Network Working Group M. Greene
Request for Comments: 2677 Contractor
Category: Standards Track J. Cucchiara
IronBridge Networks
J. Luciani
Bay Networks
August 1999
Network Working Group M. Greene
Request for Comments: 2677 Contractor
Category: Standards Track J. Cucchiara
IronBridge Networks
J. Luciani
Bay Networks
August 1999
Definitions of Managed Objects for the NBMA Next Hop Resolution Protocol (NHRP)
NBMA下一跳解析协议（NHRP）的托管对象定义
Status of this Memo
本备忘录的状况
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
本文件规定了互联网社区的互联网标准跟踪协议，并要求进行讨论和提出改进建议。有关本协议的标准化状态和状态，请参考当前版本的“互联网官方协议标准”（STD 1）。本备忘录的分发不受限制。
Copyright Notice
版权公告
Copyright (C) The Internet Society (1999). All Rights Reserved.
版权所有（C）互联网协会（1999年）。版权所有。
Abstract
摘要
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for the Next Hop Resolution Protocol (NHRP) as defined in RFC 2332.
此备忘录定义了管理信息库（MIB）的一部分，用于Internet社区中的网络管理协议。特别是，它描述了RFC 2332中定义的下一跳解析协议（NHRP）的托管对象。
Table of Contents
目录
1 Introduction ................................................. 2
2 The SNMP Management Framework ................................ 2
3 Structure of the MIB ......................................... 3
3.1 The NHRP General Group ..................................... 3
3.1.1 The NHRP Cache Table ..................................... 4
3.1.2 The NHRP Purge Request Table ............................. 4
3.2 The NHRP Client Group ...................................... 4
3.2.1 The NHRP Client Table .................................... 4
3.2.2 The NHRP Client Registration Table ....................... 5
3.2.3 The NHRP Client NHS Table ................................ 5
3.2.4 The NHRP Client Statistics Table ......................... 5
3.3 The NHRP Server Group ...................................... 5
3.3.1 The NHRP Server Table .................................... 5
3.3.2 The NHRP Server Cache Table .............................. 5
3.3.3 The NHRP Server NHC Table ................................ 6
1 Introduction ................................................. 2
2 The SNMP Management Framework ................................ 2
3 Structure of the MIB ......................................... 3
3.1 The NHRP General Group ..................................... 3
3.1.1 The NHRP Cache Table ..................................... 4
3.1.2 The NHRP Purge Request Table ............................. 4
3.2 The NHRP Client Group ...................................... 4
3.2.1 The NHRP Client Table .................................... 4
3.2.2 The NHRP Client Registration Table ....................... 5
3.2.3 The NHRP Client NHS Table ................................ 5
3.2.4 The NHRP Client Statistics Table ......................... 5
3.3 The NHRP Server Group ...................................... 5
3.3.1 The NHRP Server Table .................................... 5
3.3.2 The NHRP Server Cache Table .............................. 5
3.3.3 The NHRP Server NHC Table ................................ 6
3.3.4 The NHRP Server Statistics Table ......................... 6
4 NBMA Next Hop Resolution Protocol MIB Definitions ............ 6
5 IANA Considerations .......................................... 62
6 Security ..................................................... 62
7 Intellectual Property ........................................ 63
8 Acknowledgments .............................................. 63
9 References ................................................... 64
10 Authors' Addresses .......................................... 66
11 Full Copyright Statement .................................... 67
3.3.4 The NHRP Server Statistics Table ......................... 6
4 NBMA Next Hop Resolution Protocol MIB Definitions ............ 6
5 IANA Considerations .......................................... 62
6 Security ..................................................... 62
7 Intellectual Property ........................................ 63
8 Acknowledgments .............................................. 63
9 References ................................................... 64
10 Authors' Addresses .......................................... 66
11 Full Copyright Statement .................................... 67
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for the Next Hop Resolution Protocol (NHRP) as defined in RFC 2332 [17].
此备忘录定义了管理信息库（MIB）的一部分，用于Internet社区中的网络管理协议。特别是，它描述了RFC 2332[17]中定义的下一跳解析协议（NHRP）的托管对象。
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [21].
本文件中的关键词“必须”、“不得”、“要求”、“应”、“不应”、“应”、“不应”、“建议”、“可”和“可选”应按照RFC 2119[21]中所述进行解释。
The SNMP Management Framework presently consists of five major components:
SNMP管理框架目前由五个主要组件组成：
o An overall architecture, described in RFC 2571 [1].
o RFC 2571[1]中描述的总体架构。
o Mechanisms for describing and naming objects and events for the purpose of management. The first version of this Structure of Management Information (SMI) is called SMIv1 and described in STD 16, RFC 1155 [2], STD 16, RFC 1212 [3] and RFC 1215 [4]. The second version, called SMIv2, is described in STD 58, RFC 2578 [5], STD 58, RFC 2579 [6] and STD 58, RFC 2580 [7].
o 为管理目的描述和命名对象和事件的机制。这种管理信息结构（SMI）的第一个版本称为SMIv1，并在STD 16、RFC 1155[2]、STD 16、RFC 1212[3]和RFC 1215[4]中进行了描述。第二个版本称为SMIv2，在STD 58、RFC 2578[5]、STD 58、RFC 2579[6]和STD 58、RFC 2580[7]中进行了描述。
o Message protocols for transferring management information. The first version of the SNMP message protocol is called SNMPv1 and described in STD 15, RFC 1157 [8]. A second version of the SNMP message protocol, which is not an Internet standards track protocol, is called SNMPv2c and described in RFC 1901 [9] and RFC 1906 [10]. The third version of the message protocol is called SNMPv3 and described in RFC 1906 [10], RFC 2572 [11] and RFC 2574 [12].
o 用于传输管理信息的消息协议。SNMP消息协议的第一个版本称为SNMPv1，在STD 15、RFC 1157[8]中进行了描述。SNMP消息协议的第二个版本不是互联网标准跟踪协议，称为SNMPv2c，在RFC 1901[9]和RFC 1906[10]中进行了描述。消息协议的第三个版本称为SNMPv3，在RFC 1906[10]、RFC 2572[11]和RFC 2574[12]中进行了描述。
o Protocol operations for accessing management information. The first set of protocol operations and associated PDU formats is described in STD 15, RFC 1157 [8]. A second set of protocol operations and associated PDU formats is described in RFC 1905 [13].
o 访问管理信息的协议操作。STD 15、RFC 1157[8]中描述了第一组协议操作和相关PDU格式。RFC 1905[13]中描述了第二组协议操作和相关PDU格式。
o A set of fundamental applications described in RFC 2573 [14] and the view-based access control mechanism described in RFC 2575 [15].
o RFC 2573[14]中描述的一组基本应用程序和RFC 2575[15]中描述的基于视图的访问控制机制。
A more detailed introduction to the current SNMP Management Framework can be found in RFC 2570 [16].
有关当前SNMP管理框架的更详细介绍，请参见RFC 2570[16]。
Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the mechanisms defined in the SMI.
托管对象通过虚拟信息存储（称为管理信息库或MIB）进行访问。MIB中的对象是使用SMI中定义的机制定义的。
This memo specifies a MIB module that is compliant to the SMIv2. A MIB conforming to the SMIv1 can be produced through the appropriate translations. The resulting translated MIB must be semantically equivalent, except where objects or events are omitted because no translation is possible (use of Counter64). Some machine readable information in SMIv2 will be converted into textual descriptions in SMIv1 during the translation process. However, this loss of machine readable information is not considered to change the semantics of the MIB.
此备忘录指定了符合SMIv2的MIB模块。通过适当的翻译，可以生成符合SMIv1的MIB。生成的已翻译MIB必须在语义上等效，除非由于无法翻译而省略了对象或事件（使用计数器64）。在翻译过程中，SMIv2中的一些机器可读信息将转换为SMIv1中的文本描述。但是，这种机器可读信息的丢失不被认为会改变MIB的语义。
The NHRP MIB contains three groups: the General Group, the Client Group, and the Server Group.
NHRP MIB包含三个组：常规组、客户机组和服务器组。
The General Group contains objects that apply to both clients and servers -- in particular the nhrpNextIndex scalar object, the NHRP Cache Table and the NHRP Purge Request Table.
常规组包含同时应用于客户端和服务器的对象——特别是nhrpNextIndex标量对象、NHRP缓存表和NHRP清除请求表。
The nhrpNextIndex scalar object is used to provide unique indices for the nhprClientIndex in the nhrpClientTable and the nhrpServerIndex in the nhrpServerTable. If used consistently, this object may prevent conflicts when multiple managers attempt to create rows simultaneously in the same table.
nhrpNextIndex标量对象用于为nhrpClientTable中的nhprClientIndex和nhrpServerTable中的nhrpServerIndex提供唯一索引。如果一致使用，当多个管理器试图在同一个表中同时创建行时，此对象可能会防止冲突。
The NHRP Cache Table represents the internetwork layer address to NBMA address cache that is maintained by both NHRP clients and NHRP servers.
NHRP缓存表表示由NHRP客户端和NHRP服务器维护的网络层地址到NBMA地址缓存。
The NHRP Cache Table contains an ifIndex as part of the Index Clause. This ifIndex represents the use of a generic ifIndex, such that the value of this ifIndex SHOULD reflect a specific NBMA subnetwork related interface as determined by an implementation. For example, assuming that the NBMA subnetwork is ATM, then it is up to the implementors of this MIB to determine their own ATM interface layering (assuming compliance with the IF-MIB, RFC 2233 [18] and the ATM-MIB, RFC 2515 [19]). In other words, assuming that the NBMA subnetwork is ATM, the ifIndex in the NHRP Cache Table would represent the ifIndex containing or consisting of the VC (or shortcut) denoted by this Table entry.
NHRP缓存表包含一个ifIndex作为Index子句的一部分。此ifIndex表示通用ifIndex的使用，因此此ifIndex的值应反映由实现确定的特定NBMA子网相关接口。例如，假设NBMA子网为ATM，则由该MIB的实施者确定其自身的ATM接口分层（假设符合IF-MIB、RFC 2233[18]和ATM-MIB、RFC 2515[19]）。换句话说，假设NBMA子网是ATM，NHRP缓存表中的ifIndex将表示包含或由该表项表示的VC（或快捷方式）组成的ifIndex。
The indexing scheme for the NHRP Cache Table is very similar to the MPC Ingress Cache Table and the MPS Ingress Cache Table in the
NHRP缓存表的索引方案与中的MPC入口缓存表和MPS入口缓存表非常相似
Multiprotocol Over ATM (MPOA) MIB [23]. This MIB and the MPOA MIB were designed to be complementary and non-overlapping. The MPOA MIB should also support this MIB. The MPOA MIB was designed prior to this MIB, and was designed by the LANE/MPOA Working Group in the ATM FORUM. The indexing scheme of the NHRP Cache Table (and the NHRP Server Cache Table) reflect the indexing scheme of the MPC Ingress Cache Table and the MPS Ingress Cache Table. Although, other indexing schemes could have been used for the NHRP Cache Table, a consistent indexing scheme between these tables was thought to be more advantageous from an implementation standpoint.
ATM上的多协议（MPOA）MIB[23]。该MIB和MPOA MIB设计为互补且不重叠。MPOA MIB也应支持此MIB。MPOA MIB是在此MIB之前设计的，由LANE/MPOA工作组在ATM论坛上设计。NHRP缓存表（和NHRP服务器缓存表）的索引方案反映了MPC入口缓存表和MPS入口缓存表的索引方案。尽管NHRP缓存表可以使用其他索引方案，但从实现的角度来看，这些表之间的一致索引方案被认为更为有利。
The NHRP Purge Request Table is a way to track Purge Request Information.
NHRP清除请求表是跟踪清除请求信息的一种方法。
The Client Group contains objects that only apply to NHRP clients (NHCs).
客户端组包含仅适用于NHRP客户端（NHC）的对象。
The NHRP Client Table contains entries for NHRP Next Hop Clients (NHCs) associated with this agent. Each row in the table represents a single NHC. The RequestID used in Registration requests needs to be saved to non-volatile storage. Depending upon the implementation,
NHRP客户端表包含与此代理关联的NHRP下一跳客户端（NHC）的条目。表中的每一行代表一个NHC。注册请求中使用的RequestID需要保存到非易失性存储器中。视实施情况而定，
this may or may not impact how the StorageType is used. For a complete description of how the Registration RequestID is used, see Section 5.2.3 of [17].
这可能会也可能不会影响StorageType的使用方式。有关如何使用注册请求ID的完整说明，请参见[17]第5.2.3节。
The NHRP Client Registration Table contains information on registration requests which need to be maintained by the Clients. Each entry in this table represents a single registration request. Note: since the NHRP specification does not mandate a refresh algorithm, this table omits refresh information, however, this table does contain information for all the registration requests which need to be maintained by the NHRP Clients.
NHRP客户端注册表包含客户端需要维护的注册请求信息。此表中的每个条目表示一个注册请求。注意：由于NHRP规范不要求使用刷新算法，因此此表省略了刷新信息，但是，此表确实包含需要由NHRP客户端维护的所有注册请求的信息。
The NHRP Client NHS Table contains the NBMA subnetwork addresses of servers configured for use by the client. By default, the agent will add an entry to this table which corresponds to the client's default router.
NHRP客户端NHS表包含配置供客户端使用的服务器的NBMA子网地址。默认情况下，代理将向该表添加一个条目，该条目对应于客户端的默认路由器。
The NHRP Client Statistics Table contains NHRP statistics maintained by a client. These statistics include counters on requests and replies, as well as counters for errors which are encountered by the Clients.
NHRP客户端统计表包含由客户端维护的NHRP统计信息。这些统计信息包括请求和答复的计数器，以及客户端遇到的错误的计数器。
The Server Group contains objects that only apply to NHRP servers (NHSes).
服务器组包含仅适用于NHRP服务器（NHSE）的对象。
The NHRP Server Table contains entries for each server associated with this agent.
NHRP服务器表包含与此代理关联的每个服务器的条目。
The NHRP Server Cache Table contains additional objects that a server keeps for each entry in its cache. This table extends the NHRP Cache Table defined in the General Group.
NHRP服务器缓存表包含服务器为其缓存中的每个条目保留的附加对象。此表扩展了在常规组中定义的NHRP缓存表。
This table contains information about all the Clients known to the Servers.
此表包含有关服务器已知的所有客户端的信息。
The NHRP Server Statistics Table contains NHRP statistics maintained by a server. These statistics include counters on requests and replies, as well as counters for errors which are encountered by the Servers.
NHRP服务器统计表包含由服务器维护的NHRP统计信息。这些统计信息包括请求和答复的计数器，以及服务器遇到的错误的计数器。
NHRP-MIB DEFINITIONS ::= BEGIN
NHRP-MIB DEFINITIONS ::= BEGIN
IMPORTS
进口
OBJECT-TYPE, MODULE-IDENTITY, mib-2, Integer32, Counter32, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, TruthValue, RowStatus, StorageType, TimeStamp FROM SNMPv2-TC ifIndex FROM IF-MIB AddressFamilyNumbers FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB ;
对象类型、模块标识、mib-2、整数32、计数器32、来自SNMPv2 SMI模块的未签名32、来自SNMPv2 CONF text-CONVENTION的对象组、TruthValue、RowStatus、StorageType、来自SNMPv2 TC的时间戳、来自IF-mib的ifIndex、来自IANA-ADDRESS-FAMILY-NUMBERS-mib的家庭编号；
nhrpMIB MODULE-IDENTITY LAST-UPDATED "9908260000Z" -- August 26, 1999 ORGANIZATION "Internetworking Over NBMA (ion) Working Group" CONTACT-INFO "Maria Greene (maria@xedia.com) Contractor
nhrpMIB模块标识最后更新“990826000Z”-1999年8月26日组织“NBMA（离子）工作组互联”联系方式“Maria Greene(maria@xedia.com)承包人
Joan Cucchiara (joan@ironbridgenetworks.com) IronBridge Networks
琼·库奇亚拉(joan@ironbridgenetworks.com)铁桥网络
James V. Luciani (luciani@baynetworks.com) Bay Networks"
詹姆斯诉卢西亚尼(luciani@baynetworks.com)海湾网络”
DESCRIPTION "This MIB contains managed object definitions for the Next Hop Resolution Procol, NHRP, as defined in RFC 2332 [17]."
