Network Working Group B. Ray
Request for Comments: 3276 PESA Switching Systems
Category: Standards Track R. Abbi
Alcatel
May 2002
Network Working Group B. Ray
Request for Comments: 3276 PESA Switching Systems
Category: Standards Track R. Abbi
Alcatel
May 2002
Definitions of Managed Objects for High Bit-Rate DSL - 2nd generation (HDSL2) and Single-Pair High-Speed Digital Subscriber Line (SHDSL) Lines
高比特率DSL-第二代（HDSL2）和单对高速数字用户线（SHDSL）线路的受管对象定义
Status of this Memo
本备忘录的状况
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
本文件规定了互联网社区的互联网标准跟踪协议，并要求进行讨论和提出改进建议。有关本协议的标准化状态和状态，请参考当前版本的“互联网官方协议标准”（STD 1）。本备忘录的分发不受限制。
Copyright Notice
版权公告
Copyright (C) The Internet Society (2002). All Rights Reserved.
版权所有（C）互联网协会（2002年）。版权所有。
Abstract
摘要
This document defines a portion of the Management Information Base (MIB) module for use with network management protocols in the Internet community. In particular, it describes objects used for managing High Bit-Rate DSL - 2nd generation (HDSL2) and Single-Pair High-Speed Digital Subscriber Line (SHDSL) interfaces.
本文档定义了管理信息库（MIB）模块的一部分，用于Internet社区中的网络管理协议。特别是，它描述了用于管理第二代高速数字用户线（HDSL2）和单对高速数字用户线（SHDSL）接口的对象。
Table of Contents
目录
1. Introduction ............................................. 2
2. The SNMP Network Management Framework .................... 2
3. Introduction ............................................. 3
3.1 Relationship of the HDSL2/SHDSL Line MIB to other MIBs ... 3
3.2 IANA Considerations ...................................... 5
4. Conventions used in the MIB .............................. 5
4.1 Naming Conventions ....................................... 5
4.2 Textual Conventions ...................................... 6
4.3 Structure ................................................ 7
4.4 Counters, Interval Buckets and Thresholds ................ 10
4.5 Profiles ................................................. 11
4.6 Notifications ............................................ 12
5. Conformance and Compliance ............................... 14
6. Definitions .............................................. 14
7. Security Considerations .................................. 60
1. Introduction ............................................. 2
2. The SNMP Network Management Framework .................... 2
3. Introduction ............................................. 3
3.1 Relationship of the HDSL2/SHDSL Line MIB to other MIBs ... 3
3.2 IANA Considerations ...................................... 5
4. Conventions used in the MIB .............................. 5
4.1 Naming Conventions ....................................... 5
4.2 Textual Conventions ...................................... 6
4.3 Structure ................................................ 7
4.4 Counters, Interval Buckets and Thresholds ................ 10
4.5 Profiles ................................................. 11
4.6 Notifications ............................................ 12
5. Conformance and Compliance ............................... 14
6. Definitions .............................................. 14
7. Security Considerations .................................. 60
8. Acknowledgments .......................................... 62
9. References ............................................... 63
10. Intellectual Property Notice ............................. 65
11. Authors' Addresses ....................................... 65
12. Full Copyright Statement ................................. 66
8. Acknowledgments .......................................... 62
9. References ............................................... 63
10. Intellectual Property Notice ............................. 65
11. Authors' Addresses ....................................... 65
12. Full Copyright Statement ................................. 66
This document defines a portion of the Management Information Base (MIB) module for use with network management protocols in the Internet community. In particular, it describes objects used for managing High Bit-Rate DSL - 2nd generation (HDSL2) [18] and Single-Pair High-Speed Digital Subscriber Line (SHDSL) interfaces [19].
本文档定义了管理信息库（MIB）模块的一部分，用于Internet社区中的网络管理协议。特别是，它描述了用于管理高速DSL-第二代（HDSL2）[18]和单对高速数字用户线（SHDSL）接口[19]的对象。
The SNMP Management Framework presently consists of five major components:
SNMP管理框架目前由五个主要组件组成：
o An overall architecture, described in RFC 2571 [1].
o RFC 2571[1]中描述的总体架构。
o Mechanisms for describing and naming objects and events for the purpose of management. The first version of this Structure of Management Information (SMI) is called SMIv1 and is described in STD 16, RFC 1155 [2], STD 16, RFC 1212 [3], and RFC 1215 [4]. The second version, called SMIv2, is described in STD 58, RFC 2578 [5], RFC 2579 [6], and RFC 2580 [7].
o 为管理目的描述和命名对象和事件的机制。这种管理信息结构（SMI）的第一个版本称为SMIv1，在STD 16、RFC 1155[2]、STD 16、RFC 1212[3]和RFC 1215[4]中进行了描述。第二个版本称为SMIv2，在STD 58、RFC 2578[5]、RFC 2579[6]和RFC 2580[7]中进行了描述。
o Message protocols for transferring management information. The first version of the SNMP message protocol is called SNMPv1 and is described in STD 15, RFC 1157 [8]. A second version of the SNMP message protocol, which is not an Internet standards track protocol, is called SNMPv2c and described is in RFC 1901 [9] and RFC 1906 [10]. The third version of the message protocol is called SNMPv3 and is described in RFC 1906 [10], RFC 2572 [11], and RFC 2574 [12].
o 用于传输管理信息的消息协议。SNMP消息协议的第一个版本称为SNMPv1，在STD 15、RFC 1157[8]中进行了描述。SNMP消息协议的第二个版本不是互联网标准跟踪协议，称为SNMPv2c，RFC 1901[9]和RFC 1906[10]对此进行了描述。消息协议的第三个版本称为SNMPv3，在RFC 1906[10]、RFC 2572[11]和RFC 2574[12]中进行了描述。
o Protocol operations for accessing management information. The first set of protocol operations and associated PDU formats is described in STD 15, RFC 1157 [8]. A second set of protocol operations and associated PDU formats is described in RFC 1905 [13].
o 访问管理信息的协议操作。STD 15、RFC 1157[8]中描述了第一组协议操作和相关PDU格式。RFC 1905[13]中描述了第二组协议操作和相关PDU格式。
o A set of fundamental applications described in RFC 2573 [14] and the view-based access control mechanism described in RFC 2575 [15].
o RFC 2573[14]中描述的一组基本应用程序和RFC 2575[15]中描述的基于视图的访问控制机制。
A more detailed introduction to the current SNMP Management Framework can be found in RFC 2570 [16].
有关当前SNMP管理框架的更详细介绍，请参见RFC 2570[16]。
Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the mechanisms defined in the SMI.
托管对象通过虚拟信息存储（称为管理信息库或MIB）进行访问。MIB中的对象是使用SMI中定义的机制定义的。
This memo specifies a MIB module that is compliant to the SMIv2. A MIB conforming to the SMIv1 can be produced through the appropriate translations. The resulting translated MIB must be semantically equivalent, except where objects or events are omitted because no translation is possible (use of Counter64). Some machine readable information in SMIv2 will be converted into textual descriptions in SMIv1 during the translation process. However, this loss of machine readable information is not considered to change the semantics of the MIB.
此备忘录指定了符合SMIv2的MIB模块。通过适当的翻译，可以生成符合SMIv1的MIB。生成的已翻译MIB必须在语义上等效，除非由于无法翻译而省略了对象或事件（使用计数器64）。在翻译过程中，SMIv2中的一些机器可读信息将转换为SMIv1中的文本描述。但是，这种机器可读信息的丢失不被认为会改变MIB的语义。
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [17].
本文件中的关键词“必须”、“不得”、“要求”、“应”、“不应”、“应”、“不应”、“建议”、“可”和“可选”应按照RFC 2119[17]中所述进行解释。
This document describes an SNMP MIB for managing HDSL2/SHDSL Lines. These definitions are based upon the specifications for the HDSL2 and SHDSL Embedded Operations Channel (EOC) as defined in ANSI T1E1.4/2000-006 [18] and ITU G.991.2 [19].
本文档描述了用于管理HDSL2/SHDSL线路的SNMP MIB。这些定义基于ANSI T1E1.4/2000-006[18]和ITU G.991.2[19]中定义的HDSL2和SHDSL嵌入式操作通道（EOC）规范。
The MIB is located in the MIB tree under MIB 2 transmission, as discussed in the MIB-2 Integration (RFC 1213 [20] and RFC 2863 [21]) section of this document.
MIB位于MIB 2传输下的MIB树中，如本文件MIB-2集成（RFC 1213[20]和RFC 2863[21]）一节所述。
This section outlines the relationship of this MIB with other MIBs described in RFCs. Specifically, IF-MIB as presented in RFC 2863 [21] is discussed.
本节概述此MIB与RFCs中描述的其他MIB的关系。具体地说，将讨论RFC 2863[21]中提出的IF-MIB。
The HDSL2/SHDSL Line MIB specifies the detailed attributes of a data interface. As such, it needs to integrate with RFC 2863 [21]. The IANA has assigned the following ifTypes to HDSL2 and SHDSL:
HDSL2/SHDSL行MIB指定数据接口的详细属性。因此，它需要与RFC 2863集成[21]。IANA已将以下IFTYPE分配给HDSL2和SHDSL：
IANAifType ::= TEXTUAL-CONVENTION
...
SYNTAX INTEGER {
...
hdsl2 (168), -- High Bit-Rate DSL, 2nd generation
shdsl (169), -- Multirate HDSL2
...
}
IANAifType ::= TEXTUAL-CONVENTION
...
SYNTAX INTEGER {
...
hdsl2 (168), -- High Bit-Rate DSL, 2nd generation
shdsl (169), -- Multirate HDSL2
...
}
Note that the ifFixedLengthGroup from RFC 2863 [21] MUST be supported and that the ifRcvAddressGroup does not apply to this MIB.
请注意，必须支持RFC 2863[21]中的ifFixedLengthGroup，并且ifRcvAddressGroup不适用于此MIB。
The MIB branch identified by this ifType contains tables appropriate for this interface type. Most such tables extend the ifEntry table, and are indexed by ifIndex. For interfaces in systems implementing this MIB, those table entries indexed by ifIndex MUST be persistent.
此ifType标识的MIB分支包含适用于此接口类型的表。大多数这样的表扩展了ifEntry表，并由ifIndex索引。对于实现此MIB的系统中的接口，ifIndex索引的那些表项必须是持久的。
The following attributes are part of the mandatory ifGeneral group in RFC 2863 [21], and are not duplicated in the HDSL2/SHDSL Line MIB.
以下属性是RFC 2863[21]中强制ifGeneral组的一部分，在HDSL2/SHDSL行MIB中不重复。
===================================================================
ifIndex Interface index.
===================================================================
ifIndex Interface index.
ifDescr See interfaces MIB [21].
ifDescr见接口MIB[21]。
ifType hdsl2(168) or shdsl(169).
ifType hdsl2（168）或shdsl（169）。
ifSpeed Set as appropriate. (This is fixed at 1552000 for HDSL2 lines)
如果速度设置合适。（HDSL2线路固定为1552000）
ifPhysAddress This object MUST have an octet string with zero length.
ifPhysAddress此对象必须具有长度为零的八位字节字符串。
ifAdminStatus See interfaces MIB [21].
ifAdminStatus见接口MIB[21]。
ifOperStatus See interfaces MIB [21].
ifOperStatus见接口MIB[21]。
ifLastChange See interfaces MIB [21].
ifLastChange见接口MIB[21]。
ifName See interfaces MIB [21].
ifName见接口MIB[21]。
ifLinkUpDownTrapEnable Default to enabled(1).
iFlinkUpDowntrap默认值为enabled（1）。
ifHighSpeed Set as appropriate. (For HDSL2 lines, this is fixed at 2)
如果高速设置合适。（对于HDSL2线路，固定为2）
ifConnectorPresent Set as appropriate.
ifConnectorPresent可根据需要进行设置。
===================================================================
Figure 1: Use of ifTable Objects
===================================================================
Figure 1: Use of ifTable Objects
The HDSL2-SHDSL-LINE-MIB module requires the allocation of a single object identifier for its MODULE-IDENTITY. The IANA has allocated this object identifier in the transmission subtree (48), defined in the SNMPv2-SMI MIB module.
HDSL2-SHDSL-LINE-MIB模块需要为其模块标识分配单个对象标识符。IANA已在SNMPv2 SMI MIB模块中定义的传输子树（48）中分配了该对象标识符。
A. xtuC refers to a central site terminal unit;
H2TU-C for HDSL2, or STU-C for SHDSL.
B. xtuR refers to a remote site terminal unit;
H2TU-R for HDSL2, or STU-R for SHDSL.
C. xtu refers to a terminal unit; either an xtuC or xtuR.
A. xtuC refers to a central site terminal unit;
H2TU-C for HDSL2, or STU-C for SHDSL.
B. xtuR refers to a remote site terminal unit;
H2TU-R for HDSL2, or STU-R for SHDSL.
C. xtu refers to a terminal unit; either an xtuC or xtuR.
D. xru refer to a regenerator unit; H2RU for HDSL2, or SRU for SHDSL. E. xU refers to any HDSL2/SHDSL unit; either an xtu or xru. F. CRC is cyclic redundancy check [19]. G. ES means errored second [19]. H. LOSW means loss of sync word [19]. I. LOSWS means LOSW seconds [19]. J. SES means severely errored second [19]. K. SNR means signal-to-noise ratio [19]. L. UAS means unavailable second [19].
D.xru指再生器装置；H2RU用于HDSL2，或SRU用于SHDSL。E.xU指任何HDSL2/SHDSL单元；xtu或xru。F.CRC是循环冗余校验[19]。G.ES表示错误秒[19]。H.LOSW表示同步字丢失[19]。I.LOSWS指LOSW秒[19]。J.SES表示严重错误的秒[19]。K.SNR表示信噪比[19]。L.UAS表示不可用秒[19]。
The following textual conventions are defined to reflect the line topology in the MIB (further discussed in the following section) and to define the behavior of the statistics to be maintained by an agent.
定义以下文本约定以反映MIB中的线路拓扑（在下一节中进一步讨论），并定义由代理维护的统计信息的行为。
o Hdsl2ShdslUnitId:
o Hdsl2ShdslUnitId：
Attributes with this syntax uniquely identify each unit in a HDSL2/SHDSL span. It mirrors the EOC addressing mechanism:
具有此语法的属性唯一标识HDSL2/SHDSL范围中的每个单元。它反映了EOC寻址机制：
xtuC(1) - CO terminal unit xtuR(2) - CPE terminal unit xru1(3) .. xru8(10) - regenerators, numbered from central office side o Hdsl2ShdslUnitSide:
xtuC（1）-CO终端装置xtuR（2）-CPE终端装置xru1（3）。。xru8（10）-再生器，从中央办公室侧到HDSL2SHDSLUNIT侧编号：
Attributes with this syntax reference the two sides of a unit:
具有此语法的属性引用单元的两侧：
networkSide(1) - N in figure 2, below
customerSide(2) - C in figure 2, below
networkSide(1) - N in figure 2, below
customerSide(2) - C in figure 2, below
o Hdsl2ShdslWirePair:
o Hdsl2ShdslWirePair：
Attributes with this syntax reference the wire-pairs connecting the units:
具有此语法的属性引用连接单元的线对：
wirePair1(1) - First pair for HDSL2/SHDSL.
wirePair1（1）-HDSL2/SHDSL的第一对。
wirePair2(2) - Optional second pair for SHDSL only.
wirePair2（2）-仅适用于SHDSL的可选第二对。
o Hdsl2ShdslTransmissionModeType:
o HDSL2SHDSLTransmissionModelType:
Attributes with this syntax specify the regional setting for a SHDSL line. Specified as a BITS construct, the two mode types are:
具有此语法的属性指定SHDSL线路的区域设置。指定为BITS结构，两种模式类型为：
region1 - ITU-T G.991.2 Annex A region2 - ITU-T G.991.2 Annex B
地区1-ITU-T G.991.2附录A地区2-ITU-T G.991.2附录B
o Hdsl2ShdslPerfCurrDayCount:
o Hdsl2ShdslPerfCurrDayCount：
Attributes with this syntax define the behavior of the 1-day (24 hour) gauges found in the MIB.
具有此语法的属性定义在MIB中找到的1天（24小时）量表的行为。
o Hdsl2Shdsl1DayIntervalCount:
o HDSL2SHDSL1日间隔计数：
Attributes with this syntax define the behavior of the 1-day (24 hour) interval counters found in the MIB.
具有此语法的属性定义在MIB中找到的1天（24小时）间隔计数器的行为。
o Hdsl2ShdslPerfTimeElapsed:
o HDSL2SHDSLPerfTimeAppeased:
Attributes with this syntax define the behavior of the elapsed time counters found in the MIB.
具有此语法的属性定义在MIB中找到的已用时间计数器的行为。
o Hdsl2ShdslPerfIntervalThreshold:
o Hdsl2ShdslPerfIntervalThreshold：
Attributes with this syntax define the behavior of the alarm thresholds found in the MIB.
具有此语法的属性定义在MIB中找到的报警阈值的行为。
o Hdsl2ShdslClockReferenceType
o Hdsl2ShdslClockReferenceType
Attributes with this syntax define the clock references for the HDSL2/SHDSL span.
