdsl2Shdsl1DayIntervalES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 3 }
hdsl2Shdsl1DayIntervalES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 3 }
hdsl2Shdsl1DayIntervalSES OBJECT-TYPE SYNTAX Hdsl2Shdsl1DayIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds (SES) during the 1-day
HDSL2SHDSL1DayIntervales对象类型语法Hdsl2Shdsl1DayIntervalCount单位“秒”最大访问只读状态当前描述“1天内严重错误秒数（SES）”
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 4 }
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 4 }
hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 5 }
hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 5 }
hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 6 }
hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 6 }
hdsl2Shdsl1DayIntervalUAS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the 1-day interval
as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 7 }
hdsl2Shdsl1DayIntervalUAS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the 1-day interval
as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 7 }
-- Maintenance Group --
--维修组--
hdsl2ShdslEndpointMaintTable OBJECT-TYPE SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table supports maintenance operations (e.g., loopbacks) to be performed on HDSL2/SHDSL segment endpoints. This table contains live data from equipment. As such, it is NOT
hdsl2ShdslEndpointMaintTable对象类型语法序列HDSL2SHDSLENDPOINTMAINTERY MAX-ACCESS不可访问状态当前描述“此表支持在HDSL2/SHDSL段端点上执行的维护操作（例如环回）。此表包含来自设备的实时数据。因此，它不是
persistent."
::= { hdsl2ShdslMibObjects 8 }
persistent."
::= { hdsl2ShdslMibObjects 8 }
hdsl2ShdslEndpointMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointMaintTable. Each entry
corresponds to a single segment endpoint and is indexed by the
ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
unit, and the side of the unit."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide }
::= { hdsl2ShdslEndpointMaintTable 1 }
hdsl2ShdslEndpointMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointMaintTable. Each entry
corresponds to a single segment endpoint and is indexed by the
ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
unit, and the side of the unit."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide }
::= { hdsl2ShdslEndpointMaintTable 1 }
Hdsl2ShdslEndpointMaintEntry ::=
SEQUENCE
{
hdsl2ShdslMaintLoopbackConfig INTEGER,
hdsl2ShdslMaintTipRingReversal INTEGER,
hdsl2ShdslMaintPowerBackOff INTEGER,
hdsl2ShdslMaintSoftRestart INTEGER
}
Hdsl2ShdslEndpointMaintEntry ::=
SEQUENCE
{
hdsl2ShdslMaintLoopbackConfig INTEGER,
hdsl2ShdslMaintTipRingReversal INTEGER,
hdsl2ShdslMaintPowerBackOff INTEGER,
hdsl2ShdslMaintSoftRestart INTEGER
}
hdsl2ShdslMaintLoopbackConfig OBJECT-TYPE
SYNTAX INTEGER
{
noLoopback(1),
normalLoopback(2),
specialLoopback(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls configuration of loopbacks for the
associated segment endpoint. The status of the loopback
is obtained via the hdsl2ShdslEndpointCurrStatus object."
::= { hdsl2ShdslEndpointMaintEntry 1 }
hdsl2ShdslMaintLoopbackConfig OBJECT-TYPE
SYNTAX INTEGER
{
noLoopback(1),
normalLoopback(2),
specialLoopback(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls configuration of loopbacks for the
associated segment endpoint. The status of the loopback
is obtained via the hdsl2ShdslEndpointCurrStatus object."
::= { hdsl2ShdslEndpointMaintEntry 1 }
hdsl2ShdslMaintTipRingReversal OBJECT-TYPE
SYNTAX INTEGER
{
normal(1),
reversed(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
hdsl2ShdslMaintTipRingReversal OBJECT-TYPE
SYNTAX INTEGER
{
normal(1),
reversed(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the state of the tip/ring pair at the
associated segment endpoint."
::= { hdsl2ShdslEndpointMaintEntry 2 }
"This object indicates the state of the tip/ring pair at the
associated segment endpoint."
::= { hdsl2ShdslEndpointMaintEntry 2 }
hdsl2ShdslMaintPowerBackOff OBJECT-TYPE
SYNTAX INTEGER
{
default(1),
enhanced(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the receiver at the associated
segment endpoint to operate in default or enhanced power
backoff mode."
::= { hdsl2ShdslEndpointMaintEntry 3 }
hdsl2ShdslMaintPowerBackOff OBJECT-TYPE
SYNTAX INTEGER
{
default(1),
enhanced(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the receiver at the associated
segment endpoint to operate in default or enhanced power
backoff mode."
::= { hdsl2ShdslEndpointMaintEntry 3 }
hdsl2ShdslMaintSoftRestart OBJECT-TYPE
SYNTAX INTEGER
{
ready(1),
restart(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object enables the manager to trigger a soft restart
of the modem at the associated segment endpoint. The
manager may only set this object to the 'restart(2)'
value, which initiates a restart. The agent will perform a
restart after approximately 5 seconds. Following the 5 second
period, the agent will restore the object to the 'ready(1)'
state."
::= { hdsl2ShdslEndpointMaintEntry 4 }
hdsl2ShdslMaintSoftRestart OBJECT-TYPE
SYNTAX INTEGER
{
ready(1),
restart(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object enables the manager to trigger a soft restart
of the modem at the associated segment endpoint. The
manager may only set this object to the 'restart(2)'
value, which initiates a restart. The agent will perform a
restart after approximately 5 seconds. Following the 5 second
period, the agent will restore the object to the 'ready(1)'
state."
::= { hdsl2ShdslEndpointMaintEntry 4 }
hdsl2ShdslUnitMaintTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslUnitMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports maintenance operations for units in a
HDSL2/SHDSL line. Entries in this table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 9 }
hdsl2ShdslUnitMaintTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslUnitMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports maintenance operations for units in a
HDSL2/SHDSL line. Entries in this table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 9 }
hdsl2ShdslUnitMaintEntry OBJECT-TYPE SYNTAX Hdsl2ShdslUnitMaintEntry
hdsl2ShdslUnitMaintEntry对象类型语法hdsl2ShdslUnitMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslUnitMaintTable. Each entry
corresponds to a single unit and is indexed by the
ifIndex of the HDSL2/SHDSL line and the UnitId of the
associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslUnitMaintTable 1 }
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslUnitMaintTable. Each entry
corresponds to a single unit and is indexed by the
ifIndex of the HDSL2/SHDSL line and the UnitId of the
associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslUnitMaintTable 1 }
Hdsl2ShdslUnitMaintEntry ::=
SEQUENCE
{
hdsl2ShdslMaintLoopbackTimeout Integer32,
hdsl2ShdslMaintUnitPowerSource INTEGER
}
Hdsl2ShdslUnitMaintEntry ::=
SEQUENCE
{
hdsl2ShdslMaintLoopbackTimeout Integer32,
hdsl2ShdslMaintUnitPowerSource INTEGER
}
hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE
SYNTAX Integer32(0..4095)
UNITS "minutes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the timeout value for loopbacks
initiated at segments endpoints contained in the associated
unit. A value of 0 disables the timeout."
::= { hdsl2ShdslUnitMaintEntry 1 }
hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE
SYNTAX Integer32(0..4095)
UNITS "minutes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the timeout value for loopbacks
initiated at segments endpoints contained in the associated
unit. A value of 0 disables the timeout."
::= { hdsl2ShdslUnitMaintEntry 1 }
hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE
SYNTAX INTEGER
{
local(1),
span(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the DC power source being used by the
associated unit."
::= { hdsl2ShdslUnitMaintEntry 2 }
hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE
SYNTAX INTEGER
{
local(1),
span(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the DC power source being used by the
associated unit."
::= { hdsl2ShdslUnitMaintEntry 2 }
-- Span Configuration Profile Group --
--Span配置配置文件组--
hdsl2ShdslSpanConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry MAX-ACCESS not-accessible STATUS current
hdsl2ShdslSpanConfProfileTable Hdsl2ShdslSpanConfProfileEntry的对象类型语法序列MAX-ACCESS不可访问状态当前
DESCRIPTION
"This table supports definitions of span configuration
profiles for SHDSL lines. HDSL2 does not support these
configuration options. This table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 10 }
DESCRIPTION
"This table supports definitions of span configuration
profiles for SHDSL lines. HDSL2 does not support these
configuration options. This table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 10 }
hdsl2ShdslSpanConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted using the row creation/deletion mechanism
via hdsl2ShdslSpanConfProfileRowStatus. If an active
entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
INDEX { IMPLIED hdsl2ShdslSpanConfProfileName }
::= { hdsl2ShdslSpanConfProfileTable 1 }
hdsl2ShdslSpanConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted using the row creation/deletion mechanism
via hdsl2ShdslSpanConfProfileRowStatus. If an active
entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
INDEX { IMPLIED hdsl2ShdslSpanConfProfileName }
::= { hdsl2ShdslSpanConfProfileTable 1 }
Hdsl2ShdslSpanConfProfileEntry ::=
SEQUENCE
{
hdsl2ShdslSpanConfProfileName SnmpAdminString,
hdsl2ShdslSpanConfWireInterface INTEGER,
hdsl2ShdslSpanConfMinLineRate Unsigned32,
hdsl2ShdslSpanConfMaxLineRate Unsigned32,
hdsl2ShdslSpanConfPSD INTEGER,
hdsl2ShdslSpanConfTransmissionMode
Hdsl2ShdslTransmissionModeType,
hdsl2ShdslSpanConfRemoteEnabled INTEGER,
hdsl2ShdslSpanConfPowerFeeding INTEGER,
hdsl2ShdslSpanConfCurrCondTargetMarginDown Integer32,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown Integer32,
hdsl2ShdslSpanConfCurrCondTargetMarginUp Integer32,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp Integer32,
hdsl2ShdslSpanConfUsedTargetMargins BITS,
hdsl2ShdslSpanConfReferenceClock
Hdsl2ShdslClockReferenceType,
hdsl2ShdslSpanConfLineProbeEnable INTEGER,
hdsl2ShdslSpanConfProfileRowStatus RowStatus
}
Hdsl2ShdslSpanConfProfileEntry ::=
SEQUENCE
{
hdsl2ShdslSpanConfProfileName SnmpAdminString,
hdsl2ShdslSpanConfWireInterface INTEGER,
hdsl2ShdslSpanConfMinLineRate Unsigned32,
hdsl2ShdslSpanConfMaxLineRate Unsigned32,
hdsl2ShdslSpanConfPSD INTEGER,
hdsl2ShdslSpanConfTransmissionMode
Hdsl2ShdslTransmissionModeType,
hdsl2ShdslSpanConfRemoteEnabled INTEGER,
hdsl2ShdslSpanConfPowerFeeding INTEGER,
hdsl2ShdslSpanConfCurrCondTargetMarginDown Integer32,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown Integer32,
hdsl2ShdslSpanConfCurrCondTargetMarginUp Integer32,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp Integer32,
hdsl2ShdslSpanConfUsedTargetMargins BITS,
hdsl2ShdslSpanConfReferenceClock
Hdsl2ShdslClockReferenceType,
hdsl2ShdslSpanConfLineProbeEnable INTEGER,
hdsl2ShdslSpanConfProfileRowStatus RowStatus
}
hdsl2ShdslSpanConfProfileName OBJECT-TYPE
hdsl2ShdslSpanConfProfileName对象类型
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is the unique index associated with this profile.