DESCRIPTION“此MIB包含RFC 2332[17]中定义的下一跳解析过程NHRP的托管对象定义。”
-- revision history
--修订历史
REVISION "9908260000Z" -- August 26, 1999 DESCRIPTION "Initial version, published as RFC 2677."
修订版“990826000Z”-1999年8月26日描述“初始版本，作为RFC 2677出版。”
::= { mib-2 71 }
::= { mib-2 71 }
--****************************************************************
-- NHRP Textual Conventions
--****************************************************************
--****************************************************************
-- NHRP Textual Conventions
--****************************************************************
NhrpGenAddr ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of an internetwork layer or NBMA address."
SYNTAX OCTET STRING (SIZE (0..64))
NhrpGenAddr ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of an internetwork layer or NBMA address."
SYNTAX OCTET STRING (SIZE (0..64))
nhrpObjects OBJECT IDENTIFIER ::= { nhrpMIB 1 }
nhrpObjects OBJECT IDENTIFIER ::= { nhrpMIB 1 }
--****************************************************************
-- NHRP General (Client and Server) Objects
--****************************************************************
--****************************************************************
-- NHRP General (Client and Server) Objects
--****************************************************************
nhrpGeneralObjects OBJECT IDENTIFIER ::= { nhrpObjects 1 }
nhrpGeneralObjects OBJECT IDENTIFIER ::= { nhrpObjects 1 }
--
-- The following scalar is to be used to
-- provided indices for the
-- nhrpClientTable, and/or the nhrpServerTable.
--
--
-- The following scalar is to be used to
-- provided indices for the
-- nhrpClientTable, and/or the nhrpServerTable.
--
nhrpNextIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This scalar is used for creating rows in the nhrpClientTable and the nhrpServerTable. The value of this variable is a currently unused value for nhrpClientIndex and nhrpServerIndex.
nhrpNextIndex对象类型语法Unsigned32 MAX-ACCESS只读状态当前描述“此标量用于在nhrpClientTable和nhrpServerTable中创建行。此变量的值是nhrpClientIndex和nhrpServerIndex当前未使用的值。
The value returned when reading this variable must be unique for the NHC's and NHS's indices associated with this row. Subsequent attempts to read this variable must return different values.
读取此变量时返回的值对于与此行关联的NHC和NHS索引必须是唯一的。后续读取此变量的尝试必须返回不同的值。
NOTE: this object exists in the General Group because it is to be used in establishing rows in the nhrpClientTable and the nhrpServerTable. In other words, the value retrieved from this object could become the value of nhrpClientIndex and nhprServerIndex.
注意：此对象存在于常规组中，因为它用于在nhrpClientTable和nhrpServerTable中建立行。换句话说，从该对象检索到的值可以成为nhrpClientIndex和nhprServerIndex的值。
In the situation of an agent re-initialization the value of this object must be saved in non-volatile storage.
在代理重新初始化的情况下，此对象的值必须保存在非易失性存储器中。
This variable will return the special value 0 if no new
rows can be created."
::= { nhrpGeneralObjects 1 }
This variable will return the special value 0 if no new
rows can be created."
::= { nhrpGeneralObjects 1 }
-- -- The NHRP Cache Table --
----NHRP缓存表--
nhrpCacheTable OBJECT-TYPE SYNTAX SEQUENCE OF NhrpCacheEntry MAX-ACCESS not-accessible STATUS current
NhrpCacheEntry MAX-ACCESS的nhrpCacheTable对象类型语法序列不可访问状态当前
DESCRIPTION
"This table contains mappings between internetwork layer
addresses and NBMA subnetwork layer addresses."
::= { nhrpGeneralObjects 2 }
DESCRIPTION
"This table contains mappings between internetwork layer
addresses and NBMA subnetwork layer addresses."
::= { nhrpGeneralObjects 2 }
nhrpCacheEntry OBJECT-TYPE SYNTAX NhrpCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A cached mapping between an internetwork layer address and an NBMA address. Entries can be created by the network administrator using the nhrpCacheRowStatus column, or they may be added dynamically based on protocol operation (including NHRP, SCSP, and others, such as ATMARP).
nhrpCacheEntry对象类型语法nhrpCacheEntry MAX-ACCESS不可访问状态当前描述“Internet层地址和NBMA地址之间的缓存映射。网络管理员可以使用nhrpCacheRowStatus列创建条目，也可以根据协议操作动态添加条目（包括NHRP、SCSP和其他，如ATMARP）。
When created based by NHRP protocol operations this entry is largely based on contents contained in the Client Information Entry (CIE).
当根据NHRP协议操作创建时，此条目主要基于客户端信息条目（CIE）中包含的内容。
Zero or more Client Information Entries (CIEs) may be
included in the NHRP Packet. For a complete description
of the CIE, refer to Section 5.2.0.1 of
RFC 2332 [17]."
INDEX {
nhrpCacheInternetworkAddrType,
nhrpCacheInternetworkAddr,
ifIndex,
nhrpCacheIndex
}
::= { nhrpCacheTable 1 }
Zero or more Client Information Entries (CIEs) may be
included in the NHRP Packet. For a complete description
of the CIE, refer to Section 5.2.0.1 of
RFC 2332 [17]."
INDEX {
nhrpCacheInternetworkAddrType,
nhrpCacheInternetworkAddr,
ifIndex,
nhrpCacheIndex
}
::= { nhrpCacheTable 1 }
NhrpCacheEntry ::= SEQUENCE {
nhrpCacheInternetworkAddrType AddressFamilyNumbers,
nhrpCacheInternetworkAddr NhrpGenAddr,
nhrpCacheIndex Unsigned32,
nhrpCachePrefixLength Integer32,
nhrpCacheNextHopInternetworkAddr NhrpGenAddr,
nhrpCacheNbmaAddrType AddressFamilyNumbers,
nhrpCacheNbmaAddr NhrpGenAddr,
nhrpCacheNbmaSubaddr NhrpGenAddr,
nhrpCacheType INTEGER,
nhrpCacheState INTEGER,
nhrpCacheHoldingTimeValid TruthValue,
nhrpCacheHoldingTime Unsigned32,
nhrpCacheNegotiatedMtu Integer32,
nhrpCachePreference Integer32,
nhrpCacheStorageType StorageType,
nhrpCacheRowStatus RowStatus
NhrpCacheEntry ::= SEQUENCE {
nhrpCacheInternetworkAddrType AddressFamilyNumbers,
nhrpCacheInternetworkAddr NhrpGenAddr,
nhrpCacheIndex Unsigned32,
nhrpCachePrefixLength Integer32,
nhrpCacheNextHopInternetworkAddr NhrpGenAddr,
nhrpCacheNbmaAddrType AddressFamilyNumbers,
nhrpCacheNbmaAddr NhrpGenAddr,
nhrpCacheNbmaSubaddr NhrpGenAddr,
nhrpCacheType INTEGER,
nhrpCacheState INTEGER,
nhrpCacheHoldingTimeValid TruthValue,
nhrpCacheHoldingTime Unsigned32,
nhrpCacheNegotiatedMtu Integer32,
nhrpCachePreference Integer32,
nhrpCacheStorageType StorageType,
nhrpCacheRowStatus RowStatus
}
}
nhrpCacheInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The internetwork layer address type of this Next Hop
Resolution Cache entry. The value of this object indicates
how to interpret the values of nhrpCacheInternetworkAddr
and nhrpCacheNextHopInternetworkAddr."
::= { nhrpCacheEntry 1 }
nhrpCacheInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The internetwork layer address type of this Next Hop
Resolution Cache entry. The value of this object indicates
how to interpret the values of nhrpCacheInternetworkAddr
and nhrpCacheNextHopInternetworkAddr."
::= { nhrpCacheEntry 1 }
nhrpCacheInternetworkAddr OBJECT-TYPE SYNTAX NhrpGenAddr MAX-ACCESS not-accessible STATUS current
nhrpCacheInternetworkAddr对象类型语法NhrpGenAddr MAX-ACCESS不可访问状态当前
DESCRIPTION
"The value of the internetwork address of the
destination."
::= { nhrpCacheEntry 2 }
DESCRIPTION
"The value of the internetwork address of the
destination."
::= { nhrpCacheEntry 2 }
nhrpCacheIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for this entry that has local
significance within the scope of the General
Group. This identifier is used here to
uniquely identify this row, and also used
in the 'nhrpPurgeTable' for the value of
the 'nhrpPurgeCacheIdentifier'."
::= { nhrpCacheEntry 3 }
nhrpCacheIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for this entry that has local
significance within the scope of the General
Group. This identifier is used here to
uniquely identify this row, and also used
in the 'nhrpPurgeTable' for the value of
the 'nhrpPurgeCacheIdentifier'."
::= { nhrpCacheEntry 3 }
nhrpCachePrefixLength OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of bits that define the internetwork layer
prefix associated with the nhrpCacheInternetworkAddr."
::= { nhrpCacheEntry 4 }
nhrpCachePrefixLength OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of bits that define the internetwork layer
prefix associated with the nhrpCacheInternetworkAddr."
::= { nhrpCacheEntry 4 }
nhrpCacheNextHopInternetworkAddr OBJECT-TYPE SYNTAX NhrpGenAddr MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the internetwork address of the next hop."
nhrpCacheNextHopInternetworkAddr对象类型语法NhrpGenAddr MAX-ACCESS read create STATUS current DESCRIPTION“下一个跃点的网络地址的值。”
::= { nhrpCacheEntry 5 }
::= { nhrpCacheEntry 5 }
nhrpCacheNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA address type. The value of this
object indicates how to interpret
the values of nhrpCacheNbmaAddr and
nhrpCacheNbmaSubaddr."
::= { nhrpCacheEntry 6 }
nhrpCacheNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA address type. The value of this
object indicates how to interpret
the values of nhrpCacheNbmaAddr and
nhrpCacheNbmaSubaddr."
::= { nhrpCacheEntry 6 }
nhrpCacheNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the NBMA subnetwork address of the next
hop."
::= { nhrpCacheEntry 7 }
nhrpCacheNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the NBMA subnetwork address of the next
hop."
::= { nhrpCacheEntry 7 }
nhrpCacheNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the NBMA subaddress of the next hop. If
there is no subaddress concept for the NBMA address
family, this value will be a zero-length OCTET STRING."
::= { nhrpCacheEntry 8 }
nhrpCacheNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the NBMA subaddress of the next hop. If
there is no subaddress concept for the NBMA address
family, this value will be a zero-length OCTET STRING."
::= { nhrpCacheEntry 8 }
nhrpCacheType OBJECT-TYPE
SYNTAX INTEGER {
other(1),
register(2),
resolveAuthoritative(3),
resoveNonauthoritative(4),
transit(5),
administrativelyAdded(6),
atmarp(7),
scsp(8)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An indication of how this cache entry
was created. The values are:
nhrpCacheType OBJECT-TYPE
SYNTAX INTEGER {
other(1),
register(2),
resolveAuthoritative(3),
resoveNonauthoritative(4),
transit(5),
administrativelyAdded(6),
atmarp(7),
scsp(8)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An indication of how this cache entry
was created. The values are:
'other(1)' The entry was added by some other means.
“其他（1）”该条目是通过其他方式添加的。
'register(2)' In a server, added based on a client registration.
服务器中的“注册（2）”，基于客户端注册添加。
'resolveAuthoritative(3)' In a client, added based on receiving an Authoritative NHRP Resolution Reply.
客户端中的“ResolveAuthority（3）”，基于收到权威NHRP解决方案回复而添加。
'resolveNonauthoritative(4)' In a client, added based on receiving a Nonauthoritative NHRP Resolution Reply.
客户端中的“ResolveNonAuthoritive（4）”，基于收到非授权NHRP解决方案回复而添加。
'transit(5)' In a transit server, added by examining a forwarded NHRP packet.
传输服务器中的“传输（5）”，通过检查转发的NHRP数据包添加。
'administrativelyAdded(6)' In a client or server, manually added by the administrator. The StorageType of this entry is reflected in 'nhrpCacheStorageType'.
在客户端或服务器中添加“AdministrativeAdded（6）”，由管理员手动添加。此条目的StorageType反映在“nhrpCacheStorageType”中。
'atmarp(7)' The entry was added due to an ATMARP.
“atmarp（7）”由于atmarp而添加的条目。
'scsp(8)' The entry was added due to SCSP.
“scsp（8）”由于scsp而添加的条目。
When the entry is under creation using the nhrpCacheRowStatus column, the only value that can be specified by the administrator is 'administrativelyAdded'. Attempting to set any other value will cause an 'inconsistentValue' error.
当使用nhrpCacheRowStatus列创建条目时，管理员可以指定的唯一值是“AdministrativeAdded”。尝试设置任何其他值将导致“值不一致”错误。
The value cannot be modified once the entry is active."
::= { nhrpCacheEntry 9 }
The value cannot be modified once the entry is active."
::= { nhrpCacheEntry 9 }
nhrpCacheState OBJECT-TYPE
SYNTAX INTEGER {
incomplete(1),
ackReply(2),
nakReply(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
nhrpCacheState OBJECT-TYPE
SYNTAX INTEGER {
incomplete(1),
ackReply(2),
nakReply(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of the state of this entry. The values are:
“此条目状态的指示。值为：
'incomplete(1)' The client has sent a NHRP Resolution Request but has not yet received the NHRP Resolution Reply.
“不完整（1）”客户已发送NHRP解决请求，但尚未收到NHRP解决回复。
'ackReply(2)' For a client or server, this is a cached valid mapping.
“ackReply（2）”对于客户端或服务器，这是缓存的有效映射。
'nakReply(3)' For a client or server, this is a
cached NAK mapping."
::= { nhrpCacheEntry 10 }
'nakReply(3)' For a client or server, this is a
cached NAK mapping."
::= { nhrpCacheEntry 10 }
nhrpCacheHoldingTimeValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True(1) is returned if the value of 'nhrpCacheType' is not 'administrativelyAdded'. Since the value of 'nhrpCacheType' was not configured by a user, the value of 'nhrpCacheHoldingTime' is considered valid. In other words, the value of 'nhrpCacheHoldingTime' represents the Holding Time for the cache Entry.
nhrpCacheHoldingTimeValid对象类型语法TruthValue MAX-ACCESS只读状态当前描述“True（1）如果“nhrpCacheType”的值不是“AdministrativeAdded”，则返回。由于“nhrpCacheType”的值不是由用户配置的，因此“nhrpCacheHoldingTime”的值被视为有效。换句话说，“nhrpCacheHoldingTime”的值表示缓存项的保留时间。
If 'nhrpCacheType has been configured by a
user, (i.e. the value of 'nhrpCacheType' is
'administrativelyAdded') then false(2) will be returned.
This indicates that the value of
'nhrpCacheHoldingTime' is undefined because this row
could possibly be backed up in nonvolatile storage."
::= { nhrpCacheEntry 11 }
If 'nhrpCacheType has been configured by a
user, (i.e. the value of 'nhrpCacheType' is
'administrativelyAdded') then false(2) will be returned.
This indicates that the value of
'nhrpCacheHoldingTime' is undefined because this row
could possibly be backed up in nonvolatile storage."
::= { nhrpCacheEntry 11 }
nhrpCacheHoldingTime OBJECT-TYPE SYNTAX Unsigned32(0..65535) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "If the value of 'nhrpCacheHoldingTimeValid is true(1) then this object represents the number of seconds that the cache entry will remain in this table. When this value reaches 0 (zero) the row should be deleted.
nhrpCacheHoldingTime对象类型语法Unsigned32（0..65535）单位“秒”最大访问只读状态当前描述“如果'nhrpCacheHoldingTimeValid'的值为真（1），则此对象表示缓存项将保留在此表中的秒数。当此值达到0（零）时，应删除该行。
If the value of 'nhrpCacheHoldingTimeValid is
false(2) then this object is undefined."
::= { nhrpCacheEntry 12 }
If the value of 'nhrpCacheHoldingTimeValid is
false(2) then this object is undefined."