具有此语法的属性定义HDSL2/SHDSL范围的时钟参考。
The MIB is structured into following MIB groups:
MIB由以下MIB组构成：
o Span Configuration Group:
o Span配置组：
This group supports MIB objects for configuring parameters for the HDSL2/SHDSL span. It contains the following table:
此组支持用于配置HDSL2/SHDSL范围参数的MIB对象。它包含下表：
- hdsl2ShdslSpanConfTable
- HDSL2SHDSLSPANConfitable
o Span Status Group:
o Span状态组：
This group supports MIB objects for retrieving span status information. It contains the following table:
此组支持用于检索范围状态信息的MIB对象。它包含下表：
- hdsl2ShdslSpanStatusTable
- HDSL2SHDSLSPANSTAUSTABLE
o Unit Inventory Group:
o 单位库存组：
This group supports MIB objects for retrieving unit inventory information about units in HDSL2/SHDSL lines via the EOC. It contains the following table:
此组支持MIB对象，用于通过EOC检索HDSL2/SHDSL线路中设备的设备库存信息。它包含下表：
- hdsl2ShdslInventoryTable
- hdsl2ShdslInventoryTable
o Segment Endpoint Configuration Group:
o 段终结点配置组：
This group supports MIB objects for configuring parameters for the HDSL2/SHDSL segment endpoints. It contains the following table:
此组支持用于为HDSL2/SHDSL段端点配置参数的MIB对象。它包含下表：
- hdsl2ShdslEndpointConfTable
- hdsl2ShdslEndpointConfTable
o Segment Endpoint Current Status/Performance Group:
o 段端点当前状态/性能组：
This group supports MIB objects that provide the current status/performance information relating to segment endpoints. It contains the following table:
此组支持提供与段端点相关的当前状态/性能信息的MIB对象。它包含下表：
- hdsl2ShdslEndpointCurrTable
- hdsl2ShdslEndpointCurrTable
o Segment Endpoint 15-Minute Interval Status/Performance Group:
o 分段终点15分钟间隔状态/性能组：
This group supports MIB objects that provide historic status/performance information relating to segment endpoints in 15- minute intervals. It contains the following table:
该组支持MIB对象，这些对象以15分钟的间隔提供与段端点相关的历史状态/性能信息。它包含下表：
- hdsl2Shdsl15MinIntervalTable
- HDSL2SHDSL15最小间隔
o Segment Endpoint 1-Day Interval Status/Performance Group:
o 分段终点1天间隔状态/绩效组：
This group supports MIB objects that provide historic status/performance information relating to segment endpoints in 1-day intervals. It contains the following table:
此组支持MIB对象，这些对象每隔1天提供与段端点相关的历史状态/性能信息。它包含下表：
- hdsl2Shdsl1DayIntervalTable
- HDSL2SHDSL1日期间隔表
o Maintenance Group:
o 维修组：
This group supports MIB objects for performing maintenance operations such as loopbacks for HDSL2/SHDSL lines. It contains the following table(s):
此组支持用于执行维护操作（如HDSL2/SHDSL线路的环回）的MIB对象。它包含下表：
- hdsl2ShdslEndpointMaintTable - hdsl2ShdslUnitMaintTable
- hdsl2ShdslEndpointMaintTable-HDSL2SHDSluntMaintTable
o Span Configuration Profile Group:
o Span配置配置文件组：
This group supports MIB objects for defining configuration profiles for HDSL2/SHDSL Spans. It contains the following table:
此组支持MIB对象，用于定义HDSL2/SHDSL范围的配置配置文件。它包含下表：
- hdsl2ShdslSpanConfProfileTable
- hdsl2ShdslSpanConfProfileTable
o Segment Endpoint Alarm Configuration Profile Group:
o 段端点报警配置配置文件组：
This group supports MIB objects for defining alarm configuration profiles for HDSL2/SHDSL Segment Endpoints. It contains the following table:
此组支持MIB对象，用于定义HDSL2/SHDSL段端点的报警配置文件。它包含下表：
- hdsl2ShdslEndpointAlarmConfProfileTable
- HDSL2SHDSLendPointAlarmConfProfile表
o Notifications Group:
o 通知组：
This group defines the notifications supported for HDSL2/SHDSL lines:
此组定义HDSL2/SHDSL线路支持的通知：
- hdsl2ShdslLoopAttenCrossing - hdsl2ShdslSNRMarginCrossing - hdsl2ShdslPerfESThresh - hdsl2ShdslPerfSESThresh - hdsl2ShdslPerfCRCanomaliesThresh - hdsl2ShdslPerfLOSWSThresh - hdsl2ShdslPerfUASThresh - hdsl2ShdslSpanInvalidNumRepeaters - hdsl2ShdslLoopbackFailure - hdsl2ShdslpowerBackoff - hdsl2ShdsldeviceFault - hdsl2ShdsldcContinuityFault - hdsl2ShdslconfigInitFailure - hdsl2ShdslprotocolInitFailure - hdsl2ShdslnoNeighborPresent - hdsl2ShdslLocalPowerLoss
- HDSL2SHDSLLoopAttentinCrossing-hdsl2ShdslSNRMarginCrossing-hdsl2ShdslPerfESThresh-hdsl2ShdslPerfESThresh-HDSL2SHDSLperfectrCanomaliesthresh-HDSL2SHDSLPerfectrLoopsThresh-HDSL2SHDSLSpanivalidNumRepeaters-hdsl2ShdslLoopbackFailure-hdsl2ShdslpowerBackoff-hdsl2ShdsldeviceFault-hdsl2ShdsldcContinuityFault-hdsl2ShdslconfigInitFailure-hdsl2ShdslprotocolInitFailure-hdsl2ShdslnoNeighborPresent-hdsl2ShdslLocalPowerLoss
An HDSL2/SHDSL Line consists of a minimum of two units - xtuC (the central termination unit) and an xtuR (the remote termination unit). The line may optionally support up to 8 repeater/regenerator units (xru) as shown in the figure below.
HDSL2/SHDSL线路至少由两个单元组成——xtuC（中央终端单元）和xtuR（远程终端单元）。该生产线可选择支持多达8个中继器/再生器单元（xru），如下图所示。
<-- Network Side Customer Side -->
<-- Network Side Customer Side -->
|</////////////////// HDSL2/SHDSL Span ////////////////////>|
|</////////////////// HDSL2/SHDSL Span ////////////////////>|
<~~~> <~~~> HDSL2/SHDSL Segments <~~~>
<~~~> <~~~> HDSL2/SHDSL Segments <~~~>
+-------+ +-------+ +-------+ +-------+ +-------+
+ C=1=N C=1=N C=..1..=N C=1=N +
| xtuC | | xru1 | | xru2 | | xru8 | | xtuR |
+ C=2=N C=2=N C=..2..=N C=2=N +
+-------+ +-------+ +-------+ +-------+ +-------+
+-------+ +-------+ +-------+ +-------+ +-------+
+ C=1=N C=1=N C=..1..=N C=1=N +
| xtuC | | xru1 | | xru2 | | xru8 | | xtuR |
+ C=2=N C=2=N C=..2..=N C=2=N +
+-------+ +-------+ +-------+ +-------+ +-------+
Key: <////> HDSL2/SHDSL Span
<~~~~> HDSL2/SHDSL Segment
=1= HDSL2/SHDSL wire-pair-1
=2= SHDSL optional wire-pair-2 (Not applicable to HDSL2)
C Customer Side Segment Endpoint (modem)
N Network Side Segment Endpoint (modem)
Key: <////> HDSL2/SHDSL Span
<~~~~> HDSL2/SHDSL Segment
=1= HDSL2/SHDSL wire-pair-1
=2= SHDSL optional wire-pair-2 (Not applicable to HDSL2)
C Customer Side Segment Endpoint (modem)
N Network Side Segment Endpoint (modem)
Figure 2: General topology for an HDSL2/SHDSL Line
图2:HDSL2/SHDSL线路的一般拓扑
For SNR Margin, Loop Attenuation, ES, SES, CRC anomalies, LOSW, and UAS, there are event counters, current 15-minute and 0 to 96 15- minute history bucket(s) of "interval-counters", as well as current and 0 to 30 previous 1-day interval-counter(s). Each current 15- minute event bucket has an associated threshold notification.
对于信噪比裕度、环路衰减、ES、SES、CRC异常、LOSW和UAS，有事件计数器、“间隔计数器”的当前15分钟和0至96 15分钟历史段，以及当前和0至30个前1天间隔计数器。每个当前的15分钟事件存储桶都有一个相关的阈值通知。
Unlike RFC 2493 [22] and RFC 2662 [23], there is no representation in the MIB for invalid buckets. In those cases where the data for an interval is suspect or known to be invalid, the agent MUST NOT report the interval. If the current 15-minute event bucket is determined to be invalid, notifications based upon the value of the event bucket MUST NOT be generated.
与RFC 2493[22]和RFC 2662[23]不同，MIB中没有无效存储桶的表示。在怀疑或已知某个时间间隔的数据无效的情况下，代理不得报告该时间间隔。如果确定当前15分钟事件存储桶无效，则不得生成基于事件存储桶值的通知。
Not reporting an interval will result in holes in the associated table. For example, the table, hdsl2Shdsl15MinIntervalTable, is indexed by { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}. If interval 12 is determined to be invalid but intervals 11 and 13 are valid, a Get Next operation on the indices .1.1.1.1.11 would return indices .1.1.1.1.13.
不报告间隔将导致关联表中出现漏洞。例如，表hdsl2Shdsl15MinIntervalTable由{ifIndex，HDSL2SHDSLINVENDINDEX，hdsl2ShdslEndpointSide，hdsl2ShdslEndpointWirePair，HDSL2SHDSL15MININTERVALTER}索引。如果确定区间12无效，但区间11和13有效，则对索引进行Get Next操作。1.1.1.1.11将返回索引。1.1.1.1.13。
There is no requirement for an agent to ensure a fixed relationship between the start of a fifteen minute interval and any wall clock; however some implementations may align the fifteen minute intervals with quarter hours. Likewise, an implementation may choose to align one day intervals with the start of a day.
不要求代理确保15分钟间隔的开始和任何挂钟之间的固定关系；但是，一些实施可能会将15分钟的间隔与四分之一小时的间隔对齐。同样，实现可以选择将一天的间隔与一天的开始对齐。
Counters are not reset when an xU is reinitialized, only when the agent is reset or reinitialized (or under specific request outside the scope of this MIB).
当重新初始化xU时，计数器不会重置，仅当代理重置或重新初始化时（或在此MIB范围之外的特定请求下）才会重置。
As a managed node can handle a large number of xUs, (e.g., hundreds or perhaps thousands of lines), provisioning every parameter on every xU may become burdensome. Moreover, most lines are provisioned identically with the same set of parameters. To simplify the provisioning process, this MIB makes use of profiles. A profile is a set of parameters that can be shared by multiple lines using the same configuration.
由于受管节点可以处理大量xU（例如，数百或数千行），因此在每个xU上配置每个参数可能会变得很麻烦。此外，大多数行使用相同的参数集进行相同的设置。为了简化资源调配过程，此MIB使用配置文件。配置文件是一组参数，可由使用相同配置的多条线路共享。
The following profiles are used in this MIB:
此MIB中使用了以下配置文件：
o Span Configuration Profiles - Span configuration profiles contain parameters for configuring HDSL2/SHDSL spans. They are defined in the hdsl2ShdslSpanConfProfileTable. Since span configuration parameters are only applicable for SHDSL, the support for span configuration profiles are optional for HDSL2 interfaces.
o Span配置文件-Span配置文件包含用于配置HDSL2/SHDSL跨距的参数。它们在HDSL2SHDSLSPANConfProfile表中定义。由于span配置参数仅适用于SHDSL，因此对span配置文件的支持对于HDSL2接口是可选的。
Note that the configuration of the span dictates the behavior for each individual segment end point in the span. If a different configuration is provisioned for any given segment end point within the span, the new configuration for this segment end point will override the span configuration for this segment end point only.
请注意，跨度的配置决定了跨度中每个单独线段端点的行为。如果为范围内的任何给定段端点提供了不同的配置，则此段端点的新配置将仅覆盖此段端点的范围配置。
o Segment Endpoint Alarm Configuration Profiles - These profiles contain parameters for configuring alarm thresholds for HDSL2/SHDSL segment endpoints. These profiles are defined in the hdsl2ShdslEndpointAlarmConfProfileTable.
o 段端点报警配置配置文件-这些配置文件包含用于配置HDSL2/SHDSL段端点报警阈值的参数。这些配置文件在HDSL2SHDSLendPointAlarmConfProfile表中定义。
The index value for this profile is a locally-unique administratively assigned name for the profile having the textual convention `SnmpAdminString' (RFC 2571 [1]).
此配置文件的索引值是具有文本约定“SnmpAdminString”（RFC 2571[1]）的配置文件的本地唯一管理分配名称。
One or more lines may be configured to share parameters of a single profile (e.g., hdsl2ShdslEndpointAlarmConfProfile = `silver') by setting its hdsl2ShdslEndpointAlarmConfProfile objects to the value of this profile. If a change is made to the profile, all lines that
通过将其hdsl2ShdslEndpointAlarmConfProfile对象设置为此配置文件的值，可以将一条或多条线路配置为共享单个配置文件的参数（例如，hdsl2ShdslEndpointAlarmConfProfile=`silver'）。如果对纵断面进行了更改，则
refer to it will be reconfigured to the changed parameters. Before a profile can be deleted or taken out of service it must be first unreferenced from all associated lines.
请参阅，它将根据更改的参数进行重新配置。在删除或停止使用配置文件之前，必须首先从所有关联行中取消引用该配置文件。
Implementations MUST provide a default profile whose name is `DEFVAL' for each profile type. The values of the associated parameters will be vendor specific unless otherwise indicated in this document. Before a line's profiles have been set, these profiles will be automatically used by setting hdsl2ShdslEndpointAlarmConfProfile and hdsl2ShdslSpanConfProfile to `DEFVAL' where appropriate. This default profile name, 'DEFVAL', is considered reserved in the context of profiles defined in this MIB.
实现必须为每种配置文件类型提供一个名为“deffal”的默认配置文件。除非本文件另有说明，否则相关参数的值将根据供应商而定。在设置线路配置文件之前，将通过将hdsl2ShdslEndpointAlarmConfProfile和hdsl2ShdslSpanConfProfile设置为“DEFVAL”（如适用），自动使用这些配置文件。此默认配置文件名“deffal”被视为在此MIB中定义的配置文件上下文中保留。
Profiles are created, assigned, and deleted dynamically using the profile name and profile row status in each of the four profile tables.
使用四个配置文件表中的配置文件名称和配置文件行状态动态创建、分配和删除配置文件。
Profile changes MUST take effect immediately. These changes MAY result in a restart (hard reset or soft restart) of the units on the line.
配置文件更改必须立即生效。这些更改可能会导致机组重新启动（硬复位或软重启）。
The ability to generate the SNMP notifications coldStart/WarmStart (per [21]) which are per agent (e.g., per Digital Subscriber Line Access Multiplexer, or DSLAM, in such a device), and linkUp/linkDown (per [21]) which are per interface (i.e., HDSL2/SHDSL line) is required.
需要能够生成每个代理（例如，在这样的设备中，每个数字用户线路接入多路复用器或DSLAM）的SNMP通知coldStart/WarmStart（per[21]），以及每个接口（即HDSL2/SHDSL线路）的链路上/链路下（per[21]）。
A linkDown notification MAY be generated whenever any of ES, SES, CRC Anomaly, LOSW, or UAS event occurs. The corresponding linkUp notification MAY be sent when all link failure conditions are cleared.
每当发生ES、SES、CRC异常、LOSW或UAS事件时，可能会生成链路关闭通知。当清除所有链路故障条件时，可能会发送相应的连接通知。
The notifications defined in this MIB are for initialization failure and for the threshold crossings associated with the following events: ES, SES, CRC Anomaly, LOSW, and UAS. Each threshold has its own enable/threshold value. When that value is 0, the notification is disabled.
此MIB中定义的通知用于初始化失败以及与以下事件相关的阈值交叉：ES、SES、CRC异常、LOSW和UAS。每个阈值都有自己的启用/阈值。当该值为0时，将禁用通知。
The hdsl2ShdslEndpointCurrStatus is a bitmask representing all outstanding error conditions associated with a particular Segment Endpoint. Note that since status of remote endpoints is obtained via the EOC, this information may be unavailable for units that are unreachable via EOC during a line error condition. Therefore, not all conditions may always be included in its current status. Notifications corresponding to the bit fields in this object are defined.
hdsl2ShdslEndpointCurrStatus是一个位掩码，表示与特定段端点相关的所有未解决错误条件。请注意，由于远程端点的状态是通过EOC获得的，因此在线路错误情况下，对于无法通过EOC访问的单元，此信息可能不可用。因此，并非所有条件都可以始终包含在其当前状态中。定义了与此对象中的位字段相对应的通知。
Two alarm conditions, SNR Margin Alarm and Loop Attenuation Alarm, are organized in a manner slightly different from that implied in the EOC specifications. In the MIB, these alarm conditions are tied to the two thresholds hdsl2ShdslEndpointThreshSNRMargin and hdsl2ShdslEndpointThreshLoopAttenuation found in the hdsl2ShdslEndpointAlarmConfProfileTable. In the EOC, the alarm conditions associated with these thresholds are per-unit. In the MIB, these alarm conditions are per-endpoint. For terminal units, this has no impact. For repeaters, this implies an implementation variance where the agent in the terminal unit is responsible for detecting a threshold crossing. As the reporting of a repeater detected alarm condition to the polling terminal unit occurs in the same EOC message as the reporting of the current SNR Margin and Loop Attenuation values, it is anticipated that this will have very little impact on agent implementation.
两种报警条件（SNR余量报警和环路衰减报警）的组织方式与EOC规范中暗示的方式略有不同。在MIB中，这些报警条件与在HDSL2SHDSLendPointAlarmConfProfile表中找到的两个阈值hdsl2ShdslEndpointThreshSNRMargin和HDSL2SHDSLendPointThreshLoopDepression相关联。在EOC中，与这些阈值相关的报警条件为每单位。在MIB中，这些报警条件是针对每个端点的。对于终端设备，这没有影响。对于中继器，这意味着实现差异，其中终端单元中的代理负责检测阈值交叉。由于向轮询终端单元报告中继器检测到的报警条件与报告当前SNR裕度和环路衰减值在同一EOC消息中发生，因此预计这对代理实现的影响很小。
A threshold notification occurs whenever the corresponding current 15-minute interval error counter becomes equal to, or exceeds the threshold value. One notification may be sent per interval per interface. Since the current 15-minute counter is reset to 0 every 15 minutes, and if the condition persists, the notification may recur as often as every 15 minutes. For example, to get a notification whenever a "loss of" event occurs (but at most once every 15 minutes), set the corresponding threshold to 1. The agent will generate a notification when the event originally occurs.