Entries in this table are referenced via the object
hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry."
::= { hdsl2ShdslSpanConfProfileEntry 1 }
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is the unique index associated with this profile.
Entries in this table are referenced via the object
hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry."
::= { hdsl2ShdslSpanConfProfileEntry 1 }
hdsl2ShdslSpanConfWireInterface OBJECT-TYPE
SYNTAX INTEGER
{
twoWire(1),
fourWire(2),
sixWire(3),
eightWire(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the two-wire or optional four-wire,
six-wire, or eight-wire operation for SHDSL lines."
DEFVAL { twoWire }
::= { hdsl2ShdslSpanConfProfileEntry 2 }
hdsl2ShdslSpanConfWireInterface OBJECT-TYPE
SYNTAX INTEGER
{
twoWire(1),
fourWire(2),
sixWire(3),
eightWire(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the two-wire or optional four-wire,
six-wire, or eight-wire operation for SHDSL lines."
DEFVAL { twoWire }
::= { hdsl2ShdslSpanConfProfileEntry 2 }
hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
UNITS "bps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps) and includes
both payload (user data) and any applicable framing overhead.
If the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the
maximum line rate, the line rate is considered
'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 3 }
hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
UNITS "bps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps) and includes
both payload (user data) and any applicable framing overhead.
If the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the
maximum line rate, the line rate is considered
'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 3 }
hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE SYNTAX Unsigned32(0..4294967295) UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION
hdsl2ShdslSpanConfMaxLineRate对象类型语法Unsigned32（0..4294967295）单位“bps”MAX-ACCESS读取创建状态当前说明
"This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps) and includes
both payload (user data) and any applicable framing overhead.
If the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the
maximum line rate, the line rate is considered
'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 4 }
"This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps) and includes
both payload (user data) and any applicable framing overhead.
If the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the
maximum line rate, the line rate is considered
'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 4 }
hdsl2ShdslSpanConfPSD OBJECT-TYPE
SYNTAX INTEGER
{
symmetric(1),
asymmetric(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures use of symmetric/asymmetric PSD (Power
Spectral Density) Mask for the associated SHDSL Line. Support
for symmetric PSD is mandatory for all supported data rates.
Support for asymmetric PSD is optional."
DEFVAL { symmetric }
::= { hdsl2ShdslSpanConfProfileEntry 5 }
hdsl2ShdslSpanConfPSD OBJECT-TYPE
SYNTAX INTEGER
{
symmetric(1),
asymmetric(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures use of symmetric/asymmetric PSD (Power
Spectral Density) Mask for the associated SHDSL Line. Support
for symmetric PSD is mandatory for all supported data rates.
Support for asymmetric PSD is optional."
DEFVAL { symmetric }
::= { hdsl2ShdslSpanConfProfileEntry 5 }
hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the regional setting for the SHDSL
line."
DEFVAL { { region1 } }
::= { hdsl2ShdslSpanConfProfileEntry 6 }
hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the regional setting for the SHDSL
line."
DEFVAL { { region1 } }
::= { hdsl2ShdslSpanConfProfileEntry 6 }
hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE
SYNTAX INTEGER
{
enabled(1),
disabled(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for remote management
of the units in an SHDSL line from the STU-R via the EOC."
hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE
SYNTAX INTEGER
{
enabled(1),
disabled(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for remote management
of the units in an SHDSL line from the STU-R via the EOC."
DEFVAL { enabled }
::= { hdsl2ShdslSpanConfProfileEntry 7 }
DEFVAL { enabled }
::= { hdsl2ShdslSpanConfProfileEntry 7 }
hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE
SYNTAX INTEGER
{
noPower(1),
powerFeed(2),
wettingCurrent(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for optional power
feeding in an SHDSL line."
DEFVAL { noPower }
::= { hdsl2ShdslSpanConfProfileEntry 8 }
hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE
SYNTAX INTEGER
{
noPower(1),
powerFeed(2),
wettingCurrent(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for optional power
feeding in an SHDSL line."
DEFVAL { noPower }
::= { hdsl2ShdslSpanConfProfileEntry 8 }
hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the downstream current condition target
SNR margin for an SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 9 }
hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the downstream current condition target
SNR margin for an SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 9 }
hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the downstream worst-case target SNR
margin for an SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 10 }
hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the downstream worst-case target SNR
margin for an SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 10 }
hdsl2ShdslSpanConfCurrCondTargetMarginUp OBJECT-TYPE SYNTAX Integer32(-10..21) UNITS "dB" MAX-ACCESS read-create
hdsl2ShdslSpanConfCurrCondTargetMarginUp对象类型语法整数32（-10..21）单位“dB”MAX-ACCESS读取创建
STATUS current
DESCRIPTION
"This object specifies the upstream current-condition target
SNR margin for an SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 11 }
STATUS current
DESCRIPTION
"This object specifies the upstream current-condition target
SNR margin for an SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 11 }
hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the upstream worst-case target SNR
margin for an SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 12 }
hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the upstream worst-case target SNR
margin for an SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 12 }
hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE
SYNTAX BITS
{
currCondDown(0),
worstCaseDown(1),
currCondUp(2),
worstCaseUp(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether a target SNR margin is enabled or
disabled. This is a bit-map of possible settings. The
various bit positions are as follows:
hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE
SYNTAX BITS
{
currCondDown(0),
worstCaseDown(1),
currCondUp(2),
worstCaseUp(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether a target SNR margin is enabled or
disabled. This is a bit-map of possible settings. The
various bit positions are as follows:
currCondDown - current-condition downstream target SNR margin enabled
currCondDown-当前条件下游目标信噪比裕度启用
worstCaseDown - worst-case downstream target SNR margin enabled
worstCaseDown-最坏情况下下游目标SNR余量已启用
currCondUp - current-condition upstream target SNR margin enabled
currCondUp-当前条件上游目标SNR余量已启用
worstCaseUp - worst-case upstream target SNR margin enabled."
worstCaseUp—最坏情况下上游目标SNR余量已启用。”
DEFVAL { { currCondDown } }
::= { hdsl2ShdslSpanConfProfileEntry 13 }
DEFVAL { { currCondDown } }
::= { hdsl2ShdslSpanConfProfileEntry 13 }
hdsl2ShdslSpanConfReferenceClock OBJECT-TYPE
SYNTAX Hdsl2ShdslClockReferenceType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the clock reference for the STU-C
in an SHDSL Line."
DEFVAL { localClk }
::= { hdsl2ShdslSpanConfProfileEntry 14 }
hdsl2ShdslSpanConfReferenceClock OBJECT-TYPE
SYNTAX Hdsl2ShdslClockReferenceType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the clock reference for the STU-C
in an SHDSL Line."
DEFVAL { localClk }
::= { hdsl2ShdslSpanConfProfileEntry 14 }
hdsl2ShdslSpanConfLineProbeEnable OBJECT-TYPE
SYNTAX INTEGER
{
disable(1),
enable(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for Line Probe of
the units in an SHDSL line. When Line Probe is enabled, the
system performs Line Probing to find the best possible
rate. If Line Probe is disabled, the rate adaptation phase
is skipped to shorten set up time."
DEFVAL { disable }
::= { hdsl2ShdslSpanConfProfileEntry 15 }
hdsl2ShdslSpanConfLineProbeEnable OBJECT-TYPE
SYNTAX INTEGER
{
disable(1),
enable(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for Line Probe of
the units in an SHDSL line. When Line Probe is enabled, the
system performs Line Probing to find the best possible
rate. If Line Probe is disabled, the rate adaptation phase
is skipped to shorten set up time."
DEFVAL { disable }
::= { hdsl2ShdslSpanConfProfileEntry 15 }
hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in this table per the semantics of RowStatus. If an
active entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
::= { hdsl2ShdslSpanConfProfileEntry 16 }
hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in this table per the semantics of RowStatus. If an
active entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
::= { hdsl2ShdslSpanConfProfileEntry 16 }
-- Segment Endpoint Alarm Configuration Profile group --
--段端点报警配置配置文件组--
hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current
HDSL2SHDSLendPointAlarmConfProfile的Hdsl2ShdslEndpointAlarmConfProfileEntry的hdsl2ShdslEndpointAlarmConfProfileTable对象类型语法序列MAX-ACCESS不可访问状态当前
DESCRIPTION
"This table supports definitions of alarm configuration
profiles for HDSL2/SHDSL segment endpoints. This table
MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 11 }
DESCRIPTION
"This table supports definitions of alarm configuration
profiles for HDSL2/SHDSL segment endpoints. This table
MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 11 }
hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single alarm configuration profile.
Each profile contains a set of parameters for setting alarm
thresholds for various performance attributes monitored at
HDSL2/SHDSL segment endpoints. Profiles may be created/deleted
using the row creation/deletion mechanism via
hdsl2ShdslEndpointAlarmConfProfileRowStatus. If an active
entry is referenced in either hdsl2ShdslSpanConfAlarmProfile
or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName }
::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 }
hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single alarm configuration profile.