::= { nhrpCacheEntry 12 }
nhrpCacheNegotiatedMtu OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum transmission unit (MTU) that was negotiated
or registered for this entity. In other words, this is the
actual MTU being used."
::= { nhrpCacheEntry 13 }
nhrpCacheNegotiatedMtu OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum transmission unit (MTU) that was negotiated
or registered for this entity. In other words, this is the
actual MTU being used."
::= { nhrpCacheEntry 13 }
nhrpCachePreference OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "An object which reflects the Preference value of the Client Information Entry (CIE).
nhrpCachePreference对象类型语法整数32（0..255）MAX-ACCESS read create STATUS current DESCRIPTION“反映客户端信息项（CIE）首选项值的对象。
Zero or more Client Information Entries (CIEs) may be
included in the NHRP Packet. One of the fields in the
CIE is the Preference. For a complete description of
the CIE, refer to Section 5.2.0.1 of RFC 2332 [17]."
REFERENCE
"Section 5.2.0.1 Mandatory Part Format, RFC 2332 [17]."
::= { nhrpCacheEntry 14 }
Zero or more Client Information Entries (CIEs) may be
included in the NHRP Packet. One of the fields in the
CIE is the Preference. For a complete description of
the CIE, refer to Section 5.2.0.1 of RFC 2332 [17]."
REFERENCE
"Section 5.2.0.1 Mandatory Part Format, RFC 2332 [17]."
::= { nhrpCacheEntry 14 }
nhrpCacheStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This value only has meaning when the 'nhrpCacheType' has the value of 'administrativelyAdded'.
nhrpCacheStorageType对象类型语法StorageType MAX-ACCESS读取创建状态当前描述“仅当“nhrpCacheType”的值为“administrativelyAdded”时，此值才有意义。
When the row is created due to being 'administrativelyAdded', this object reflects whether this row is kept in volatile storage and lost upon reboot or if this row is backed up by non-volatile or permanent storage.
由于“管理性添加”而创建行时，此对象反映该行是否保存在易失性存储中并在重新启动时丢失，或者该行是否由非易失性或永久性存储备份。
If the value of 'nhrpCacheType' has a value which
is not 'administrativelyAdded, then the value of this
object is 'other(1)'."
DEFVAL { nonVolatile }
::= { nhrpCacheEntry 15 }
If the value of 'nhrpCacheType' has a value which
is not 'administrativelyAdded, then the value of this
object is 'other(1)'."
DEFVAL { nonVolatile }
::= { nhrpCacheEntry 15 }
nhrpCacheRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpCacheEntry 16 }
nhrpCacheRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpCacheEntry 16 }
-- -- The NHRP Purge Request Table --
----NHRP净化请求表--
nhrpPurgeReqTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpPurgeReqEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table will track Purge Request Information."
::= { nhrpGeneralObjects 3 }
nhrpPurgeReqTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpPurgeReqEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table will track Purge Request Information."
::= { nhrpGeneralObjects 3 }
nhrpPurgeReqEntry OBJECT-TYPE
SYNTAX NhrpPurgeReqEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information regarding a Purge Request."
INDEX { nhrpPurgeIndex }
::= { nhrpPurgeReqTable 1 }
nhrpPurgeReqEntry OBJECT-TYPE
SYNTAX NhrpPurgeReqEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information regarding a Purge Request."
INDEX { nhrpPurgeIndex }
::= { nhrpPurgeReqTable 1 }
NhrpPurgeReqEntry ::= SEQUENCE {
nhrpPurgeIndex Unsigned32,
nhrpPurgeCacheIdentifier Unsigned32,
nhrpPurgePrefixLength Integer32,
nhrpPurgeRequestID Unsigned32,
nhrpPurgeReplyExpected TruthValue,
nhrpPurgeRowStatus RowStatus
}
NhrpPurgeReqEntry ::= SEQUENCE {
nhrpPurgeIndex Unsigned32,
nhrpPurgeCacheIdentifier Unsigned32,
nhrpPurgePrefixLength Integer32,
nhrpPurgeRequestID Unsigned32,
nhrpPurgeReplyExpected TruthValue,
nhrpPurgeRowStatus RowStatus
}
nhrpPurgeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index for this entry that has local significance
within the scope of this table."
::= { nhrpPurgeReqEntry 1 }
nhrpPurgeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index for this entry that has local significance
within the scope of this table."
::= { nhrpPurgeReqEntry 1 }
nhrpPurgeCacheIdentifier OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-create STATUS current
nhrpPurgeCacheIdentifier对象类型语法Unsigned32（1..4294967295）MAX-ACCESS读取创建状态当前
DESCRIPTION
"This object identifies which row in
'nhrpCacheTable' is being purged. This object
should have the same value as the 'nhrpCacheIndex'
in the 'nhrpCacheTable'."
::= { nhrpPurgeReqEntry 2 }
DESCRIPTION
"This object identifies which row in
'nhrpCacheTable' is being purged. This object
should have the same value as the 'nhrpCacheIndex'
in the 'nhrpCacheTable'."
::= { nhrpPurgeReqEntry 2 }
nhrpPurgePrefixLength OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"In the case of NHRP Purge Requests, this specifies the
equivalence class of addresses which match the first
'Prefix Length' bit positions of the Client Protocol
Address specified in the Client Information Entry (CIE)."
::= { nhrpPurgeReqEntry 3 }
nhrpPurgePrefixLength OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"In the case of NHRP Purge Requests, this specifies the
equivalence class of addresses which match the first
'Prefix Length' bit positions of the Client Protocol
Address specified in the Client Information Entry (CIE)."
::= { nhrpPurgeReqEntry 3 }
nhrpPurgeRequestID OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Request ID used in the purge request."
::= { nhrpPurgeReqEntry 4 }
nhrpPurgeRequestID OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Request ID used in the purge request."
::= { nhrpPurgeReqEntry 4 }
nhrpPurgeReplyExpected OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An indication of whether this Purge Request has the
'N' Bit cleared (off)."
::= { nhrpPurgeReqEntry 5 }
nhrpPurgeReplyExpected OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An indication of whether this Purge Request has the
'N' Bit cleared (off)."
::= { nhrpPurgeReqEntry 5 }
nhrpPurgeRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpPurgeReqEntry 6 }
nhrpPurgeRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpPurgeReqEntry 6 }
--****************************************************************
-- NHRP Client Objects
--****************************************************************
--****************************************************************
-- NHRP Client Objects
--****************************************************************
nhrpClientObjects OBJECT IDENTIFIER ::= { nhrpObjects 2 }
nhrpClientObjects OBJECT IDENTIFIER ::= { nhrpObjects 2 }
-- -- The NHRP Client Table --
----NHRP客户机表--
nhrpClientTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about NHRP clients (NHCs) managed by this
agent."
::= { nhrpClientObjects 1 }
nhrpClientTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about NHRP clients (NHCs) managed by this
agent."
::= { nhrpClientObjects 1 }
nhrpClientEntry OBJECT-TYPE
SYNTAX NhrpClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single NHC."
INDEX { nhrpClientIndex }
::= { nhrpClientTable 1 }
nhrpClientEntry OBJECT-TYPE
SYNTAX NhrpClientEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single NHC."
INDEX { nhrpClientIndex }
::= { nhrpClientTable 1 }
NhrpClientEntry ::= SEQUENCE {
nhrpClientIndex Unsigned32,
nhrpClientInternetworkAddrType AddressFamilyNumbers,
nhrpClientInternetworkAddr NhrpGenAddr,
nhrpClientNbmaAddrType AddressFamilyNumbers,
nhrpClientNbmaAddr NhrpGenAddr,
nhrpClientNbmaSubaddr NhrpGenAddr,
nhrpClientInitialRequestTimeout Integer32,
nhrpClientRegistrationRequestRetries Integer32,
nhrpClientResolutionRequestRetries Integer32,
nhrpClientPurgeRequestRetries Integer32,
nhrpClientDefaultMtu Unsigned32,
nhrpClientHoldTime Unsigned32,
nhrpClientRequestID Unsigned32,
nhrpClientStorageType StorageType,
nhrpClientRowStatus RowStatus
}
NhrpClientEntry ::= SEQUENCE {
nhrpClientIndex Unsigned32,
nhrpClientInternetworkAddrType AddressFamilyNumbers,
nhrpClientInternetworkAddr NhrpGenAddr,
nhrpClientNbmaAddrType AddressFamilyNumbers,
nhrpClientNbmaAddr NhrpGenAddr,
nhrpClientNbmaSubaddr NhrpGenAddr,
nhrpClientInitialRequestTimeout Integer32,
nhrpClientRegistrationRequestRetries Integer32,
nhrpClientResolutionRequestRetries Integer32,
nhrpClientPurgeRequestRetries Integer32,
nhrpClientDefaultMtu Unsigned32,
nhrpClientHoldTime Unsigned32,
nhrpClientRequestID Unsigned32,
nhrpClientStorageType StorageType,
nhrpClientRowStatus RowStatus
}
nhrpClientIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An identifier for the NHRP client that is unique within the scope of this agent. The 'nhrpNextIndex' value should be consulted (read), prior to creating a row in this table, and the value returned from reading 'nhrpNextIndex' should be used as this object's value."
nhrpClientIndex对象类型语法Unsigned32（1..4294967295）MAX-ACCESS不可访问状态当前描述“此代理范围内唯一的NHRP客户端标识符。应参考“nhrpNextIndex”值（读取），然后再在此表中创建行，并且读取'nhrpNextIndex'返回的值应用作此对象的值。“
::= { nhrpClientEntry 1 }
::= { nhrpClientEntry 1 }
nhrpClientInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of this
client. This object indicates how the value of
nhrpClientInternetworkAddr is to be interpreted."
::= { nhrpClientEntry 2 }
nhrpClientInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of this
client. This object indicates how the value of
nhrpClientInternetworkAddr is to be interpreted."
::= { nhrpClientEntry 2 }
nhrpClientInternetworkAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork layer address of this
client."
::= { nhrpClientEntry 3 }
nhrpClientInternetworkAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork layer address of this
client."
::= { nhrpClientEntry 3 }
nhrpClientNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the NBMA subnetwork address of this client.
This object indicates how the values of
nhrpClientNbmaAddr and nhrpClientNbmaSubaddr are to be
interpreted."
::= { nhrpClientEntry 4 }
nhrpClientNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the NBMA subnetwork address of this client.
This object indicates how the values of
nhrpClientNbmaAddr and nhrpClientNbmaSubaddr are to be
interpreted."
::= { nhrpClientEntry 4 }
nhrpClientNbmaAddr OBJECT-TYPE SYNTAX NhrpGenAddr MAX-ACCESS read-create STATUS current
nhrpClientNbmaAddr对象类型语法NhrpGenAddr MAX-ACCESS read create STATUS current
DESCRIPTION
"The NBMA subnetwork address of this client."
::= { nhrpClientEntry 5 }
DESCRIPTION
"The NBMA subnetwork address of this client."
::= { nhrpClientEntry 5 }
nhrpClientNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA subaddress of this client. For NBMA address
families without a subaddress concept, this will be a
zero-length OCTET STRING."
::= { nhrpClientEntry 6 }
nhrpClientNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA subaddress of this client. For NBMA address
families without a subaddress concept, this will be a
zero-length OCTET STRING."
::= { nhrpClientEntry 6 }
nhrpClientInitialRequestTimeout OBJECT-TYPE
SYNTAX Integer32 (1..900)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds that the client will wait before
timing out an NHRP initial request. This object only has
meaning for the initial timeout period."
DEFVAL { 10 }
::= { nhrpClientEntry 7 }
nhrpClientInitialRequestTimeout OBJECT-TYPE
SYNTAX Integer32 (1..900)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds that the client will wait before
timing out an NHRP initial request. This object only has
meaning for the initial timeout period."
DEFVAL { 10 }
::= { nhrpClientEntry 7 }
nhrpClientRegistrationRequestRetries OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of times the client will retry the
registration request before failure. A value of
0 means don't retry. A value of 65535 means
retry forever."
DEFVAL { 3 }
::= { nhrpClientEntry 8 }
nhrpClientRegistrationRequestRetries OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of times the client will retry the
registration request before failure. A value of
0 means don't retry. A value of 65535 means
retry forever."
DEFVAL { 3 }
::= { nhrpClientEntry 8 }
nhrpClientResolutionRequestRetries OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of times the client will retry the resolution
request before failure. A value of 0 means don't retry.
A value of 65535 means retry forever."
DEFVAL { 3 }
::= { nhrpClientEntry 9 }
nhrpClientResolutionRequestRetries OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of times the client will retry the resolution
request before failure. A value of 0 means don't retry.
A value of 65535 means retry forever."
DEFVAL { 3 }
::= { nhrpClientEntry 9 }
nhrpClientPurgeRequestRetries OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of times the client will retry a purge request
before failure. A value of 0 means don't retry. A value of
65535 means retry forever."
DEFVAL { 3 }
::= { nhrpClientEntry 10 }
nhrpClientPurgeRequestRetries OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of times the client will retry a purge request
before failure. A value of 0 means don't retry. A value of
65535 means retry forever."
DEFVAL { 3 }
::= { nhrpClientEntry 10 }
nhrpClientDefaultMtu OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-create STATUS current
nhrpClientDefaultMtu对象类型语法Unsigned32（0..65535）MAX-ACCESS读取创建状态当前
DESCRIPTION
"The default maximum transmission unit (MTU) of the
LIS/LAG which this client should use. This object
will be initialized by the agent to the default MTU
of the LIS/LAG (which is 9180) unless a different MTU
value is specified during creation of this Client."
REFERENCE
"RFC 2225 [25], Classical IP and ARP over ATM, Section 7,
DEFAULT VALUE FOR IP MTU OVER ATM AAL5."
DEFVAL { 9180 }
::= { nhrpClientEntry 11 }
DESCRIPTION
"The default maximum transmission unit (MTU) of the
LIS/LAG which this client should use. This object
will be initialized by the agent to the default MTU
of the LIS/LAG (which is 9180) unless a different MTU
value is specified during creation of this Client."
REFERENCE
"RFC 2225 [25], Classical IP and ARP over ATM, Section 7,
DEFAULT VALUE FOR IP MTU OVER ATM AAL5."
DEFVAL { 9180 }
::= { nhrpClientEntry 11 }
nhrpClientHoldTime OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The hold time the client will register."
DEFVAL { 900 }
::= { nhrpClientEntry 12 }
nhrpClientHoldTime OBJECT-TYPE
SYNTAX Unsigned32(0..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The hold time the client will register."
DEFVAL { 900 }
::= { nhrpClientEntry 12 }
nhrpClientRequestID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The Request ID used to register this client with its server. According to Section 5.2.3 of the NHRP Specification, RFC 2332 [17], the Request ID must be kept in non-volatile storage, so that if an NHC crashes and re-initializes, it will use a different
nhrpClientRequestID对象类型语法Unsigned32 MAX-ACCESS read create STATUS current DESCRIPTION“用于向其服务器注册此客户端的请求ID。根据NHRP规范第5.2.3节，RFC 2332[17]，请求ID必须保存在非易失性存储器中，这样，如果NHC崩溃并重新初始化，它将使用不同的
Request ID during the registration process
when reregistering with the same NHS."
REFERENCE
"Section 5.2.3 NHRP Registration Request, RFC 2332 [17]."
::= { nhrpClientEntry 13 }
Request ID during the registration process
when reregistering with the same NHS."
REFERENCE
"Section 5.2.3 NHRP Registration Request, RFC 2332 [17]."
::= { nhrpClientEntry 13 }
nhrpClientStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object defines whether this row is kept in
volatile storage and lost upon a Client crash or
reboot situation, or if this row is backed up by
nonvolatile or permanent storage."
DEFVAL { nonVolatile }
::= { nhrpClientEntry 14 }
nhrpClientStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object defines whether this row is kept in
volatile storage and lost upon a Client crash or
reboot situation, or if this row is backed up by
nonvolatile or permanent storage."