每当相应的当前15分钟间隔错误计数器等于或超过阈值时，就会出现阈值通知。每个接口的每个间隔可以发送一个通知。由于当前15分钟计数器每15分钟重置为0，并且如果该情况持续存在，则该通知可能每15分钟重复一次。例如，要在“丢失”事件发生时（但最多每15分钟一次）获取通知，请将相应的阈值设置为1。代理将在事件最初发生时生成通知。
Note that the Network Management System, or NMS, may receive a linkDown notification, as well, if enabled (via ifLinkUpDownTrapEnable [21]). At the beginning of the next 15 minute interval, the counter is reset. When the first second goes by and the event occurs, the current interval bucket will be 1, which equals the threshold, and the notification will be sent again.
请注意，如果启用，网络管理系统（或NMS）也可能会收到链路关闭通知（通过iFlinkUpDownTrappenable[21]）。在下一个15分钟间隔开始时，计数器复位。当第一秒过去并且事件发生时，当前间隔bucket将为1（等于阈值），并且将再次发送通知。
A hdsl2ShdslSpanInvalidNumRepeaters notification may be generated following completion of the discovery phase if the number of repeaters discovered on the line differs from the number of repeaters specified in hdsl2ShdslSpanConfNumRepeaters. For those conditions where the number of provisioned repeaters is greater than those encountered during span discovery, all table entries associated with the nonexistent repeaters are to be discarded. For those conditions where the number of provisioned repeaters is less than those encountered during span discovery, additional table entries are to be created using the default span configuration profile.
如果在线路上发现的中继器数量不同于hdsl2ShdslSpanConfNumRepeaters中指定的中继器数量，则在发现阶段完成后，可能会生成hdsl2ShdslSpanInvalidNumRepeaters通知。对于配置的中继器数量大于跨度发现期间遇到的中继器数量的情况，将丢弃与不存在的中继器关联的所有表项。对于已配置中继器的数量小于span发现期间遇到的数量的情况，将使用默认的span配置文件创建其他表项。
For both HDSL2 and SHDSL lines, the following group(s) are mandatory:
对于HDSL2和SHDSL线路，以下组是必需的：
hdsl2ShdslSpanConfGroup hdsl2ShdslSpanStatusGroup hdsl2ShdslInventoryGroup hdsl2ShdslEndpointConfGroup hdsl2Shdsl15MinIntervalGroup hdsl2Shdsl1DayIntervalGroup hdsl2ShdslMaintenanceGroup hdsl2ShdslEndpointAlarmConfGroup hdsl2ShdslNotificationGroup
hdsl2ShdslSpanConfGroup HDSL2SHDSLspanStatus Group hdsl2ShdslInventoryGroup hdsl2ShdslEndpointConfGroup HDSL2SHDSL15MiniIntervalGroup hdsl2Shdsl1DayIntervalGroup HDSL2SHDSLMaintenance Group hdsl2ShdslEndpointAlarmConfGroup hdsl2ShdslNotificationGroup
For HDSL2 lines, the following group(s) are optional:
对于HDSL2线路，以下组是可选的：
hdsl2ShdslSpanConfProfileGroup hdsl2ShdslSpanShdslStatusGroup
hdsl2ShdslSpanConfProfileGroup HDSL2SHDSLspanSHDSLSStatusGroup
HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGIN
HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Unsigned32, Gauge32, NOTIFICATION-TYPE, Integer32, transmission FROM SNMPv2-SMI RowStatus, TEXTUAL-CONVENTION FROM SNMPv2-TC ifIndex FROM IF-MIB PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF;
从IF-MIB PerfCurrentCount导入模块标识、对象类型、计数器32、无符号32、仪表32、通知类型、整数32、从SNMPv2 SMI RowStatus的传输、从SNMPv2 TC ifIndex导入文本约定、从IF-MIB PerfCurrentCount导入PerfIntervalCount、从PerfHist TC MIB SNMPAdminInstalling导入SNMP-FRAMEWORK-MIB MODULE-COMPLIANCE、对象组、，来自SNMPv2 CONF的通知组；
hdsl2ShdslMIB MODULE-IDENTITY
LAST-UPDATED "200205090000Z" -- May 9, 2002
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed
hdsl2ShdslMIB MODULE-IDENTITY
LAST-UPDATED "200205090000Z" -- May 9, 2002
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed
Postal: P.O. Box 37324 Raleigh NC 27627-7324 Email: sneedmike@hotmail.com
邮寄：罗利北卡罗来纳州罗利37324信箱27627-7324电子邮件：sneedmike@hotmail.com
Co-editor: Bob Ray PESA Switching Systems, Inc. Postal: 330-A Wynn Drive Huntsville, AL 35805 USA Email: rray@pesa.com Phone: +1 256 726 9200 ext. 142
合编：Bob Ray PESA Switching Systems，Inc.邮政编码：330-A美国阿拉巴马州亨茨维尔永利大道A号邮编：35805电子邮件：rray@pesa.com电话：+12567269200分机142
Co-editor: Rajesh Abbi Alcatel USA Postal: 2912 Wake Forest Road Raleigh, NC 27609-7860 USA
合编：Rajesh Abbi Alcatel美国邮政：美国北卡罗来纳州罗利维克森林路2912号，邮编：27609-7860
Email: Rajesh.Abbi@alcatel.com Phone: +1 919 850 6194 "
电子邮件：Rajesh。Abbi@alcatel.com电话：+1 919 850 6194“
DESCRIPTION "This MIB module defines a collection of objects for managing HDSL2/SHDSL lines. An agent may reside at either end of the line, however the MIB is designed to require no management communication between the modems beyond that inherent in the low-level EOC line protocol as defined in ANSI T1E1.4/2000-006 (for HDSL2 lines), or in ITU G.991.2 (for SHDSL lines)." REVISION "200205090000Z" -- May 9, 2002 DESCRIPTION "Initial version, published as RFC 3276."
DESCRIPTION“此MIB模块定义了一组用于管理HDSL2/SHDSL线路的对象。一个代理可以驻留在线路的任意一端，但是MIB设计为不需要调制解调器之间的管理通信，除了ANSI T1E1.4/2000-006（用于HDSL2线路）中定义的低级EOC线路协议中固有的通信之外，或ITU G.991.2（适用于SHDSL线路）。“修订版”200205090000Z--2002年5月9日描述“初始版本，发布为RFC 3276。”
::= { transmission 48 }
::= { transmission 48 }
hdsl2ShdslMibObjects OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 1 }
hdsl2ShdslMibObjects OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 1 }
-- Textual Conventions used in this MIB --
--此MIB中使用的文本约定--
Hdsl2ShdslPerfCurrDayCount ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A gauge associated with interface performance measurements in
a current 1-day (24 hour) measurement interval.
Hdsl2ShdslPerfCurrDayCount ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A gauge associated with interface performance measurements in
a current 1-day (24 hour) measurement interval.
The value of this gauge starts at zero at the beginning of an interval and is increased when associated events occur, until the end of the 1-day interval. At that time the value of the gauge is stored in the previous 1-day history interval, as defined in a companion object of type
该仪表的值在间隔开始时从零开始，并在相关事件发生时增加，直到1天间隔结束。此时，仪表值存储在前一个1天的历史间隔中，如类型的伴随对象中所定义
Hdsl2Shdsl1DayIntevalCount, and the current interval gauge is restarted at zero.
Hdsl2Shdsl1DayIntevalCount，当前间隔计在零处重新启动。
In the case where the agent has no valid data available for this interval the corresponding object instance is not available and upon a retrieval request a corresponding error message shall be returned to indicate that this instance does not exist. Please note that zero is a valid value." SYNTAX Gauge32
如果代理在此时间间隔内没有可用的有效数据，则相应的对象实例不可用，并且在检索请求时，应返回相应的错误消息以指示此实例不存在。请注意，零是一个有效值
Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A counter associated with interface performance measurements
during the most previous 1-day (24 hour) measurement interval.
The value of this gauge is equal to the value of the current
day gauge, as defined in a companion object of type
Hdsl2ShdslPerfCurrDayCount, at the end of its most recent
interval.
Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A counter associated with interface performance measurements
during the most previous 1-day (24 hour) measurement interval.
The value of this gauge is equal to the value of the current
day gauge, as defined in a companion object of type
Hdsl2ShdslPerfCurrDayCount, at the end of its most recent
interval.
In the case where the agent has no valid data available for this interval the corresponding object instance is not available and upon a retrieval request a corresponding error message shall be returned to indicate that this instance does not exist." SYNTAX Gauge32
如果代理在此时间间隔内没有可用的有效数据，则相应的对象实例不可用，并且在检索请求时，应返回相应的错误消息以指示此实例不存在。”语法表32
Hdsl2ShdslPerfTimeElapsed ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as
an adjustment in the system's time-of-day clock or the addition
of a leap second, the current interval exceeds the maximum
value, the agent will return the maximum value.
Hdsl2ShdslPerfTimeElapsed ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as
an adjustment in the system's time-of-day clock or the addition
of a leap second, the current interval exceeds the maximum
value, the agent will return the maximum value.
For 15 minute intervals, the range is limited to (0..899). For 24 hour intervals, the range is limited to (0..86399)." SYNTAX Unsigned32(0..86399)
对于15分钟的间隔，范围限制为（0..899）。对于24小时间隔，范围限制为（0..86399）。“语法无符号32（0..86399）
Hdsl2ShdslPerfIntervalThreshold ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This convention defines a range of values that may be set in
a fault threshold alarm control. As the number of seconds in
a 15-minute interval numbers at most 900, objects of this type
may have a range of 0...900, where the value of 0 disables the
alarm."
Hdsl2ShdslPerfIntervalThreshold ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This convention defines a range of values that may be set in
a fault threshold alarm control. As the number of seconds in
a 15-minute interval numbers at most 900, objects of this type
may have a range of 0...900, where the value of 0 disables the
alarm."
SYNTAX Unsigned32(0..900)
语法Unsigned32（0..900）
Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the unique identification for all units in a
HDSL2/SHDSL Span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
SYNTAX INTEGER
{
xtuC(1),
xtuR(2),
xru1(3),
xru2(4),
xru3(5),
xru4(6),
xru5(7),
xru6(8),
xru7(9),
xru8(10)
}
Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the unique identification for all units in a
HDSL2/SHDSL Span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
SYNTAX INTEGER
{
xtuC(1),
xtuR(2),
xru1(3),
xru2(4),
xru3(5),
xru4(6),
xru5(7),
xru6(8),
xru7(9),
xru8(10)
}
Hdsl2ShdslUnitSide ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the referenced side of a HDSL2/SHDSL unit - Network
or Customer side. The side facing the Network is the Network
side, while the side facing the Customer is the Customer side."
SYNTAX INTEGER
{
networkSide(1),
customerSide(2)
}
Hdsl2ShdslUnitSide ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the referenced side of a HDSL2/SHDSL unit - Network
or Customer side. The side facing the Network is the Network
side, while the side facing the Customer is the Customer side."
SYNTAX INTEGER
{
networkSide(1),
customerSide(2)
}
Hdsl2ShdslWirePair ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the referenced pair of wires in a HDSL2/SHDSL Segment.
HDSL2 only supports a single pair (wirePair1), while SHDSL
supports an optional second pair (wirePair2)."
SYNTAX INTEGER
{
wirePair1(1),
wirePair2(2)
}
Hdsl2ShdslWirePair ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the referenced pair of wires in a HDSL2/SHDSL Segment.
HDSL2 only supports a single pair (wirePair1), while SHDSL
supports an optional second pair (wirePair2)."
SYNTAX INTEGER
{
wirePair1(1),
wirePair2(2)
}
Hdsl2ShdslTransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current
Hdsl2ShdslTransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION "Contains the regional setting of the HDSL2/SHDSL span, represented as a bit-map of possible settings. The various bit positions are:
DESCRIPTION“包含HDSL2/SHDSL范围的区域设置，表示为可能设置的位图。各种位位置包括：
Bit Meaning Description
1 region 1 Indicates ITU-T G.991.2 Annex A.
2 region 2 Indicates ITU-T G.991.2 Annex B."
SYNTAX BITS
{
region1(0),
region2(1)
}
Bit Meaning Description
1 region 1 Indicates ITU-T G.991.2 Annex A.
2 region 2 Indicates ITU-T G.991.2 Annex B."
SYNTAX BITS
{
region1(0),
region2(1)
}
Hdsl2ShdslClockReferenceType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The various STU-C symbol clock references for the
HDSL2/SHDSL span, represented as an enumeration."
SYNTAX INTEGER
{
localClk(1), -- Mode-1 per G991.2
networkClk(2), -- Mode-2 per G991.2
dataOrNetworkClk(3), -- Mode-3a per G991.2
dataClk(4) -- Mode-3b per G991.2
}
Hdsl2ShdslClockReferenceType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The various STU-C symbol clock references for the
HDSL2/SHDSL span, represented as an enumeration."
SYNTAX INTEGER
{
localClk(1), -- Mode-1 per G991.2
networkClk(2), -- Mode-2 per G991.2
dataOrNetworkClk(3), -- Mode-3a per G991.2
dataClk(4) -- Mode-3b per G991.2
}
-- Span Configuration Group --
--跨配置组--
hdsl2ShdslSpanConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports overall configuration of HDSL2/SHDSL
Spans. Entries in this table MUST be maintained in a
persistent manner."
::= { hdsl2ShdslMibObjects 1 }
hdsl2ShdslSpanConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports overall configuration of HDSL2/SHDSL
Spans. Entries in this table MUST be maintained in a
persistent manner."
::= { hdsl2ShdslMibObjects 1 }
hdsl2ShdslSpanConfEntry OBJECT-TYPE SYNTAX Hdsl2ShdslSpanConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the hdsl2ShdslSpanConfTable. Each entry represents the complete Span in a single HDSL2/SHDSL line. It is indexed by the ifIndex of the associated HDSL2/SHDSL
HDSL2SHDSLSpanCentry对象类型语法HDSL2SHDSLSpanCentry MAX-ACCESS not accessible STATUS current DESCRIPTION“HDSL2SHDSLSpanConfitable中的一个条目。每个条目表示单个HDSL2/SHDSL行中的完整跨距。它由关联HDSL2/SHDSL的ifIndex索引
line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanConfTable 1 }
line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanConfTable 1 }
Hdsl2ShdslSpanConfEntry ::=
SEQUENCE
{
hdsl2ShdslSpanConfNumRepeaters Unsigned32,
hdsl2ShdslSpanConfProfile SnmpAdminString,
hdsl2ShdslSpanConfAlarmProfile SnmpAdminString
}
Hdsl2ShdslSpanConfEntry ::=
SEQUENCE
{
hdsl2ShdslSpanConfNumRepeaters Unsigned32,
hdsl2ShdslSpanConfProfile SnmpAdminString,
hdsl2ShdslSpanConfAlarmProfile SnmpAdminString
}
hdsl2ShdslSpanConfNumRepeaters OBJECT-TYPE
SYNTAX Unsigned32(0..8)
UNITS "repeaters"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object provisions the number of repeaters/regenerators
in this HDSL2/SHDSL Span."
::= { hdsl2ShdslSpanConfEntry 1 }
hdsl2ShdslSpanConfNumRepeaters OBJECT-TYPE
SYNTAX Unsigned32(0..8)
UNITS "repeaters"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object provisions the number of repeaters/regenerators
in this HDSL2/SHDSL Span."
::= { hdsl2ShdslSpanConfEntry 1 }
hdsl2ShdslSpanConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is a pointer to a span configuration profile in the hdsl2ShdslSpanConfProfileTable, which applies to this span. The value of this object is the index of the referenced profile in the hdsl2ShdslSpanConfProfileTable. Note that span configuration profiles are only applicable to SHDSL lines.
hdsl2ShdslSpanConfProfile对象类型语法snmpadmin字符串（大小（1..32））MAX-ACCESS读写状态当前说明“此对象是指向适用于此范围的HDSL2SHDSLSpanConfProfile表中的范围配置配置文件的指针。此对象的值是HDSL2SHDSLSPANConfProfile表中引用的配置文件的索引。请注意，span配置文件仅适用于SHDSL线路。
HDSL2 lines MUST reference the default profile, 'DEFVAL'. By default, this object will have the value 'DEFVAL' (the index of the default profile).
HDSL2行必须引用默认配置文件“DEFVAL”。默认情况下，此对象的值为“deffal”（默认配置文件的索引）。
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslSpanConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 2 }
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslSpanConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 2 }
hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is a pointer to an Alarm configuration profile in
hdsl2ShdslSpanConfAlarmProfile对象类型语法SnmpAdminString（大小（1..32））MAX-ACCESS读写状态当前描述“此对象是指向
the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this object is the index of the referenced profile in the hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold configuration in the referenced profile will be used by default for all segment endpoints in this span. Individual endpoints may override this profile by explicitly specifying some other profile in the hdsl2ShdslEndpointConfTable. By default, this object will have the value 'DEFVAL' (the index of the default profile).