Each profile contains a set of parameters for setting alarm
thresholds for various performance attributes monitored at
HDSL2/SHDSL segment endpoints. Profiles may be created/deleted
using the row creation/deletion mechanism via
hdsl2ShdslEndpointAlarmConfProfileRowStatus. If an active
entry is referenced in either hdsl2ShdslSpanConfAlarmProfile
or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName }
::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 }
Hdsl2ShdslEndpointAlarmConfProfileEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString,
hdsl2ShdslEndpointThreshLoopAttenuation Integer32,
hdsl2ShdslEndpointThreshSNRMargin Integer32,
hdsl2ShdslEndpointThreshES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshSES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshCRCanomalies Integer32,
hdsl2ShdslEndpointThreshLOSWS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshUAS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus
}
Hdsl2ShdslEndpointAlarmConfProfileEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString,
hdsl2ShdslEndpointThreshLoopAttenuation Integer32,
hdsl2ShdslEndpointThreshSNRMargin Integer32,
hdsl2ShdslEndpointThreshES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshSES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshCRCanomalies Integer32,
hdsl2ShdslEndpointThreshLOSWS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshUAS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus
}
hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is the unique index associated with this profile."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 }
hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is the unique index associated with this profile."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 }
hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the loop attenuation alarm threshold.
When the current value of hdsl2ShdslEndpointCurrAtn reaches
or exceeds this threshold, an hdsl2ShdslLoopAttenCrossing
MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 }
hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the loop attenuation alarm threshold.
When the current value of hdsl2ShdslEndpointCurrAtn reaches
or exceeds this threshold, an hdsl2ShdslLoopAttenCrossing
MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 }
hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the SNR margin alarm threshold.
When the current value of hdsl2ShdslEndpointCurrSnrMgn
reaches or drops below this threshold, a
hdsl2ShdslSNRMarginCrossing MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 }
hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the SNR margin alarm threshold.
When the current value of hdsl2ShdslEndpointCurrSnrMgn
reaches or drops below this threshold, a
hdsl2ShdslSNRMarginCrossing MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 }
hdsl2ShdslEndpointThreshES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
Errored Seconds (ES) within any given 15-minute performance
data collection interval. If the value of Errored Seconds
in a particular 15-minute collection interval reaches/
exceeds this value, an hdsl2ShdslPerfESThresh MAY be
generated. At most, one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 }
hdsl2ShdslEndpointThreshES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
Errored Seconds (ES) within any given 15-minute performance
data collection interval. If the value of Errored Seconds
in a particular 15-minute collection interval reaches/
exceeds this value, an hdsl2ShdslPerfESThresh MAY be
generated. At most, one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 }
hdsl2ShdslEndpointThreshSES OBJECT-TYPE SYNTAX Hdsl2ShdslPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION
HDSL2SHDSLendPointThreshes对象类型语法Hdsl2ShdslPerfIntervalThreshold单位“秒”最大访问读取创建状态当前描述
"This object configures the threshold for the number of
Severely Errored Seconds (SES) within any given 15-minute
performance data collection interval. If the value of
Severely Errored Seconds in a particular 15-minute collection
interval reaches/exceeds this value, an hdsl2ShdslPerfSESThresh
MAY be generated. At most, one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 }
"This object configures the threshold for the number of
Severely Errored Seconds (SES) within any given 15-minute
performance data collection interval. If the value of
Severely Errored Seconds in a particular 15-minute collection
interval reaches/exceeds this value, an hdsl2ShdslPerfSESThresh
MAY be generated. At most, one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 }
hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE
SYNTAX Integer32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
CRC anomalies within any given 15-minute performance data
collection interval. If the value of CRC anomalies in a
particular 15-minute collection interval reaches/exceeds
this value, an hdsl2ShdslPerfCRCanomaliesThresh MAY be
generated. At most, one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 }
hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE
SYNTAX Integer32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
CRC anomalies within any given 15-minute performance data
collection interval. If the value of CRC anomalies in a
particular 15-minute collection interval reaches/exceeds
this value, an hdsl2ShdslPerfCRCanomaliesThresh MAY be
generated. At most, one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 }
hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
Loss of Sync Word (LOSW) Seconds within any given 15-minute
performance data collection interval. If the value of LOSW
in a particular 15-minute collection interval reaches/exceeds
this value, an hdsl2ShdslPerfLOSWSThresh MAY be generated.
At most, one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 }
hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
Loss of Sync Word (LOSW) Seconds within any given 15-minute
performance data collection interval. If the value of LOSW
in a particular 15-minute collection interval reaches/exceeds
this value, an hdsl2ShdslPerfLOSWSThresh MAY be generated.
At most, one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 }
hdsl2ShdslEndpointThreshUAS OBJECT-TYPE SYNTAX Hdsl2ShdslPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION
hdsl2ShdslEndpointThreshUAS对象类型语法Hdsl2ShdslPerfIntervalThreshold单位“秒”最大读取创建状态当前说明
"This object configures the threshold for the number of
Unavailable Seconds (UAS) within any given 15-minute
performance data collection interval. If the value of UAS
in a particular 15-minute collection interval reaches/exceeds
this value, an hdsl2ShdslPerfUASThresh MAY be generated.
At most, one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 }
"This object configures the threshold for the number of
Unavailable Seconds (UAS) within any given 15-minute
performance data collection interval. If the value of UAS
in a particular 15-minute collection interval reaches/exceeds
this value, an hdsl2ShdslPerfUASThresh MAY be generated.
At most, one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 }
hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in this table as per the semantics of RowStatus.
If an active entry is referenced in either
hdsl2ShdslSpanConfAlarmProfile or
hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 }
hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in this table as per the semantics of RowStatus.
If an active entry is referenced in either
hdsl2ShdslSpanConfAlarmProfile or
hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 }
-- Notifications Group --
--通知组--
hdsl2ShdslNotifications OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 0 }
hdsl2ShdslNotifications OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 0 }
hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointThreshLoopAttenuation
}
STATUS current
DESCRIPTION
"This notification indicates that the loop attenuation
threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation
value) has been reached/exceeded for the HDSL2/SHDSL segment
endpoint."
::= { hdsl2ShdslNotifications 1 }
hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointThreshLoopAttenuation
}
STATUS current
DESCRIPTION
"This notification indicates that the loop attenuation
threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation
value) has been reached/exceeded for the HDSL2/SHDSL segment
endpoint."
::= { hdsl2ShdslNotifications 1 }
hdsl2ShdslSNRMarginCrossing NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointThreshSNRMargin
}
hdsl2ShdslSNRMarginCrossing NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointThreshSNRMargin
}
STATUS current
DESCRIPTION
"This notification indicates that the SNR margin threshold (as
per the hdsl2ShdslEndpointThreshSNRMargin value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 2 }
STATUS current
DESCRIPTION
"This notification indicates that the SNR margin threshold (as
per the hdsl2ShdslEndpointThreshSNRMargin value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 2 }
hdsl2ShdslPerfESThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointThreshES
}
STATUS current
DESCRIPTION
"This notification indicates that the errored seconds
threshold (as per the hdsl2ShdslEndpointThreshES value)
has been reached/exceeded for the HDSL2/SHDSL segment
endpoint."
::= { hdsl2ShdslNotifications 3 }
hdsl2ShdslPerfESThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointThreshES
}
STATUS current
DESCRIPTION
"This notification indicates that the errored seconds
threshold (as per the hdsl2ShdslEndpointThreshES value)
has been reached/exceeded for the HDSL2/SHDSL segment
endpoint."
::= { hdsl2ShdslNotifications 3 }
hdsl2ShdslPerfSESThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointThreshSES
}
STATUS current
DESCRIPTION
"This notification indicates that the severely errored seconds
threshold (as per the hdsl2ShdslEndpointThreshSES value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 4 }
hdsl2ShdslPerfSESThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointThreshSES
}
STATUS current
DESCRIPTION
"This notification indicates that the severely errored seconds
threshold (as per the hdsl2ShdslEndpointThreshSES value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 4 }
hdsl2ShdslPerfCRCanomaliesThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointThreshCRCanomalies
}
STATUS current
DESCRIPTION
"This notification indicates that the CRC anomalies threshold
(as per the hdsl2ShdslEndpointThreshCRCanomalies value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 5 }
hdsl2ShdslPerfCRCanomaliesThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointThreshCRCanomalies
}
STATUS current
DESCRIPTION
"This notification indicates that the CRC anomalies threshold
(as per the hdsl2ShdslEndpointThreshCRCanomalies value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 5 }
hdsl2ShdslPerfLOSWSThresh NOTIFICATION-TYPE
HDSL2SHDSLPerflossThresh通知类型
OBJECTS
{
hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointThreshLOSWS
}
STATUS current
DESCRIPTION
"This notification indicates that the LOSW Seconds threshold
(as per the hdsl2ShdslEndpointThreshLOSWS value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 6 }
OBJECTS
{
hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointThreshLOSWS
}
STATUS current
DESCRIPTION
"This notification indicates that the LOSW Seconds threshold
(as per the hdsl2ShdslEndpointThreshLOSWS value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 6 }
hdsl2ShdslPerfUASThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointThreshUAS
}
STATUS current
DESCRIPTION
"This notification indicates that the unavailable seconds
threshold (as per the hdsl2ShdslEndpointThreshUAS value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 7 }
hdsl2ShdslPerfUASThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointThreshUAS
}
STATUS current
DESCRIPTION
"This notification indicates that the unavailable seconds
threshold (as per the hdsl2ShdslEndpointThreshUAS value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 7 }
hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslSpanConfNumRepeaters
}
STATUS current
DESCRIPTION
"This notification indicates that a mismatch has been detected
between the number of repeater/regenerator units configured
for an HDSL2/SHDSL line via the hdsl2ShdslSpanConfNumRepeaters
object and the actual number of repeater/regenerator units
discovered via the EOC."
::= { hdsl2ShdslNotifications 8 }
hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslSpanConfNumRepeaters
}
STATUS current
DESCRIPTION
"This notification indicates that a mismatch has been detected
between the number of repeater/regenerator units configured
for an HDSL2/SHDSL line via the hdsl2ShdslSpanConfNumRepeaters
object and the actual number of repeater/regenerator units
discovered via the EOC."