DEFVAL { nonVolatile }
::= { nhrpClientEntry 14 }
nhrpClientRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpClientEntry 15 }
nhrpClientRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpClientEntry 15 }
-- -- The NHRP Client Registration Table --
----NHRP客户端注册表--
nhrpClientRegistrationTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpClientRegistrationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Registration Request Information that
needs to be maintained by the NHCs (clients)."
REFERENCE
"Section 5.2.3 NHRP Registration Request, RFC 2332 [17]."
::= { nhrpClientObjects 2 }
nhrpClientRegistrationTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpClientRegistrationEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Registration Request Information that
needs to be maintained by the NHCs (clients)."
REFERENCE
"Section 5.2.3 NHRP Registration Request, RFC 2332 [17]."
::= { nhrpClientObjects 2 }
nhrpClientRegistrationEntry OBJECT-TYPE SYNTAX NhrpClientRegistrationEntry MAX-ACCESS not-accessible STATUS current
nhrpClientRegistrationEntry对象类型语法nhrpClientRegistrationEntry MAX-ACCESS不可访问状态当前
DESCRIPTION
"An NHC needs to maintain registration request information
between the NHC and the NHS. An entry in this table
represents information for a single registration request."
INDEX { nhrpClientIndex,
nhrpClientRegIndex
}
::= { nhrpClientRegistrationTable 1 }
DESCRIPTION
"An NHC needs to maintain registration request information
between the NHC and the NHS. An entry in this table
represents information for a single registration request."
INDEX { nhrpClientIndex,
nhrpClientRegIndex
}
::= { nhrpClientRegistrationTable 1 }
NhrpClientRegistrationEntry ::= SEQUENCE {
nhrpClientRegIndex Unsigned32,
nhrpClientRegUniqueness INTEGER,
nhrpClientRegState INTEGER,
nhrpClientRegRowStatus RowStatus
}
NhrpClientRegistrationEntry ::= SEQUENCE {
nhrpClientRegIndex Unsigned32,
nhrpClientRegUniqueness INTEGER,
nhrpClientRegState INTEGER,
nhrpClientRegRowStatus RowStatus
}
nhrpClientRegIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION
NHRPCLIEntergindex对象类型语法Unsigned32（1..4294967295）MAX-ACCESS不可访问状态当前说明
"An identifier for this entry such that it
identifies a specific Registration Request from
the NHC represented by the nhrpClientIndex."
::= { nhrpClientRegistrationEntry 1 }
"An identifier for this entry such that it
identifies a specific Registration Request from
the NHC represented by the nhrpClientIndex."
::= { nhrpClientRegistrationEntry 1 }
nhrpClientRegUniqueness OBJECT-TYPE
SYNTAX INTEGER {
requestUnique(1),
requestNotUnique(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Uniqueness indicator for this Registration Request.
If this object has the value of requestUnique(1), then
the Uniqueness bit is set in the the NHRP Registration
Request represented by this row. The value cannot
be changed once the row is created."
::= { nhrpClientRegistrationEntry 2 }
nhrpClientRegUniqueness OBJECT-TYPE
SYNTAX INTEGER {
requestUnique(1),
requestNotUnique(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Uniqueness indicator for this Registration Request.
If this object has the value of requestUnique(1), then
the Uniqueness bit is set in the the NHRP Registration
Request represented by this row. The value cannot
be changed once the row is created."
::= { nhrpClientRegistrationEntry 2 }
nhrpClientRegState OBJECT-TYPE SYNTAX INTEGER { other(1), registering(2), ackRegisterReply(3), nakRegisterReply(4)
nhrpClientRegState对象类型语法整数{other（1），registing（2），ackRegisterReply（3），nakrregisterreply（4）
} MAX-ACCESS read-only STATUS current DESCRIPTION "The registration state of this client. The values are: 'other(1)' The state of the registration request is not one of 'registering', 'ackRegisterReply' or 'nakRegisterReply'.
}MAX-ACCESS只读状态当前描述“此客户端的注册状态。值为：'其他（1）'注册请求的状态不是'Registing'、'ackRegisterReply'或'nakRegisterReply'之一。
'registering(2)' A registration request has been issued and a registration reply is expected.
“注册（2）”已发出注册请求，预计会收到注册回复。
'ackRegisterReply(3)' A positive registration reply has been received.
“ackRegisterReply（3）”已收到肯定的注册回复。
'nakRegisterReply(4)' The client has received a
negative registration
reply (NAK)."
::= { nhrpClientRegistrationEntry 3 }
'nakRegisterReply(4)' The client has received a
negative registration
reply (NAK)."
::= { nhrpClientRegistrationEntry 3 }
nhrpClientRegRowStatus OBJECT-TYPE
NHRPCLI状态对象类型
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpClientRegistrationEntry 4 }
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpClientRegistrationEntry 4 }
-- -- The NHRP Client->Server Table --
----NHRP客户机->服务器表--
nhrpClientNhsTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpClientNhsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of NHSes that are available for use by this NHC
(client). By default, the agent will add an entry to this
table that corresponds to the client's default router."
::= { nhrpClientObjects 3 }
nhrpClientNhsTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpClientNhsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of NHSes that are available for use by this NHC
(client). By default, the agent will add an entry to this
table that corresponds to the client's default router."
::= { nhrpClientObjects 3 }
nhrpClientNhsEntry OBJECT-TYPE
SYNTAX NhrpClientNhsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An NHS that may be used by an NHC."
INDEX { nhrpClientIndex, nhrpClientNhsIndex }
::= { nhrpClientNhsTable 1 }
nhrpClientNhsEntry OBJECT-TYPE
SYNTAX NhrpClientNhsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An NHS that may be used by an NHC."
INDEX { nhrpClientIndex, nhrpClientNhsIndex }
::= { nhrpClientNhsTable 1 }
NhrpClientNhsEntry ::= SEQUENCE {
nhrpClientNhsIndex Unsigned32,
nhrpClientNhsInternetworkAddrType AddressFamilyNumbers,
nhrpClientNhsInternetworkAddr NhrpGenAddr,
nhrpClientNhsNbmaAddrType AddressFamilyNumbers,
nhrpClientNhsNbmaAddr NhrpGenAddr,
nhrpClientNhsNbmaSubaddr NhrpGenAddr,
nhrpClientNhsInUse TruthValue,
nhrpClientNhsRowStatus RowStatus
}
NhrpClientNhsEntry ::= SEQUENCE {
nhrpClientNhsIndex Unsigned32,
nhrpClientNhsInternetworkAddrType AddressFamilyNumbers,
nhrpClientNhsInternetworkAddr NhrpGenAddr,
nhrpClientNhsNbmaAddrType AddressFamilyNumbers,
nhrpClientNhsNbmaAddr NhrpGenAddr,
nhrpClientNhsNbmaSubaddr NhrpGenAddr,
nhrpClientNhsInUse TruthValue,
nhrpClientNhsRowStatus RowStatus
}
nhrpClientNhsIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for an NHS available to an NHC."
::= { nhrpClientNhsEntry 1 }
nhrpClientNhsIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for an NHS available to an NHC."
::= { nhrpClientNhsEntry 1 }
nhrpClientNhsInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of the
NHRP server represented in this entry. This object
indicates how the value of
nhrpClientNhsInternetworkAddr is to be interpreted."
::= { nhrpClientNhsEntry 2 }
nhrpClientNhsInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of the
NHRP server represented in this entry. This object
indicates how the value of
nhrpClientNhsInternetworkAddr is to be interpreted."
::= { nhrpClientNhsEntry 2 }
nhrpClientNhsInternetworkAddr OBJECT-TYPE SYNTAX NhrpGenAddr MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the destination internetwork layer address of the NHRP server represented by this
nhrpClientNhsInternetworkAddr对象类型语法NhrpGenAddr MAX-ACCESS read create STATUS current DESCRIPTION“此
entry. If this value is not known, this will be
a zero-length OCTET STRING."
::= { nhrpClientNhsEntry 3 }
entry. If this value is not known, this will be
a zero-length OCTET STRING."
::= { nhrpClientNhsEntry 3 }
nhrpClientNhsNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the NBMA subnetwork address of the NHRP
Server represented by this entry. This object indicates
how the values of nhrpClientNhsNbmaAddr and
nhrpClientNhsNbmaSubaddr are to be interpreted."
::= { nhrpClientNhsEntry 4 }
nhrpClientNhsNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the NBMA subnetwork address of the NHRP
Server represented by this entry. This object indicates
how the values of nhrpClientNhsNbmaAddr and
nhrpClientNhsNbmaSubaddr are to be interpreted."
::= { nhrpClientNhsEntry 4 }
nhrpClientNhsNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA subnetwork address of the NHS. The type of
the address is indicated by the corresponding value of
nhrpClientNhsNbmaAddrType."
::= { nhrpClientNhsEntry 5 }
nhrpClientNhsNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA subnetwork address of the NHS. The type of
the address is indicated by the corresponding value of
nhrpClientNhsNbmaAddrType."
::= { nhrpClientNhsEntry 5 }
nhrpClientNhsNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA subaddress of the NHS. For NMBA address
families that do not have the concept of subaddress,
this will be a zero-length OCTET STRING."
::= { nhrpClientNhsEntry 6 }
nhrpClientNhsNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA subaddress of the NHS. For NMBA address
families that do not have the concept of subaddress,
this will be a zero-length OCTET STRING."
::= { nhrpClientNhsEntry 6 }
nhrpClientNhsInUse OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether this NHS is in use by the NHC."
::= { nhrpClientNhsEntry 7 }
nhrpClientNhsInUse OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether this NHS is in use by the NHC."
::= { nhrpClientNhsEntry 7 }
nhrpClientNhsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current
nhrpClientNhsRowStatus对象类型语法RowStatus MAX-ACCESS read create STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpClientNhsEntry 8 }
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpClientNhsEntry 8 }
-- -- The NHRP Client StatisticsTable --
----NHRP客户统计表--
nhrpClientStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpClientStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains statistics collected by NHRP
clients."
::= { nhrpClientObjects 4 }
nhrpClientStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpClientStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains statistics collected by NHRP
clients."
::= { nhrpClientObjects 4 }
nhrpClientStatEntry OBJECT-TYPE
SYNTAX NhrpClientStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics collected by a NHRP client."
INDEX { nhrpClientIndex }
::= { nhrpClientStatTable 1 }
nhrpClientStatEntry OBJECT-TYPE
SYNTAX NhrpClientStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics collected by a NHRP client."
INDEX { nhrpClientIndex }
::= { nhrpClientStatTable 1 }
NhrpClientStatEntry ::= SEQUENCE {
nhrpClientStatTxResolveReq Counter32,
nhrpClientStatRxResolveReplyAck Counter32,
nhrpClientStatRxResolveReplyNakProhibited Counter32,
nhrpClientStatRxResolveReplyNakInsufResources Counter32,
nhrpClientStatRxResolveReplyNakNoBinding Counter32,
nhrpClientStatRxResolveReplyNakNotUnique Counter32,
nhrpClientStatTxRegisterReq Counter32,
nhrpClientStatRxRegisterAck Counter32,
nhrpClientStatRxRegisterNakProhibited Counter32,
nhrpClientStatRxRegisterNakInsufResources Counter32,
nhrpClientStatRxRegisterNakAlreadyReg Counter32,
NhrpClientStatEntry ::= SEQUENCE {
nhrpClientStatTxResolveReq Counter32,
nhrpClientStatRxResolveReplyAck Counter32,
nhrpClientStatRxResolveReplyNakProhibited Counter32,
nhrpClientStatRxResolveReplyNakInsufResources Counter32,
nhrpClientStatRxResolveReplyNakNoBinding Counter32,
nhrpClientStatRxResolveReplyNakNotUnique Counter32,
nhrpClientStatTxRegisterReq Counter32,
nhrpClientStatRxRegisterAck Counter32,
nhrpClientStatRxRegisterNakProhibited Counter32,
nhrpClientStatRxRegisterNakInsufResources Counter32,
nhrpClientStatRxRegisterNakAlreadyReg Counter32,
nhrpClientStatRxPurgeReq Counter32, nhrpClientStatTxPurgeReq Counter32, nhrpClientStatRxPurgeReply Counter32, nhrpClientStatTxPurgeReply Counter32,
NHRPClientStattXburgerEq计数器32、NHRPClientStattXburgerEq计数器32、NHRPClientStattXburgerEply计数器32、NHRPClientStattXburgerEply计数器32、，
nhrpClientStatTxErrorIndication Counter32, nhrpClientStatRxErrUnrecognizedExtension Counter32, nhrpClientStatRxErrLoopDetected Counter32,
NHRPClientStatXerror指示计数器32，NHRPClientStatRxerRunRecognitizedExtension计数器32，NHRPClientStatRxerLoopDetected计数器32，
nhrpClientStatRxErrProtoAddrUnreachable Counter32, nhrpClientStatRxErrProtoError Counter32, nhrpClientStatRxErrSduSizeExceeded Counter32, nhrpClientStatRxErrInvalidExtension Counter32, nhrpClientStatRxErrAuthenticationFailure Counter32, nhrpClientStatRxErrHopCountExceeded Counter32, nhrpClientStatDiscontinuityTime TimeStamp }
NHRPClientStatrXerProtoAddRunreachable计数器32，NHRPClientStatrXerProtoError计数器32，NHRPClientStatrXersDusizeExceed计数器32，nhrpClientStatRxErrInvalidExtension计数器32，NHRPClientStatrXerAuthenticationFailure计数器32，NHRPClientStatrXerHopCounterExceed计数器32，NHRPClientStatsContinuitTime时间戳}
nhrpClientStatTxResolveReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Resolution Requests transmitted by this client.
nhrpClientStatTxResolveReq对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端传输的NHRP解析请求数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 1 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 1 }
nhrpClientStatRxResolveReplyAck OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of positively acknowledged NHRP Resolution Replies received by this client.
nhrpClientStatRxResolveReplyAck对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端接收到的已确认的NHRP解析答复数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 2 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 2 }
nhrpClientStatRxResolveReplyNakProhibited OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NAKed NHRP Resolution Replies received by this client that contained the code indicating 'Administratively Prohibited'.
NHRPClientStatrxResolveReplyNakProbited对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端接收到的包含指示“管理禁止”代码的裸NHRP解析答复数。”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 3 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 3 }
nhrpClientStatRxResolveReplyNakInsufResources OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NAKed NHRP Resolution Replies received by this client that contained the code indicating 'Insufficient Resources'.
NHRPClientStatrxResolveReplyNakinSuresources对象类型语法计数器32 MAX-ACCESS只读状态当前说明“此客户端接收到的包含指示“资源不足”代码的裸NHRP解析答复数。”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 4 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 4 }
nhrpClientStatRxResolveReplyNakNoBinding OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NAKed NHRP Resolution Replies received by this client that contained the code indicating 'No Internetworking Layer Address to NBMA Address Binding Exists'.
nhrpClientStatRxResolveReplyNakNoBinding对象类型语法计数器32 MAX-ACCESS只读状态当前说明“此客户端接收到的裸NHRP解析答复数，其中包含指示“不存在到NBMA地址绑定的互联层地址”的代码。
Discontinuities in the value of this counter can occur at re-initialization of the management system, at NHRP Client re-initialization and at other times as indicated by the value of nhrpClientStatDiscontinuityTime."
在管理系统重新初始化、NHRP客户端重新初始化以及NHRPClientStatDiscontinuitTime值指示的其他时间，此计数器的值可能会出现不连续。”
::= { nhrpClientStatEntry 5 }
::= { nhrpClientStatEntry 5 }
nhrpClientStatRxResolveReplyNakNotUnique OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current
nhrpClientStatRxResolveReplyNakNotUnique对象类型语法计数器32 MAX-ACCESS只读状态当前
DESCRIPTION "The number of NAKed NHRP Resolution Replies received by this client that contained the code indicating 'Binding Exists But Is Not Unique'.