HDSL2SHDSLendPointAlarmConfProfile表。此对象的值是HDSL2SHDSLendPointAlarmConfProfile表中引用的配置文件的索引。默认情况下，引用配置文件中的报警阈值配置将用于此范围内的所有段端点。各个端点可以通过在hdsl2ShdslEndpointConfTable中显式指定某些其他配置文件来覆盖此配置文件。默认情况下，此对象的值为“deffal”（默认配置文件的索引）。
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 3 }
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 3 }
-- Span Status Group --
--Span状态组--
hdsl2ShdslSpanStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides overall status information of
HDSL2/SHDSL spans. This table contains live data from
equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 2 }
hdsl2ShdslSpanStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides overall status information of
HDSL2/SHDSL spans. This table contains live data from
equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 2 }
hdsl2ShdslSpanStatusEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslSpanStatusTable. Each entry
represents the complete span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL
line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanStatusTable 1 }
hdsl2ShdslSpanStatusEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslSpanStatusTable. Each entry
represents the complete span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL
line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanStatusTable 1 }
Hdsl2ShdslSpanStatusEntry ::=
SEQUENCE
{
hdsl2ShdslStatusNumAvailRepeaters Unsigned32,
hdsl2ShdslStatusMaxAttainableLineRate Unsigned32,
hdsl2ShdslStatusActualLineRate Unsigned32,
hdsl2ShdslStatusTransmissionModeCurrent
Hdsl2ShdslTransmissionModeType
Hdsl2ShdslSpanStatusEntry ::=
SEQUENCE
{
hdsl2ShdslStatusNumAvailRepeaters Unsigned32,
hdsl2ShdslStatusMaxAttainableLineRate Unsigned32,
hdsl2ShdslStatusActualLineRate Unsigned32,
hdsl2ShdslStatusTransmissionModeCurrent
Hdsl2ShdslTransmissionModeType
}
}
hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE
SYNTAX Unsigned32(0..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual number of repeaters/regenerators
discovered in this HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 1 }
hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE
SYNTAX Unsigned32(0..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual number of repeaters/regenerators
discovered in this HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 1 }
hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4112000)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the maximum attainable line rate in this HDSL2/SHDSL
span. This object provides the maximum rate the line is
capable of achieving. This is based upon measurements made
during line probing."
::= { hdsl2ShdslSpanStatusEntry 2 }
hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4112000)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the maximum attainable line rate in this HDSL2/SHDSL
span. This object provides the maximum rate the line is
capable of achieving. This is based upon measurements made
during line probing."
::= { hdsl2ShdslSpanStatusEntry 2 }
hdsl2ShdslStatusActualLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4112000)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual line rate in this HDSL2/SHDSL span. This
should equal ifSpeed."
::= { hdsl2ShdslSpanStatusEntry 3 }
hdsl2ShdslStatusActualLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4112000)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual line rate in this HDSL2/SHDSL span. This
should equal ifSpeed."
::= { hdsl2ShdslSpanStatusEntry 3 }
hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the current Power Spectral Density (PSD) regional
setting of the HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 4 }
hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the current Power Spectral Density (PSD) regional
setting of the HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 4 }
-- Unit Inventory Group --
--单位库存组--
hdsl2ShdslInventoryTable OBJECT-TYPE SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntry MAX-ACCESS not-accessible
Hdsl2ShdslInventoryEntry MAX-ACCESS的hdsl2ShdslInventoryTable对象类型语法序列不可访问
STATUS current DESCRIPTION "This table supports retrieval of unit inventory information available via the EOC from units in a HDSL2/SHDSL line.
STATUS current DESCRIPTION“此表支持从HDSL2/SHDSL线路中的单元检索通过EOC可用的单元库存信息。
Entries in this table are dynamically created during the line discovery process. The life cycle for these entries is as follows:
此表中的条目是在行发现过程中动态创建的。这些条目的生命周期如下所示：
- xtu discovers a device, either a far-end xtu or an xru - an inventory table entry is created for the device - the line goes down for whatever reason - inventory table entries for unreachable devices are destroyed.
- xtu发现一个设备，无论是远端xtu还是xru—为该设备创建了一个清单表条目—无论出于何种原因，该行都会中断—无法访问的设备的清单表条目会被销毁。
As these entries are created/destroyed dynamically, they
are NOT persistent."
::= { hdsl2ShdslMibObjects 3 }
As these entries are created/destroyed dynamically, they
are NOT persistent."
::= { hdsl2ShdslMibObjects 3 }
hdsl2ShdslInventoryEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslInventoryTable. Each entry
represents inventory information for a single unit in a
HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslInventoryTable 1 }
hdsl2ShdslInventoryEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslInventoryTable. Each entry
represents inventory information for a single unit in a
HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslInventoryTable 1 }
Hdsl2ShdslInventoryEntry ::=
SEQUENCE
{
hdsl2ShdslInvIndex Hdsl2ShdslUnitId,
hdsl2ShdslInvVendorID OCTET STRING,
hdsl2ShdslInvVendorModelNumber OCTET STRING,
hdsl2ShdslInvVendorSerialNumber OCTET STRING,
hdsl2ShdslInvVendorEOCSoftwareVersion Integer32,
hdsl2ShdslInvStandardVersion Integer32,
hdsl2ShdslInvVendorListNumber OCTET STRING,
hdsl2ShdslInvVendorIssueNumber OCTET STRING,
hdsl2ShdslInvVendorSoftwareVersion OCTET STRING,
hdsl2ShdslInvEquipmentCode OCTET STRING,
hdsl2ShdslInvVendorOther OCTET STRING,
hdsl2ShdslInvTransmissionModeCapability
Hdsl2ShdslTransmissionModeType
Hdsl2ShdslInventoryEntry ::=
SEQUENCE
{
hdsl2ShdslInvIndex Hdsl2ShdslUnitId,
hdsl2ShdslInvVendorID OCTET STRING,
hdsl2ShdslInvVendorModelNumber OCTET STRING,
hdsl2ShdslInvVendorSerialNumber OCTET STRING,
hdsl2ShdslInvVendorEOCSoftwareVersion Integer32,
hdsl2ShdslInvStandardVersion Integer32,
hdsl2ShdslInvVendorListNumber OCTET STRING,
hdsl2ShdslInvVendorIssueNumber OCTET STRING,
hdsl2ShdslInvVendorSoftwareVersion OCTET STRING,
hdsl2ShdslInvEquipmentCode OCTET STRING,
hdsl2ShdslInvVendorOther OCTET STRING,
hdsl2ShdslInvTransmissionModeCapability
Hdsl2ShdslTransmissionModeType
}
}
hdsl2ShdslInvIndex OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table corresponds to a physical element
in a HDSL2/SHDSL Span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
::= { hdsl2ShdslInventoryEntry 1 }
hdsl2ShdslInvIndex OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table corresponds to a physical element
in a HDSL2/SHDSL Span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
::= { hdsl2ShdslInventoryEntry 1 }
hdsl2ShdslInvVendorID OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor ID as reported in an Inventory Response message."
::= { hdsl2ShdslInventoryEntry 2 }
hdsl2ShdslInvVendorID OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor ID as reported in an Inventory Response message."
::= { hdsl2ShdslInventoryEntry 2 }
hdsl2ShdslInvVendorModelNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor model number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 3 }
hdsl2ShdslInvVendorModelNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor model number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 3 }
hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor serial number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 4 }
hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor serial number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 4 }
hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor EOC version as reported in a Discovery Response
message."
::= { hdsl2ShdslInventoryEntry 5 }
hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor EOC version as reported in a Discovery Response
message."
::= { hdsl2ShdslInventoryEntry 5 }
hdsl2ShdslInvStandardVersion OBJECT-TYPE
HDSL2SHDSLINVSStandardVersion对象类型
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Version of the HDSL2/SHDSL standard implemented, as reported
in an Inventory Response message."
::= { hdsl2ShdslInventoryEntry 6 }
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Version of the HDSL2/SHDSL standard implemented, as reported
in an Inventory Response message."
::= { hdsl2ShdslInventoryEntry 6 }
hdsl2ShdslInvVendorListNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(3))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor list number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 7 }
hdsl2ShdslInvVendorListNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(3))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor list number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 7 }
hdsl2ShdslInvVendorIssueNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor issue number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 8 }
hdsl2ShdslInvVendorIssueNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor issue number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 8 }
hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(6))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor software version as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 9 }
hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(6))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor software version as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 9 }
hdsl2ShdslInvEquipmentCode OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(10))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Equipment code conforming to ANSI T1.213, Coded Identification
of Equipment Entities."
::= { hdsl2ShdslInventoryEntry 10 }
hdsl2ShdslInvEquipmentCode OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(10))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Equipment code conforming to ANSI T1.213, Coded Identification
of Equipment Entities."
::= { hdsl2ShdslInventoryEntry 10 }
hdsl2ShdslInvVendorOther OBJECT-TYPE SYNTAX OCTET STRING(SIZE(12)) MAX-ACCESS read-only STATUS current
HDSL2SHDSLINVENDOR其他对象类型语法八位字节字符串（大小（12））最大访问只读状态当前
DESCRIPTION
"Other vendor information as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 11 }
DESCRIPTION
"Other vendor information as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 11 }
hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the transmission mode capability of the SHDSL unit."
::= { hdsl2ShdslInventoryEntry 12 }
hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the transmission mode capability of the SHDSL unit."
::= { hdsl2ShdslInventoryEntry 12 }
-- Segment Endpoint Configuration Group --
--段端点配置组--
hdsl2ShdslEndpointConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports configuration parameters for segment
endpoints in a HDSL2/SHDSL line. As this table is indexed
by ifIndex, it MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 4 }
hdsl2ShdslEndpointConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports configuration parameters for segment
endpoints in a HDSL2/SHDSL line. As this table is indexed
by ifIndex, it MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 4 }
hdsl2ShdslEndpointConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointConfTable. Each entry
represents a single segment endpoint in a HDSL2/SHDSL line.
It is indexed by the ifIndex of the HDSL2/SHDSL line, the
UnitId of the associated unit, the side of the unit, and the
wire-pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair}
::= { hdsl2ShdslEndpointConfTable 1 }
hdsl2ShdslEndpointConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointConfTable. Each entry
represents a single segment endpoint in a HDSL2/SHDSL line.
It is indexed by the ifIndex of the HDSL2/SHDSL line, the
UnitId of the associated unit, the side of the unit, and the
wire-pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair}
::= { hdsl2ShdslEndpointConfTable 1 }
Hdsl2ShdslEndpointConfEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide,
hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair,
hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString
}
Hdsl2ShdslEndpointConfEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide,
hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair,
hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString
}
hdsl2ShdslEndpointSide OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitSide
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The side of the unit associated with this segment endpoint -
Network/Customer side - as per the Hdsl2ShdslUnitSide textual
convention."
::= { hdsl2ShdslEndpointConfEntry 1 }
hdsl2ShdslEndpointSide OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitSide
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The side of the unit associated with this segment endpoint -
Network/Customer side - as per the Hdsl2ShdslUnitSide textual
convention."
::= { hdsl2ShdslEndpointConfEntry 1 }
hdsl2ShdslEndpointWirePair OBJECT-TYPE
SYNTAX Hdsl2ShdslWirePair
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The wire-pair of the modem associated with this segment
endpoint as per the Hdsl2ShdslWirePair textual convention."
::= { hdsl2ShdslEndpointConfEntry 2 }
hdsl2ShdslEndpointWirePair OBJECT-TYPE
SYNTAX Hdsl2ShdslWirePair
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The wire-pair of the modem associated with this segment
endpoint as per the Hdsl2ShdslWirePair textual convention."
::= { hdsl2ShdslEndpointConfEntry 2 }
hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures the alarm threshold values to be used for this segment endpoint. The values are obtained from the alarm configuration profile referenced by this object. The value of this object is the index of the referenced profile in the hdsl2ShdslEndpointAlarmConfProfileTable, or NULL (a zero-length SnmpAdminString). If the value is a zero-length SnmpAdminString, the endpoint uses the default Alarm Configuration Profile for the associated span as per the hdsl2ShdslSpanConfAlarmProfile object in the hdsl2ShdslSpanConfTable. The default value of this object is a zero-length SnmpAdminString.
hdsl2ShdslEndpointAlarmConfProfile对象类型语法SnmpAdminString（大小（0..32））最大访问读写状态当前说明“此对象配置用于此段端点的报警阈值。这些值来自此对象引用的报警配置配置文件。此对象的值是HDSL2SHDSLendPointAlarmConfProfile表中引用的配置文件的索引，或NULL（零长度SNMPAdministring）。如果该值为零长度SNMPAdministring，则端点将根据hdsl2ShdslSpanConfTable中的hdsl2ShdslSpanConfAlarmProfile对象，使用关联范围的默认报警配置文件。此对象的默认值为零长度snmpadmin字符串。
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslEndpointConfEntry 3 }
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslEndpointConfEntry 3 }
-- Segment Endpoint Current Status/Performance Group --
--段端点当前状态/性能组--
hdsl2ShdslEndpointCurrTable OBJECT-TYPE SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry MAX-ACCESS not-accessible STATUS current
Hdsl2ShdslEndpointCurrEntry的hdsl2ShdslEndpointCurrTable对象类型语法序列MAX-ACCESS不可访问状态当前
DESCRIPTION
"This table contains current status and performance information
for segment endpoints in HDSL2/SHDSL Lines. As with other
tables in this MIB indexed by ifIndex, entries in this table
MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 5 }
DESCRIPTION
"This table contains current status and performance information
for segment endpoints in HDSL2/SHDSL Lines. As with other
tables in this MIB indexed by ifIndex, entries in this table
MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 5 }
hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointCurrTable. Each entry
contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of the
HDSL2/SHDSL line, the UnitId of the associated unit, the side
of the unit, and the wire-pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair }
::= { hdsl2ShdslEndpointCurrTable 1 }
hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointCurrTable. Each entry
contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of the
HDSL2/SHDSL line, the UnitId of the associated unit, the side
of the unit, and the wire-pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair }
::= { hdsl2ShdslEndpointCurrTable 1 }
Hdsl2ShdslEndpointCurrEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointCurrAtn Integer32,
hdsl2ShdslEndpointCurrSnrMgn Integer32,
hdsl2ShdslEndpointCurrStatus BITS,
hdsl2ShdslEndpointES Counter32,
hdsl2ShdslEndpointSES Counter32,
hdsl2ShdslEndpointCRCanomalies Counter32,
hdsl2ShdslEndpointLOSWS Counter32,
hdsl2ShdslEndpointUAS Counter32,
hdsl2ShdslEndpointCurr15MinTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr15MinES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinSES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinCRCanomalies PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinLOSWS PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinUAS PerfCurrentCount,
hdsl2ShdslEndpointCurr1DayTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr1DayES
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DaySES
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayCRCanomalies
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayLOSWS
Hdsl2ShdslEndpointCurrEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointCurrAtn Integer32,
hdsl2ShdslEndpointCurrSnrMgn Integer32,
hdsl2ShdslEndpointCurrStatus BITS,
hdsl2ShdslEndpointES Counter32,
hdsl2ShdslEndpointSES Counter32,
hdsl2ShdslEndpointCRCanomalies Counter32,
hdsl2ShdslEndpointLOSWS Counter32,
hdsl2ShdslEndpointUAS Counter32,
hdsl2ShdslEndpointCurr15MinTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr15MinES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinSES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinCRCanomalies PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinLOSWS PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinUAS PerfCurrentCount,
hdsl2ShdslEndpointCurr1DayTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr1DayES
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DaySES
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayCRCanomalies
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayLOSWS
Hdsl2ShdslPerfCurrDayCount, hdsl2ShdslEndpointCurr1DayUAS Hdsl2ShdslPerfCurrDayCount }
Hdsl2ShdslPerfCurrDayCount，hdsl2ShdslEndpointCurr1DayUAS Hdsl2ShdslPerfCurrDayCount}
hdsl2ShdslEndpointCurrAtn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current loop attenuation for this endpoint as reported in
a Network or Customer Side Performance Status message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 1 }
hdsl2ShdslEndpointCurrAtn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current loop attenuation for this endpoint as reported in
a Network or Customer Side Performance Status message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 1 }
hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current SNR margin for this endpoint as reported in a
Status Response/SNR message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 2 }
hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current SNR margin for this endpoint as reported in a
Status Response/SNR message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 2 }
hdsl2ShdslEndpointCurrStatus OBJECT-TYPE
SYNTAX BITS
{
noDefect(0),
powerBackoff(1),
deviceFault(2),
dcContinuityFault(3),
snrMarginAlarm(4),
loopAttenuationAlarm(5),
loswFailureAlarm(6),
configInitFailure(7),
protocolInitFailure(8),
noNeighborPresent(9),
loopbackActive(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the current state of the endpoint. This is a
bitmap of possible conditions. The various bit positions
are:
hdsl2ShdslEndpointCurrStatus OBJECT-TYPE
SYNTAX BITS
{
noDefect(0),
powerBackoff(1),
deviceFault(2),
dcContinuityFault(3),
snrMarginAlarm(4),
loopAttenuationAlarm(5),
loswFailureAlarm(6),
configInitFailure(7),
protocolInitFailure(8),
noNeighborPresent(9),
loopbackActive(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the current state of the endpoint. This is a
bitmap of possible conditions. The various bit positions
are:
noDefect There no defects on the line.
无缺陷。生产线上没有缺陷。
powerBackoff Indicates enhanced Power Backoff.
powerBackoff表示增强的电源后退。
deviceFault Indicates a vendor-dependent diagnostic or self-test fault has been detected.
deviceFault表示检测到供应商相关的诊断或自检故障。
dcContinuityFault Indicates vendor-dependent conditions that interfere with span powering such as short and open circuits.
dcContinuityFault表示干扰跨度供电的供应商相关条件，如短路和断路。
snrMarginAlarm Indicates that the SNR margin has dropped below the alarm threshold.
snrMarginAlarm表示SNR裕度已降至报警阈值以下。
loopAttenuationAlarm Indicates that the loop attenuation exceeds the alarm threshold.