::= { hdsl2ShdslNotifications 8 }
hdsl2ShdslLoopbackFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslMaintLoopbackConfig
}
STATUS current
DESCRIPTION
"This notification indicates that an endpoint maintenance
loopback command failed for an HDSL2/SHDSL segment."
hdsl2ShdslLoopbackFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslMaintLoopbackConfig
}
STATUS current
DESCRIPTION
"This notification indicates that an endpoint maintenance
loopback command failed for an HDSL2/SHDSL segment."
::= { hdsl2ShdslNotifications 9 }
::= { hdsl2ShdslNotifications 9 }
hdsl2ShdslpowerBackoff NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
powerBackoff in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."
::= { hdsl2ShdslNotifications 10 }
hdsl2ShdslpowerBackoff NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
powerBackoff in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."
::= { hdsl2ShdslNotifications 10 }
hdsl2ShdsldeviceFault NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
deviceFault in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."
::= { hdsl2ShdslNotifications 11 }
hdsl2ShdsldeviceFault NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
deviceFault in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."
::= { hdsl2ShdslNotifications 11 }
hdsl2ShdsldcContinuityFault NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 12 }
hdsl2ShdsldcContinuityFault NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 12 }
hdsl2ShdslconfigInitFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
configInitFailure in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
hdsl2ShdslconfigInitFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
configInitFailure in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 13 }
::= { hdsl2ShdslNotifications 13 }
hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
protocolInitFailure in the hdsl2ShdslEndpointCurrStatus
object for this endpoint has changed."
::= { hdsl2ShdslNotifications 14 }
hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
protocolInitFailure in the hdsl2ShdslEndpointCurrStatus
object for this endpoint has changed."
::= { hdsl2ShdslNotifications 14 }
hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 15 }
hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 15 }
hdsl2ShdslLocalPowerLoss NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslInvVendorID
}
STATUS current
DESCRIPTION
"This notification indicates impending unit failure due to
loss of local power (last gasp)."
::= { hdsl2ShdslNotifications 16 }
hdsl2ShdslLocalPowerLoss NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslInvVendorID
}
STATUS current
DESCRIPTION
"This notification indicates impending unit failure due to
loss of local power (last gasp)."
::= { hdsl2ShdslNotifications 16 }
-- conformance information --
--一致性信息--
hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 3 }
hdsl2ShdslGroups OBJECT IDENTIFIER ::=
{ hdsl2ShdslConformance 1 }
hdsl2ShdslCompliances OBJECT IDENTIFIER ::=
{ hdsl2ShdslConformance 2 }
hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 3 }
hdsl2ShdslGroups OBJECT IDENTIFIER ::=
{ hdsl2ShdslConformance 1 }
hdsl2ShdslCompliances OBJECT IDENTIFIER ::=
{ hdsl2ShdslConformance 2 }
-- agent compliance statements
--代理合规声明
hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for SNMP entities that implement HDSL2 and SHDSL. The version of SHDSL supported in this compliance statement is g.shdsl.
HDSL2SHDSLLINEMIB COMPLIANCE MODULE-COMPLIANCE STATUS不推荐使用说明“实施HDSL2和SHDSL的SNMP实体的符合性声明。此符合性声明中支持的SHDSL版本为g.SHDSL。
**** This compliance statement is deprecated. ****"
MODULE
MANDATORY-GROUPS
{
hdsl2ShdslSpanConfGroup,
hdsl2ShdslSpanStatusGroup,
hdsl2ShdslInventoryGroup,
hdsl2ShdslEndpointConfGroup,
hdsl2ShdslEndpointCurrGroup,
hdsl2Shdsl15MinIntervalGroup,
hdsl2Shdsl1DayIntervalGroup,
hdsl2ShdslMaintenanceGroup,
hdsl2ShdslEndpointAlarmConfGroup,
hdsl2ShdslNotificationGroup
}
**** This compliance statement is deprecated. ****"
MODULE
MANDATORY-GROUPS
{
hdsl2ShdslSpanConfGroup,
hdsl2ShdslSpanStatusGroup,
hdsl2ShdslInventoryGroup,
hdsl2ShdslEndpointConfGroup,
hdsl2ShdslEndpointCurrGroup,
hdsl2Shdsl15MinIntervalGroup,
hdsl2Shdsl1DayIntervalGroup,
hdsl2ShdslMaintenanceGroup,
hdsl2ShdslEndpointAlarmConfGroup,
hdsl2ShdslNotificationGroup
}
GROUP hdsl2ShdslInventoryShdslGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
组HDSL2SHDSLINVENTORYSHDLSGROUP DESCRIPTION“仅支持SHDSL线路的实现需要对该组的支持。”
GROUP hdsl2ShdslSpanShdslStatusGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
组HDSL2SHDSLspanSHDSLSStatusGroup DESCRIPTION“仅支持SHDSL线路的实现需要对该组的支持。”
GROUP hdsl2ShdslSpanConfProfileGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
组hdsl2ShdslSpanConfProfileGroup DESCRIPTION“仅支持SHDSL线路的实现需要对此组的支持。”
OBJECT hdsl2ShdslSpanConfWireInterface
SYNTAX INTEGER
{
twoWire(1),
fourWire(2)
}
DESCRIPTION
"An implementation only has to support the range as
applicable for the original g.shdsl specification defined
in RFC 3276."
OBJECT hdsl2ShdslSpanConfWireInterface
SYNTAX INTEGER
{
twoWire(1),
fourWire(2)
}
DESCRIPTION
"An implementation only has to support the range as
applicable for the original g.shdsl specification defined
in RFC 3276."
OBJECT hdsl2ShdslStatusMaxAttainableLineRate SYNTAX Unsigned32(0..4112000) DESCRIPTION "An implementation only has to support the range as applicable for the original g.shdsl specification defined in RFC 3276."
对象HDSL2SHDSLStatusMaxAcreatableLineRate语法Unsigned32（0..4112000）说明“实现只需支持RFC 3276中定义的原始g.shdsl规范的适用范围。”
OBJECT hdsl2ShdslStatusActualLineRate SYNTAX Unsigned32(0..4112000) DESCRIPTION "An implementation only has to support the range as applicable for the original g.shdsl specification defined in RFC 3276."
对象hdsl2ShdslStatusActualLineRate语法Unsigned32（0..4112000）说明“实现只需支持RFC 3276中定义的原始g.shdsl规范的适用范围。”
OBJECT hdsl2ShdslSpanConfMinLineRate SYNTAX Unsigned32(0..4112000) DESCRIPTION "An implementation only has to support the range as applicable for the original g.shdsl specification defined in RFC 3276."
对象hdsl2ShdslSpanConfMinLineRate语法Unsigned32（0..4112000）说明“实现只需支持RFC 3276中定义的原始g.shdsl规范适用的范围。”
OBJECT hdsl2ShdslSpanConfMaxLineRate SYNTAX Unsigned32(0..4112000) DESCRIPTION "An implementation only has to support the range as applicable for the original g.shdsl specification defined in RFC 3276."
对象hdsl2ShdslSpanConfMaxLineRate语法Unsigned32（0..4112000）说明“实现只需支持RFC 3276中定义的原始g.shdsl规范的适用范围。”
::= { hdsl2ShdslCompliances 1 }
::= { hdsl2ShdslCompliances 1 }
hdsl2GshdslbisLineMibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that implement HDSL2 and SHDSL. The version of SHDSL supported in this compliance statement is g.shdsl.bis." MODULE MANDATORY-GROUPS { hdsl2ShdslSpanConfGroup, hdsl2ShdslSpanStatusGroup, hdsl2ShdslInventoryGroup, hdsl2ShdslEndpointConfGroup, hdsl2ShdslEndpointCurrGroup, hdsl2Shdsl15MinIntervalGroup, hdsl2Shdsl1DayIntervalGroup, hdsl2ShdslMaintenanceGroup, hdsl2ShdslEndpointAlarmConfGroup,
HDSL2GSHDSLBISLINEMIB合规性模块-合规性状态当前描述“实施HDSL2和SHDSL的SNMP实体的合规性声明。此合规性声明中支持的SHDSL版本为g.SHDSL.bis。”模块必填项-组{hdsl2ShdslSpanConfGroup、hdsl2ShdslSpanStatusGroup、hdsl2ShdslInventoryGroup、hdsl2ShdslEndpointConfGroup、hdsl2ShdslEndpointCurrGroup、HDSL2SHDSL15MiniIntervalGroup、hdsl2Shdsl1DayIntervalGroup、HDSL2SHDSLMaintenance Group、hdsl2ShdslEndpointAlarmConfGroup、，
hdsl2ShdslNotificationGroup }
hdsl2ShdslNotificationGroup}
GROUP hdsl2ShdslInventoryShdslGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
组HDSL2SHDSLINVENTORYSHDLSGROUP DESCRIPTION“仅支持SHDSL线路的实现需要对该组的支持。”
GROUP hdsl2ShdslSpanShdslStatusGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
组HDSL2SHDSLspanSHDSLSStatusGroup DESCRIPTION“仅支持SHDSL线路的实现需要对该组的支持。”
GROUP hdsl2ShdslSpanConfProfileGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
组hdsl2ShdslSpanConfProfileGroup DESCRIPTION“仅支持SHDSL线路的实现需要对此组的支持。”
GROUP hdsl2ShdslWirePairGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
组hdsl2ShdslWirePairGroup DESCRIPTION“仅支持SHDSL线路的实现需要对此组的支持。”
GROUP hdsl2ShdslPayloadRateGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
组hdsl2ShdslPayloadRateGroup DESCRIPTION“仅支持SHDSL线路的实现需要对此组的支持。”
::= { hdsl2ShdslCompliances 2 }
::= { hdsl2ShdslCompliances 2 }
-- units of conformance --
--一致性单位--
hdsl2ShdslSpanConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslSpanConfNumRepeaters,
hdsl2ShdslSpanConfProfile,
hdsl2ShdslSpanConfAlarmProfile
}
STATUS current
DESCRIPTION
"This group supports objects for configuring span-related
parameters for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 1 }
hdsl2ShdslSpanConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslSpanConfNumRepeaters,
hdsl2ShdslSpanConfProfile,
hdsl2ShdslSpanConfAlarmProfile
}
STATUS current
DESCRIPTION
"This group supports objects for configuring span-related
parameters for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 1 }
hdsl2ShdslSpanStatusGroup OBJECT-GROUP OBJECTS
hdsl2ShdslSpanStatusGroup对象组对象
{
hdsl2ShdslStatusNumAvailRepeaters
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving span-related
status for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 2 }
{
hdsl2ShdslStatusNumAvailRepeaters
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving span-related
status for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 2 }
hdsl2ShdslInventoryShdslGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslInvTransmissionModeCapability
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
inventory information."