DESCRIPTION“此客户端接收的裸NHRP解析答复数，其中包含指示“绑定存在但不唯一”的代码。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 6 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 6 }
nhrpClientStatTxRegisterReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Registration Requests transmitted by this client.
nhrpClientStatTxRegisterReq对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端传输的NHRP注册请求数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 7 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 7 }
nhrpClientStatRxRegisterAck OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of positively acknowledged NHRP Registration Replies received by this client.
nhrpClientStatRxRegisterAck对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端接收到的已确认的NHRP注册回复数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 8 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 8 }
nhrpClientStatRxRegisterNakProhibited OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current
NHRPClientStatrxRegisternkProhibited对象类型语法计数器32 MAX-ACCESS只读状态当前
DESCRIPTION "The number of NAKed NHRP Registration Replies received by this client that contained the code indicating 'Administratively Prohibited'.
DESCRIPTION“此客户端收到的裸NHRP注册回复的数量，其中包含指示“管理禁止”的代码。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 9 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 9 }
nhrpClientStatRxRegisterNakInsufResources OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NAKed NHRP Registration Replies received by this client that contained the code indicating 'Insufficient Resources'.
nhrpClientStatRxRegisterNakInsufResources对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端接收到的包含指示“资源不足”代码的裸NHRP注册答复数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 10 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 10 }
nhrpClientStatRxRegisterNakAlreadyReg OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NAKed NHRP Registration Replies received by this client that contained the code indicating 'Unique Internetworking Layer Address Already Registered'.
NHRPClientStatrxRegisterNalReadyReg对象类型语法计数器32 MAX-ACCESS只读状态当前说明“此客户端接收到的裸NHRP注册回复数，其中包含指示“已注册唯一网络间层地址”的代码。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 11 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 11 }
nhrpClientStatRxPurgeReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current
NHRPClientStatrXburgerEq对象类型语法计数器32 MAX-ACCESS只读状态当前
DESCRIPTION "The number of NHRP Purge Requests received by this client.
DESCRIPTION“此客户端接收的NHRP清除请求数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 12 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 12 }
nhrpClientStatTxPurgeReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Purge Requests transmitted by this client.
NHRPClientStattXburgereq对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端传输的NHRP清除请求数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 13 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 13 }
nhrpClientStatRxPurgeReply OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Purge Replies received by this client.
nhrpClientStatRxPurgeReply对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端接收的NHRP清除回复数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 14 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 14 }
nhrpClientStatTxPurgeReply OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Purge Replies transmitted by this client.
nhrpClientStatTxPurgeReply对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端传输的NHRP清除回复数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 15 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
::= { nhrpClientStatEntry 15 }
nhrpClientStatTxErrorIndication OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets transmitted by this client.
NHRPClientStattXerorIndication对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端传输的NHRP错误指示数据包数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 16 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 16 }
nhrpClientStatRxErrUnrecognizedExtension OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this client with the error code 'Unrecognized Extension'.
NHRPClientStatrXerRunRecognitizedExtension对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端接收到的错误代码为“Unrecognized Extension”的NHRP错误指示数据包数。”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 17 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 17 }
nhrpClientStatRxErrLoopDetected OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current
NHRPClientStatrXerlLoopDetected对象类型语法计数器32 MAX-ACCESS只读状态当前
DESCRIPTION "The number of NHRP Error Indication packets received by this client with the error code 'NHRP Loop Detected'.
DESCRIPTION“此客户端接收的错误代码为“检测到NHRP循环”的NHRP错误指示数据包的数量。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 18 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 18 }
nhrpClientStatRxErrProtoAddrUnreachable OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this client with the error code 'Protocol Address Unreachable'.
NHRPClientStatrXerProtoAddRunReachable对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端接收到的错误代码为“协议地址不可访问”的NHRP错误指示数据包数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 19 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 19 }
nhrpClientStatRxErrProtoError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this client with the error code 'Protocol Error'.
NHRPCLIENTSTATRXERPROTOERROR对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端接收的错误代码为“协议错误”的NHRP错误指示数据包的数量。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 20 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 20 }
nhrpClientStatRxErrSduSizeExceeded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this client with the error code 'NHRP SDU Size
NHRPCLIENTSTATRXERSRSDUIZEEDED对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端接收的错误代码为“NHRP SDU Size”的NHRP错误指示数据包的数量
Exceeded'.
超过”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 21 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 21 }
nhrpClientStatRxErrInvalidExtension OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this client with the error code 'Invalid Extension'.
nhrpClientStatRxErrInvalidExtension对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端接收到的错误代码为“无效扩展名”的NHRP错误指示数据包数。”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 22 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 22 }
nhrpClientStatRxErrAuthenticationFailure OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this client with the error code 'Authentication Failure'.
NHRPClientStatrXerouthenticationFailure对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此客户端接收到的错误代码为“身份验证失败”的NHRP错误指示数据包数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 23 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 23 }
nhrpClientStatRxErrHopCountExceeded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current
NHRPCLIENTSTATRXERHOPCOUNTEXCEED对象类型语法计数器32 MAX-ACCESS只读状态当前
DESCRIPTION "The number of NHRP Error Indication packets received by this client with the error code 'Hop Count Exceeded'.
DESCRIPTION“此客户端接收到的错误代码为“超出跃点计数”的NHRP错误指示数据包的数量。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 24 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Client re-initialization and at
other times as indicated by the value of
nhrpClientStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpClientStatEntry 24 }
nhrpClientStatDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at
which any one or more of this Client's counters
suffered a discontinuity. If no such discontinuities
have occurred since the last re-initialization of the
local management subsystem or the NHRP Client
re-initialization associated with this entry, then
this object contains a zero value."
REFERENCE
"RFC 2233 [18]."
::= { nhrpClientStatEntry 25 }
nhrpClientStatDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at
which any one or more of this Client's counters
suffered a discontinuity. If no such discontinuities
have occurred since the last re-initialization of the
local management subsystem or the NHRP Client
re-initialization associated with this entry, then
this object contains a zero value."
REFERENCE
"RFC 2233 [18]."
::= { nhrpClientStatEntry 25 }
--****************************************************************
-- NHRP Server Objects
--****************************************************************
--****************************************************************
-- NHRP Server Objects
--****************************************************************
nhrpServerObjects OBJECT IDENTIFIER ::= { nhrpObjects 3 }
nhrpServerObjects OBJECT IDENTIFIER ::= { nhrpObjects 3 }
-- -- The NHRP Next Hop Server Table --
----NHRP下一跳服务器表--
nhrpServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information for a set of NHSes
associated with this agent."
::= { nhrpServerObjects 1 }
nhrpServerTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information for a set of NHSes
associated with this agent."
::= { nhrpServerObjects 1 }
nhrpServerEntry OBJECT-TYPE
SYNTAX NhrpServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single NHS."
INDEX { nhrpServerIndex }
::= { nhrpServerTable 1 }
nhrpServerEntry OBJECT-TYPE
SYNTAX NhrpServerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single NHS."
INDEX { nhrpServerIndex }
::= { nhrpServerTable 1 }
NhrpServerEntry ::= SEQUENCE {
nhrpServerIndex Unsigned32,
nhrpServerInternetworkAddrType AddressFamilyNumbers,
nhrpServerInternetworkAddr NhrpGenAddr,
nhrpServerNbmaAddrType AddressFamilyNumbers,
nhrpServerNbmaAddr NhrpGenAddr,
nhrpServerNbmaSubaddr NhrpGenAddr,
nhrpServerStorageType StorageType,
nhrpServerRowStatus RowStatus
}
NhrpServerEntry ::= SEQUENCE {
nhrpServerIndex Unsigned32,
nhrpServerInternetworkAddrType AddressFamilyNumbers,
nhrpServerInternetworkAddr NhrpGenAddr,
nhrpServerNbmaAddrType AddressFamilyNumbers,
nhrpServerNbmaAddr NhrpGenAddr,
nhrpServerNbmaSubaddr NhrpGenAddr,
nhrpServerStorageType StorageType,
nhrpServerRowStatus RowStatus
}
nhrpServerIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for the server that is unique within the
scope of this agent."
::= { nhrpServerEntry 1 }
nhrpServerIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for the server that is unique within the
scope of this agent."
::= { nhrpServerEntry 1 }
nhrpServerInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of this
server. This object is used to interpret the value of
nhrpServerInternetworkAddr."
::= { nhrpServerEntry 2 }
nhrpServerInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of this
server. This object is used to interpret the value of
nhrpServerInternetworkAddr."
::= { nhrpServerEntry 2 }
nhrpServerInternetworkAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork layer address of this
server."
::= { nhrpServerEntry 3 }
nhrpServerInternetworkAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork layer address of this
server."
::= { nhrpServerEntry 3 }
nhrpServerNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the NBMA subnetwork address of this server.
This object is used to interpret the value of
nhrpServerNbmaAddr."
::= { nhrpServerEntry 4 }
nhrpServerNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the NBMA subnetwork address of this server.
This object is used to interpret the value of
nhrpServerNbmaAddr."
::= { nhrpServerEntry 4 }
nhrpServerNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the NBMA subnetwork address of this
server."
::= { nhrpServerEntry 5 }
nhrpServerNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the NBMA subnetwork address of this
server."
::= { nhrpServerEntry 5 }
nhrpServerNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the NBMA subaddress of this server.
For NBMA address families without a subaddress
concept, this will be a zero-length OCTET STRING."
::= { nhrpServerEntry 6 }
nhrpServerNbmaSubaddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the NBMA subaddress of this server.
For NBMA address families without a subaddress
concept, this will be a zero-length OCTET STRING."
::= { nhrpServerEntry 6 }
nhrpServerStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object defines whether this row is kept in
volatile storage and lost upon a Server crash or
reboot situation, or if this row is backed up by
nonvolatile or permanent storage."
DEFVAL { nonVolatile }
::= { nhrpServerEntry 7 }
nhrpServerStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object defines whether this row is kept in
volatile storage and lost upon a Server crash or
reboot situation, or if this row is backed up by
nonvolatile or permanent storage."
DEFVAL { nonVolatile }
::= { nhrpServerEntry 7 }
nhrpServerRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpServerEntry 8 }
nhrpServerRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpServerEntry 8 }
-- -- The Server Cache Table -- nhrpServerCacheTable OBJECT-TYPE SYNTAX SEQUENCE OF NhrpServerCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table extends the nhrpCacheTable for NHSes. If the nhrpCacheTable has a row added due to an NHS or based on information regarding an NHS then a row is also added in this table.
----服务器缓存表--nhrpServerCacheTable对象类型语法序列NhrpServerCacheEntry MAX-ACCESS不可访问状态当前描述“此表扩展NHSE的nhrpCacheTable。如果nhrpCacheTable由于NHS或基于有关NHS的信息而添加了一行，则此表中也会添加一行。
The rows in this table will be created when rows in
the nhrpCacheTable are created. However, there may
be rows created in the nhrpCacheTable which do not
have corresponding rows in this table. For example,
if the nhrpCacheTable has a row added due to a Next
Hop Client which is co-resident on the same device
as the NHS, a row will not be added to this table."
::= { nhrpServerObjects 2 }
The rows in this table will be created when rows in
the nhrpCacheTable are created. However, there may
be rows created in the nhrpCacheTable which do not
have corresponding rows in this table. For example,
if the nhrpCacheTable has a row added due to a Next
Hop Client which is co-resident on the same device
as the NHS, a row will not be added to this table."
::= { nhrpServerObjects 2 }
nhrpServerCacheEntry OBJECT-TYPE SYNTAX NhrpServerCacheEntry MAX-ACCESS not-accessible STATUS current
nhrpServerCacheEntry对象类型语法nhrpServerCacheEntry MAX-ACCESS不可访问状态当前
DESCRIPTION
"Additional information kept by a NHS for a relevant
Next Hop Resolution Cache entry."
INDEX {
nhrpCacheInternetworkAddrType,
nhrpCacheInternetworkAddr,
ifIndex,
nhrpCacheIndex
}
::= { nhrpServerCacheTable 1 }
DESCRIPTION
"Additional information kept by a NHS for a relevant
Next Hop Resolution Cache entry."
INDEX {
nhrpCacheInternetworkAddrType,
nhrpCacheInternetworkAddr,
ifIndex,
nhrpCacheIndex
}
::= { nhrpServerCacheTable 1 }
NhrpServerCacheEntry ::= SEQUENCE {
nhrpServerCacheAuthoritative TruthValue,
nhrpServerCacheUniqueness TruthValue
}
NhrpServerCacheEntry ::= SEQUENCE {
nhrpServerCacheAuthoritative TruthValue,
nhrpServerCacheUniqueness TruthValue
}
nhrpServerCacheAuthoritative OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether this cache entry is
authoritative, which means the entry was added because
of a direct registration request with this server or
by Server Cache Synchronization Protocol (SCSP) from
an authoritative source."
::= { nhrpServerCacheEntry 1 }
nhrpServerCacheAuthoritative OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether this cache entry is
authoritative, which means the entry was added because
of a direct registration request with this server or
by Server Cache Synchronization Protocol (SCSP) from
an authoritative source."
::= { nhrpServerCacheEntry 1 }
nhrpServerCacheUniqueness OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Uniqueness indicator for this cache
entry used in duplicate address detection. This value
cannot be changed after the entry is active."
::= { nhrpServerCacheEntry 2 }
nhrpServerCacheUniqueness OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Uniqueness indicator for this cache
entry used in duplicate address detection. This value
cannot be changed after the entry is active."
::= { nhrpServerCacheEntry 2 }
-- -- The NHRP Server->Client Table --
----NHRP服务器->客户机表--
nhrpServerNhcTable OBJECT-TYPE SYNTAX SEQUENCE OF NhrpServerNhcEntry MAX-ACCESS not-accessible STATUS current
nhrpServerNhcTable NhrpServerNhcEntry MAX-ACCESS的对象类型语法序列不可访问状态当前
DESCRIPTION
"A table of NHCs that are available for use by this NHS
(Server)."
REFERENCE
"Section 4 Configuration (Next Hop Servers),
RFC 2332 [17]."
::= { nhrpServerObjects 3 }
DESCRIPTION
"A table of NHCs that are available for use by this NHS
(Server)."
REFERENCE
"Section 4 Configuration (Next Hop Servers),
RFC 2332 [17]."
::= { nhrpServerObjects 3 }
nhrpServerNhcEntry OBJECT-TYPE
SYNTAX NhrpServerNhcEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An NHC that may be used by an NHS."
INDEX { nhrpServerIndex, nhrpServerNhcIndex }
::= { nhrpServerNhcTable 1 }
nhrpServerNhcEntry OBJECT-TYPE
SYNTAX NhrpServerNhcEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An NHC that may be used by an NHS."
INDEX { nhrpServerIndex, nhrpServerNhcIndex }
::= { nhrpServerNhcTable 1 }
NhrpServerNhcEntry ::= SEQUENCE {
nhrpServerNhcIndex Unsigned32,
nhrpServerNhcPrefixLength Integer32,
nhrpServerNhcInternetworkAddrType AddressFamilyNumbers,
nhrpServerNhcInternetworkAddr NhrpGenAddr,
nhrpServerNhcNbmaAddrType AddressFamilyNumbers,
nhrpServerNhcNbmaAddr NhrpGenAddr,
nhrpServerNhcNbmaSubaddr NhrpGenAddr,
nhrpServerNhcInUse TruthValue,
nhrpServerNhcRowStatus RowStatus
}
NhrpServerNhcEntry ::= SEQUENCE {
nhrpServerNhcIndex Unsigned32,
nhrpServerNhcPrefixLength Integer32,
nhrpServerNhcInternetworkAddrType AddressFamilyNumbers,
nhrpServerNhcInternetworkAddr NhrpGenAddr,
nhrpServerNhcNbmaAddrType AddressFamilyNumbers,
nhrpServerNhcNbmaAddr NhrpGenAddr,
nhrpServerNhcNbmaSubaddr NhrpGenAddr,
nhrpServerNhcInUse TruthValue,
nhrpServerNhcRowStatus RowStatus
}
nhrpServerNhcIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for an NHC available to an NHS."
::= { nhrpServerNhcEntry 1 }
nhrpServerNhcIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for an NHC available to an NHS."
::= { nhrpServerNhcEntry 1 }
nhrpServerNhcPrefixLength OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of bits that define the internetwork
layer prefix associated with the
nhrpServerNhcInternetworkAddr."