LoopAttendationArm表示环路衰减超过报警阈值。
loswFailureAlarm Indicates a forward LOSW alarm.
loswFailureAlarm表示正向LOSW报警。
configInitFailure Endpoint failure during initialization due to paired endpoint not able to support requested configuration.
由于配对端点无法支持请求的配置，初始化期间configInitFailure端点失败。
protocolInitFailure Endpoint failure during initialization due to incompatible protocol used by the paired endpoint.
protocolInitFailure由于配对终结点使用的协议不兼容，在初始化期间终结点失败。
noNeighborPresent Endpoint failure during initialization due to no activation sequence detected from paired endpoint.
由于未从配对端点检测到激活序列，因此初始化期间非IGHBorPresent端点失败。
loopbackActive A loopback is currently active at this Segment Endpoint.
loopbackActive环回当前在此段端点处于活动状态。
This is intended to supplement ifOperStatus. Note that there
is a 1-1 relationship between the status bits defined in this
object and the notification thresholds defined elsewhere in
this MIB."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 3 }
This is intended to supplement ifOperStatus. Note that there
is a 1-1 relationship between the status bits defined in this
object and the notification thresholds defined elsewhere in
this MIB."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 3 }
hdsl2ShdslEndpointES OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current
hdsl2ShdslEndpointES对象类型语法计数器32个单位“秒”最大访问只读状态当前
DESCRIPTION
"Count of Errored Seconds (ES) on this endpoint since the xU
was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 4 }
DESCRIPTION
"Count of Errored Seconds (ES) on this endpoint since the xU
was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 4 }
hdsl2ShdslEndpointSES OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) on this endpoint
since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 5 }
hdsl2ShdslEndpointSES OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) on this endpoint
since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 5 }
hdsl2ShdslEndpointCRCanomalies OBJECT-TYPE
SYNTAX Counter32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies on this endpoint since the xU was
last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 6 }
hdsl2ShdslEndpointCRCanomalies OBJECT-TYPE
SYNTAX Counter32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies on this endpoint since the xU was
last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 6 }
hdsl2ShdslEndpointLOSWS OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds on this endpoint
since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 7 }
hdsl2ShdslEndpointLOSWS OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds on this endpoint
since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 7 }
hdsl2ShdslEndpointUAS OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Unavailable Seconds (UAS) on this endpoint since the xU was last restarted." REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
hdsl2ShdslEndpointUAS对象类型语法计数器32个单位“秒”最大访问只读状态当前描述“自上次重新启动xU以来，此端点上的不可用秒数（UAS）。“参考”HDSL2第7.5.3.7节；SHDSL第9.5.5.7节
::= { hdsl2ShdslEndpointCurrEntry 8 }
::= { hdsl2ShdslEndpointCurrEntry 8 }
hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in the current 15-minute interval."
::= { hdsl2ShdslEndpointCurrEntry 9 }
hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in the current 15-minute interval."
::= { hdsl2ShdslEndpointCurrEntry 9 }
hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) in the current 15-minute
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 10 }
hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) in the current 15-minute
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 10 }
hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) in the current
15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 11 }
hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) in the current
15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 11 }
hdsl2ShdslEndpointCurr15MinCRCanomalies OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies in the current 15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 12 }
hdsl2ShdslEndpointCurr15MinCRCanomalies OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies in the current 15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 12 }
hdsl2ShdslEndpointCurr15MinLOSWS OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current
hdsl2ShdslEndpointCurr15MinLOSWS对象类型语法PerfCurrentCount单位“秒”最大访问只读状态当前
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds in the current
15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 13 }
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds in the current
15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 13 }
hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) in the current 15-minute
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 14 }
hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) in the current 15-minute
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 14 }
hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds that have elapsed since the beginning of
the current 1-day interval."
::= { hdsl2ShdslEndpointCurrEntry 15 }
hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds that have elapsed since the beginning of
the current 1-day interval."
::= { hdsl2ShdslEndpointCurrEntry 15 }
hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 16 }
hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 16 }
hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 17 }
hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 17 }
hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the current day as measured
by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 18 }
hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the current day as measured
by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 18 }
hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 19 }
hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 19 }
hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 20 }
hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 20 }
-- Segment Endpoint 15-Minute Interval Status/Performance Group --
--分段终点15分钟间隔状态/性能组--
hdsl2Shdsl15MinIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 6 }
hdsl2Shdsl15MinIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 6 }
hdsl2Shdsl15MinIntervalEntry OBJECT-TYPE SYNTAX Hdsl2Shdsl15MinIntervalEntry
HDSL2SHDSL15MiniIntervalentry对象类型语法HDSL2SHDSL15MiniIntervalentry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2Shdsl15MinIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}
::= { hdsl2Shdsl15MinIntervalTable 1 }
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2Shdsl15MinIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}
::= { hdsl2Shdsl15MinIntervalTable 1 }
Hdsl2Shdsl15MinIntervalEntry ::=
SEQUENCE
{
hdsl2Shdsl15MinIntervalNumber Unsigned32,
hdsl2Shdsl15MinIntervalES PerfIntervalCount,
hdsl2Shdsl15MinIntervalSES PerfIntervalCount,
hdsl2Shdsl15MinIntervalCRCanomalies PerfIntervalCount,
hdsl2Shdsl15MinIntervalLOSWS PerfIntervalCount,
hdsl2Shdsl15MinIntervalUAS PerfIntervalCount
}
Hdsl2Shdsl15MinIntervalEntry ::=
SEQUENCE
{
hdsl2Shdsl15MinIntervalNumber Unsigned32,
hdsl2Shdsl15MinIntervalES PerfIntervalCount,
hdsl2Shdsl15MinIntervalSES PerfIntervalCount,
hdsl2Shdsl15MinIntervalCRCanomalies PerfIntervalCount,
hdsl2Shdsl15MinIntervalLOSWS PerfIntervalCount,
hdsl2Shdsl15MinIntervalUAS PerfIntervalCount
}
hdsl2Shdsl15MinIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Performance Data Interval number. 1 is the the most recent
previous interval; interval 96 is 24 hours ago. Intervals
2..96 are optional."
::= { hdsl2Shdsl15MinIntervalEntry 1 }
hdsl2Shdsl15MinIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Performance Data Interval number. 1 is the the most recent
previous interval; interval 96 is 24 hours ago. Intervals
2..96 are optional."
::= { hdsl2Shdsl15MinIntervalEntry 1 }
hdsl2Shdsl15MinIntervalES OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 2 }
hdsl2Shdsl15MinIntervalES OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 2 }
hdsl2Shdsl15MinIntervalSES OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 3 }
hdsl2Shdsl15MinIntervalSES OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 3 }
hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 4 }
hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 4 }
hdsl2Shdsl15MinIntervalLOSWS OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 5 }
hdsl2Shdsl15MinIntervalLOSWS OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 5 }
hdsl2Shdsl15MinIntervalUAS OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 6 }
hdsl2Shdsl15MinIntervalUAS OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 6 }
-- Segment Endpoint 1-Day Interval Status/Performance Group --
--分段终点1天间隔状态/绩效组--
hdsl2Shdsl1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 7 }
hdsl2Shdsl1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 7 }
hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE SYNTAX Hdsl2Shdsl1DayIntervalEntry MAX-ACCESS not-accessible STATUS current
hdsl2Shdsl1DayIntervalEntry对象类型语法hdsl2Shdsl1DayIntervalEntry MAX-ACCESS不可访问状态当前
DESCRIPTION
"An entry in the hdsl2Shdsl1DayIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalNumber }
::= { hdsl2Shdsl1DayIntervalTable 1 }
DESCRIPTION
"An entry in the hdsl2Shdsl1DayIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalNumber }
::= { hdsl2Shdsl1DayIntervalTable 1 }
Hdsl2Shdsl1DayIntervalEntry ::=
SEQUENCE
{
hdsl2Shdsl1DayIntervalNumber Unsigned32,
hdsl2Shdsl1DayIntervalMoniSecs Hdsl2ShdslPerfTimeElapsed,
hdsl2Shdsl1DayIntervalES Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalSES Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalCRCanomalies Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalLOSWS Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalUAS Hdsl2Shdsl1DayIntervalCount
}
Hdsl2Shdsl1DayIntervalEntry ::=
SEQUENCE
{
hdsl2Shdsl1DayIntervalNumber Unsigned32,
hdsl2Shdsl1DayIntervalMoniSecs Hdsl2ShdslPerfTimeElapsed,
hdsl2Shdsl1DayIntervalES Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalSES Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalCRCanomalies Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalLOSWS Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalUAS Hdsl2Shdsl1DayIntervalCount
}
hdsl2Shdsl1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"History Data Interval number. Interval 1 is the the most
recent previous day; interval 30 is 30 days ago. Intervals
2..30 are optional."
::= { hdsl2Shdsl1DayIntervalEntry 1 }
hdsl2Shdsl1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"History Data Interval number. Interval 1 is the the most
recent previous day; interval 30 is 30 days ago. Intervals
2..30 are optional."
::= { hdsl2Shdsl1DayIntervalEntry 1 }
hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time in the 1-day interval over which the
performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not
be collected for any reason."
::= { hdsl2Shdsl1DayIntervalEntry 2 }
hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time in the 1-day interval over which the
performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not
be collected for any reason."
::= { hdsl2Shdsl1DayIntervalEntry 2 }
hdsl2Shdsl1DayIntervalES OBJECT-TYPE SYNTAX Hdsl2Shdsl1DayIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds (ES) during the 1-day interval as
hdsl2Shdsl1DayIntervalES对象类型语法Hdsl2Shdsl1DayIntervalCount单位“秒数”最大访问只读状态当前描述“1天间隔内出错秒数”如下
measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 3 }
measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 3 }
hdsl2Shdsl1DayIntervalSES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 4 }
hdsl2Shdsl1DayIntervalSES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 4 }
hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 5 }
hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 5 }
hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 6 }
hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 6 }
hdsl2Shdsl1DayIntervalUAS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the 1-day interval
as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 7 }
hdsl2Shdsl1DayIntervalUAS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the 1-day interval
as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 7 }
-- Maintenance Group --
--维修组--
hdsl2ShdslEndpointMaintTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports maintenance operations (eg. loopbacks)
to be performed on HDSL2/SHDSL segment endpoints. This table
contains live data from equipment. As such, it is NOT
persistent."
::= { hdsl2ShdslMibObjects 8 }
hdsl2ShdslEndpointMaintTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports maintenance operations (eg. loopbacks)
to be performed on HDSL2/SHDSL segment endpoints. This table
contains live data from equipment. As such, it is NOT
persistent."
::= { hdsl2ShdslMibObjects 8 }
hdsl2ShdslEndpointMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointMaintTable. Each entry
corresponds to a single segment endpoint, and is indexed by the
ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
unit and the side of the unit."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide }
::= { hdsl2ShdslEndpointMaintTable 1 }
hdsl2ShdslEndpointMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointMaintTable. Each entry
corresponds to a single segment endpoint, and is indexed by the
ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
unit and the side of the unit."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide }
::= { hdsl2ShdslEndpointMaintTable 1 }
Hdsl2ShdslEndpointMaintEntry ::=
SEQUENCE
{
hdsl2ShdslMaintLoopbackConfig INTEGER,
hdsl2ShdslMaintTipRingReversal INTEGER,
hdsl2ShdslMaintPowerBackOff INTEGER,
hdsl2ShdslMaintSoftRestart INTEGER
}
Hdsl2ShdslEndpointMaintEntry ::=
SEQUENCE
{
hdsl2ShdslMaintLoopbackConfig INTEGER,
hdsl2ShdslMaintTipRingReversal INTEGER,
hdsl2ShdslMaintPowerBackOff INTEGER,
hdsl2ShdslMaintSoftRestart INTEGER
}
hdsl2ShdslMaintLoopbackConfig OBJECT-TYPE
SYNTAX INTEGER
{
noLoopback(1),
normalLoopback(2),
specialLoopback(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls configuration of loopbacks for the
associated segment endpoint. The status of the loopback
is obtained via the hdsl2ShdslEndpointCurrStatus object."
hdsl2ShdslMaintLoopbackConfig OBJECT-TYPE
SYNTAX INTEGER
{
noLoopback(1),
normalLoopback(2),
specialLoopback(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls configuration of loopbacks for the
associated segment endpoint. The status of the loopback
is obtained via the hdsl2ShdslEndpointCurrStatus object."
::= { hdsl2ShdslEndpointMaintEntry 1 }
::= { hdsl2ShdslEndpointMaintEntry 1 }
hdsl2ShdslMaintTipRingReversal OBJECT-TYPE
SYNTAX INTEGER
{
normal(1),
reversed(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the state of the tip/ring pair at the
associated segment endpoint."
::= { hdsl2ShdslEndpointMaintEntry 2 }
hdsl2ShdslMaintTipRingReversal OBJECT-TYPE
SYNTAX INTEGER
{
normal(1),
reversed(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the state of the tip/ring pair at the
associated segment endpoint."
::= { hdsl2ShdslEndpointMaintEntry 2 }
hdsl2ShdslMaintPowerBackOff OBJECT-TYPE
SYNTAX INTEGER
{
default(1),
enhanced(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the receiver at the associated
segment endpoint to operate in default or enhanced power
backoff mode."
::= { hdsl2ShdslEndpointMaintEntry 3 }
hdsl2ShdslMaintPowerBackOff OBJECT-TYPE
SYNTAX INTEGER
{
default(1),
enhanced(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the receiver at the associated
segment endpoint to operate in default or enhanced power
backoff mode."
::= { hdsl2ShdslEndpointMaintEntry 3 }
hdsl2ShdslMaintSoftRestart OBJECT-TYPE
SYNTAX INTEGER
{
ready(1),
restart(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object enables the manager to trigger a soft restart
of the modem at the associated segment endpoint. The manager
may only set this object to the 'restart(2)' value, which
initiates a restart. The agent will perform a restart after
approximately 5 seconds. Following the 5 second period, the
agent will restore the object to the 'ready(1)' state."
::= { hdsl2ShdslEndpointMaintEntry 4 }
hdsl2ShdslMaintSoftRestart OBJECT-TYPE
SYNTAX INTEGER
{
ready(1),
restart(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object enables the manager to trigger a soft restart
of the modem at the associated segment endpoint. The manager
may only set this object to the 'restart(2)' value, which
initiates a restart. The agent will perform a restart after
approximately 5 seconds. Following the 5 second period, the
agent will restore the object to the 'ready(1)' state."
::= { hdsl2ShdslEndpointMaintEntry 4 }
hdsl2ShdslUnitMaintTable OBJECT-TYPE SYNTAX SEQUENCE OF Hdsl2ShdslUnitMaintEntry
Hdsl2ShdslUnitMaintEntry的hdsl2ShdslUnitMaintTable对象类型语法序列
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports maintenance operations for units in a
HDSL2/SHDSL line. Entries in this table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 9 }
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports maintenance operations for units in a
HDSL2/SHDSL line. Entries in this table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 9 }
hdsl2ShdslUnitMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslUnitMaintTable. Each entry
corresponds to a single unit, and is indexed by the ifIndex
of the HDSL2/SHDSL line and the UnitId of the associated
unit."
INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslUnitMaintTable 1 }
hdsl2ShdslUnitMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslUnitMaintTable. Each entry
corresponds to a single unit, and is indexed by the ifIndex
of the HDSL2/SHDSL line and the UnitId of the associated
unit."
INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslUnitMaintTable 1 }
Hdsl2ShdslUnitMaintEntry ::=
SEQUENCE
{
hdsl2ShdslMaintLoopbackTimeout Integer32,
hdsl2ShdslMaintUnitPowerSource INTEGER
}
Hdsl2ShdslUnitMaintEntry ::=
SEQUENCE
{
hdsl2ShdslMaintLoopbackTimeout Integer32,
hdsl2ShdslMaintUnitPowerSource INTEGER
}
hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE
SYNTAX Integer32(0..4095)
UNITS "minutes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the timeout value for loopbacks
initiated at segments endpoints contained in the associated
unit. A value of 0 disables the timeout."
::= { hdsl2ShdslUnitMaintEntry 1 }
hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE
SYNTAX Integer32(0..4095)
UNITS "minutes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the timeout value for loopbacks
initiated at segments endpoints contained in the associated
unit. A value of 0 disables the timeout."
::= { hdsl2ShdslUnitMaintEntry 1 }
hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE
SYNTAX INTEGER
{
local(1),
span(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the DC power source being used by the
hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE
SYNTAX INTEGER
{
local(1),
span(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the DC power source being used by the
associated unit."
::= { hdsl2ShdslUnitMaintEntry 2 }
associated unit."