::= { hdsl2ShdslGroups 3 }
hdsl2ShdslInventoryShdslGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslInvTransmissionModeCapability
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
inventory information."
::= { hdsl2ShdslGroups 3 }
hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusMaxAttainableLineRate,
hdsl2ShdslStatusActualLineRate,
hdsl2ShdslStatusTransmissionModeCurrent
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
span-related status."
::= { hdsl2ShdslGroups 4 }
hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusMaxAttainableLineRate,
hdsl2ShdslStatusActualLineRate,
hdsl2ShdslStatusTransmissionModeCurrent
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
span-related status."
::= { hdsl2ShdslGroups 4 }
hdsl2ShdslInventoryGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslInvVendorID,
hdsl2ShdslInvVendorModelNumber,
hdsl2ShdslInvVendorSerialNumber,
hdsl2ShdslInvVendorEOCSoftwareVersion,
hdsl2ShdslInvStandardVersion,
hdsl2ShdslInvVendorListNumber,
hdsl2ShdslInvVendorIssueNumber,
hdsl2ShdslInvVendorSoftwareVersion,
hdsl2ShdslInvEquipmentCode,
hdsl2ShdslInvVendorOther
}
STATUS current
hdsl2ShdslInventoryGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslInvVendorID,
hdsl2ShdslInvVendorModelNumber,
hdsl2ShdslInvVendorSerialNumber,
hdsl2ShdslInvVendorEOCSoftwareVersion,
hdsl2ShdslInvStandardVersion,
hdsl2ShdslInvVendorListNumber,
hdsl2ShdslInvVendorIssueNumber,
hdsl2ShdslInvVendorSoftwareVersion,
hdsl2ShdslInvEquipmentCode,
hdsl2ShdslInvVendorOther
}
STATUS current
DESCRIPTION
"This group supports objects that provide unit inventory
information about the units in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 5 }
DESCRIPTION
"This group supports objects that provide unit inventory
information about the units in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 5 }
hdsl2ShdslEndpointConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrAtn
}
STATUS current
DESCRIPTION
"This group supports objects for configuring parameters for
segment endpoints in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 6 }
hdsl2ShdslEndpointConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrAtn
}
STATUS current
DESCRIPTION
"This group supports objects for configuring parameters for
segment endpoints in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 6 }
hdsl2ShdslEndpointCurrGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointCurrStatus,
hdsl2ShdslEndpointES,
hdsl2ShdslEndpointSES,
hdsl2ShdslEndpointCRCanomalies,
hdsl2ShdslEndpointLOSWS,
hdsl2ShdslEndpointUAS,
hdsl2ShdslEndpointCurr15MinTimeElapsed,
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointCurr1DayTimeElapsed,
hdsl2ShdslEndpointCurr1DayES,
hdsl2ShdslEndpointCurr1DaySES,
hdsl2ShdslEndpointCurr1DayCRCanomalies,
hdsl2ShdslEndpointCurr1DayLOSWS,
hdsl2ShdslEndpointCurr1DayUAS
}
STATUS current
DESCRIPTION
"This group supports objects that provide current status and
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 7 }
hdsl2ShdslEndpointCurrGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointCurrStatus,
hdsl2ShdslEndpointES,
hdsl2ShdslEndpointSES,
hdsl2ShdslEndpointCRCanomalies,
hdsl2ShdslEndpointLOSWS,
hdsl2ShdslEndpointUAS,
hdsl2ShdslEndpointCurr15MinTimeElapsed,
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointCurr1DayTimeElapsed,
hdsl2ShdslEndpointCurr1DayES,
hdsl2ShdslEndpointCurr1DaySES,
hdsl2ShdslEndpointCurr1DayCRCanomalies,
hdsl2ShdslEndpointCurr1DayLOSWS,
hdsl2ShdslEndpointCurr1DayUAS
}
STATUS current
DESCRIPTION
"This group supports objects that provide current status and
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 7 }
hdsl2Shdsl15MinIntervalGroup OBJECT-GROUP
HDSL2SHDSL15MiniIntervalGroup对象组
OBJECTS
{
hdsl2Shdsl15MinIntervalES,
hdsl2Shdsl15MinIntervalSES,
hdsl2Shdsl15MinIntervalCRCanomalies,
hdsl2Shdsl15MinIntervalLOSWS,
hdsl2Shdsl15MinIntervalUAS
}
STATUS current
DESCRIPTION
"This group supports objects that maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 15-minute intervals."
::= { hdsl2ShdslGroups 8 }
OBJECTS
{
hdsl2Shdsl15MinIntervalES,
hdsl2Shdsl15MinIntervalSES,
hdsl2Shdsl15MinIntervalCRCanomalies,
hdsl2Shdsl15MinIntervalLOSWS,
hdsl2Shdsl15MinIntervalUAS
}
STATUS current
DESCRIPTION
"This group supports objects that maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 15-minute intervals."
::= { hdsl2ShdslGroups 8 }
hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP
OBJECTS
{
hdsl2Shdsl1DayIntervalMoniSecs,
hdsl2Shdsl1DayIntervalES,
hdsl2Shdsl1DayIntervalSES,
hdsl2Shdsl1DayIntervalCRCanomalies,
hdsl2Shdsl1DayIntervalLOSWS,
hdsl2Shdsl1DayIntervalUAS
}
STATUS current
DESCRIPTION
"This group supports objects that maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 1-day intervals."
::= { hdsl2ShdslGroups 9 }
hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP
OBJECTS
{
hdsl2Shdsl1DayIntervalMoniSecs,
hdsl2Shdsl1DayIntervalES,
hdsl2Shdsl1DayIntervalSES,
hdsl2Shdsl1DayIntervalCRCanomalies,
hdsl2Shdsl1DayIntervalLOSWS,
hdsl2Shdsl1DayIntervalUAS
}
STATUS current
DESCRIPTION
"This group supports objects that maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 1-day intervals."
::= { hdsl2ShdslGroups 9 }
hdsl2ShdslMaintenanceGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslMaintLoopbackConfig,
hdsl2ShdslMaintTipRingReversal,
hdsl2ShdslMaintPowerBackOff,
hdsl2ShdslMaintSoftRestart,
hdsl2ShdslMaintLoopbackTimeout,
hdsl2ShdslMaintUnitPowerSource
}
STATUS current
DESCRIPTION
"This group supports objects that provide support for
maintenance actions for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 10 }
hdsl2ShdslMaintenanceGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslMaintLoopbackConfig,
hdsl2ShdslMaintTipRingReversal,
hdsl2ShdslMaintPowerBackOff,
hdsl2ShdslMaintSoftRestart,
hdsl2ShdslMaintLoopbackTimeout,
hdsl2ShdslMaintUnitPowerSource
}
STATUS current
DESCRIPTION
"This group supports objects that provide support for
maintenance actions for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 10 }
hdsl2ShdslEndpointAlarmConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointAlarmConfProfile,
hdsl2ShdslEndpointThreshLoopAttenuation,
hdsl2ShdslEndpointThreshSNRMargin,
hdsl2ShdslEndpointThreshES,
hdsl2ShdslEndpointThreshSES,
hdsl2ShdslEndpointThreshCRCanomalies,
hdsl2ShdslEndpointThreshLOSWS,
hdsl2ShdslEndpointThreshUAS,
hdsl2ShdslEndpointAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"This group supports objects that allow configuration of alarm
thresholds for various performance parameters for HDSL2/SHDSL
lines."
::= { hdsl2ShdslGroups 11 }
hdsl2ShdslEndpointAlarmConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointAlarmConfProfile,
hdsl2ShdslEndpointThreshLoopAttenuation,
hdsl2ShdslEndpointThreshSNRMargin,
hdsl2ShdslEndpointThreshES,
hdsl2ShdslEndpointThreshSES,
hdsl2ShdslEndpointThreshCRCanomalies,
hdsl2ShdslEndpointThreshLOSWS,
hdsl2ShdslEndpointThreshUAS,
hdsl2ShdslEndpointAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"This group supports objects that allow configuration of alarm
thresholds for various performance parameters for HDSL2/SHDSL
lines."
::= { hdsl2ShdslGroups 11 }
hdsl2ShdslNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS
{
hdsl2ShdslLoopAttenCrossing,
hdsl2ShdslSNRMarginCrossing,
hdsl2ShdslPerfESThresh,
hdsl2ShdslPerfSESThresh,
hdsl2ShdslPerfCRCanomaliesThresh,
hdsl2ShdslPerfLOSWSThresh,
hdsl2ShdslPerfUASThresh,
hdsl2ShdslSpanInvalidNumRepeaters,
hdsl2ShdslLoopbackFailure,
hdsl2ShdslpowerBackoff,
hdsl2ShdsldeviceFault,
hdsl2ShdsldcContinuityFault,
hdsl2ShdslconfigInitFailure,
hdsl2ShdslprotocolInitFailure,
hdsl2ShdslnoNeighborPresent,
hdsl2ShdslLocalPowerLoss
}
STATUS current
DESCRIPTION
"This group supports notifications of significant conditions
associated with HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 12 }
hdsl2ShdslNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS
{
hdsl2ShdslLoopAttenCrossing,
hdsl2ShdslSNRMarginCrossing,
hdsl2ShdslPerfESThresh,
hdsl2ShdslPerfSESThresh,
hdsl2ShdslPerfCRCanomaliesThresh,
hdsl2ShdslPerfLOSWSThresh,
hdsl2ShdslPerfUASThresh,
hdsl2ShdslSpanInvalidNumRepeaters,
hdsl2ShdslLoopbackFailure,
hdsl2ShdslpowerBackoff,
hdsl2ShdsldeviceFault,
hdsl2ShdsldcContinuityFault,
hdsl2ShdslconfigInitFailure,
hdsl2ShdslprotocolInitFailure,
hdsl2ShdslnoNeighborPresent,
hdsl2ShdslLocalPowerLoss
}
STATUS current
DESCRIPTION
"This group supports notifications of significant conditions
associated with HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 12 }
hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP OBJECTS
hdsl2ShdslSpanConfProfileGroup对象组对象
{
hdsl2ShdslSpanConfWireInterface,
hdsl2ShdslSpanConfMinLineRate,
hdsl2ShdslSpanConfMaxLineRate,
hdsl2ShdslSpanConfPSD,
hdsl2ShdslSpanConfTransmissionMode,
hdsl2ShdslSpanConfRemoteEnabled,
hdsl2ShdslSpanConfPowerFeeding,
hdsl2ShdslSpanConfCurrCondTargetMarginDown,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown,
hdsl2ShdslSpanConfCurrCondTargetMarginUp,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp,
hdsl2ShdslSpanConfUsedTargetMargins,
hdsl2ShdslSpanConfReferenceClock,
hdsl2ShdslSpanConfLineProbeEnable,
hdsl2ShdslSpanConfProfileRowStatus
}
STATUS current
DESCRIPTION
"This group supports objects that constitute configuration
profiles for configuring span-related parameters in SHDSL
lines."