::= { nhrpServerNhcEntry 2 }
nhrpServerNhcPrefixLength OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of bits that define the internetwork
layer prefix associated with the
nhrpServerNhcInternetworkAddr."
::= { nhrpServerNhcEntry 2 }
nhrpServerNhcInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of the
NHRP Client represented in this entry. This object
indicates how the value of nhrpServerNhcInternetworkAddr
is to be interpreted."
::= { nhrpServerNhcEntry 3 }
nhrpServerNhcInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of the
NHRP Client represented in this entry. This object
indicates how the value of nhrpServerNhcInternetworkAddr
is to be interpreted."
::= { nhrpServerNhcEntry 3 }
nhrpServerNhcInternetworkAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork layer address of
the NHRP Client represented by this entry. If this
value is not known, this will be a zero-length
OCTET STRING."
::= { nhrpServerNhcEntry 4 }
nhrpServerNhcInternetworkAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork layer address of
the NHRP Client represented by this entry. If this
value is not known, this will be a zero-length
OCTET STRING."
::= { nhrpServerNhcEntry 4 }
nhrpServerNhcNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the NBMA subnetwork address of the NHRP
Client represented by this entry. This object indicates
how the values of nhrpServerNhcNbmaAddr and
nhrpServerNhcNbmaSubaddr are to be interpreted."
::= { nhrpServerNhcEntry 5 }
nhrpServerNhcNbmaAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the NBMA subnetwork address of the NHRP
Client represented by this entry. This object indicates
how the values of nhrpServerNhcNbmaAddr and
nhrpServerNhcNbmaSubaddr are to be interpreted."
::= { nhrpServerNhcEntry 5 }
nhrpServerNhcNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA subnetwork address of the NHC. The type of the
address is indicated by the corresponding value of
nhrpServerNbmaAddrType."
::= { nhrpServerNhcEntry 6 }
nhrpServerNhcNbmaAddr OBJECT-TYPE
SYNTAX NhrpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The NBMA subnetwork address of the NHC. The type of the
address is indicated by the corresponding value of
nhrpServerNbmaAddrType."
::= { nhrpServerNhcEntry 6 }
nhrpServerNhcNbmaSubaddr OBJECT-TYPE SYNTAX NhrpGenAddr MAX-ACCESS read-create STATUS current
NHRPServerNHCNBMASUBADR对象类型语法NhrpGenAddr MAX-ACCESS read create STATUS current
DESCRIPTION
"The NBMA subaddress of the NHC. For NMBA address familes
that do not have the concept of subaddress, this will
be a zero-length OCTET STRING."
::= { nhrpServerNhcEntry 7 }
DESCRIPTION
"The NBMA subaddress of the NHC. For NMBA address familes
that do not have the concept of subaddress, this will
be a zero-length OCTET STRING."
::= { nhrpServerNhcEntry 7 }
nhrpServerNhcInUse OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether this NHC is in use by the NHS."
::= { nhrpServerNhcEntry 8 }
nhrpServerNhcInUse OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether this NHC is in use by the NHS."
::= { nhrpServerNhcEntry 8 }
nhrpServerNhcRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpServerNhcEntry 9 }
nhrpServerNhcRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be
created and deleted using the RowStatus convention."
::= { nhrpServerNhcEntry 9 }
-- -- The Next Hop Server Statistics Table --
----下一跳服务器统计表--
nhrpServerStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpServerStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics collected by Next Hop Servers."
::= { nhrpServerObjects 4 }
nhrpServerStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF NhrpServerStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics collected by Next Hop Servers."
::= { nhrpServerObjects 4 }
nhrpServerStatEntry OBJECT-TYPE
SYNTAX NhrpServerStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics for a particular NHS. The statistics are
broken into received (Rx), transmitted (Tx)
and forwarded (Fw). Forwarded (Fw) would be done
by a transit NHS."
INDEX { nhrpServerIndex }
::= { nhrpServerStatTable 1 }
nhrpServerStatEntry OBJECT-TYPE
SYNTAX NhrpServerStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Statistics for a particular NHS. The statistics are
broken into received (Rx), transmitted (Tx)
and forwarded (Fw). Forwarded (Fw) would be done
by a transit NHS."
INDEX { nhrpServerIndex }
::= { nhrpServerStatTable 1 }
NhrpServerStatEntry ::= SEQUENCE {
nhrpServerStatRxResolveReq Counter32,
nhrpServerStatTxResolveReplyAck Counter32,
nhrpServerStatTxResolveReplyNakProhibited Counter32,
nhrpServerStatTxResolveReplyNakInsufResources Counter32,
nhrpServerStatTxResolveReplyNakNoBinding Counter32,
nhrpServerStatTxResolveReplyNakNotUnique Counter32,
NhrpServerStatEntry ::= SEQUENCE {
nhrpServerStatRxResolveReq Counter32,
nhrpServerStatTxResolveReplyAck Counter32,
nhrpServerStatTxResolveReplyNakProhibited Counter32,
nhrpServerStatTxResolveReplyNakInsufResources Counter32,
nhrpServerStatTxResolveReplyNakNoBinding Counter32,
nhrpServerStatTxResolveReplyNakNotUnique Counter32,
nhrpServerStatRxRegisterReq Counter32, nhrpServerStatTxRegisterAck Counter32, nhrpServerStatTxRegisterNakProhibited Counter32, nhrpServerStatTxRegisterNakInsufResources Counter32, nhrpServerStatTxRegisterNakAlreadyReg Counter32,
nhrpServerStatRxRegisterReq计数器32、NHRPServerStattXRegisterBack计数器32、nhrpServerStatTxRegisterNakProhibited计数器32、NHRPServerStattXRegisterNakSufResources计数器32、NHRPServerStattXRegisterNalkReadyReg计数器32、，
nhrpServerStatRxPurgeReq Counter32, nhrpServerStatTxPurgeReq Counter32, nhrpServerStatRxPurgeReply Counter32, nhrpServerStatTxPurgeReply Counter32,
NHRPServerStatRxPergerEq计数器32、NHRPServerStatTxPergerEq计数器32、NHRPServerStatRxPergerEply计数器32、NHRPServerStatTxPergerEply计数器32、，
-- Error Indications nhrpServerStatRxErrUnrecognizedExtension Counter32, nhrpServerStatRxErrLoopDetected Counter32, nhrpServerStatRxErrProtoAddrUnreachable Counter32, nhrpServerStatRxErrProtoError Counter32, nhrpServerStatRxErrSduSizeExceeded Counter32, nhrpServerStatRxErrInvalidExtension Counter32, nhrpServerStatRxErrInvalidResReplyReceived Counter32, nhrpServerStatRxErrAuthenticationFailure Counter32, nhrpServerStatRxErrHopCountExceeded Counter32,
--错误指示NHRPServerStatrXerRunRecognitizedExtension计数器32、NHRPServerStatrXerLoopDetected计数器32、NHRPServerStatrXerProtoAddRunReach计数器32、NHRPServerStatrXerProtoError计数器32、NHRPServerStatrXersDusizeExceed计数器32、nhrpServerStatRxErrInvalidExtension计数器32、，NHRPServerStatrXerRinValidReceived计数器32，NHRPServerStatrXerRouthenticationFailure计数器32，NHRPServerStatrXerHopCounter32，
nhrpServerStatTxErrUnrecognizedExtension Counter32, nhrpServerStatTxErrLoopDetected Counter32, nhrpServerStatTxErrProtoAddrUnreachable Counter32, nhrpServerStatTxErrProtoError Counter32, nhrpServerStatTxErrSduSizeExceeded Counter32, nhrpServerStatTxErrInvalidExtension Counter32, nhrpServerStatTxErrAuthenticationFailure Counter32, nhrpServerStatTxErrHopCountExceeded Counter32,
NHRPServerStattXerRunRecognitizedExtension计数器32、NHRPServerStattXerLoopDetected计数器32、NHRPServerStattXerProtoAddRunReachable计数器32、NHRPServerStattXerProtoError计数器32、NHRPServerStattXersDusizeExceed计数器32、nhrpServerStatTxErrInvalidExtension计数器32、NHRPServerStattXerRouthenticationFailure计数器32、，NHRPServerStattXerhopCounter32，
-- Transit NHS statistics nhrpServerStatFwResolveReq Counter32, nhrpServerStatFwResolveReply Counter32, nhrpServerStatFwRegisterReq Counter32, nhrpServerStatFwRegisterReply Counter32, nhrpServerStatFwPurgeReq Counter32, nhrpServerStatFwPurgeReply Counter32, nhrpServerStatFwErrorIndication Counter32, nhrpServerStatDiscontinuityTime TimeStamp
--传输NHS统计数据nhrpServerStatFwResolveReq计数器32、nhrpServerStatFwResolveReply计数器32、NHRPServerStatfWresterReq计数器32、NHRPServerStatfWresterReply计数器32、NHRPServerStatfWpergerEq计数器32、NHRPServerStatfWpergerEply计数器32、nhrpServerStatFwErrorIndication计数器32、NHRPServerStatdDiscontinuitTime时间戳
}
}
nhrpServerStatRxResolveReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Resolution Requests received by this server.
nhrpServerStatRxResolveReq对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器接收的NHRP解析请求数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 1 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 1 }
nhrpServerStatTxResolveReplyAck OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of positively acknowledged NHRP Resolution Replies transmitted by this server.
nhrpServerStatTxResolveReplyAck对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器传输的已确认的NHRP解析答复数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 2 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 2 }
nhrpServerStatTxResolveReplyNakProhibited OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NAKed NHRP Resolution Replies transmitted by this server with the code 'Administratively Prohibited'.
NHRPServerStattxResolveReplyNakProbited对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器传输的代码为“管理禁止”的裸NHRP解析答复数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 3 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 3 }
nhrpServerStatTxResolveReplyNakInsufResources OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NAKed NHRP Resolution Replies transmitted by this server with the code 'Insufficient Resources'.
nhrpServerStatTxResolveReplyNakInsufResources对象类型语法计数器32 MAX-ACCESS只读状态当前说明“此服务器传输的代码为“资源不足”的裸NHRP解析答复数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 4 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 4 }
nhrpServerStatTxResolveReplyNakNoBinding OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NAKed NHRP Resolution Replies transmitted by this server with the code 'No Internetworking Layer Address to NBMA Address Binding Exists'.
nhrpServerStatTxResolveReplyNakNoBinding对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器传输的裸NHRP解析答复数，代码为“不存在网络互连层地址到NBMA地址绑定”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 5 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 5 }
nhrpServerStatTxResolveReplyNakNotUnique OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NAKed NHRP Resolution Replies transmitted by this server with the code 'Binding Exists But Is Not Unique'.
nhrpServerStatTxResolveReplyNakNotUnique对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器传输的裸NHRP解析答复数，代码为“绑定存在但不唯一”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 6 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 6 }
nhrpServerStatRxRegisterReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Registration Requests received by this server.
nhrpServerStatRxRegisterReq对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器接收的NHRP注册请求数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 7 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 7 }
nhrpServerStatTxRegisterAck OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of positively acknowledged NHRP Registration Replies transmitted by this server.
nhrpServerStatTxRegisterAck对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器传输的已确认NHRP注册回复数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 8 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 8 }
nhrpServerStatTxRegisterNakProhibited OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NAKed NHRP Registration Replies transmitted by this server with the code 'Administratively Prohibited'.
nhrpServerStatTxRegisterNakProhibited对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器发送的代码为“管理禁止”的裸NHRP注册回复数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 9 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 9 }
nhrpServerStatTxRegisterNakInsufResources OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NAKed NHRP Registration Replies transmitted by this server with the code 'Insufficient Resources'.
nhrpServerStatTxRegisterNakInsufResources对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器发送的代码为“资源不足”的裸NHRP注册回复数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 10 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 10 }
nhrpServerStatTxRegisterNakAlreadyReg OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NAKed NHRP Registration Replies transmitted by this server with the code 'Unique Internetworking Layer Address Already Registered'.
nhrpServerStatTxRegisterNakAlreadyReg对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器传输的裸NHRP注册回复数，代码为‘已注册的唯一网络互连层地址’。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 11 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 11 }
nhrpServerStatRxPurgeReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Purge Requests received by this server.
NHRPServerStatRxPergerEQ对象类型语法计数器32 MAX-ACCESS只读状态当前说明“此服务器接收的NHRP清除请求数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 12 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 12 }
nhrpServerStatTxPurgeReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Purge Requests transmitted by this server.
NHRPServerStattXburgerEq对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器传输的NHRP清除请求数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 13 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 13 }
nhrpServerStatRxPurgeReply OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Purge Replies received by this server.
nhrpServerStatRxPurgeReply对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器接收的NHRP清除回复数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 14 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 14 }
nhrpServerStatTxPurgeReply OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Purge Replies transmitted by this server.
nhrpServerStatTxPurgeReply对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器传输的NHRP清除回复数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 15 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 15 }
nhrpServerStatRxErrUnrecognizedExtension OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only
NHRPServerStatrXerRunRecognitizedExtension对象类型语法计数器32 MAX-ACCESS只读
STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this server with the error code
STATUS current DESCRIPTION“此服务器接收的带有错误代码的NHRP错误指示数据包的数量
'Unrecognized Extension'.
“无法识别的扩展名”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 16 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 16 }
nhrpServerStatRxErrLoopDetected OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this server with the error code 'NHRP Loop Detected'.
NHRPServerStatrXerlLoopDetected对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器接收到的错误代码为“检测到NHRP循环”的NHRP错误指示数据包数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 17 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 17 }
nhrpServerStatRxErrProtoAddrUnreachable OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this server with the error code 'Protocol Address Unreachable'.
NHRPServerStatrXerProtoAddRunReachable对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器接收到的错误代码为“协议地址不可访问”的NHRP错误指示数据包数。”。
Discontinuities in the value of this counter can occur at re-initialization of the management system, at NHRP Server re-initialization and at other times as indicated by the value of nhrpServerStatDiscontinuityTime."
在管理系统重新初始化、NHRP服务器重新初始化以及NHRPServerStatDiscontinuitTime值指示的其他时间，此计数器的值可能会出现不连续。”
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 18 }
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 18 }
nhrpServerStatRxErrProtoError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current
NHRPServerStatrXerProtoError对象类型语法计数器32 MAX-ACCESS只读状态当前
DESCRIPTION "The number of NHRP Error Indication packets received by this server with the error code 'Protocol Error'.
DESCRIPTION“此服务器接收的错误代码为“协议错误”的NHRP错误指示数据包的数量。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 19 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 19 }
nhrpServerStatRxErrSduSizeExceeded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this server with the error code 'NHRP SDU Size Exceeded'.
NHRPServerStatrXerSrsDusizeExceed对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器接收到的错误代码为“超出NHRP SDU大小”的NHRP错误指示数据包数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 20 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 20 }
nhrpServerStatRxErrInvalidExtension OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current
nhrpServerStatRxErrInvalidExtension对象类型语法计数器32 MAX-ACCESS只读状态当前
DESCRIPTION "The number of NHRP Error Indication packets received by this server with the error code 'Invalid Extension'.
DESCRIPTION“此服务器接收到的错误代码为“无效扩展名”的NHRP错误指示数据包数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 21 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 21 }
nhrpServerStatRxErrInvalidResReplyReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this server with the error code 'Invalid Resolution Reply Received'.
nhrpServerStatRxErrInvalidResReplyReceived对象类型语法计数器32 MAX-ACCESS只读状态当前说明“此服务器接收到的错误代码为“接收到无效解析答复”的NHRP错误指示数据包数。”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 22 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 22 }
nhrpServerStatRxErrAuthenticationFailure OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this server with the error code 'Authentication Failure'.
NHRPServerStatRxerAuthenticationFailure对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器接收到的错误代码为“身份验证失败”的NHRP错误指示数据包的数量。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 23 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 23 }
nhrpServerStatRxErrHopCountExceeded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets received by this server with the error code 'Hop Count Exceeded'.