::= { hdsl2ShdslUnitMaintEntry 2 }
-- Span Configuration Profile Group --
--Span配置配置文件组--
hdsl2ShdslSpanConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports definitions of span configuration
profiles for SHDSL lines. HDSL2 does not support these
configuration options. This table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 10 }
hdsl2ShdslSpanConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports definitions of span configuration
profiles for SHDSL lines. HDSL2 does not support these
configuration options. This table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 10 }
hdsl2ShdslSpanConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted using the row creation/deletion mechanism
via hdsl2ShdslSpanConfProfileRowStatus. If an active
entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
INDEX { IMPLIED hdsl2ShdslSpanConfProfileName }
::= { hdsl2ShdslSpanConfProfileTable 1 }
hdsl2ShdslSpanConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted using the row creation/deletion mechanism
via hdsl2ShdslSpanConfProfileRowStatus. If an active
entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
INDEX { IMPLIED hdsl2ShdslSpanConfProfileName }
::= { hdsl2ShdslSpanConfProfileTable 1 }
Hdsl2ShdslSpanConfProfileEntry ::=
SEQUENCE
{
hdsl2ShdslSpanConfProfileName SnmpAdminString,
hdsl2ShdslSpanConfWireInterface INTEGER,
hdsl2ShdslSpanConfMinLineRate Unsigned32,
hdsl2ShdslSpanConfMaxLineRate Unsigned32,
hdsl2ShdslSpanConfPSD INTEGER,
hdsl2ShdslSpanConfTransmissionMode
Hdsl2ShdslTransmissionModeType,
hdsl2ShdslSpanConfRemoteEnabled INTEGER,
hdsl2ShdslSpanConfPowerFeeding INTEGER,
hdsl2ShdslSpanConfCurrCondTargetMarginDown Integer32,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown Integer32,
Hdsl2ShdslSpanConfProfileEntry ::=
SEQUENCE
{
hdsl2ShdslSpanConfProfileName SnmpAdminString,
hdsl2ShdslSpanConfWireInterface INTEGER,
hdsl2ShdslSpanConfMinLineRate Unsigned32,
hdsl2ShdslSpanConfMaxLineRate Unsigned32,
hdsl2ShdslSpanConfPSD INTEGER,
hdsl2ShdslSpanConfTransmissionMode
Hdsl2ShdslTransmissionModeType,
hdsl2ShdslSpanConfRemoteEnabled INTEGER,
hdsl2ShdslSpanConfPowerFeeding INTEGER,
hdsl2ShdslSpanConfCurrCondTargetMarginDown Integer32,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown Integer32,
hdsl2ShdslSpanConfCurrCondTargetMarginUp Integer32, hdsl2ShdslSpanConfWorstCaseTargetMarginUp Integer32, hdsl2ShdslSpanConfUsedTargetMargins BITS, hdsl2ShdslSpanConfReferenceClock Hdsl2ShdslClockReferenceType, hdsl2ShdslSpanConfLineProbeEnable INTEGER, hdsl2ShdslSpanConfProfileRowStatus RowStatus }
hdsl2ShdslSpanConfCurrCondTargetMarginUp整数32，hdsl2ShdslSpanConfWorstCaseTargetMarginUp整数32，HDSL2SHDSLSPANConfConfusedTargetMargins位，HDSL2SHDSLSPANConfReferenceLock Hdsl2ShdslClockReferenceType，HDSL2SHDSLSPANConfConflineprobleInteger，hdsl2ShdslSpanConfProfileRowStatus行状态}
hdsl2ShdslSpanConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is the unique index associated with this profile.
Entries in this table are referenced via the object
hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry."
::= { hdsl2ShdslSpanConfProfileEntry 1 }
hdsl2ShdslSpanConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is the unique index associated with this profile.
Entries in this table are referenced via the object
hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry."
::= { hdsl2ShdslSpanConfProfileEntry 1 }
hdsl2ShdslSpanConfWireInterface OBJECT-TYPE
SYNTAX INTEGER
{
twoWire(1),
fourWire(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the two-wire or optional four-wire
operation for SHDSL Lines."
DEFVAL { twoWire }
::= { hdsl2ShdslSpanConfProfileEntry 2 }
hdsl2ShdslSpanConfWireInterface OBJECT-TYPE
SYNTAX INTEGER
{
twoWire(1),
fourWire(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the two-wire or optional four-wire
operation for SHDSL Lines."
DEFVAL { twoWire }
::= { hdsl2ShdslSpanConfProfileEntry 2 }
hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4112000)
UNITS "bps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 3 }
hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4112000)
UNITS "bps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 3 }
hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4112000)
UNITS "bps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 4 }
hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4112000)
UNITS "bps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 4 }
hdsl2ShdslSpanConfPSD OBJECT-TYPE
SYNTAX INTEGER
{
symmetric(1),
asymmetric(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures use of symmetric/asymmetric PSD (Power
Spectral Density) Mask for the associated SHDSL Line. Support
for symmetric PSD is mandatory for all supported data rates.
Support for asymmetric PSD is optional."
DEFVAL { symmetric }
::= { hdsl2ShdslSpanConfProfileEntry 5 }
hdsl2ShdslSpanConfPSD OBJECT-TYPE
SYNTAX INTEGER
{
symmetric(1),
asymmetric(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures use of symmetric/asymmetric PSD (Power
Spectral Density) Mask for the associated SHDSL Line. Support
for symmetric PSD is mandatory for all supported data rates.
Support for asymmetric PSD is optional."
DEFVAL { symmetric }
::= { hdsl2ShdslSpanConfProfileEntry 5 }
hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the regional setting for the SHDSL
line."
DEFVAL { { region1 } }
::= { hdsl2ShdslSpanConfProfileEntry 6 }
hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the regional setting for the SHDSL
line."
DEFVAL { { region1 } }
::= { hdsl2ShdslSpanConfProfileEntry 6 }
hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE
SYNTAX INTEGER
{
enabled(1),
disabled(2)
}
MAX-ACCESS read-create
hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE
SYNTAX INTEGER
{
enabled(1),
disabled(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for remote management
of the units in a SHDSL line from the STU-R via the EOC."
DEFVAL { enabled }
::= { hdsl2ShdslSpanConfProfileEntry 7 }
STATUS current
DESCRIPTION
"This object enables/disables support for remote management
of the units in a SHDSL line from the STU-R via the EOC."
DEFVAL { enabled }
::= { hdsl2ShdslSpanConfProfileEntry 7 }
hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE
SYNTAX INTEGER
{
noPower(1),
powerFeed(2),
wettingCurrent(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for optional power
feeding in a SHDSL line."
DEFVAL { noPower }
::= { hdsl2ShdslSpanConfProfileEntry 8 }
hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE
SYNTAX INTEGER
{
noPower(1),
powerFeed(2),
wettingCurrent(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for optional power
feeding in a SHDSL line."
DEFVAL { noPower }
::= { hdsl2ShdslSpanConfProfileEntry 8 }
hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the downstream current condition target
SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 9 }
hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the downstream current condition target
SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 9 }
hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the downstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 10 }
hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the downstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 10 }
hdsl2ShdslSpanConfCurrCondTargetMarginUp OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the upstream current condition target
SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 11 }
hdsl2ShdslSpanConfCurrCondTargetMarginUp OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the upstream current condition target
SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 11 }
hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the upstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 12 }
hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the upstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 12 }
hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE
SYNTAX BITS
{
currCondDown(0),
worstCaseDown(1),
currCondUp(2),
worstCaseUp(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Contains indicates whether a target SNR margin is enabled or
disabled. This is a bit-map of possible settings. The
various bit positions are:
hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE
SYNTAX BITS
{
currCondDown(0),
worstCaseDown(1),
currCondUp(2),
worstCaseUp(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Contains indicates whether a target SNR margin is enabled or
disabled. This is a bit-map of possible settings. The
various bit positions are:
currCondDown current condition downstream target SNR margin enabled
当前条件下游目标信噪比裕度启用
worstCaseDown worst case downstream target SNR margin enabled
worstCaseDown最坏情况下游目标信噪比裕度启用
currCondUp current condition upstream target SNR
当前条件上游目标信噪比
margin enabled
保证金启用
worstCaseUp worst case upstream target SNR margin
enabled."
DEFVAL { { currCondDown } }
::= { hdsl2ShdslSpanConfProfileEntry 13 }
worstCaseUp worst case upstream target SNR margin
enabled."
DEFVAL { { currCondDown } }
::= { hdsl2ShdslSpanConfProfileEntry 13 }
hdsl2ShdslSpanConfReferenceClock OBJECT-TYPE
SYNTAX Hdsl2ShdslClockReferenceType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the clock reference for the STU-C
in a SHDSL Line."
DEFVAL { localClk }
::= { hdsl2ShdslSpanConfProfileEntry 14 }
hdsl2ShdslSpanConfReferenceClock OBJECT-TYPE
SYNTAX Hdsl2ShdslClockReferenceType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the clock reference for the STU-C
in a SHDSL Line."
DEFVAL { localClk }
::= { hdsl2ShdslSpanConfProfileEntry 14 }
hdsl2ShdslSpanConfLineProbeEnable OBJECT-TYPE
SYNTAX INTEGER
{
disable(1),
enable(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for Line Probe of
the units in a SHDSL line. When Line Probe is enabled, the
system performs Line Probing to find the best possible
rate. If Line probe is disabled, the rate adaptation phase
is skipped to shorten set up time."
DEFVAL { disable }
::= { hdsl2ShdslSpanConfProfileEntry 15 }
hdsl2ShdslSpanConfLineProbeEnable OBJECT-TYPE
SYNTAX INTEGER
{
disable(1),
enable(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for Line Probe of
the units in a SHDSL line. When Line Probe is enabled, the
system performs Line Probing to find the best possible
rate. If Line probe is disabled, the rate adaptation phase
is skipped to shorten set up time."
DEFVAL { disable }
::= { hdsl2ShdslSpanConfProfileEntry 15 }
hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in this table per the semantics of RowStatus. If an
active entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
::= { hdsl2ShdslSpanConfProfileEntry 16 }
hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in this table per the semantics of RowStatus. If an
active entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
::= { hdsl2ShdslSpanConfProfileEntry 16 }
-- Segment Endpoint Alarm Configuration Profile group --
--段端点报警配置配置文件组--
hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports definitions of alarm configuration
profiles for HDSL2/SHDSL segment endpoints. This table
MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 11 }
hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports definitions of alarm configuration
profiles for HDSL2/SHDSL segment endpoints. This table
MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 11 }
hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single alarm configuration profile.
Each profile contains a set of parameters for setting alarm
thresholds for various performance attributes monitored at
HDSL2/SHDSL segment endpoints. Profiles may be created/deleted
using the row creation/deletion mechanism via
hdsl2ShdslEndpointAlarmConfProfileRowStatus. If an active
entry is referenced in either hdsl2ShdslSpanConfAlarmProfile
or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName }
::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 }
hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single alarm configuration profile.
Each profile contains a set of parameters for setting alarm
thresholds for various performance attributes monitored at
HDSL2/SHDSL segment endpoints. Profiles may be created/deleted
using the row creation/deletion mechanism via
hdsl2ShdslEndpointAlarmConfProfileRowStatus. If an active
entry is referenced in either hdsl2ShdslSpanConfAlarmProfile
or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName }
::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 }
Hdsl2ShdslEndpointAlarmConfProfileEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString,
hdsl2ShdslEndpointThreshLoopAttenuation Integer32,
hdsl2ShdslEndpointThreshSNRMargin Integer32,
hdsl2ShdslEndpointThreshES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshSES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshCRCanomalies Integer32,
hdsl2ShdslEndpointThreshLOSWS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshUAS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus
}
Hdsl2ShdslEndpointAlarmConfProfileEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString,
hdsl2ShdslEndpointThreshLoopAttenuation Integer32,
hdsl2ShdslEndpointThreshSNRMargin Integer32,
hdsl2ShdslEndpointThreshES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshSES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshCRCanomalies Integer32,
hdsl2ShdslEndpointThreshLOSWS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshUAS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus
}
hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS not-accessible
hdsl2ShdslEndpointAlarmConfProfileName对象类型语法SnmpAdminString（大小（1..32））MAX-ACCESS不可访问
STATUS current
DESCRIPTION
"This object is the unique index associated with this profile."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 }
STATUS current
DESCRIPTION
"This object is the unique index associated with this profile."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 }
hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the loop attenuation alarm threshold.
When the current value of hdsl2ShdslEndpointCurrAtn reaches
or exceeds this threshold, a hdsl2ShdslLoopAttenCrossing
MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 }
hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the loop attenuation alarm threshold.
When the current value of hdsl2ShdslEndpointCurrAtn reaches
or exceeds this threshold, a hdsl2ShdslLoopAttenCrossing
MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 }
hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the SNR margin alarm threshold.
When the current value of hdsl2ShdslEndpointCurrSnrMgn
reaches or drops below this threshold, a
hdsl2ShdslSNRMarginCrossing MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 }
hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the SNR margin alarm threshold.
When the current value of hdsl2ShdslEndpointCurrSnrMgn
reaches or drops below this threshold, a
hdsl2ShdslSNRMarginCrossing MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 }
hdsl2ShdslEndpointThreshES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
errored seconds (ES) within any given 15-minute performance
data collection interval. If the value of errored seconds
in a particular 15-minute collection interval reaches/
exceeds this value, a hdsl2ShdslPerfESThresh MAY be
generated. At most one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 }
hdsl2ShdslEndpointThreshES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
errored seconds (ES) within any given 15-minute performance
data collection interval. If the value of errored seconds
in a particular 15-minute collection interval reaches/
exceeds this value, a hdsl2ShdslPerfESThresh MAY be
generated. At most one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 }
hdsl2ShdslEndpointThreshSES OBJECT-TYPE
hdsl2shdslendpointthreshes对象类型
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
severely errored seconds (SES) within any given 15-minute
performance data collection interval. If the value of
severely errored seconds in a particular 15-minute collection
interval reaches/exceeds this value, a hdsl2ShdslPerfSESThresh
MAY be generated. At most one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 }
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
severely errored seconds (SES) within any given 15-minute
performance data collection interval. If the value of
severely errored seconds in a particular 15-minute collection
interval reaches/exceeds this value, a hdsl2ShdslPerfSESThresh
MAY be generated. At most one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 }
hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE
SYNTAX Integer32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
CRC anomalies within any given 15-minute performance data
collection interval. If the value of CRC anomalies in a
particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfCRCanomaliesThresh MAY be
generated. At most one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 }
hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE
SYNTAX Integer32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
CRC anomalies within any given 15-minute performance data
collection interval. If the value of CRC anomalies in a
particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfCRCanomaliesThresh MAY be
generated. At most one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 }
hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
Loss of Sync Word (LOSW) Seconds within any given 15-minute
performance data collection interval. If the value of LOSW
in a particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfLOSWSThresh MAY be generated.
At most one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 }
hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
Loss of Sync Word (LOSW) Seconds within any given 15-minute
performance data collection interval. If the value of LOSW
in a particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfLOSWSThresh MAY be generated.
At most one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 }
hdsl2ShdslEndpointThreshUAS OBJECT-TYPE
hdsl2ShdslEndpointThreshUAS对象类型
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
unavailable seconds (UAS) within any given 15-minute
performance data collection interval. If the value of UAS
in a particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfUASThresh MAY be generated.
At most one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 }
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
unavailable seconds (UAS) within any given 15-minute
performance data collection interval. If the value of UAS
in a particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfUASThresh MAY be generated.
At most one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 }
hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in this table as per the semantics of RowStatus.
If an active entry is referenced in either
hdsl2ShdslSpanConfAlarmProfile or
hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 }
hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in this table as per the semantics of RowStatus.
If an active entry is referenced in either
hdsl2ShdslSpanConfAlarmProfile or
hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 }
-- Notifications Group --
--通知组--
hdsl2ShdslNotifications OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 0 }
hdsl2ShdslNotifications OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 0 }
hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointThreshLoopAttenuation
}
STATUS current
DESCRIPTION
"This notification indicates that the loop attenuation
threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation
value) has been reached/exceeded for the HDSL2/SHDSL segment
endpoint."
::= { hdsl2ShdslNotifications 1 }
hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointThreshLoopAttenuation
}
STATUS current
DESCRIPTION
"This notification indicates that the loop attenuation
threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation
value) has been reached/exceeded for the HDSL2/SHDSL segment
endpoint."
::= { hdsl2ShdslNotifications 1 }
hdsl2ShdslSNRMarginCrossing NOTIFICATION-TYPE
hdsl2ShdslSNRMarginCrossing通知类型
OBJECTS {
物体{
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointThreshSNRMargin
}
STATUS current
DESCRIPTION
"This notification indicates that the SNR margin threshold (as
per the hdsl2ShdslEndpointThreshSNRMargin value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 2 }
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointThreshSNRMargin
}
STATUS current
DESCRIPTION
"This notification indicates that the SNR margin threshold (as
per the hdsl2ShdslEndpointThreshSNRMargin value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 2 }
hdsl2ShdslPerfESThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointThreshES
}
STATUS current
DESCRIPTION
"This notification indicates that the errored seconds threshold
(as per the hdsl2ShdslEndpointThreshES value) has been reached/
exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 3 }
hdsl2ShdslPerfESThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointThreshES
}
STATUS current
DESCRIPTION
"This notification indicates that the errored seconds threshold
(as per the hdsl2ShdslEndpointThreshES value) has been reached/
exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 3 }
hdsl2ShdslPerfSESThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointThreshSES
}
STATUS current
DESCRIPTION
"This notification indicates that the severely errored seconds
threshold (as per the hdsl2ShdslEndpointThreshSES value) has
been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."
::= { hdsl2ShdslNotifications 4 }
hdsl2ShdslPerfSESThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointThreshSES
}
STATUS current
DESCRIPTION
"This notification indicates that the severely errored seconds
threshold (as per the hdsl2ShdslEndpointThreshSES value) has
been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."
::= { hdsl2ShdslNotifications 4 }
hdsl2ShdslPerfCRCanomaliesThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointThreshCRCanomalies
}
STATUS current
DESCRIPTION
"This notification indicates that the CRC anomalies threshold
hdsl2ShdslPerfCRCanomaliesThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointThreshCRCanomalies
}
STATUS current
DESCRIPTION
"This notification indicates that the CRC anomalies threshold
(as per the hdsl2ShdslEndpointThreshCRCanomalies value) has
been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."
::= { hdsl2ShdslNotifications 5 }
(as per the hdsl2ShdslEndpointThreshCRCanomalies value) has
been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."