::= { hdsl2ShdslGroups 13 }
{
hdsl2ShdslSpanConfWireInterface,
hdsl2ShdslSpanConfMinLineRate,
hdsl2ShdslSpanConfMaxLineRate,
hdsl2ShdslSpanConfPSD,
hdsl2ShdslSpanConfTransmissionMode,
hdsl2ShdslSpanConfRemoteEnabled,
hdsl2ShdslSpanConfPowerFeeding,
hdsl2ShdslSpanConfCurrCondTargetMarginDown,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown,
hdsl2ShdslSpanConfCurrCondTargetMarginUp,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp,
hdsl2ShdslSpanConfUsedTargetMargins,
hdsl2ShdslSpanConfReferenceClock,
hdsl2ShdslSpanConfLineProbeEnable,
hdsl2ShdslSpanConfProfileRowStatus
}
STATUS current
DESCRIPTION
"This group supports objects that constitute configuration
profiles for configuring span-related parameters in SHDSL
lines."
::= { hdsl2ShdslGroups 13 }
hdsl2ShdslWirePairGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrTipRingReversal,
hdsl2ShdslEndpointCurrActivationState
}
STATUS current
DESCRIPTION
"This group supports objects that provide the status
of SHDSL-specific wire pairs."
::= { hdsl2ShdslGroups 14 }
hdsl2ShdslWirePairGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrTipRingReversal,
hdsl2ShdslEndpointCurrActivationState
}
STATUS current
DESCRIPTION
"This group supports objects that provide the status
of SHDSL-specific wire pairs."
::= { hdsl2ShdslGroups 14 }
hdsl2ShdslPayloadRateGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusMaxAttainablePayloadRate,
hdsl2ShdslStatusActualPayloadRate
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving payload rates
that exclude any framing overhead."
::= { hdsl2ShdslGroups 15 }
hdsl2ShdslPayloadRateGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusMaxAttainablePayloadRate,
hdsl2ShdslStatusActualPayloadRate
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving payload rates
that exclude any framing overhead."
::= { hdsl2ShdslGroups 15 }
END
终止
A management application that supports RFC 3276 could mistakenly flag a unit that responds with a rate or wire pair that exceeds the ranges and/or enumerations specified in RFC 3276. For example, a G.shdsl.bis line with four wire pairs would report statistics for wire pairs that do not exist in RFC 3276. That is, a GET-NEXT request issues with the object identifier:
支持RFC 3276的管理应用程序可能会错误地标记响应速率或线对超过RFC 3276中指定的范围和/或枚举的单元。例如，具有四个线对的G.shdsl.bis线将报告RFC 3276中不存在的线对的统计信息。也就是说，GET-NEXT请求与对象标识符有关：
hdsl2ShdslEndpointCurrAtn.1.1.1.2
hdsl2ShdslEndpointCurrAtn.1.1.2
might return
可能会回来
hdsl2ShdslEndpointCurrAtn.1.1.1.3 = 0
hdsl2ShdslEndpointCurrAtn.1.1.3=0
with a G.shdsl.bis unit and
带有G.shdsl.bis装置和
hdsl2ShdslEndpointCurrSnrMgn.1.1.1.1 = 0
hdsl2ShdslEndpointCurrSnrMgn.1.1.1=0
with an HDSL2 unit as these objects are indexed by
使用HDSL2单元作为这些对象的索引
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslendpointSide, hdsl2ShdslEndpointWirePair }
索引{iIndex，hdsl2ShdslInvIndex，hdsl2ShdslendpointSide，hdsl2ShdslEndpointWirePair}
A management application intended to manage G.shdsl.bis agents SHOULD be modified to accept this sequence.
应修改旨在管理G.shdsl.bis代理的管理应用程序，以接受此序列。
One should note that this same unmodified management application is still capable of managing G.shdsl.bis agents albeit to the degree of G.SHDSL (non-bis) limitations. That is, it can create and monitor configurations limited to two wire pairs with an upper-rate limit of 4112000 bits/second.
应该注意的是，这个未经修改的管理应用程序仍然能够管理G.shdsl.bis代理，尽管受到G.shdsl（非bis）的限制。也就是说，它可以创建和监视限制为两个线对的配置，速率上限为4112000位/秒。
There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability:
此MIB模块中定义了许多管理对象，其MAX-ACCESS子句为read-write和/或read-create。在某些网络环境中，此类对象可能被视为敏感或易受攻击。在没有适当保护的非安全环境中支持SET操作可能会对网络操作产生负面影响。以下是表和对象及其敏感度/漏洞：
o hdsl2ShdslSpanConfTable
o HDSL2SHDSLSPANConfitable
The table consists of the following objects that support SET operations:
该表由以下支持集合操作的对象组成：
* hdsl2ShdslSpanConfNumRepeaters * hdsl2ShdslSpanConfProfile * hdsl2ShdslSpanConfAlarmProfile
* hdsl2ShdslSpanConfNumRepeaters*hdsl2ShdslSpanConfProfile*hdsl2ShdslSpanConfAlarmProfile
Unauthorized changes to hdsl2ShdslSpanConfNumRepeaters could result in an hdsl2ShdslSpanInvalidNumRepeaters notification. Note the discussion on hdsl2ShdslSpanInvalidNumRepeaters in the Notifications section above.
未经授权对hdsl2ShdslSpanConfNumRepeaters进行更改可能会导致hdsl2ShdslSpanInvalidNumRepeaters通知。注意上面通知部分中关于HDSL2SHDSLSpanInvalidNumRepeater的讨论。
Unauthorized changes to hdsl2ShdslSpanConfProfile could have an adverse operational effect on a span. Reference the hdsl2ShdslSpanConfProfileTable discussion below.
未经授权对hdsl2ShdslSpanConfProfile进行更改可能会对span产生不利的操作影响。请参考下面的hdsl2ShdslSpanConfProfileTable讨论。
Unauthorized changes to hdsl2ShdslSpanConfAlarmProfile could have a contrary effect on notifications. Reference the hdsl2ShdslEndpointAlarmConfProfileTable discussion below.
对hdsl2ShdslSpanConfAlarmProfile进行未经授权的更改可能会对通知产生相反的影响。请参考下面的HDSL2SHDSLendPointAlarmConfProfile表讨论。
o hdsl2ShdslEndpointConfTable
o hdsl2ShdslEndpointConfTable
This table contains one object, hdsl2ShdslEndpointAlarmConfProfile, that supports SET operations. Unauthorized changes could have an undesirable notifications. Reference the hdsl2ShdslEndpointAlarmConfProfileTable discussion below.
此表包含一个支持集合操作的对象hdsl2ShdslEndpointAlarmConfProfile。未经授权的更改可能会产生不需要的通知。请参考下面的HDSL2SHDSLendPointAlarmConfProfile表讨论。
o hdsl2ShdslEndpointMaintTable
o hdsl2ShdslEndpointMaintTable
The table consists of the following objects that support SET operations:
该表由以下支持集合操作的对象组成：
* hdsl2ShdslMaintLoopbackConfig * hdsl2ShdslMaintPowerBackoff * hdsl2ShdslMaintSoftRestart
* hdsl2ShdslMaintLoopbackConfig*hdsl2ShdslMaintPowerBackoff*hdsl2ShdslMaintSoftRestart
Unauthorized changes to hdsl2ShdslMaintLoopbackConfig could prevent end-to-end data transfer due to an activation of a loopback.
对hdsl2ShdslMaintLoopbackConfig进行未经授权的更改可能会由于激活环回而阻止端到端数据传输。
Unauthorized changes to hdsl2ShdslMaintPowerBackoff could result in an increased in bundle interference.
未经授权更改hdsl2ShdslMaintPowerBackoff可能会导致捆绑内干扰增加。
Unauthorized changes to hdsl2ShdslMaintSoftRestart could result in a temporary interruption of end-to-end data transfer as the result of the triggering of a soft restart.
对hdsl2ShdslMaintSoftRestart进行未经授权的更改可能会触发软重启，从而导致端到端数据传输暂时中断。
o hdsl2ShdslUnitMaintTable
o HDSL2SHDSLUNITMAINTABLE
This table contains one object, hdsl2ShdslMaintLoopbackTimeout, that supports SET operations. An unauthorized change to this object could result in the timeout value for loopbacks being increased, decreased, or disabled.