NHRPServerStatrXerhopCountExcepended对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器接收到的错误代码为“超出跃点计数”的NHRP错误指示数据包数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 24 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 24 }
nhrpServerStatTxErrUnrecognizedExtension OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets transmitted by this server with the error code 'Unrecognized Extension'.
NHRPServerStattXerRunRecognitizedExtension对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器发送的错误代码为“Unrecognized Extension”的NHRP错误指示数据包的数量。”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 25 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 25 }
nhrpServerStatTxErrLoopDetected OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets transmitted by this server with the error code 'NHRP Loop Detected'.
NHRPServerStattXerlLoopDetected对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器发送的错误代码为“检测到NHRP循环”的NHRP错误指示数据包数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 26 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 26 }
nhrpServerStatTxErrProtoAddrUnreachable OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets transmitted by this server with the error code 'Protocol Address Unreachable'.
NHRPServerStattXerProtoAddRunReachable对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器发送的错误代码为“协议地址不可访问”的NHRP错误指示数据包的数量。”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 27 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 27 }
nhrpServerStatTxErrProtoError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets transmitted by this server with the error code 'Protocol Error'.
NHRPServerStattXerProtoError对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器发送的错误代码为“协议错误”的NHRP错误指示数据包的数量。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 28 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 28 }
nhrpServerStatTxErrSduSizeExceeded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets transmitted by this server with the error code 'NHRP SDU Size Exceeded'.
NHRPServerStattXerSrsDusizeExceeded对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器发送的错误代码为“超出NHRP SDU大小”的NHRP错误指示数据包数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 29 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 29 }
nhrpServerStatTxErrInvalidExtension OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets transmitted by this server with the error code
nhrpServerStatTxErrInvalidExtension对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器发送的带有错误代码的NHRP错误指示数据包的数量
'Invalid Extension'.
“无效扩展名”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 30 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 30 }
nhrpServerStatTxErrAuthenticationFailure OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets transmitted by this server with the error code 'Authentication Failure'.
NHRPServerStattXerouthenticationFailure对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器发送的错误代码为“身份验证失败”的NHRP错误指示数据包的数量。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 31 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 31 }
nhrpServerStatTxErrHopCountExceeded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets transmitted by this server with the error code 'Hop Count Exceeded'.
NHRPServerStattXerhopCountExcepended对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器发送的错误代码为“超出跃点计数”的NHRP错误指示数据包数”。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 32 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
REFERENCE
"Section 5.2.7 NHRP Error Indication, RFC 2332 [17]."
::= { nhrpServerStatEntry 32 }
nhrpServerStatFwResolveReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Resolution Requests forwarded by this server acting as a transit NHS.
nhrpServerStatFwResolveReq对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器作为传输NHS转发的NHRP解析请求数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 33 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 33 }
nhrpServerStatFwResolveReply OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current
nhrpServerStatFwResolveReply对象类型语法计数器32 MAX-ACCESS只读状态当前
DESCRIPTION "The number of NHRP Resolution Replies forwarded by this server acting as a transit NHS.
DESCRIPTION“此服务器作为中转NHS转发的NHRP解析回复数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 34 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 34 }
nhrpServerStatFwRegisterReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Registration Requests forwarded by this server acting as a transit NHS.
nhrpServerStatFwRegisterReq对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器作为传输NHS转发的NHRP注册请求数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 35 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 35 }
nhrpServerStatFwRegisterReply OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Registration Replies forwarded
by this server acting as a transit NHS.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 36 }
nhrpServerStatFwRegisterReply OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of NHRP Registration Replies forwarded
by this server acting as a transit NHS.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 36 }
nhrpServerStatFwPurgeReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Purge Requests forwarded by this server acting as a transit NHS.
nhrpServerStatFwPurgeReq对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器作为传输NHS转发的NHRP清除请求数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 37 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 37 }
nhrpServerStatFwPurgeReply OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Purge Replies forwarded by this server acting as a transit NHS.
nhrpServerStatFwPurgeReply对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器作为传输NHS转发的NHRP清除回复数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 38 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 38 }
nhrpServerStatFwErrorIndication OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of NHRP Error Indication packets forwarded by this server acting as a transit NHS.
nhrpServerStatFwErrorIndication对象类型语法计数器32 MAX-ACCESS只读状态当前描述“此服务器作为传输NHS转发的NHRP错误指示数据包数。
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 39 }
Discontinuities in the value of this counter can occur
at re-initialization of the management system, at
NHRP Server re-initialization and at
other times as indicated by the value of
nhrpServerStatDiscontinuityTime."
::= { nhrpServerStatEntry 39 }
nhrpServerStatDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this Server's counters suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the
NHRPServerStatDiscontinuitTime对象类型语法时间戳MAX-ACCESS只读状态当前描述“此服务器的任何一个或多个计数器最近发生中断时的sysUpTime值。如果自上次重新初始化
local management subsystem or the NHRP Server
re-initialization associated with this entry, then
this object contains a zero value."
REFERENCE
"RFC 2233 [18]."
::= { nhrpServerStatEntry 40 }
local management subsystem or the NHRP Server
re-initialization associated with this entry, then
this object contains a zero value."
REFERENCE
"RFC 2233 [18]."
::= { nhrpServerStatEntry 40 }
--****************************************************************
-- Module Compliance Statement
--****************************************************************
--****************************************************************
-- Module Compliance Statement
--****************************************************************
nhrpConformance OBJECT IDENTIFIER ::= { nhrpMIB 2 }
nhrpConformance OBJECT IDENTIFIER ::= { nhrpMIB 2 }
nhrpCompliances
OBJECT IDENTIFIER ::= { nhrpConformance 1 }
nhrpCompliances
OBJECT IDENTIFIER ::= { nhrpConformance 1 }
nhrpGroups
OBJECT IDENTIFIER ::= { nhrpConformance 2 }
nhrpGroups
OBJECT IDENTIFIER ::= { nhrpConformance 2 }
nhrpModuleCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the NHRP MIB." MODULE -- this module MANDATORY-GROUPS { nhrpGeneralGroup }
nhrpModuleCompliance MODULE-COMPLIANCE状态当前描述“NHRP MIB的符合性声明”。模块--此模块为必填项-GROUPS{nhrpGeneralGroup}
GROUP nhrpClientGroup DESCRIPTION "This group must be supported only by stations that are NHRP clients."
GROUP nhrpClientGroup DESCRIPTION“此组必须仅由作为NHRP客户端的站点支持。”
GROUP nhrpServerGroup
DESCRIPTION
"This group must be supported only by stations that
are NHRP servers."
::= { nhrpCompliances 1 }
GROUP nhrpServerGroup
DESCRIPTION
"This group must be supported only by stations that
are NHRP servers."
::= { nhrpCompliances 1 }
nhrpGeneralGroup OBJECT-GROUP OBJECTS {
nhrpGeneralGroup对象组对象{
nhrpNextIndex, nhrpCachePrefixLength, nhrpCacheNextHopInternetworkAddr, nhrpCacheNbmaAddrType, nhrpCacheNbmaAddr, nhrpCacheNbmaSubaddr, nhrpCacheType, nhrpCacheState,
nhrpNextIndex、nhrpCachePrefixLength、nhrpCacheNextHopInternetworkAddr、NHRPCacheNbMaAddType、nhrpCacheNbmaAddr、nhrpCacheNbmaSubaddr、nhrpCacheType、nhrpCacheState、，
nhrpCacheHoldingTimeValid,
nhrpCacheHoldingTime,
nhrpCacheNegotiatedMtu,
nhrpCachePreference,
nhrpCacheStorageType,
nhrpCacheRowStatus,
nhrpPurgeCacheIdentifier,
nhrpPurgePrefixLength,
nhrpPurgeRequestID,
nhrpPurgeReplyExpected,
nhrpPurgeRowStatus
}
STATUS current
DESCRIPTION
"Objects that apply to both NHRP clients and NHRP
servers."
::= { nhrpGroups 1 }
nhrpCacheHoldingTimeValid,
nhrpCacheHoldingTime,
nhrpCacheNegotiatedMtu,
nhrpCachePreference,
nhrpCacheStorageType,
nhrpCacheRowStatus,
nhrpPurgeCacheIdentifier,
nhrpPurgePrefixLength,
nhrpPurgeRequestID,
nhrpPurgeReplyExpected,
nhrpPurgeRowStatus
}
STATUS current
DESCRIPTION
"Objects that apply to both NHRP clients and NHRP
servers."
::= { nhrpGroups 1 }
nhrpClientGroup OBJECT-GROUP OBJECTS { nhrpClientInternetworkAddrType, nhrpClientInternetworkAddr, nhrpClientNbmaAddrType, nhrpClientNbmaAddr, nhrpClientNbmaSubaddr, nhrpClientInitialRequestTimeout, nhrpClientRegistrationRequestRetries, nhrpClientResolutionRequestRetries, nhrpClientPurgeRequestRetries, nhrpClientDefaultMtu, nhrpClientHoldTime, nhrpClientRequestID, nhrpClientStorageType, nhrpClientRowStatus, nhrpClientRegUniqueness, nhrpClientRegState, nhrpClientRegRowStatus, nhrpClientNhsInternetworkAddrType, nhrpClientNhsInternetworkAddr, nhrpClientNhsNbmaAddrType, nhrpClientNhsNbmaAddr, nhrpClientNhsNbmaSubaddr,
nhrpClientGroup对象组对象{nhrpClientInternetworkAddrType，nhrpClientInternetworkAddr，NHRPClientNbmaAddressType，NHRPClientNbmaAddress，nhrpClientNbmaSubaddr，nhrpClientInitialRequestTimeout，nhrpClientRegistrationRequestRetries，NHRPClientSolutionRequestRetries，nhrpClientPurgeRequestRetries，nhrpClientDefaultMtu，nhrpClientHoldTime，nhrpClientRequestID，nhrpClientStorageType，nhrpClientRowStatus，NHRPClientRegunique，NHRPClientRegunique，NHRPClientRegunique，nhrpClientNhsInternetworkAddrType，nhrpClientNhsInternetworkAddr，nhrpClientNhsNbmaAddr，nhrpClientNhsNbmaAddr，NHRPClientNHSNBMasubadr，
nhrpClientNhsInUse, nhrpClientNhsRowStatus, nhrpClientStatTxResolveReq, nhrpClientStatRxResolveReplyAck, nhrpClientStatRxResolveReplyNakProhibited,
NHRPClientNHASSISE、nhrpClientNhsRowStatus、nhrpClientStatTxResolveReq、nhrpClientStatRxResolveReplyAck、NHRPClientStatrXResolveReplyNak、，
nhrpClientStatRxResolveReplyNakInsufResources,
nhrpClientStatRxResolveReplyNakNoBinding,
nhrpClientStatRxResolveReplyNakNotUnique,
nhrpClientStatTxRegisterReq,
nhrpClientStatRxRegisterAck,
nhrpClientStatRxRegisterNakProhibited,
nhrpClientStatRxRegisterNakInsufResources,
nhrpClientStatRxRegisterNakAlreadyReg,
nhrpClientStatRxPurgeReq,
nhrpClientStatTxPurgeReq,
nhrpClientStatRxPurgeReply,
nhrpClientStatTxPurgeReply,
nhrpClientStatTxErrorIndication,
nhrpClientStatRxErrUnrecognizedExtension,
nhrpClientStatRxErrLoopDetected,
nhrpClientStatRxErrProtoAddrUnreachable,
nhrpClientStatRxErrProtoError,
nhrpClientStatRxErrSduSizeExceeded,
nhrpClientStatRxErrInvalidExtension,
nhrpClientStatRxErrAuthenticationFailure,
nhrpClientStatRxErrHopCountExceeded,
nhrpClientStatDiscontinuityTime
}
STATUS current
DESCRIPTION
"Objects that apply only to NHRP clients."
::= { nhrpGroups 2 }
nhrpClientStatRxResolveReplyNakInsufResources,
nhrpClientStatRxResolveReplyNakNoBinding,
nhrpClientStatRxResolveReplyNakNotUnique,
nhrpClientStatTxRegisterReq,
nhrpClientStatRxRegisterAck,
nhrpClientStatRxRegisterNakProhibited,
nhrpClientStatRxRegisterNakInsufResources,
nhrpClientStatRxRegisterNakAlreadyReg,
nhrpClientStatRxPurgeReq,
nhrpClientStatTxPurgeReq,
nhrpClientStatRxPurgeReply,
nhrpClientStatTxPurgeReply,
nhrpClientStatTxErrorIndication,
nhrpClientStatRxErrUnrecognizedExtension,
nhrpClientStatRxErrLoopDetected,
nhrpClientStatRxErrProtoAddrUnreachable,
nhrpClientStatRxErrProtoError,
nhrpClientStatRxErrSduSizeExceeded,
nhrpClientStatRxErrInvalidExtension,
nhrpClientStatRxErrAuthenticationFailure,
nhrpClientStatRxErrHopCountExceeded,
nhrpClientStatDiscontinuityTime
}
STATUS current
DESCRIPTION
"Objects that apply only to NHRP clients."
::= { nhrpGroups 2 }
nhrpServerGroup OBJECT-GROUP OBJECTS { nhrpServerInternetworkAddrType, nhrpServerInternetworkAddr, nhrpServerNbmaAddrType, nhrpServerNbmaAddr, nhrpServerNbmaSubaddr, nhrpServerStorageType, nhrpServerRowStatus, nhrpServerCacheAuthoritative, nhrpServerCacheUniqueness, nhrpServerNhcPrefixLength, nhrpServerNhcInternetworkAddrType, nhrpServerNhcInternetworkAddr, nhrpServerNhcNbmaAddrType, nhrpServerNhcNbmaAddr, nhrpServerNhcNbmaSubaddr, nhrpServerNhcInUse, nhrpServerNhcRowStatus, nhrpServerStatRxResolveReq,
nhrpServerGroup对象组对象{nhrpServerInternetworkAddrType，nhrpServerInternetworkAddr，nhrpServerNbmaAddrType，nhrpServerNbmaAddr，nhrpServerNbmaSubaddr，nhrpServerStorageType，nhrpServerRowStatus，nhrpServerCacheAuthoritative，NHRPServerCacheUnique，nhrpServerNhcPrefixLength，NHRPServerNhcinertNetworkAddr，NHRPServerNhcinertNetworkAddr，NHRPServerNHCNAAddrType，nhrpServerNhcNbmaAddr、nhrpServerNhcNbmaSubaddr、nhrpServerNhcInUse、nhrpServerNhcRowStatus、nhrpServerStatRxResolveReq、，
nhrpServerStatTxResolveReplyAck,
nhrpServerStatTxResolveReplyNakProhibited,
nhrpServerStatTxResolveReplyNakInsufResources,
nhrpServerStatTxResolveReplyNakNoBinding,
nhrpServerStatTxResolveReplyNakNotUnique,
nhrpServerStatRxRegisterReq,
nhrpServerStatTxRegisterAck,
nhrpServerStatTxRegisterNakProhibited,
nhrpServerStatTxRegisterNakInsufResources,
nhrpServerStatTxRegisterNakAlreadyReg,
nhrpServerStatRxPurgeReq,
nhrpServerStatTxPurgeReq,
nhrpServerStatRxPurgeReply,
nhrpServerStatTxPurgeReply,
nhrpServerStatRxErrUnrecognizedExtension,
nhrpServerStatRxErrLoopDetected,
nhrpServerStatRxErrProtoAddrUnreachable,
nhrpServerStatRxErrProtoError,
nhrpServerStatRxErrSduSizeExceeded,
nhrpServerStatRxErrInvalidExtension,
nhrpServerStatRxErrInvalidResReplyReceived,
nhrpServerStatRxErrAuthenticationFailure,
nhrpServerStatRxErrHopCountExceeded,
nhrpServerStatTxErrUnrecognizedExtension,
nhrpServerStatTxErrLoopDetected,
nhrpServerStatTxErrProtoAddrUnreachable,
nhrpServerStatTxErrProtoError,
nhrpServerStatTxErrSduSizeExceeded,
nhrpServerStatTxErrInvalidExtension,
nhrpServerStatTxErrAuthenticationFailure,
nhrpServerStatTxErrHopCountExceeded,
nhrpServerStatFwResolveReq,
nhrpServerStatFwResolveReply,
nhrpServerStatFwRegisterReq,
nhrpServerStatFwRegisterReply,
nhrpServerStatFwPurgeReq,
nhrpServerStatFwPurgeReply,
nhrpServerStatFwErrorIndication,
nhrpServerStatDiscontinuityTime
}
STATUS current
DESCRIPTION
"Objects that apply only to NHRP servers."