::= { hdsl2ShdslNotifications 5 }
hdsl2ShdslPerfLOSWSThresh NOTIFICATION-TYPE OBJECTS {
HDSL2SHDSLPerflossThresh通知类型对象{
hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointThreshLOSWS
}
STATUS current
DESCRIPTION
"This notification indicates that the LOSW seconds threshold
(as per the hdsl2ShdslEndpointThreshLOSWS value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 6 }
hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointThreshLOSWS
}
STATUS current
DESCRIPTION
"This notification indicates that the LOSW seconds threshold
(as per the hdsl2ShdslEndpointThreshLOSWS value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 6 }
hdsl2ShdslPerfUASThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointThreshUAS
}
STATUS current
DESCRIPTION
"This notification indicates that the unavailable seconds
threshold (as per the hdsl2ShdslEndpointThreshUAS value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 7 }
hdsl2ShdslPerfUASThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointThreshUAS
}
STATUS current
DESCRIPTION
"This notification indicates that the unavailable seconds
threshold (as per the hdsl2ShdslEndpointThreshUAS value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 7 }
hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslSpanConfNumRepeaters
}
STATUS current
DESCRIPTION
"This notification indicates that a mismatch has been detected
between the number of repeater/regenerator units configured
for a HDSL2/SHDSL line via the hdsl2ShdslSpanConfNumRepeaters
object and the actual number of repeater/regenerator units
discovered via the EOC."
::= { hdsl2ShdslNotifications 8 }
hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslSpanConfNumRepeaters
}
STATUS current
DESCRIPTION
"This notification indicates that a mismatch has been detected
between the number of repeater/regenerator units configured
for a HDSL2/SHDSL line via the hdsl2ShdslSpanConfNumRepeaters
object and the actual number of repeater/regenerator units
discovered via the EOC."
::= { hdsl2ShdslNotifications 8 }
hdsl2ShdslLoopbackFailure NOTIFICATION-TYPE OBJECTS {
hdsl2ShdslLoopbackFailure通知类型对象{
hdsl2ShdslMaintLoopbackConfig
}
STATUS current
DESCRIPTION
"This notification indicates that an endpoint maintenance
loopback command failed for an HDSL2/SHDSL segment."
::= { hdsl2ShdslNotifications 9 }
hdsl2ShdslMaintLoopbackConfig
}
STATUS current
DESCRIPTION
"This notification indicates that an endpoint maintenance
loopback command failed for an HDSL2/SHDSL segment."
::= { hdsl2ShdslNotifications 9 }
hdsl2ShdslpowerBackoff NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
powerBackoff in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."
::= { hdsl2ShdslNotifications 10 }
hdsl2ShdslpowerBackoff NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
powerBackoff in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."
::= { hdsl2ShdslNotifications 10 }
hdsl2ShdsldeviceFault NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
deviceFault in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."
::= { hdsl2ShdslNotifications 11 }
hdsl2ShdsldeviceFault NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
deviceFault in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."
::= { hdsl2ShdslNotifications 11 }
hdsl2ShdsldcContinuityFault NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 12 }
hdsl2ShdsldcContinuityFault NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 12 }
hdsl2ShdslconfigInitFailure NOTIFICATION-TYPE OBJECTS { hdsl2ShdslEndpointCurrStatus
hdsl2ShdslconfigInitFailure通知类型对象{hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
configInitFailure in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 13 }
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
configInitFailure in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 13 }
hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
protocolInitFailure in the hdsl2ShdslEndpointCurrStatus
object for this endpoint has changed."
::= { hdsl2ShdslNotifications 14 }
hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
protocolInitFailure in the hdsl2ShdslEndpointCurrStatus
object for this endpoint has changed."
::= { hdsl2ShdslNotifications 14 }
hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 15 }
hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 15 }
hdsl2ShdslLocalPowerLoss NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslInvVendorID
}
STATUS current
DESCRIPTION
"This notification indicates impending unit failure due to
loss of local power (last gasp)."
::= { hdsl2ShdslNotifications 16 }
hdsl2ShdslLocalPowerLoss NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslInvVendorID
}
STATUS current
DESCRIPTION
"This notification indicates impending unit failure due to
loss of local power (last gasp)."
::= { hdsl2ShdslNotifications 16 }
-- conformance information --
--一致性信息--
hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 3 }
hdsl2ShdslGroups OBJECT IDENTIFIER ::=
hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 3 }
hdsl2ShdslGroups OBJECT IDENTIFIER ::=
{ hdsl2ShdslConformance 1 }
hdsl2ShdslCompliances OBJECT IDENTIFIER ::=
{ hdsl2ShdslConformance 2 }
{ hdsl2ShdslConformance 1 }
hdsl2ShdslCompliances OBJECT IDENTIFIER ::=
{ hdsl2ShdslConformance 2 }
-- agent compliance statements
--代理合规声明
hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The section outlines compliance requirements for this MIB."
MODULE
MANDATORY-GROUPS
{
hdsl2ShdslSpanConfGroup,
hdsl2ShdslSpanStatusGroup,
hdsl2ShdslInventoryGroup,
hdsl2ShdslEndpointConfGroup,
hdsl2ShdslEndpointCurrGroup,
hdsl2Shdsl15MinIntervalGroup,
hdsl2Shdsl1DayIntervalGroup,
hdsl2ShdslMaintenanceGroup,
hdsl2ShdslEndpointAlarmConfGroup,
hdsl2ShdslNotificationGroup
}
hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The section outlines compliance requirements for this MIB."
MODULE
MANDATORY-GROUPS
{
hdsl2ShdslSpanConfGroup,
hdsl2ShdslSpanStatusGroup,
hdsl2ShdslInventoryGroup,
hdsl2ShdslEndpointConfGroup,
hdsl2ShdslEndpointCurrGroup,
hdsl2Shdsl15MinIntervalGroup,
hdsl2Shdsl1DayIntervalGroup,
hdsl2ShdslMaintenanceGroup,
hdsl2ShdslEndpointAlarmConfGroup,
hdsl2ShdslNotificationGroup
}
GROUP hdsl2ShdslInventoryShdslGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
组HDSL2SHDSLINVENTORYSHDLSGROUP DESCRIPTION“仅支持SHDSL线路的实现需要对该组的支持。”
GROUP hdsl2ShdslSpanShdslStatusGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
组HDSL2SHDSLspanSHDSLSStatusGroup DESCRIPTION“仅支持SHDSL线路的实现需要对该组的支持。”
GROUP hdsl2ShdslSpanConfProfileGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
组hdsl2ShdslSpanConfProfileGroup DESCRIPTION“仅支持SHDSL线路的实现需要对此组的支持。”
::= { hdsl2ShdslCompliances 1 }
::= { hdsl2ShdslCompliances 1 }
-- units of conformance --
--一致性单位--
hdsl2ShdslSpanConfGroup OBJECT-GROUP OBJECTS {
hdsl2ShdslSpanConfGroup对象组对象{
hdsl2ShdslSpanConfNumRepeaters,
hdsl2ShdslSpanConfProfile,
hdsl2ShdslSpanConfAlarmProfile
}
STATUS current
DESCRIPTION
"This group supports objects for configuring span related
parameters for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 1 }
hdsl2ShdslSpanConfNumRepeaters,
hdsl2ShdslSpanConfProfile,
hdsl2ShdslSpanConfAlarmProfile
}
STATUS current
DESCRIPTION
"This group supports objects for configuring span related
parameters for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 1 }
hdsl2ShdslSpanStatusGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusNumAvailRepeaters
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving span related
status for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 2 }
hdsl2ShdslSpanStatusGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusNumAvailRepeaters
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving span related
status for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 2 }
hdsl2ShdslInventoryShdslGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslInvTransmissionModeCapability
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
inventory information."
::= { hdsl2ShdslGroups 3 }
hdsl2ShdslInventoryShdslGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslInvTransmissionModeCapability
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
inventory information."
::= { hdsl2ShdslGroups 3 }
hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusMaxAttainableLineRate,
hdsl2ShdslStatusActualLineRate,
hdsl2ShdslStatusTransmissionModeCurrent
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
span related status."
::= { hdsl2ShdslGroups 4 }
hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusMaxAttainableLineRate,
hdsl2ShdslStatusActualLineRate,
hdsl2ShdslStatusTransmissionModeCurrent
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
span related status."
::= { hdsl2ShdslGroups 4 }
hdsl2ShdslInventoryGroup OBJECT-GROUP OBJECTS {
hdsl2ShdslInventoryGroup对象组对象{
hdsl2ShdslInvVendorID,
hdsl2ShdslInvVendorModelNumber,
hdsl2ShdslInvVendorSerialNumber,
hdsl2ShdslInvVendorEOCSoftwareVersion,
hdsl2ShdslInvStandardVersion,
hdsl2ShdslInvVendorListNumber,
hdsl2ShdslInvVendorIssueNumber,
hdsl2ShdslInvVendorSoftwareVersion,
hdsl2ShdslInvEquipmentCode,
hdsl2ShdslInvVendorOther
}
STATUS current
DESCRIPTION
"This group supports objects that provide unit inventory
information about the units in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 5 }
hdsl2ShdslInvVendorID,
hdsl2ShdslInvVendorModelNumber,
hdsl2ShdslInvVendorSerialNumber,
hdsl2ShdslInvVendorEOCSoftwareVersion,
hdsl2ShdslInvStandardVersion,
hdsl2ShdslInvVendorListNumber,
hdsl2ShdslInvVendorIssueNumber,
hdsl2ShdslInvVendorSoftwareVersion,
hdsl2ShdslInvEquipmentCode,
hdsl2ShdslInvVendorOther
}
STATUS current
DESCRIPTION
"This group supports objects that provide unit inventory
information about the units in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 5 }
hdsl2ShdslEndpointConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrAtn
}
STATUS current
DESCRIPTION
"This group supports objects for configuring parameters for
segment endpoints in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 6 }
hdsl2ShdslEndpointConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrAtn
}
STATUS current
DESCRIPTION
"This group supports objects for configuring parameters for
segment endpoints in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 6 }
hdsl2ShdslEndpointCurrGroup OBJECT-GROUP OBJECTS { hdsl2ShdslEndpointCurrAtn, hdsl2ShdslEndpointCurrSnrMgn, hdsl2ShdslEndpointCurrStatus, hdsl2ShdslEndpointES, hdsl2ShdslEndpointSES, hdsl2ShdslEndpointCRCanomalies, hdsl2ShdslEndpointLOSWS, hdsl2ShdslEndpointUAS, hdsl2ShdslEndpointCurr15MinTimeElapsed, hdsl2ShdslEndpointCurr15MinES, hdsl2ShdslEndpointCurr15MinSES, hdsl2ShdslEndpointCurr15MinCRCanomalies, hdsl2ShdslEndpointCurr15MinLOSWS, hdsl2ShdslEndpointCurr15MinUAS, hdsl2ShdslEndpointCurr1DayTimeElapsed, hdsl2ShdslEndpointCurr1DayES, hdsl2ShdslEndpointCurr1DaySES,
hdsl2ShdslEndpointCurrGroup对象组对象{hdsl2ShdslEndpointCurrAtn，hdsl2shdslendpointcurrsnmgn，hdsl2shdslendpointcurstatus，hdsl2shdslendpoints，hdsl2ShdslEndpointCRCanomalies，hdsl2shdslendpointcurrsnmgn，hdsl2shdslendpointcurr15minimeepersd，hdsl2ShdslEndpointCurr15MinES，hdsl2ShdslEndpointCurr15MinCRCanomalies、hdsl2ShdslEndpointCurr15MinLOSWS、hdsl2ShdslEndpointCurr15MinUAS、HDSL2SHDSLENDPOINTCURR1DAYTIMEASED、hdsl2ShdslEndpointCurr1DayES、hdsl2ShdslEndpointCurr1DayES、，
hdsl2ShdslEndpointCurr1DayCRCanomalies,
hdsl2ShdslEndpointCurr1DayLOSWS,
hdsl2ShdslEndpointCurr1DayUAS
}
STATUS current
DESCRIPTION
"This group supports objects which provide current status and
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 7 }
hdsl2ShdslEndpointCurr1DayCRCanomalies,
hdsl2ShdslEndpointCurr1DayLOSWS,
hdsl2ShdslEndpointCurr1DayUAS
}
STATUS current
DESCRIPTION
"This group supports objects which provide current status and
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 7 }
hdsl2Shdsl15MinIntervalGroup OBJECT-GROUP
OBJECTS
{
hdsl2Shdsl15MinIntervalES,
hdsl2Shdsl15MinIntervalSES,
hdsl2Shdsl15MinIntervalCRCanomalies,
hdsl2Shdsl15MinIntervalLOSWS,
hdsl2Shdsl15MinIntervalUAS
}
STATUS current
DESCRIPTION
"This group supports objects which maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 15-minute intervals."
::= { hdsl2ShdslGroups 8 }
hdsl2Shdsl15MinIntervalGroup OBJECT-GROUP
OBJECTS
{
hdsl2Shdsl15MinIntervalES,
hdsl2Shdsl15MinIntervalSES,
hdsl2Shdsl15MinIntervalCRCanomalies,
hdsl2Shdsl15MinIntervalLOSWS,
hdsl2Shdsl15MinIntervalUAS
}
STATUS current
DESCRIPTION
"This group supports objects which maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 15-minute intervals."
::= { hdsl2ShdslGroups 8 }
hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP
OBJECTS
{
hdsl2Shdsl1DayIntervalMoniSecs,
hdsl2Shdsl1DayIntervalES,
hdsl2Shdsl1DayIntervalSES,
hdsl2Shdsl1DayIntervalCRCanomalies,
hdsl2Shdsl1DayIntervalLOSWS,
hdsl2Shdsl1DayIntervalUAS
}
STATUS current
DESCRIPTION
"This group supports objects which maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 1-day intervals."
::= { hdsl2ShdslGroups 9 }
hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP
OBJECTS
{
hdsl2Shdsl1DayIntervalMoniSecs,
hdsl2Shdsl1DayIntervalES,
hdsl2Shdsl1DayIntervalSES,
hdsl2Shdsl1DayIntervalCRCanomalies,
hdsl2Shdsl1DayIntervalLOSWS,
hdsl2Shdsl1DayIntervalUAS
}
STATUS current
DESCRIPTION
"This group supports objects which maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 1-day intervals."
::= { hdsl2ShdslGroups 9 }
hdsl2ShdslMaintenanceGroup OBJECT-GROUP OBJECTS { hdsl2ShdslMaintLoopbackConfig,
hdsl2ShdslMaintenanceGroup对象组对象{hdsl2ShdslMaintLoopbackConfig，
hdsl2ShdslMaintTipRingReversal,
hdsl2ShdslMaintPowerBackOff,
hdsl2ShdslMaintSoftRestart,
hdsl2ShdslMaintLoopbackTimeout,
hdsl2ShdslMaintUnitPowerSource
}
STATUS current
DESCRIPTION
"This group supports objects that provide support for
maintenance actions for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 10 }
hdsl2ShdslMaintTipRingReversal,
hdsl2ShdslMaintPowerBackOff,
hdsl2ShdslMaintSoftRestart,
hdsl2ShdslMaintLoopbackTimeout,
hdsl2ShdslMaintUnitPowerSource
}
STATUS current
DESCRIPTION
"This group supports objects that provide support for
maintenance actions for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 10 }
hdsl2ShdslEndpointAlarmConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointAlarmConfProfile,
hdsl2ShdslEndpointThreshLoopAttenuation,
hdsl2ShdslEndpointThreshSNRMargin,
hdsl2ShdslEndpointThreshES,
hdsl2ShdslEndpointThreshSES,
hdsl2ShdslEndpointThreshCRCanomalies,
hdsl2ShdslEndpointThreshLOSWS,
hdsl2ShdslEndpointThreshUAS,
hdsl2ShdslEndpointAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"This group supports objects that allow configuration of alarm
thresholds for various performance parameters for HDSL2/SHDSL
lines."
::= { hdsl2ShdslGroups 11 }
hdsl2ShdslEndpointAlarmConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointAlarmConfProfile,
hdsl2ShdslEndpointThreshLoopAttenuation,
hdsl2ShdslEndpointThreshSNRMargin,
hdsl2ShdslEndpointThreshES,
hdsl2ShdslEndpointThreshSES,
hdsl2ShdslEndpointThreshCRCanomalies,
hdsl2ShdslEndpointThreshLOSWS,
hdsl2ShdslEndpointThreshUAS,
hdsl2ShdslEndpointAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"This group supports objects that allow configuration of alarm
thresholds for various performance parameters for HDSL2/SHDSL
lines."
::= { hdsl2ShdslGroups 11 }
hdsl2ShdslNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { hdsl2ShdslLoopAttenCrossing, hdsl2ShdslSNRMarginCrossing, hdsl2ShdslPerfESThresh, hdsl2ShdslPerfSESThresh, hdsl2ShdslPerfCRCanomaliesThresh, hdsl2ShdslPerfLOSWSThresh, hdsl2ShdslPerfUASThresh, hdsl2ShdslSpanInvalidNumRepeaters, hdsl2ShdslLoopbackFailure, hdsl2ShdslpowerBackoff, hdsl2ShdsldeviceFault, hdsl2ShdsldcContinuityFault, hdsl2ShdslconfigInitFailure,
hdsl2ShdslNotificationGroup通知—组通知{hdsl2ShdslLoopAttenCrossing，hdsl2ShdslSNRMarginCrossing，hdsl2ShdslPerfESThresh，hdsl2ShdslPerfCRCanomaliesThresh，HDSL2SHDSLPerfLoopsThresh，HDSL2SHDSLPerfLoopsThresh，HDSL2SHDSLSpanidInvalidNumRepeaters，hdsl2ShdslLoopbackFailure，HDSL2SHDSL2SHDSLPowerBackoff，HDSL2SHDSL2SHDSLDeviceFault，hdsl2ShdsldcContinuityFault，hdsl2Shdslconfig一旦失败，
hdsl2ShdslprotocolInitFailure,
hdsl2ShdslnoNeighborPresent,
hdsl2ShdslLocalPowerLoss
}
STATUS current
DESCRIPTION
"This group supports notifications of significant conditions
associated with HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 12 }
hdsl2ShdslprotocolInitFailure,
hdsl2ShdslnoNeighborPresent,
hdsl2ShdslLocalPowerLoss
}
STATUS current
DESCRIPTION
"This group supports notifications of significant conditions
associated with HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 12 }
hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslSpanConfWireInterface,
hdsl2ShdslSpanConfMinLineRate,
hdsl2ShdslSpanConfMaxLineRate,
hdsl2ShdslSpanConfPSD,
hdsl2ShdslSpanConfTransmissionMode,
hdsl2ShdslSpanConfRemoteEnabled,
hdsl2ShdslSpanConfPowerFeeding,
hdsl2ShdslSpanConfCurrCondTargetMarginDown,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown,
hdsl2ShdslSpanConfCurrCondTargetMarginUp,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp,
hdsl2ShdslSpanConfUsedTargetMargins,
hdsl2ShdslSpanConfReferenceClock,
hdsl2ShdslSpanConfLineProbeEnable,
hdsl2ShdslSpanConfProfileRowStatus
}
STATUS current
DESCRIPTION
"This group supports objects that constitute configuration
profiles for configuring span related parameters in SHDSL
lines."