此表包含一个支持设置操作的对象hdsl2ShdslMaintLoopbackTimeout。对此对象进行未经授权的更改可能会导致环回超时值增加、减少或禁用。
o hdsl2ShdslSpanConfProfileTable
o hdsl2ShdslSpanConfProfileTable
The table consists of the following objects that support SET operations:
该表由以下支持集合操作的对象组成：
* hdsl2ShdslSpanConfWireInterface * hdsl2ShdslSpanConfMinLineRate * hdsl2ShdslSpanConfMaxLineRate * hdsl2ShdslSpanConfPSD * hdsl2ShdslSpanConfTransmissionMode * hdsl2ShdslSpanConfRemoteEnabled * hdsl2ShdslSpanConfPowerFeeding * hdsl2ShdslSpanConfCurrCondTargetMarginDown * hdsl2ShdslSpanConfWorstCaseTargetMarginDown * hdsl2ShdslSpanConfCurrCondTargetMarginUp * hdsl2ShdslSpanConfWorstCaseTargetMarginUp * hdsl2ShdslSpanConfUsedTargetMargins * hdsl2ShdslSpanConfReferenceClock * hdsl2ShdslSpanConfLineProbeEnable * hdsl2ShdslSpanConfProfileRowStatus
* hdsl2ShdslSpanConfWireInterface*hdsl2ShdslSpanConfMinLineRate*hdsl2ShdslSpanConfMaxLineRate*hdsl2ShdslSpanConfPSD*hdsl2ShdslSpanConfTransmissionMode*hdsl2ShdslSpanConfRemoteEnabled*hdsl2ShdslSpanConfPowerFeeding*hdsl2ShdslSpanConfCurrCondTargetMarginDown*hdsl2ShdslSpanConfWorstCaseTargetMarginDown*HDSL2SHDSLSPANConfCurrencConditTargetMarginup*hdsl2ShdslSpanConfWorstCaseTargetMarginUp*HDSL2SHDSLSPANConfLuxedTargetMarginup*HDSL2SHDSLSPANConfReferenceLock*HDSL2SHDSLSPANConfConflineproblem*hdsl2ShdslSpanConfProfileRowStatus
Setting any of the objects to an incorrect value could have an adverse operational effect on a span.
将任何对象设置为不正确的值都可能对跨度产生不利的操作影响。
Unauthorized changes to the hdsl2ShdslSpanConfWireInterface could result in the failure of a span to achieve activation to a state that would permit data flow. For example, setting this object to six-wire or eight-wire operation when one of the units in the span only supports two-wire or four-wire operation would likely prevent an expected end-to-end data transfer capability.
对HDSL2SHDSLSPANConfwire接口的未经授权的更改可能导致span无法激活到允许数据流的状态。例如，当跨度中的一个单元仅支持双线或四线操作时，将此对象设置为六线或八线操作可能会阻止预期的端到端数据传输能力。
Unauthorized changes to hdsl2ShdslSpanConfMinLineRate or hdsl2ShdslSpanConfMaxLineRate could have an adverse effect on performance. The range of allowable line rates could be altered such that the span may not be able to train to a line rate that
未经授权更改hdsl2ShdslSpanConfMinLineRate或hdsl2ShdslSpanConfMaxLineRate可能会对性能产生不利影响。允许线路速率的范围可以改变，以便跨度可能无法训练到
would permit any end-user data to traverse the span or the span could train to a line rate that is either greater than or less than the line rate that the provider has pledged.
将允许任何最终用户数据穿过跨度，或者跨度可以训练到大于或小于提供商承诺的线速率的线速率。
Unauthorized changes to hdsl2ShdslSpanConfPSD or hdsl2ShdslSpanConfTransmissionMode could have a detrimental effect on loop reach, performance, or spectral compatibility.
未经授权更改hdsl2ShdslSpanConfPSD或hdsl2ShdslSpanConfTransmissionMode可能会对环路范围、性能或频谱兼容性产生不利影响。
Unauthorized changes to hdsl2ShdslSpanConfRemoteEnable could alter the remote management ability of units.
对hdsl2ShdslSpanConfRemoteEnable进行未经授权的更改可能会改变设备的远程管理能力。
Unauthorized changes to hdsl2ShdslSpanConfPowerFeeding could shutdown units that are expected to be fed power remotely. Changing the configuration such that wetting current is not supplied may result in corrosion of electrical contacts.
对HDSL2SHDSLSPANConfPowerFeed进行未经授权的更改可能会关闭预期远程供电的装置。改变配置以不提供湿润电流可能会导致电触点腐蚀。
Unauthorized changes to hdsl2ShdslSpanConfCurrCondTargetMarginDown, hdsl2ShdslSpanConfWorstCaseTargetMarginDown, hdsl2ShdslSpanConfCurrCondTargetMarginUp, hdsl2ShdslSpanConfWorstCaseTargetMarginUp, or hdsl2ShdslSpanConfUsedTargetMargins could result in invalid parameters used to determine if a data rate can be supported under current and worst-case noise.
对hdsl2ShdslSpanConfCurrCondTargetMarginDown、hdsl2ShdslSpanConfWorstCaseTargetMarginDown、hdsl2ShdslSpanConfCurrCondTargetMarginUp、hdsl2ShdslSpanConfWorstCaseTargetMarginUp、hdsl2ShdslSpanConfWorstCaseTargetMarginUp的未经授权更改，或HDSL2SHDSLSPAN ConfusedTargetMargins可能导致用于确定在当前和最坏情况下是否支持数据速率的参数无效。
Unauthorized changes to hdsl2ShdslSpanConfReferenceClock could result in the selection of a clock source that might either prevent any data from being transferred or impair data transfer. In addition, an increase in CRC anomalies may be experienced.
未经授权对HDSL2SHDSLSpanConfReferenceLock进行更改可能会导致选择时钟源，该时钟源可能会阻止任何数据传输或影响数据传输。此外，CRC异常可能会增加。
Unauthorized changes to hdsl2ShdslSpanConfLineProbeEnable could have a negative effect on selecting the optimum rate or power level based on current line conditions.
未经授权更改HDSL2SHDSLSPANCLINEPROBEENABLE可能会对根据当前线路条件选择最佳速率或功率水平产生负面影响。
Unauthorized changes to row status could result in unwanted profiles being created or brought into service. Also, changes to the row status could result in profiles being inadvertently deleted or taken out of service.
未经授权更改行状态可能会导致创建或使用不需要的配置文件。此外，对行状态的更改可能会导致配置文件被无意中删除或停止使用。
o hdsl2ShdslEndpointAlarmConfProfileTable
o HDSL2SHDSLendPointAlarmConfProfile表
The table consists of the following objects that support SET operations:
该表由以下支持集合操作的对象组成：
* hdsl2ShdslEndpointThreshLoopAttenuation * hdsl2ShdslEndpointThreshSNRMargin * hdsl2ShdslEndpointThreshES * hdsl2ShdslEndpointThreshSES
* HDSL2SHDSLendPointThreshLoop衰减*hdsl2ShdslEndpointThreshSNRMargin*hdsl2ShdslEndpointThreshES*hdsl2ShdslEndpointThreshES
* hdsl2ShdslEndpointThreshCRCanomalies * hdsl2ShdslEndpointThreshLOSWS * hdsl2ShdslEndpointThreshUAS * hdsl2ShdslEndpointAlarmConfProfileRowStatus
* hdsl2ShdslEndpointThreshCRCanomalies*hdsl2ShdslEndpointThreshLOSWS*hdsl2ShdslEndpointThreshUAS*hdsl2ShdslEndpointAlarmConfProfileRowStatus
Increasing any of the threshold values could result in a notification being suppressed or deferred. Setting a threshold to 0 could result in a notification being suppressed. Suppressing or deferring a notification could prevent the timely delivery of important diagnostic information. Decreasing any of the threshold values could result in a notification being sent from the network falsely reporting a threshold crossing.
增加任何阈值都可能导致通知被抑制或延迟。将阈值设置为0可能会导致通知被抑制。禁止或推迟通知可能会妨碍重要诊断信息的及时传递。降低任何阈值都可能导致从网络发送的通知错误地报告阈值交叉。
Changing a threshold value could also have an impact on the amount of notifications the agent sends. This document adds a paragraph, which was not in RFC 3276 [RFC3276], to the Notifications section that provides general guidance to the rate limiting of notifications. Agent implementations not adhering to the rate-limiting desires could result in notifications being generated at an uncontrolled rate. Unauthorized changes to a threshold value could result in an undesired notification rate.
更改阈值也可能会影响代理发送的通知量。本文件在通知部分添加了RFC 3276[RFC3276]中没有的段落，该段落为通知的速率限制提供了一般指导。不遵守速率限制要求的代理实现可能导致以不受控制的速率生成通知。未经授权更改阈值可能会导致意外的通知率。
Unauthorized changes to row status could result in unwanted profiles being created or brought into service. Also, changes to the row status could result in profiles being inadvertently deleted or taken out of service.
未经授权更改行状态可能会导致创建或使用不需要的配置文件。此外，对行状态的更改可能会导致配置文件被无意中删除或停止使用。
Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability:
在某些网络环境中，此MIB模块中的某些可读对象（即具有MAX-ACCESS而非not ACCESS的对象）可能被视为敏感或易受攻击。因此，在通过SNMP通过网络发送这些对象时，控制甚至获取和/或通知对这些对象的访问，甚至可能加密这些对象的值，这一点非常重要。以下是表和对象及其敏感度/漏洞：
o hdsl2ShdslInventoryTable
o hdsl2ShdslInventoryTable
Access to these objects would allow an intruder to obtain information about which vendor's equipment is in use on the network. Further, such information is considered sensitive in many environments for competitive reasons.
对这些对象的访问将允许入侵者获取有关网络上使用的供应商设备的信息。此外，由于竞争原因，此类信息在许多环境中被视为敏感信息。
* hdsl2ShdslInvVendorID * hdsl2ShdslInvVendorModelNumber * hdsl2ShdslInvVendorSerialNumber * hdsl2ShdslInvVendorEOCSoftwareVersion * hdsl2ShdslInvStandardVersion * hdsl2ShdslInvVendorListNumber
* hdsl2ShdslInvVendorID*hdsl2ShdslInvVendorModelNumber*hdsl2ShdslInvVendorSerialNumber*HDSL2SHDSLINVvendorOcSoftwareVersion*hdsl2ShdslInvStandardVersion*hdsl2ShdslInvVendorListNumber
* hdsl2ShdslInvVendorIssueNumber * hdsl2ShdslInvVendorSoftwareVersion * hdsl2ShdslInvEquipmentCode * hdsl2ShdslInvVendorOther * hdsl2ShdslInvTransmissionModeCapability
* HDSL2SHDSLINV供应商编号*HDSL2SHDSLINV供应商软件转换*HDSL2SHDSLI投资设备代码*HDSL2SHDSLINV供应商其他*HDSL2SHDSLINV传输模式功能
SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module.