::= { nhrpGroups 3 }
nhrpServerStatTxResolveReplyAck,
nhrpServerStatTxResolveReplyNakProhibited,
nhrpServerStatTxResolveReplyNakInsufResources,
nhrpServerStatTxResolveReplyNakNoBinding,
nhrpServerStatTxResolveReplyNakNotUnique,
nhrpServerStatRxRegisterReq,
nhrpServerStatTxRegisterAck,
nhrpServerStatTxRegisterNakProhibited,
nhrpServerStatTxRegisterNakInsufResources,
nhrpServerStatTxRegisterNakAlreadyReg,
nhrpServerStatRxPurgeReq,
nhrpServerStatTxPurgeReq,
nhrpServerStatRxPurgeReply,
nhrpServerStatTxPurgeReply,
nhrpServerStatRxErrUnrecognizedExtension,
nhrpServerStatRxErrLoopDetected,
nhrpServerStatRxErrProtoAddrUnreachable,
nhrpServerStatRxErrProtoError,
nhrpServerStatRxErrSduSizeExceeded,
nhrpServerStatRxErrInvalidExtension,
nhrpServerStatRxErrInvalidResReplyReceived,
nhrpServerStatRxErrAuthenticationFailure,
nhrpServerStatRxErrHopCountExceeded,
nhrpServerStatTxErrUnrecognizedExtension,
nhrpServerStatTxErrLoopDetected,
nhrpServerStatTxErrProtoAddrUnreachable,
nhrpServerStatTxErrProtoError,
nhrpServerStatTxErrSduSizeExceeded,
nhrpServerStatTxErrInvalidExtension,
nhrpServerStatTxErrAuthenticationFailure,
nhrpServerStatTxErrHopCountExceeded,
nhrpServerStatFwResolveReq,
nhrpServerStatFwResolveReply,
nhrpServerStatFwRegisterReq,
nhrpServerStatFwRegisterReply,
nhrpServerStatFwPurgeReq,
nhrpServerStatFwPurgeReply,
nhrpServerStatFwErrorIndication,
nhrpServerStatDiscontinuityTime
}
STATUS current
DESCRIPTION
"Objects that apply only to NHRP servers."
::= { nhrpGroups 3 }
END
终止
The Internet Assigned Numbers Authority (IANA) has been and continues to be responsible for maintaining the ADDRESS FAMILY NUMBERS (http://www.isi.edu/in-notes/iana/assignments/address-family-numbers) name space assignments. The IANA has placed this list in a MIB module, such that it may be imported into other MIBs. The motivation for doing this is to allow MIBs to not have to change when a new assignment is made to the ADDRESS FAMILY NUMBERS. This is very similar to the motivation behind the IANAifType-MIB.
互联网分配号码管理局（IANA）一直并将继续负责维护地址系列号码(http://www.isi.edu/in-notes/iana/assignments/address-family-numbers)名称空间分配。IANA已将此列表放置在MIB模块中，以便可以将其导入其他MIB。这样做的动机是允许MIB在对地址族编号进行新分配时不必更改。这与IANAifType MIB背后的动机非常相似。
Any additions or changes to the list of ADDRESS FAMILY NUMBERS registered via IANA will be done as they have in the past and this document does not propose any changes to the ADDRESS FAMILY NUMBERS other than to place them into a MIB, which can be found via anonymous FTP at: ftp://ftp.isi.edu/mib/ianaaddressfamilynumbers.mib.
对通过IANA注册的地址系列号列表的任何添加或更改将与过去一样进行，本文件不建议对地址系列号进行任何更改，只是将其放入MIB中，可通过匿名FTP在以下位置找到：ftp://ftp.isi.edu/mib/ianaaddressfamilynumbers.mib.
There are a number of management objects defined in this MIB that have a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations.
此MIB中定义了许多管理对象，它们的MAX-ACCESS子句为read-write和/或read-create。在某些网络环境中，此类对象可能被视为敏感或易受攻击。在没有适当保护的非安全环境中支持SET操作可能会对网络操作产生负面影响。
The NHRP Protocol, RFC 2332 [17], Section 5.2.4.4 discusses security. There is an authentication option which should be utilized to authenticate the source and also provide data integrity to the NHRP payload. This MIB does not contain any managed objects which configure or expose security information such as that needed for NHRP authentication or data integrity.
NHRP协议RFC 2332[17]第5.2.4.4节讨论了安全性。有一个身份验证选项，该选项应用于对源进行身份验证，并为NHRP有效负载提供数据完整性。此MIB不包含任何配置或公开安全信息（如NHRP身份验证或数据完整性所需的信息）的托管对象。
The following items were deemed to jeopardize security and thus, were NOT added to this MIB. Items denoted as (configurable) are those which would need values. Items denoted as (read-only) are those which would provide information. Although the NHRP Protocol [17], requires or has this information, exposing it in a MIB would jeopardize the entire NBMA domain where NHRP was being used. Therefore, these items have been omitted from the MIB.
以下项目被视为危害安全，因此未添加到此MIB中。表示为（可配置）的项目是那些需要值的项目。表示为（只读）的项目是提供信息的项目。尽管NHRP协议[17]要求或拥有该信息，但将其暴露在MIB中会危及使用NHRP的整个NBMA域。因此，MIB中省略了这些项目。
1. (configurable) enable/disable security 2. (configurable) SPI (security parameter index). Depending upon the implementation, there may be multiple SPIs, and these would be configurable also. For example, if the implementation switched to a different SPI after a given time. 3. (configurable) algorithm. The HMAC-MD5-128 is the default hash algorithm. 4. (configurable) lifetime value in seconds. 5. (read-only) key. 6. (read-only) list of users who have access to the above information.
1. （可配置）启用/禁用安全2。（可配置）SPI（安全参数索引）。根据实现的不同，可能会有多个SPI，并且这些SPI也是可配置的。例如，如果实现在给定时间后切换到不同的SPI。3.（可配置）算法。HMAC-MD5-128是默认的哈希算法。4.（可配置）以秒为单位的生存期值。5.（只读）键。6.（只读）有权访问上述信息的用户列表。
The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification can be obtained from the IETF Secretariat.
IETF对可能声称与本文件所述技术的实施或使用有关的任何知识产权或其他权利的有效性或范围，或此类权利下的任何许可可能或可能不可用的程度，不采取任何立场；它也不表示它已作出任何努力来确定任何此类权利。有关IETF在标准跟踪和标准相关文件中权利的程序信息，请参见BCP-11。可从IETF秘书处获得可供发布的权利声明副本和任何许可证保证，或本规范实施者或用户试图获得使用此类专有权利的一般许可证或许可的结果。
The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director.
IETF邀请任何相关方提请其注意任何版权、专利或专利申请，或其他可能涉及实施本标准所需技术的专有权利。请将信息发送给IETF执行董事。
This document is a product of the IETF's Internetworking Over NBMA Networks (ion) Working Group.
本文件是IETF的NBMA网络互联（ion）工作组的产品。
The authors would like to thank Avri Doria (Bytex) for the first draft of the NHRP MIB and Keith McCloghrie (cisco) and David Horton (CITR) for their feedback and suggestions. Also, we would like to thank Naganand Doraswamy (Bay Networks) for assistance with the "Security Considerations" section.
作者要感谢Avri Doria（Bytex）提供的NHRP MIB初稿，以及Keith McCloghrie（cisco）和David Horton（CITR）提供的反馈和建议。此外，我们还要感谢Naganand Doraswamy（海湾网络）在“安全考虑”部分提供的帮助。
[1] Harrington, D., Presuhn, R. and B. Wijnen, "An Architecture for Describing SNMP Management Frameworks", RFC 2571, April 1999.
[1] Harrington，D.，Presohn，R.和B.Wijnen，“描述SNMP管理框架的体系结构”，RFC 2571，1999年4月。
[2] Rose, M. and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP-based Internets", STD 16, RFC 1155, May 1990.
[2] Rose，M.和K.McCloghrie，“基于TCP/IP的互联网管理信息的结构和识别”，STD 16，RFC 1155，1990年5月。
[3] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD 16, RFC 1212, March 1991.
[3] Rose，M.和K.McCloghrie，“简明MIB定义”，STD 16，RFC 1212，1991年3月。
[4] Rose, M., "A Convention for Defining Traps for use with the SNMP", RFC 1215, March 1991.
[4] Rose，M.“定义用于SNMP的陷阱的约定”，RFC1215，1991年3月。
[5] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[5] McCloghrie，K.，Perkins，D.，Schoenwaeld，J.，Case，J.，Rose，M.和S.Waldbusser，“管理信息的结构版本2（SMIv2）”，STD 58，RFC 2578，1999年4月。
[6] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999.
[6] McCloghrie，K.，Perkins，D.，Schoenwaeld，J.，Case，J.，Rose，M.和S.Waldbusser，“SMIv2的文本约定”，STD 58，RFC 2579，1999年4月。
[7] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999.
[7] McCloghrie，K.，Perkins，D.，Schoenwaeld，J.，Case，J.，Rose，M.和S.Waldbusser，“SMIv2的一致性声明”，STD 58，RFC 25801999年4月。
[8] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple Network Management Protocol", STD 15, RFC 1157, May 1990.
[8] Case，J.，Fedor，M.，Schoffstall，M.和J.Davin，“简单网络管理协议”，STD 15，RFC 1157，1990年5月。
[9] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901, January 1996.
[9] Case，J.，McCloghrie，K.，Rose，M.和S.Waldbusser，“基于社区的SNMPv2简介”，RFC 19011996年1月。
[10] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1906, January 1996.
[10] Case，J.，McCloghrie，K.，Rose，M.和S.Waldbusser，“简单网络管理协议（SNMPv2）版本2的传输映射”，RFC 1906，1996年1月。
[11] Case, J., Harrington D., Presuhn R. and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)", RFC 2572, April 1999.
[11] Case，J.，Harrington D.，Presohn R.和B.Wijnen，“简单网络管理协议（SNMP）的消息处理和调度”，RFC 2572，1999年4月。
[12] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", RFC 2574, April 1999.
[12] Blumenthal，U.和B.Wijnen，“简单网络管理协议（SNMPv3）第3版的基于用户的安全模型（USM）”，RFC 2574，1999年4月。
[13] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, January 1996.
[13] Case，J.，McCloghrie，K.，Rose，M.和S.Waldbusser，“简单网络管理协议（SNMPv2）版本2的协议操作”，RFC 1905，1996年1月。
[14] Levi, D., Meyer, P. and B. Stewart, "SNMPv3 Applications", RFC 2573, April 1999.
[14] Levi，D.，Meyer，P.和B.Stewart，“SNMPv3应用”，RFC2573，1999年4月。
[15] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2575, April 1999.
[15] Wijnen，B.，Presuhn，R.和K.McCloghrie，“用于简单网络管理协议（SNMP）的基于视图的访问控制模型（VACM）”，RFC2575，1999年4月。
[16] Case, J., Mundy, R., Partain, D. and B. Stewart, "Introduction to Version 3 of the Internet-standard Network Management Framework", RFC 2570, April 1999.
[16] Case，J.，Mundy，R.，Partain，D.和B.Stewart，“互联网标准网络管理框架第3版简介”，RFC 25701999年4月。
[17] Luciani, J. V., Katz, D., Piscitello, D. and B. Cole, "NBMA Next Hop Resolution Protocol (NHRP)", RFC 2332, December 1997.
[17] Luciani，J.V.，Katz，D.，Piscitello，D.和B.Cole，“NBMA下一跳解决方案（NHRP）”，RFC 2332，1997年12月。
[18] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB using SMIv2", RFC 2233, November 1997.
[18] McCloghrie，K.和F.Kastenholz，“使用SMIv2的接口组MIB”，RFC 2233，1997年11月。
[19] Tesink, K., Editor, "Definitions of Managed Objects for ATM Management", RFC 2515, February 1999.
[19] Tesink，K.，编辑，“ATM管理的托管对象定义”，RFC2515，1999年2月。
[20] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 2434, October 1998.
[20] Narten，T.和H.Alvestrand，“在RFCs中编写IANA注意事项部分的指南”，BCP 26，RFC 2434，1998年10月。
[21] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.
[21] Bradner，S.，“RFC中用于表示需求水平的关键词”，BCP 14，RFC 2119，1997年3月。
[22] Bradner, S., "The Internet Standards Process -- Revision 3", BCP 9, RFC 2026, October 1996.
[22] Bradner，S.，“互联网标准过程——第3版”，BCP 9，RFC 2026，1996年10月。
[23] Cucchiara, J., editor, "Multiprotocol Over ATM Version 1.0 MIB", af-mpoa-0092.000, ATM Forum, July 1998.
[23] Cucchiara，J.，编辑，“ATM上的多协议版本1.0 MIB”，af-mpoa-0092.000，ATM论坛，1998年7月。
[24] Fredette, A., editor, "Multiprotocol Over ATM Version 1.0", af-mpoa-0087.000, ATM Forum, May 1997.
[24] Fredette，A.，编辑，“ATM版本1.0上的多协议”，af-mpoa-0087.000，ATM论坛，1997年5月。
[25] Laubach, M., and J. Halpern, "Classical IP and ARP over ATM", RFC 2225, April 1998.
[25] Laubach，M.和J.Halpern，“ATM上的经典IP和ARP”，RFC 22251998年4月。
[26] Greene, M., J. Luciani, K. White and T. Kuo, "Definitions of Managed Objects for Classical IP and ARP Over ATM Using SMIv2", RFC 2320, April 1998.
[26] Greene，M.，J.Luciani，K.White和T.Kuo，“使用SMIv2的ATM上传统IP和ARP的托管对象定义”，RFC 2320，1998年4月。
James V. Luciani Bay Networks 3 Federal Street Mail Stop: BL3-03 Billerica, MA 01821
James V.Luciani Bay Networks 3联邦街道邮件站：BL3-03马萨诸塞州比尔里卡01821
Phone: (978) 288-4734 EMail: luciani@baynetworks.com
电话：（978）288-4734电子邮件：luciani@baynetworks.com
Maria Greene Contractor Xedia, Corp. 119 Russell Dr. Littleton, MA 01460
Maria Greene承包商Xedia，Corp.119马萨诸塞州罗素·利特尔顿博士01460
EMail: maria@xedia.com
EMail: maria@xedia.com
Joan Cucchiara IronBridge Networks 55 Hayden Ave. Lexington, MA 02421
马萨诸塞州列克星敦海登大道55号Joan Cucchiara IronBridge Networks 02421
Phone: (781) 372-8236 EMail: joan@ironbridgenetworks.com
电话：（781）372-8236电子邮件：joan@ironbridgenetworks.com
Copyright (C) The Internet Society (1999). All Rights Reserved.
版权所有（C）互联网协会（1999年）。版权所有。
This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English.
本文件及其译本可复制并提供给他人，对其进行评论或解释或协助其实施的衍生作品可全部或部分编制、复制、出版和分发，不受任何限制，前提是上述版权声明和本段包含在所有此类副本和衍生作品中。但是，不得以任何方式修改本文件本身，例如删除版权通知或对互联网协会或其他互联网组织的引用，除非出于制定互联网标准的需要，在这种情况下，必须遵循互联网标准过程中定义的版权程序，或根据需要将其翻译成英语以外的其他语言。
The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns.
上述授予的有限许可是永久性的，互联网协会或其继承人或受让人不会撤销。
This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
本文件和其中包含的信息是按“原样”提供的，互联网协会和互联网工程任务组否认所有明示或暗示的保证，包括但不限于任何保证，即使用本文中的信息不会侵犯任何权利，或对适销性或特定用途适用性的任何默示保证。
Acknowledgement
确认
Funding for the RFC Editor function is currently provided by the Internet Society.
RFC编辑功能的资金目前由互联网协会提供。