::= { hdsl2ShdslGroups 13 }
END
hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslSpanConfWireInterface,
hdsl2ShdslSpanConfMinLineRate,
hdsl2ShdslSpanConfMaxLineRate,
hdsl2ShdslSpanConfPSD,
hdsl2ShdslSpanConfTransmissionMode,
hdsl2ShdslSpanConfRemoteEnabled,
hdsl2ShdslSpanConfPowerFeeding,
hdsl2ShdslSpanConfCurrCondTargetMarginDown,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown,
hdsl2ShdslSpanConfCurrCondTargetMarginUp,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp,
hdsl2ShdslSpanConfUsedTargetMargins,
hdsl2ShdslSpanConfReferenceClock,
hdsl2ShdslSpanConfLineProbeEnable,
hdsl2ShdslSpanConfProfileRowStatus
}
STATUS current
DESCRIPTION
"This group supports objects that constitute configuration
profiles for configuring span related parameters in SHDSL
lines."
::= { hdsl2ShdslGroups 13 }
END
Blocking unauthorized access to the HDSL2-SHDSL MIB via the element management system is outside the scope of this document. It should be noted that access to the MIB permits the unauthorized entity to modify the profiles (section 6.4) such that both subscriber service and network operations can be interfered with. Subscriber service can be altered by modifying any of a number of service characteristics such as rate partitioning and maximum transmission rates. Network operations can be impacted by modification of notification thresholds such as SES thresholds.
阻止通过元件管理系统对HDSL2-SHDSL MIB进行未经授权的访问超出了本文件的范围。应注意的是，对MIB的访问允许未经授权的实体修改配置文件（第6.4节），从而干扰用户服务和网络操作。用户服务可以通过修改许多服务特征中的任何一个来改变，例如速率分区和最大传输速率。修改通知阈值（如SES阈值）可能会影响网络操作。
There are a number of managed objects in this MIB that may be considered to contain sensitive information. Access to these objects would allow an intruder to obtain information about which vendor's equipment is in use on the network. Further, such information is considered sensitive in many environments for competitive reasons.
此MIB中有许多托管对象可能被认为包含敏感信息。对这些对象的访问将允许入侵者获取有关网络上使用的供应商设备的信息。此外，由于竞争原因，此类信息在许多环境中被视为敏感信息。
These identifying objects in the inventory group are:
库存组中的这些标识对象是：
- hdsl2ShdslInvVendorID - hdsl2ShdslInvVendorModelNumber - hdsl2ShdslInvVendorSerialNumber - hdsl2ShdslInvVendorEOCSoftwareVersion - hdsl2ShdslInvStandardVersion - hdsl2ShdslInvVendorListNumber - hdsl2ShdslInvVendorIssueNumber - hdsl2ShdslInvVendorSoftwareVersion - hdsl2ShdslInvEquipmentCode - hdsl2ShdslInvVendorOther - hdsl2ShdslInvTransmissionModeCapability
- HDSL2SHDSLINVENDORID-HDSL2SHDSLINVENDORMODEL NUMBER-HDSL2SHDSLINVENDORSERIALNUMBER-HDSL2SHDSLINVENDOREOC软件版本-HDSL2SHDSLINVANDORISTNERID-HDSL2SHDSLINVENDORISTURE-HDSL2SHDSLINVENDORS软件版本-HDSL2SHDSLINVENDOROSTOHER-HDSL2SHDSLINVTransmissionModelCapability
Therefore, it may be important in some environments to control read access to these objects and possibly to even encrypt the values of these object when sending them over the network via SNMP. Not all versions of SNMP provide features for such a secure environment.
因此，在某些环境中，控制对这些对象的读取访问，甚至可能在通过SNMP通过网络发送这些对象时加密这些对象的值，这可能很重要。并非所有版本的SNMP都为这种安全环境提供功能。
It is recommended that the implementors consider the security features as provided by the SNMPv3 framework. Specifically, the use of the User-based Security Model RFC 2574 [12] and the View-based Access Control Model RFC 2575 [15] are recommended.
建议执行者考虑SNMPv3框架提供的安全特性。具体而言，建议使用基于用户的安全模型RFC 2574[12]和基于视图的访问控制模型RFC 2575[15]。
It is then the customer/user's responsibility to ensure that the SNMP entity giving access to an instance of this MIB, is properly configured to give access to those objects only to those principals (users) that have legitimate rights to access them.
然后，客户/用户有责任确保访问此MIB实例的SNMP实体正确配置为仅向具有合法访问权限的主体（用户）授予访问这些对象的权限。
HDSL2-SHDSL layer connectivity from the xtuR will permit the subscriber to manipulate both the HDSL2-SHDSL link directly and the HDSL2-SHDSL embedded operations channel (EOC) for their own loop. For example, unchecked or unfiltered fluctuations initiated by the subscriber could generate sufficient notifications to potentially overwhelm either the management interface to the network or the element manager.
来自XTAR的HDSL2-SHDSL层连接将允许订户直接操作HDSL2-SHDSL链路和HDSL2-SHDSL嵌入式操作信道（EOC），以实现其自己的环路。例如，订阅者发起的未经检查或未经过滤的波动可能会产生足够的通知，可能会压倒网络或元素管理器的管理接口。
It should be noted that interface indices in this MIB are maintained persistently. VACM data relating to these should be stored persistently.
应该注意的是，此MIB中的接口索引是持久维护的。与这些相关的VACM数据应永久存储。
There are a number of management objects defined in this MIB that have a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations.
此MIB中定义了许多管理对象，它们的MAX-ACCESS子句为read-write和/或read-create。在某些网络环境中，此类对象可能被视为敏感或易受攻击。在没有适当保护的非安全环境中支持SET操作可能会对网络操作产生负面影响。
The authors are deeply grateful to the authors of the ADSL LINE MIB (RFC 2662 [23]), Gregory Bathrick and Faye Ly, as much of the text and structure of this document originates in their documents.
作者非常感谢ADSL线路MIB（RFC 2662[23]）的作者Gregory Bathrick和Faye Ly，因为本文件的大部分文本和结构源自他们的文件。
The authors are also grateful to the authors of FR MFR MIB (RFC 3020 [24]), Prayson Pate, Bob Lynch, and Kenneth Rehbehn, as the majority of the Security Considerations section was lifted from their document.
作者还感谢FR MFR MIB（RFC 3020[24]）、Prayson Pate、Bob Lynch和Kenneth Rehbehn的作者，因为大部分安全考虑部分已从他们的文档中删除。
The authors also acknowledge the importance of the contributions and suggestions regarding interface indexing structures received from David Horton of CITR.
作者还承认了从CITR的David Horton处收到的关于接口索引结构的贡献和建议的重要性。
Other contributions were received from the following:
其他捐款来自下列机构：
Philip Bergstresser (Adtran) Steve Blackwell (Centillium) Umberto Bonollo (NEC Australia) Yagal Hachmon (RAD) Mark Johnson (Red Point) Sharon Mantin (Orckit) Moti Morgenstern (ECI) Raymond Murphy (Ericsson) Lee Nipper (Verilink) Randy Presuhn (BMC Software) Katy Sherman (Orckit) Mike Sneed (ECI) Jon Turney (DSL Solutions) Aron Wahl (Memotec) Bert Wijnen (Lucent) Michael Wrobel (Memotec)
Philip Bergstresser（Adtran）Steve Blackwell（Centillium）Umberto Bonollo（NEC Australia）Yagal Hachmon（RAD）Mark Johnson（Red Point）Sharon Mantin（Orkit）Moti Morgenstern（ECI）Raymond Murphy（Ericsson）Lee Nipper（Verilink）Randy Presohn（BMC Software）Katy Sherman（Orkit）Mike Sneed（ECI）Jon Turney（DSL Solutions）Aron Wahl（Memotec）伯特·维恩（朗讯公司）迈克尔·沃罗贝尔（Memotec公司）
[1] Harrington, D., Presuhn, R. and B. Wijnen, "An Architecture for Describing SNMP Management Frameworks", RFC 2571, April 1999.
[1] Harrington，D.，Presohn，R.和B.Wijnen，“描述SNMP管理框架的体系结构”，RFC 2571，1999年4月。
[2] Rose, M. and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP-based Internets", STD 16, RFC 1155, May 1990.
[2] Rose，M.和K.McCloghrie，“基于TCP/IP的互联网管理信息的结构和识别”，STD 16，RFC 1155，1990年5月。
[3] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD 16, RFC 1212, March 1991.
[3] Rose，M.和K.McCloghrie，“简明MIB定义”，STD 16，RFC 1212，1991年3月。
[4] Rose, M., "A Convention for Defining Traps for use with the SNMP", RFC 1215, March 1991.
[4] Rose，M.“定义用于SNMP的陷阱的约定”，RFC1215，1991年3月。
[5] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[5] McCloghrie，K.，Perkins，D.，Schoenwaeld，J.，Case，J.，Rose，M.和S.Waldbusser，“管理信息的结构版本2（SMIv2）”，STD 58，RFC 2578，1999年4月。
[6] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999.
[6] McCloghrie，K.，Perkins，D.，Schoenwaeld，J.，Case，J.，Rose，M.和S.Waldbusser，“SMIv2的文本约定”，STD 58，RFC 2579，1999年4月。
[7] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999.
[7] McCloghrie，K.，Perkins，D.，Schoenwaeld，J.，Case，J.，Rose，M.和S.Waldbusser，“SMIv2的一致性声明”，STD 58，RFC 25801999年4月。
[8] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple Network Management Protocol", STD 15, RFC 1157, May 1990.
[8] Case，J.，Fedor，M.，Schoffstall，M.和J.Davin，“简单网络管理协议”，STD 15，RFC 1157，1990年5月。
[9] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901, January 1996.
[9] Case，J.，McCloghrie，K.，Rose，M.和S.Waldbusser，“基于社区的SNMPv2简介”，RFC 19011996年1月。
[10] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1906, January 1996.
[10] Case，J.，McCloghrie，K.，Rose，M.和S.Waldbusser，“简单网络管理协议（SNMPv2）版本2的传输映射”，RFC 1906，1996年1月。
[11] Case, J., Harrington D., Presuhn, R. and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)", RFC 2572, April 1999.
[11] Case，J.，Harrington D.，Presohn，R.和B.Wijnen，“简单网络管理协议（SNMP）的消息处理和调度”，RFC 2572，1999年4月。
[12] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", RFC 2574, April 1999.
[12] Blumenthal，U.和B.Wijnen，“简单网络管理协议（SNMPv3）第3版的基于用户的安全模型（USM）”，RFC 2574，1999年4月。
[13] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, January 1996.
[13] Case，J.，McCloghrie，K.，Rose，M.和S.Waldbusser，“简单网络管理协议（SNMPv2）版本2的协议操作”，RFC 1905，1996年1月。
[14] Levi, D., Meyer, P. and B. Stewart, "SNMPv3 Applications", RFC 2573, April 1999.
[14] Levi，D.，Meyer，P.和B.Stewart，“SNMPv3应用”，RFC2573，1999年4月。
[15] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2575, April 1999.
[15] Wijnen，B.，Presuhn，R.和K.McCloghrie，“用于简单网络管理协议（SNMP）的基于视图的访问控制模型（VACM）”，RFC2575，1999年4月。
[16] Case, J., Mundy, R., Partain, D. and B. Stewart, "Introduction to Version 3 of the Internet-standard Network Management Framework", RFC 2570, April 1999.
[16] Case，J.，Mundy，R.，Partain，D.和B.Stewart，“互联网标准网络管理框架第3版简介”，RFC 25701999年4月。
[17] Bradner, S., "Key Words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.
[17] Bradner，S.，“RFC中用于表示需求水平的关键词”，BCP 14，RFC 2119，1997年3月。
[18] American National Standards Institute, ANSI T1E1.4/2000-006, February 2000.
[18] 美国国家标准协会，ANSI T1E1.4/2000-006，2000年2月。
[19] Blackwell, S., Editor, "Single-Pair High-Speed Digital Subscriber Line (SHDSL) Transceivers", ITU-T Draft G.991.2, April 2000.
[19] Blackwell，S.，编辑，“单对高速数字用户线（SHDSL）收发器”，ITU-T草案G.991.2，2000年4月。
[20] McCloghrie, K. and M. Rose, M., "Management Information Base for Network Management of TCP/IP-based internets: MIB-II", STD 17, RFC 1213, March 1991.
[20] McCloghrie，K.和M.Rose，M.，“基于TCP/IP的互联网网络管理的管理信息库：MIB-II”，STD 17，RFC 1213，1991年3月。
[21] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000.
[21] McCloghrie，K.和F.Kastenholz，“接口组MIB”，RFC 28632000年6月。
[22] Tesink, K., "Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals", RFC 2493, January 1999.
[22] Tesink，K.“使用基于15分钟间隔的性能历史记录的MIB模块的文本约定”，RFC 2493，1999年1月。
[23] Bathrick, G. and F. Ly, "Definitions of Managed Objects for the ADSL Lines", RFC 2662, August 1999.
[23] Bathrick，G.和F.Ly，“ADSL线路管理对象的定义”，RFC 2662，1999年8月。
[24] Pate, P., Lynch, B. and K. Rehbehn, "Definitions of Managed Objects for Monitoring and Controlling the UNI/NNI Multilink Frame Relay Function", RFC 3020, December 2000.
[24] Pate，P.，Lynch，B.和K.Rehbehn，“用于监视和控制UNI/NNI多链路帧中继功能的托管对象的定义”，RFC 3020，2000年12月。
[25] American National Standards Institute, "Coded Identification of Equipment Entities of the North American Telecommunications System for the Purpose of Information Exchange", T1.213-2001.
[25] 美国国家标准协会，“信息交换用北美电信系统设备实体的编码标识”，T1.213-2001。
The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification can be obtained from the IETF Secretariat.
IETF对可能声称与本文件所述技术的实施或使用有关的任何知识产权或其他权利的有效性或范围，或此类权利下的任何许可可能或可能不可用的程度，不采取任何立场；它也不表示它已作出任何努力来确定任何此类权利。有关IETF在标准跟踪和标准相关文件中权利的程序信息，请参见BCP-11。可从IETF秘书处获得可供发布的权利声明副本和任何许可证保证，或本规范实施者或用户试图获得使用此类专有权利的一般许可证或许可的结果。
The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director.
IETF邀请任何相关方提请其注意任何版权、专利或专利申请，或其他可能涉及实施本标准所需技术的专有权利。请将信息发送给IETF执行董事。
Bob Ray PESA Switching Systems, Inc. 330-A Wynn Drive Huntsville, AL 35805 USA
Bob Ray PESA Switching Systems，Inc.美国阿拉巴马州亨茨维尔永利大道330-A号，邮编35805
Phone: +1 256 726 9200 ext. 142
Fax: +1 256 726 9271
EMail: rray@pesa.com
Phone: +1 256 726 9200 ext. 142
Fax: +1 256 726 9271
EMail: rray@pesa.com
Rajesh Abbi Alcatel USA 2912 Wake Forest Road Raleigh, NC 27609-7860 USA
Rajesh Abbi Alcatel USA美国北卡罗来纳州罗利维克森林路2912号，邮编：27609-7860
Phone: +1 919-850-6194
Fax: +1 919-850-6670
EMail: Rajesh.Abbi@alcatel.com
Phone: +1 919-850-6194
Fax: +1 919-850-6670
EMail: Rajesh.Abbi@alcatel.com
Copyright (C) The Internet Society (2002). All Rights Reserved.
版权所有（C）互联网协会（2002年）。版权所有。
This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English.
本文件及其译本可复制并提供给他人，对其进行评论或解释或协助其实施的衍生作品可全部或部分编制、复制、出版和分发，不受任何限制，前提是上述版权声明和本段包含在所有此类副本和衍生作品中。但是，不得以任何方式修改本文件本身，例如删除版权通知或对互联网协会或其他互联网组织的引用，除非出于制定互联网标准的需要，在这种情况下，必须遵循互联网标准过程中定义的版权程序，或根据需要将其翻译成英语以外的其他语言。
The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns.
上述授予的有限许可是永久性的，互联网协会或其继承人或受让人不会撤销。
This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
本文件和其中包含的信息是按“原样”提供的，互联网协会和互联网工程任务组否认所有明示或暗示的保证，包括但不限于任何保证，即使用本文中的信息不会侵犯任何权利，或对适销性或特定用途适用性的任何默示保证。
Acknowledgement
确认
Funding for the RFC Editor function is currently provided by the Internet Society.
RFC编辑功能的资金目前由互联网协会提供。