SNMPv3之前的SNMP版本未包含足够的安全性。即使网络本身是安全的（例如通过使用IPsec），即使如此，也无法控制安全网络上的谁可以访问和获取/设置（读取/更改/创建/删除）此MIB模块中的对象。
It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], Section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy).
建议实施者考虑SNMPv3框架所提供的安全特性（参见[RCFC310]，第8节），包括对SNMPv3加密机制的完全支持（用于身份验证和隐私）。
Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them.
此外，不建议部署SNMPv3之前的SNMP版本。相反，建议部署SNMPv3并启用加密安全性。然后，客户/运营商应负责确保授予访问此MIB模块实例权限的SNMP实体已正确配置为仅授予那些拥有确实获取或设置（更改/创建/删除）对象的合法权限的主体（用户）访问对象。
The authors are deeply grateful to the authors of the ADSL LINE MIB (RFC 2662 [RFC2662]), Gregory Bathrick and Faye Ly, as much of the text and structure of this document originate in their documents.
作者非常感谢ADSL线路MIB（RFC 2662[RFC2662]）、Gregory Bathrick和Faye Ly的作者，因为本文件的大部分文本和结构源自他们的文件。
The authors are also grateful to the authors of FR MFR MIB (RFC 3020 [RFC3020]), Prayson Pate, Bob Lynch, and Kenneth Rehbehn, as the majority of the Security Considerations section was lifted from their document.
作者还感谢FR MFR MIB（RFC 3020[RFC3020]）、Prayson Pate、Bob Lynch和Kenneth Rehbehn的作者，因为大部分安全注意事项部分已从他们的文档中删除。
The authors also acknowledge the importance of the contributions and suggestions regarding interface indexing structures received from David Horton of CITR.
作者还承认了从CITR的David Horton处收到的关于接口索引结构的贡献和建议的重要性。
The authors are extremely thankful to Bert Wijnen, Randy Presuhn, and C. M. Heard for their extensive review and the many suggestions they provided.
作者非常感谢Bert Wijnen、Randy Presohn和C.M.Heard的广泛评论和他们提供的许多建议。
Other contributions were received from the following:
其他捐款来自下列机构：
Matt Beanland (Extel Communications) Philip Bergstresser (Adtran) Steve Blackwell (Centillium) Umberto Bonollo (NEC Australia) John Egan (Metalink BroadBand) Yagal Hachmon (RAD) Mark Johnson (Red Point) Sharon Mantin (Orckit) Moti Morgenstern (ECI) Raymond Murphy (Ericsson) Lee Nipper (Verilink) Randy Presuhn (BMC Software) Katy Sherman (Orckit) Mike Sneed (ECI) Jon Turney (DSL Solutions) Aron Wahl (Memotec) Bert Wijnen (Lucent) Jim Wilson (for Mindspeed) Michael Wrobel (Memotec)
Matt Beanland（Extel Communications）Philip Bergstresser（Adtran）Steve Blackwell（Centillium）Umberto Bonollo（NEC Australia）John Egan（Metalink BroadBand）Yagal Hachmon（RAD）Mark Johnson（Red Point）Sharon Mantin（Orkit）Moti Morgenstern（ECI）Raymond Murphy（Ericsson）Lee Nipper（Verilink）Randy Presohn（BMC Software）Katy Sherman（Orkit）迈克·斯内德（ECI）、乔恩·特尼（DSL解决方案）、阿隆·沃尔（Memotec）、伯特·维恩（朗讯）、吉姆·威尔逊（Mindspeed）、迈克尔·沃贝尔（Memotec）
[G.991.2] Blackwell, S., "Single-Pair High-Speed Digital Subscriber Line (SHDSL) Transceivers", ITU-T G.991.2, December 2003.
[G.991.2]Blackwell，S.，“单对高速数字用户线（SHDSL）收发器”，ITU-T G.991.22003年12月。
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2119]Bradner，S.，“RFC中用于表示需求水平的关键词”，BCP 14，RFC 2119，1997年3月。
[RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2578]McCloghrie，K.，Perkins，D.，和J.Schoenwaeld，“管理信息的结构版本2（SMIv2）”，STD 58，RFC 2578，1999年4月。
[RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999.
[RFC2579]McCloghrie，K.，Perkins，D.，和J.Schoenwaeld，“SMIv2的文本约定”，STD 58，RFC 2579，1999年4月。
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999.
[RFC2580]McCloghrie，K.，Perkins，D.，和J.Schoenwaeld，“SMIv2的一致性声明”，STD 58，RFC 25801999年4月。
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000.
[RFC2863]McCloghrie，K.和F.Kastenholz，“接口组MIB”，RFC 28632000年6月。
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks", STD 62, RFC 3411, December 2002.
[RFC3411]Harrington，D.，Presohn，R.，和B.Wijnen，“描述简单网络管理协议（SNMP）管理框架的体系结构”，STD 62，RFC 3411，2002年12月。
[RFC3593] Tesink, K., "Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals", RFC 3593, September 2003.
[RFC3593]Tesink，K.“使用基于15分钟间隔的性能历史记录的MIB模块的文本约定”，RFC 3593，2003年9月。
[T1E1.4] American National Standards Institute, "ANSI T1E1.4/2000- 006", February 2000.
[T1E1.4]美国国家标准协会，“ANSI T1E1.4/2000-006”，2000年2月。
[RFC2662] Bathrick, G. and F. Ly, "Definitions of Managed Objects for the ADSL Lines", RFC 2662, August 1999.
[RFC2662]Bathrick，G.和F.Ly，“ADSL线路管理对象的定义”，RFC 2662，1999年8月。
[RFC3020] Pate, P., Lynch, B., and K. Rehbehn, "Definitions of Managed Objects for Monitoring and Controlling the UNI/NNI Multilink Frame Relay Function", RFC 3020, December 2000.
[RFC3020]Pate，P.，Lynch，B.和K.Rehbehn，“用于监视和控制UNI/NNI多链路帧中继功能的受管对象的定义”，RFC 3020，2000年12月。
[RFC3276] Ray, B. and R. Abbi, "Definitions of Managed Objects for High Bit-Rate DSL - 2nd generation (HDSL2) and Single-Pair High-Speed Digital Subscriber Line (SHDSL) Lines Processing", RFC 3276, May 2002.
[RFC3276]Ray，B.和R.Abbi，“高速数字用户线（DSL）的管理对象定义-第二代（HDSL2）和单对高速数字用户线（SHDSL）线路处理”，RFC 3276，2002年5月。
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, December 2002.
[RFC3410]Case，J.，Mundy，R.，Partain，D.，和B.Stewart，“互联网标准管理框架的介绍和适用性声明”，RFC 34102002年12月。
[RFC3418] Presuhn, R., "Management Information Base (MIB) for the Simple Network Management Protocol (SNMP)", STD 62, RFC 3418, December 2002.
[RFC3418]Presohn，R.，“简单网络管理协议（SNMP）的管理信息库（MIB）”，STD 62，RFC 3418，2002年12月。
Authors' Addresses
作者地址
Clay Sikes Zhone Technologies, Inc. Florida Design Center 8454 126th Ave. N. Largo, FL 33773 US
Clay Sikes Zhone Technologies，Inc.佛罗里达州设计中心8454美国佛罗里达州拉戈市第126大道，邮编33773
Phone: +1 727 530 8257
Fax: +1 727 532 5698
EMail: csikes@zhone.com
Phone: +1 727 530 8257
Fax: +1 727 532 5698
EMail: csikes@zhone.com
Bob Ray PESA Switching Systems, Inc. 330-A Wynn Drive Huntsville, AL 35805 US
Bob Ray PESA Switching Systems，Inc.美国阿拉巴马州亨茨维尔市永利大道330-A号，邮编35805
Phone: +1 256 726 9200 ext. 142
Fax: +1 256 726 9271
EMail: rray@pesa.com
Phone: +1 256 726 9200 ext. 142
Fax: +1 256 726 9271
EMail: rray@pesa.com
Rajesh Abbi Alcatel USA 2301 Sugar Bush Road Raleigh, NC 27612 US
Rajesh Abbi Alcatel USA美国北卡罗来纳州罗利糖布什路2301号，邮编：27612
Phone: +1 919-850-6194
Fax: +1 919-850-6670
EMail: Rajesh.Abbi@alcatel.com
Phone: +1 919-850-6194
Fax: +1 919-850-6670
EMail: Rajesh.Abbi@alcatel.com
Full Copyright Statement
完整版权声明
Copyright (C) The Internet Society (2005).
版权所有（C）互联网协会（2005年）。
This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights.
本文件受BCP 78中包含的权利、许可和限制的约束，除其中规定外，作者保留其所有权利。
This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
本文件及其包含的信息是按“原样”提供的，贡献者、他/她所代表或赞助的组织（如有）、互联网协会和互联网工程任务组不承担任何明示或暗示的担保，包括但不限于任何保证，即使用本文中的信息不会侵犯任何权利，或对适销性或特定用途适用性的任何默示保证。
Intellectual Property
知识产权
The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79.
IETF对可能声称与本文件所述技术的实施或使用有关的任何知识产权或其他权利的有效性或范围，或此类权利下的任何许可可能或可能不可用的程度，不采取任何立场；它也不表示它已作出任何独立努力来确定任何此类权利。有关RFC文件中权利的程序信息，请参见BCP 78和BCP 79。
Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr.
向IETF秘书处披露的知识产权副本和任何许可证保证，或本规范实施者或用户试图获得使用此类专有权利的一般许可证或许可的结果，可从IETF在线知识产权存储库获取，网址为http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org.
IETF邀请任何相关方提请其注意任何版权、专利或专利申请，或其他可能涵盖实施本标准所需技术的专有权利。请将信息发送至IETF的IETF-ipr@ietf.org.
Acknowledgement
确认
Funding for the RFC Editor function is currently provided by the Internet Society.
RFC编辑功能的资金目前由互联网协会提供。